[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <471533AF.60100@rtr.ca>
Date: Tue, 16 Oct 2007 17:57:03 -0400
From: Mark Lord <lkml@....ca>
To: Kristen Carlson Accardi <kristen.c.accardi@...el.com>
Cc: Greg KH <greg@...ah.com>,
Linux Kernel <linux-kernel@...r.kernel.org>,
pcihpd-discuss@...ts.sourceforge.net,
Andrew Morton <akpm@...ux-foundation.org>
Subject: [PATCH] Fix PCIe hotplug for Dell notebook ExpressCard slots
Fix PCIe Hotplug so that it works with ExpressCard slots on Dell notebooks
in conjunction with modparam of pciehp_force=1.
The PCIe Hotplug driver has two shortcomings when used on Dell notebooks
which lack ACPI BIOS support for PCIe hotplug:
1. The driver does not recognise cards that were inserted prior
to the driver being modprobe'd.
2. The driver stops functioning after a suspend/resume (RAM) cycle,
and needs to be rmmod'd and modprobe'd to get it working again.
This patch addresses both issues.
Issue 1 is fixed by modifying pciehp_probe() to either enable or disable
the slot based on whether or not a card is detected at module init time.
Issue 2 is fixed by implementing pciehp_resume() to do the same
after having it first reinitialize the slot event registers.
The code to reinitialize those registers has been broken away from
pcie_init() so that it can be shared with pciehp_resume().
I'm not certain that locking contraints are correct in pciehp_resume(),
so it would be quite useful for the PCIe hotplug folks to look this all
over and provide suggestions/fixes as needed.
There are also a few minor cosmetic changes to satisfy checkpatch.pl.
pciehp.h | 3
pciehp_core.c | 31 ++++++--
pciehp_ctrl.c | 4 -
pciehp_hpc.c | 207 +++++++++++++++++++++++++++++++++-------------------------
4 files changed, 144 insertions(+), 101 deletions(-)
Signed-off-by: Mark Lord <mlord@...ox.com>
---
--- old/drivers/pci/hotplug/pciehp.h 2007-10-12 12:43:44.000000000 -0400
+++ linux/drivers/pci/hotplug/pciehp.h 2007-10-16 17:53:48.000000000 -0400
@@ -161,6 +161,9 @@
extern int pciehp_unconfigure_device(struct slot *p_slot);
extern void pciehp_queue_pushbutton_work(struct work_struct *work);
int pcie_init(struct controller *ctrl, struct pcie_device *dev);
+int pciehp_enable_slot(struct slot *p_slot);
+int pciehp_disable_slot(struct slot *p_slot);
+int pcie_init_enable_events(struct controller *ctrl, struct pcie_device *dev);
static inline struct slot *pciehp_find_slot(struct controller *ctrl, u8 device)
{
--- old/drivers/pci/hotplug/pciehp_core.c 2007-10-12 12:43:44.000000000 -0400
+++ linux/drivers/pci/hotplug/pciehp_core.c 2007-10-16 17:48:24.000000000 -0400
@@ -470,17 +470,14 @@
t_slot = pciehp_find_slot(ctrl, ctrl->slot_device_offset);
- t_slot->hpc_ops->get_adapter_status(t_slot, &value); /* Check if slot is occupied */
- if ((POWER_CTRL(ctrl->ctrlcap)) && !value) {
- rc = t_slot->hpc_ops->power_off_slot(t_slot); /* Power off slot if not occupied*/
- if (rc)
- goto err_out_free_ctrl_slot;
- }
-
+ /* Check if slot is occupied */
+ t_slot->hpc_ops->get_adapter_status(t_slot, &value);
+ if (value)
+ pciehp_enable_slot(t_slot);
+ else
+ pciehp_disable_slot(t_slot);
