| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1192790946.6416.4.camel@localhost> Date: Fri, 19 Oct 2007 05:49:06 -0500 From: Chris Holvenstot <cholvenstot@...cast.net> To: "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org> Subject: Network failure with 2.6.23-git14 I built 2.6.23-git14 this morning - when booted I can not access the network via my Ethernet connection. Fallback to 2.6.23-git11 works OK. One interesting message during boot: sysctl table check failed: /net/token-ring .3.14 procname does not match binary path procname Complete dmesg output follows [ 0.000000] Linux version 2.6.23-git14 (root@...eye) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #1 SMP Fri Oct 19 04:31:31 CDT 2007 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable) [ 0.000000] BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] 1151MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] found SMP MP-table at 000f5380 [ 0.000000] Entering add_active_range(0, 0, 524272) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 524272 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 524272 [ 0.000000] On node 0 totalpages: 524272 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 2303 pages used for memmap [ 0.000000] HighMem zone: 292593 pages, LIFO batch:31 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000F9260, 0014 (r0 Nvidia) [ 0.000000] ACPI: RSDT 7FFF3040, 0030 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: FACP 7FFF30C0, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: DSDT 7FFF3180, 63C4 (r1 NVIDIA AWRDACPI 1000 MSFT 100000E) [ 0.000000] ACPI: FACS 7FFF0000, 0040 [ 0.000000] ACPI: MCFG 7FFF9680, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 0) [ 0.000000] ACPI: APIC 7FFF95C0, 0072 (r1 Nvidia AWRDACPI 42302E31 AWRD 0) [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] If you got timer trouble try acpi_use_timer_override [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:11 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] Processor #1 15:11 APIC version 16 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520177 [ 0.000000] Kernel command line: root=UUID=4dc2e6b0-c980-418b-8ad0-98358e7ec47d ro quiet single [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 2412.413 MHz processor. [ 32.950316] spurious 8259A interrupt: IRQ7. [ 32.951445] Console: colour VGA+ 80x25 [ 32.951448] console [tty0] enabled [ 32.951927] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 32.952336] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 33.024846] Memory: 2035932k/2097088k available (2031k kernel code, 59964k reserved, 940k data, 336k init, 1179584k highmem) [ 33.024852] virtual kernel memory layout: [ 33.024853] fixmap : 0xfff9b000 - 0xfffff000 ( 400 kB) [ 33.024854] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 33.024855] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 33.024856] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 33.024857] .init : 0xc03ed000 - 0xc0441000 ( 336 kB) [ 33.024858] .data : 0xc02fbe0f - 0xc03e7084 ( 940 kB) [ 33.024858] .text : 0xc0100000 - 0xc02fbe0f (2031 kB) [ 33.024861] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 33.104900] Calibrating delay using timer specific routine.. 4827.67 BogoMIPS (lpj=9655356) [ 33.104935] Security Framework initialized [ 33.104941] SELinux: Disabled at boot. [ 33.104955] Mount-cache hash table entries: 512 [ 33.105095] CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 00000000 [ 33.105100] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 33.105102] CPU: L2 Cache: 512K (64 bytes/line) [ 33.105104] CPU 0(2) -> Core 0 [ 33.105105] CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003 00000000 [ 33.105114] Compat vDSO mapped to ffffe000. [ 33.105125] Checking 'hlt' instruction... OK. [ 33.121092] SMP alternatives: switching to UP code [ 33.121535] ACPI: Core revision 20070126 [ 33.125279] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 01 [ 33.125296] SMP alternatives: switching to SMP code [ 33.125553] Booting processor 1/1 eip 3000 [ 33.135799] Initializing CPU#1 [ 33.213068] Calibrating delay using timer specific routine.. 4825.06 BogoMIPS (lpj=9650126) [ 33.213073] CPU: After generic identify, caps: 178bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000003 00000000 [ 33.213078] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 33.213080] CPU: L2 Cache: 512K (64 bytes/line) [ 33.213081] CPU 1(2) -> Core 1 [ 33.213082] CPU: After all inits, caps: 178bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000003 00000000 [ 33.212931] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 01 [ 33.212938] Total of 2 processors activated (9652.74 BogoMIPS). [ 33.213075] ENABLING IO-APIC IRQs [ 33.213260] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 [ 33.360749] Brought up 2 CPUs [ 33.360780] CPU0 attaching sched-domain: [ 33.360782] domain 0: span 3 [ 33.360784] groups: 1 2 [ 33.360786] CPU1 attaching sched-domain: [ 33.360787] domain 0: span 3 [ 33.360789] groups: 2 1 [ 33.360962] net_namespace: 64 bytes [ 33.361222] [ 33.361471] Time: 5:34:19 Date: 10/19/07 [ 33.361502] NET: Registered protocol family 16 [ 33.361637] EISA bus registered [ 33.361641] ACPI: bus type pci registered [ 33.361702] PCI: Using MMCONFIG [ 33.361723] PCI: No mmconfig possible on device 00:18 [ 33.362016] Setting up standard PCI resources [ 33.366555] ACPI: EC: Look up EC in DSDT [ 33.372064] ACPI: Interpreter enabled [ 33.372066] ACPI: (supports S0 S1 S5) [ 33.372074] ACPI: Using IOAPIC for interrupt routing [ 33.378909] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 33.379226] PCI: Transparent bridge - 0000:00:09.0 [ 33.379483] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 33.379700] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 33.427995] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.428144] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.428293] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15) [ 33.428439] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.428591] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.428742] ACPI: PCI Interrupt Link [LUBA] (IRQs *3 4 5 7 9 10 11 12 14 15) [ 33.428889] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.429038] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12 14 15) [ 33.429186] ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 7 9 10 11 12 14 15) [ 33.429333] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 *10 11 12 14 15) [ 33.429482] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 *11 12 14 15) [ 33.429630] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15) [ 33.429777] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.429932] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15) [ 33.430086] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15) [ 33.430238] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. [ 33.430401] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. [ 33.430558] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 33.430714] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0 [ 33.430870] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 33.430977] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. [ 33.431138] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0 [ 33.431299] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. [ 33.431460] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0 [ 33.431620] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0 [ 33.431779] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0 [ 33.431939] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0 [ 33.432098] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0 [ 33.432258] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 33.432424] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0 [ 33.432591] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0 [ 33.432757] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. [ 33.432856] Linux Plug and Play Support v0.97 (c) Adam Belay [ 33.432875] pnp: PnP ACPI init [ 33.432880] ACPI: bus type pnp registered [ 33.436851] pnp: PnP ACPI: found 14 devices [ 33.436853] ACPI: ACPI bus type pnp unregistered [ 33.436856] PnPBIOS: Disabled by ACPI PNP [ 33.436969] PCI: Using ACPI for IRQ routing [ 33.436972] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 33.448561] NET: Registered protocol family 8 [ 33.448562] NET: Registered protocol family 20 [ 33.460548] system 00:01: ioport range 0x4000-0x407f has been reserved [ 33.460550] system 00:01: ioport range 0x4080-0x40ff has been reserved [ 33.460552] system 00:01: ioport range 0x4400-0x447f has been reserved [ 33.460554] system 00:01: ioport range 0x4480-0x44ff has been reserved [ 33.460556] system 00:01: ioport range 0x4800-0x487f has been reserved [ 33.460558] system 00:01: ioport range 0x4880-0x48ff has been reserved [ 33.460567] system 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved [ 33.460571] system 00:0d: iomem range 0xf0000-0xf3fff could not be reserved [ 33.460573] system 00:0d: iomem range 0xf4000-0xf7fff could not be reserved [ 33.460575] system 00:0d: iomem range 0xf8000-0xfbfff could not be reserved [ 33.460577] system 00:0d: iomem range 0xfc000-0xfffff could not be reserved [ 33.490814] PCI: Bridge: 0000:00:09.0 [ 33.490817] IO window: a000-afff [ 33.490819] MEM window: fde00000-fdefffff [ 33.490821] PREFETCH window: fdf00000-fdffffff [ 33.490823] PCI: Bridge: 0000:00:0b.0 [ 33.490824] IO window: 9000-9fff [ 33.490826] MEM window: fdd00000-fddfffff [ 33.490828] PREFETCH window: fdc00000-fdcfffff [ 33.490829] PCI: Bridge: 0000:00:0c.0 [ 33.490831] IO window: 8000-8fff [ 33.490833] MEM window: fdb00000-fdbfffff [ 33.490834] PREFETCH window: fda00000-fdafffff [ 33.490836] PCI: Bridge: 0000:00:0d.0 [ 33.490838] IO window: 7000-7fff [ 33.490840] MEM window: fd900000-fd9fffff [ 33.490841] PREFETCH window: fd800000-fd8fffff [ 33.490845] PCI: Bridge: 0000:00:0e.0 [ 33.490847] IO window: 6000-6fff [ 33.490848] MEM window: fa000000-fcffffff [ 33.490850] PREFETCH window: d0000000-dfffffff [ 33.490856] PCI: Setting latency timer of device 0000:00:09.0 to 64 [ 33.490862] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 33.490867] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 33.490872] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 33.490876] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 33.490900] NET: Registered protocol family 2 [ 33.492494] Time: acpi_pm clocksource has been installed. [ 33.492507] Switched to high resolution mode on CPU 0 [ 33.492899] Switched to high resolution mode on CPU 1 [ 33.528502] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 33.528809] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 33.530374] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 33.530904] TCP: Hash tables configured (established 131072 bind 65536) [ 33.530907] TCP reno registered [ 33.540559] checking if image is initramfs... it is [ 36.104262] Freeing initrd memory: 38951k freed [ 36.105226] audit: initializing netlink socket (disabled) [ 36.105239] audit(1192772061.980:1): initialized [ 36.105392] highmem bounce pool size: 64 pages [ 36.105461] VFS: Disk quotas dquot_6.5.1 [ 36.105480] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 36.105543] io scheduler noop registered [ 36.105544] io scheduler anticipatory registered [ 36.105545] io scheduler deadline registered [ 36.105556] io scheduler cfq registered (default) [ 36.118313] PCI: Linking AER extended capability on 0000:00:0b.0 [ 36.118316] PCI: Linking AER extended capability on 0000:00:0c.0 [ 36.118319] PCI: Linking AER extended capability on 0000:00:0d.0 [ 36.118321] PCI: Linking AER extended capability on 0000:00:0e.0 [ 36.118327] Boot video device is 0000:05:00.0 [ 36.118407] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 36.118421] assign_interrupt_mode Found MSI capability [ 36.118422] Allocate Port Service[0000:00:0b.0:pcie00] [ 36.118448] Allocate Port Service[0000:00:0b.0:pcie03] [ 36.118489] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 36.118501] assign_interrupt_mode Found MSI capability [ 36.118502] Allocate Port Service[0000:00:0c.0:pcie00] [ 36.118527] Allocate Port Service[0000:00:0c.0:pcie03] [ 36.118567] PCI: Setting latency timer of device 0000:00:0d.0 to 64 [ 36.118578] assign_interrupt_mode Found MSI capability [ 36.118580] Allocate Port Service[0000:00:0d.0:pcie00] [ 36.118608] Allocate Port Service[0000:00:0d.0:pcie03] [ 36.118654] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 36.118665] assign_interrupt_mode Found MSI capability [ 36.118666] Allocate Port Service[0000:00:0e.0:pcie00] [ 36.118693] Allocate Port Service[0000:00:0e.0:pcie03] [ 36.118801] isapnp: Scanning for PnP cards... [ 36.470808] isapnp: No Plug & Play device found [ 36.489025] Real Time Clock Driver v1.12ac [ 36.489130] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 36.489236] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 36.489647] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 36.490256] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 36.490262] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 36.490265] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 36.490427] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 36.493048] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 36.493052] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 36.493162] mice: PS/2 mouse device common for all mice [ 36.493564] EISA: Probing bus 0 at eisa.0 [ 36.493574] Cannot allocate resource for EISA slot 4 [ 36.493578] Cannot allocate resource for EISA slot 6 [ 36.493580] Cannot allocate resource for EISA slot 7 [ 36.493581] Cannot allocate resource for EISA slot 8 [ 36.493582] EISA: Detected 0 cards. [ 36.493656] TCP cubic registered [ 36.493665] NET: Registered protocol family 1 [ 36.493693] Starting balanced_irq [ 36.493711] Using IPI No-Shortcut mode [ 36.493844] Magic number: 11:10:568 [ 36.493923] hash matches device ptyb0 [ 36.494015] hash matches device PNP0C0F:15 [ 36.494320] Freeing unused kernel memory: 336k freed [ 36.514866] input: AT Translated Set 2 keyboard as /class/input/input0 [ 36.680986] ACPI: Fan [FAN] (on) [ 36.686385] ACPI: Thermal Zone [THRM] (22 C) [ 37.228761] usbcore: registered new interface driver usbfs [ 37.228783] usbcore: registered new interface driver hub [ 37.229472] usbcore: registered new device driver usb [ 37.248193] SCSI subsystem initialized [ 37.325760] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61. [ 37.326092] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 [ 37.326100] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 16 [ 37.326107] PCI: Setting latency timer of device 0000:00:0a.0 to 64 [ 37.328332] Floppy drive(s): fd0 is 1.44M [ 37.329862] libata version 3.00 loaded. [ 37.347439] FDC 0 is a post-1991 82077 [ 37.349120] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver [ 37.843618] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:19:db:6d:3f:1b [ 37.843623] forcedeth 0000:00:0a.0: highdma csum timirq gbit lnktim desc-v3 [ 37.843731] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 [ 37.843752] NFORCE-CK804: chipset revision 243 [ 37.843754] NFORCE-CK804: not 100% native mode: will probe irqs later [ 37.843757] NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround. [ 37.843760] NFORCE-CK804: 0000:00:06.0 (rev f3) UDMA133 controller [ 37.843765] ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA [ 37.843772] ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA [ 37.843778] Probing IDE interface ide0... [ 38.130993] hdb: WDC WD2500JB-55REA0, ATA DISK drive [ 38.578454] hda: IDE-DVD ROM 16x, ATAPI CD/DVD-ROM drive [ 38.578460] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 38.578556] hda: selected mode 0x42 [ 38.578840] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 38.578884] hdb: selected mode 0x45 [ 38.578986] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 38.602277] Probing IDE interface ide1... [ 38.890079] hdd: Maxtor 6Y120P0, ATA DISK drive [ 39.225676] hdc: WDC WD2000BB-22GUC0, ATA DISK drive [ 39.225682] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 39.226898] hdc: selected mode 0x45 [ 39.228135] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 39.228224] hdd: selected mode 0x46 [ 39.228361] ide1 at 0x170-0x177,0x376 on irq 15 [ 39.241535] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 [ 39.241542] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 17 [ 39.241553] PCI: Setting latency timer of device 0000:00:02.1 to 64 [ 39.241555] ehci_hcd 0000:00:02.1: EHCI Host Controller [ 39.241754] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 [ 39.241781] ehci_hcd 0000:00:02.1: debug port 1 [ 39.241783] PCI: cache line size of 64 is not supported by device 0000:00:02.1 [ 39.241789] ehci_hcd 0000:00:02.1: irq 17, io mem 0xfe02e000 [ 39.241794] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 39.241876] usb usb1: configuration #1 chosen from 1 choice [ 39.241896] hub 1-0:1.0: USB hub found [ 39.241902] hub 1-0:1.0: 10 ports detected [ 39.346310] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21 [ 39.346319] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 21 (level, low) -> IRQ 18 [ 39.346331] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 39.346334] ohci_hcd 0000:00:02.0: OHCI Host Controller [ 39.346365] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 [ 39.346380] ohci_hcd 0000:00:02.0: irq 18, io mem 0xfe02f000 [ 39.404789] usb usb2: configuration #1 chosen from 1 choice [ 39.404811] hub 2-0:1.0: USB hub found [ 39.404820] hub 2-0:1.0: 10 ports detected [ 39.509801] sata_nv 0000:00:07.0: version 3.5 [ 39.510182] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20 [ 39.510191] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 20 (level, low) -> IRQ 19 [ 39.510194] sata_nv 0000:00:07.0: Using ADMA mode [ 39.510246] PCI: Setting latency timer of device 0000:00:07.0 to 64 [ 39.511294] scsi0 : sata_nv [ 39.511354] scsi1 : sata_nv [ 39.511412] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xcc00 irq 19 [ 39.511414] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xcc08 irq 19 [ 39.526569] hdb: max request size: 512KiB [ 39.537686] hdb: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100) [ 39.537764] hdb: cache flushes supported [ 39.537795] hdb: hdb1 [ 39.546333] hdc: max request size: 512KiB [ 39.547593] hdc: 390721968 sectors (200049 MB) w/2048KiB Cache, CHS=24321/255/63, UDMA(100) [ 39.547775] hda: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(33) [ 39.547779] Uniform CD-ROM driver Revision: 3.20 [ 39.549304] hdc: cache flushes supported [ 39.549330] hdc: hdc1 hdc2 [ 39.581676] hdd: max request size: 128KiB [ 39.581890] hdd: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133) [ 39.582005] hdd: cache flushes supported [ 39.582023] hdd:<6>usb 1-1: new high speed USB device using ehci_hcd and address 2 [ 39.586750] hdd1 [ 39.719845] usb 1-1: configuration #1 chosen from 1 choice [ 39.779516] kjournald starting. Commit interval 5 seconds [ 39.779525] EXT3-fs: mounted filesystem with ordered data mode. [ 39.976714] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 39.986136] ata1.00: ATA-7: Maxtor 7H500F0, HA431DN0, max UDMA/133 [ 39.986139] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 40.002773] ata1.00: configured for UDMA/133 [ 40.312304] ata2: SATA link down (SStatus 0 SControl 300) [ 40.312396] scsi 0:0:0:0: Direct-Access ATA Maxtor 7H500F0 HA43 PQ: 0 ANSI: 5 [ 40.312403] ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 [ 40.312812] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23 [ 40.312815] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 23 (level, low) -> IRQ 16 [ 40.312819] sata_nv 0000:00:08.0: Using ADMA mode [ 40.312860] PCI: Setting latency timer of device 0000:00:08.0 to 64 [ 40.312947] scsi2 : sata_nv [ 40.312981] scsi3 : sata_nv [ 40.313035] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xb800 irq 16 [ 40.313037] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xb808 irq 16 [ 40.436160] usb 1-7: new high speed USB device using ehci_hcd and address 5 [ 40.629073] usb 1-7: configuration #1 chosen from 1 choice [ 40.779750] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 40.789094] ata3.00: ATA-7: Maxtor 7L250S0, BACE1G20, max UDMA/133 [ 40.789098] ata3.00: 490234752 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 40.805747] ata3.00: configured for UDMA/133 [ 40.931592] usb