return 0;
-err_out_free_ctrl_slot:
- cleanup_slots(ctrl);
err_out_release_ctlr:
ctrl->hpc_ops->release_ctlr(ctrl);
err_out_free_ctrl:
@@ -508,7 +505,23 @@
static int pciehp_resume (struct pcie_device *dev)
{
+ struct pci_dev *pdev = dev->port;
+ struct controller *ctrl = pci_get_drvdata(pdev);
+ struct slot *t_slot;
+ u8 status;
+
printk("%s ENTRY\n", __FUNCTION__);
+
+ pcie_init_enable_events(ctrl, dev);
+
+ t_slot = pciehp_find_slot(ctrl, ctrl->slot_device_offset);
+
+ /* Check if slot is occupied */
+ t_slot->hpc_ops->get_adapter_status(t_slot, &status);
+ if (status)
+ pciehp_enable_slot(t_slot);
+ else
+ pciehp_disable_slot(t_slot);
return 0;
}
#endif
--- old/drivers/pci/hotplug/pciehp_ctrl.c 2007-10-12 12:43:44.000000000 -0400
+++ linux/drivers/pci/hotplug/pciehp_ctrl.c 2007-10-16 16:53:35.000000000 -0400
@@ -37,8 +37,6 @@
#include "pciehp.h"
static void interrupt_event_handler(struct work_struct *work);
-static int pciehp_enable_slot(struct slot *p_slot);
-static int pciehp_disable_slot(struct slot *p_slot);
static int queue_interrupt_event(struct slot *p_slot, u32 event_type)
{
@@ -520,7 +518,7 @@
case INT_PRESENCE_OFF:
if (!HP_SUPR_RM(ctrl->ctrlcap))
break;
- dbg("Surprise Removal\n");
+ dbg("Surprise Event\n");
update_slot_info(p_slot);
handle_surprise_event(p_slot);
break;
--- old/drivers/pci/hotplug/pciehp_hpc.c 2007-10-12 12:43:44.000000000 -0400
+++ linux/drivers/pci/hotplug/pciehp_hpc.c 2007-10-16 17:53:27.000000000 -0400
@@ -1163,100 +1163,23 @@
}
#endif
-
-
-int pcie_init(struct controller * ctrl, struct pcie_device *dev)
+int pcie_init_enable_events(struct controller *ctrl, struct pcie_device *dev)
{
int rc;
u16 temp_word;
- u16 cap_reg;
u16 intr_enable = 0;
u32 slot_cap;
- int cap_base;
- u16 slot_status, slot_ctrl;
+ u16 slot_status;
struct pci_dev *pdev;
DBG_ENTER_ROUTINE
-
- pdev = dev->port;
- ctrl->pci_dev = pdev; /* save pci_dev in context */
-
- dbg("%s: hotplug controller vendor id 0x%x device id 0x%x\n",
- __FUNCTION__, pdev->vendor, pdev->device);
-
- if ((cap_base = pci_find_capability(pdev, PCI_CAP_ID_EXP)) == 0) {
- dbg("%s: Can't find PCI_CAP_ID_EXP (0x10)\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
-
- ctrl->cap_base = cap_base;
-
- dbg("%s: pcie_cap_base %x\n", __FUNCTION__, cap_base);
-
- rc = pciehp_readw(ctrl, CAPREG, &cap_reg);
- if (rc) {
- err("%s: Cannot read CAPREG register\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
- dbg("%s: CAPREG offset %x cap_reg %x\n",
- __FUNCTION__, ctrl->cap_base + CAPREG, cap_reg);
-
- if (((cap_reg & SLOT_IMPL) == 0) || (((cap_reg & DEV_PORT_TYPE) != 0x0040)
- && ((cap_reg & DEV_PORT_TYPE) != 0x0060))) {
- dbg("%s : This is not a root port or the port is not connected to a slot\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
+ pdev = dev->port;
rc = pciehp_readl(ctrl, SLOTCAP, &slot_cap);
if (rc) {
err("%s: Cannot read SLOTCAP register\n", __FUNCTION__);
goto abort_free_ctlr;
}
- dbg("%s: SLOTCAP offset %x slot_cap %x\n",
- __FUNCTION__, ctrl->cap_base + SLOTCAP, slot_cap);
-
- if (!(slot_cap & HP_CAP)) {
- dbg("%s : This slot is not hot-plug capable\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
- /* For debugging purpose */
- rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status);
- if (rc) {
- err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
- dbg("%s: SLOTSTATUS offset %x slot_status %x\n",
- __FUNCTION__, ctrl->cap_base + SLOTSTATUS, slot_status);
-
- rc = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl);
- if (rc) {
- err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__);
- goto abort_free_ctlr;
- }
- dbg("%s: SLOTCTRL offset %x slot_ctrl %x\n",
- __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_ctrl);
-
- for ( rc = 0; rc < DEVICE_COUNT_RESOURCE; rc++)
- if (pci_resource_len(pdev, rc) > 0)
- dbg("pci resource[%d] start=0x%llx(len=0x%llx)\n", rc,
- (unsigned long long)pci_resource_start(pdev, rc),
- (unsigned long long)pci_resource_len(pdev, rc));
-
- info("HPC vendor_id %x device_id %x ss_vid %x ss_did %x\n", pdev->vendor, pdev->device,
- pdev->subsystem_vendor, pdev->subsystem_device);
-
- mutex_init(&ctrl->crit_sect);
- mutex_init(&ctrl->ctrl_lock);
- spin_lock_init(&ctrl->lock);
-
- /* setup wait queue */
- init_waitqueue_head(&ctrl->queue);
-
- /* return PCI Controller Info */
- ctrl->slot_device_offset = 0;
- ctrl->num_slots = 1;
- ctrl->first_slot = slot_cap >> 19;
- ctrl->ctrlcap = slot_cap & 0x0000007f;
/* Mask Hot-plug Interrupt Enable */
rc = pciehp_readw(ctrl, SLOTCTRL, &temp_word);
@@ -1267,7 +1190,7 @@
dbg("%s: SLOTCTRL %x value read %x\n",
__FUNCTION__, ctrl->cap_base + SLOTCTRL, temp_word);
- temp_word = (temp_word & ~HP_INTR_ENABLE & ~CMD_CMPL_INTR_ENABLE) | 0x00;
+ temp_word = (temp_word & ~HP_INTR_ENABLE & ~CMD_CMPL_INTR_ENABLE)|0x00;
rc = pciehp_writew(ctrl, SLOTCTRL, temp_word);
if (rc) {
@@ -1330,14 +1253,14 @@
if (ATTN_BUTTN(slot_cap))
intr_enable = intr_enable | ATTN_BUTTN_ENABLE;
-
+
if (POWER_CTRL(slot_cap))
intr_enable = intr_enable | PWR_FAULT_DETECT_ENABLE;
-
+
if (MRL_SENS(slot_cap))
intr_enable = intr_enable | MRL_DETECT_ENABLE;
- temp_word = (temp_word & ~intr_enable) | intr_enable;
+ temp_word = (temp_word & ~intr_enable) | intr_enable;
if (pciehp_poll_mode) {
temp_word = (temp_word & ~HP_INTR_ENABLE) | 0x0;
@@ -1345,7 +1268,7 @@
temp_word = (temp_word & ~HP_INTR_ENABLE) | HP_INTR_ENABLE;
}
- /* Unmask Hot-plug Interrupt Enable for the interrupt notification mechanism case */
+ /* Unmask hp Interrupt Enable for intr notification mechanism case */
rc = pciehp_writew(ctrl, SLOTCTRL, temp_word);
if (rc) {
err("%s: Cannot write to SLOTCTRL register\n", __FUNCTION__);
@@ -1356,14 +1279,14 @@
err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__);
goto abort_disable_intr;
}
-
+
temp_word = 0x1F; /* Clear all events */
rc = pciehp_writew(ctrl, SLOTSTATUS, temp_word);
if (rc) {
err("%s: Cannot write to SLOTSTATUS register\n", __FUNCTION__);
goto abort_disable_intr;
}
-
+
if (pciehp_force) {
dbg("Bypassing BIOS check for pciehp use on %s\n",
pci_name(ctrl->pci_dev));
@@ -1373,8 +1296,6 @@
goto abort_disable_intr;
}
- ctrl->hpc_ops = &pciehp_hpc_ops;
-
DBG_LEAVE_ROUTINE
return 0;
@@ -1398,3 +1319,111 @@
DBG_LEAVE_ROUTINE
return -1;
}
+
+int pcie_init(struct controller *ctrl, struct pcie_device *dev)
+{
+ int rc;
+ u16 cap_reg;
+ u32 slot_cap;
+ int cap_base;
+ u16 slot_status, slot_ctrl;
+ struct pci_dev *pdev;
+
+ DBG_ENTER_ROUTINE
+
+ pdev = dev->port;
+ ctrl->pci_dev = pdev; /* save pci_dev in context */
+
+ dbg("%s: hotplug controller vendor id 0x%x device id 0x%x\n",
+ __FUNCTION__, pdev->vendor, pdev->device);
+
+ cap_base = pci_find_capability(pdev, PCI_CAP_ID_EXP);
+ if (cap_base == 0) {
+ dbg("%s: Can't find PCI_CAP_ID_EXP (0x10)\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+
+ ctrl->cap_base = cap_base;
+
+ dbg("%s: pcie_cap_base %x\n", __FUNCTION__, cap_base);
+
+ rc = pciehp_readw(ctrl, CAPREG, &cap_reg);
+ if (rc) {
+ err("%s: Cannot read CAPREG register\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+ dbg("%s: CAPREG offset %x cap_reg %x\n",
+ __FUNCTION__, ctrl->cap_base + CAPREG, cap_reg);
+
+ if (((cap_reg & SLOT_IMPL) == 0)
+ || (((cap_reg & DEV_PORT_TYPE) != 0x0040)
+ && ((cap_reg & DEV_PORT_TYPE) != 0x0060))) {
+ dbg("%s : This is not a root port"
+ " or the port is not connected to a slot\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+
+ rc = pciehp_readl(ctrl, SLOTCAP, &slot_cap);
+ if (rc) {
+ err("%s: Cannot read SLOTCAP register\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+ dbg("%s: SLOTCAP offset %x slot_cap %x\n",
+ __FUNCTION__, ctrl->cap_base + SLOTCAP, slot_cap);
+
+ if (!(slot_cap & HP_CAP)) {
+ dbg("%s : This slot is not hot-plug capable\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+ /* For debugging purpose */
+ rc = pciehp_readw(ctrl, SLOTSTATUS, &slot_status);
+ if (rc) {
+ err("%s: Cannot read SLOTSTATUS register\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+ dbg("%s: SLOTSTATUS offset %x slot_status %x\n",
+ __FUNCTION__, ctrl->cap_base + SLOTSTATUS, slot_status);
+
+ rc = pciehp_readw(ctrl, SLOTCTRL, &slot_ctrl);
+ if (rc) {
+ err("%s: Cannot read SLOTCTRL register\n", __FUNCTION__);
+ goto abort_free_ctlr;
+ }
+ dbg("%s: SLOTCTRL offset %x slot_ctrl %x\n",
+ __FUNCTION__, ctrl->cap_base + SLOTCTRL, slot_ctrl);
+
+ for (rc = 0; rc < DEVICE_COUNT_RESOURCE; rc++)
+ if (pci_resource_len(pdev, rc) > 0)
+ dbg("pci resource[%d] start=0x%llx(len=0x%llx)\n", rc,
+ (unsigned long long)pci_resource_start(pdev, rc),
+ (unsigned long long)pci_resource_len(pdev, rc));
+
+ info("HPC vendor_id %x device_id %x ss_vid %x"
+ " ss_did %x\n", pdev->vendor, pdev->device,
+ pdev->subsystem_vendor, pdev->subsystem_device);
+
+ mutex_init(&ctrl->crit_sect);
+ mutex_init(&ctrl->ctrl_lock);
+ spin_lock_init(&ctrl->lock);
+
+ /* setup wait queue */
+ init_waitqueue_head(&ctrl->queue);
+
+ /* return PCI Controller Info */
+ ctrl->slot_device_offset = 0;
+ ctrl->num_slots = 1;
+ ctrl->first_slot = slot_cap >> 19;
+ ctrl->ctrlcap = slot_cap & 0x0000007f;
+
+ rc = pcie_init_enable_events(ctrl, dev);
+ if (rc)
+ goto abort_free_ctlr;;
+
+ ctrl->hpc_ops = &pciehp_hpc_ops;
+
+ DBG_LEAVE_ROUTINE
+ return 0;
+abort_free_ctlr:
+ DBG_LEAVE_ROUTINE
+ return -1;
+}
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists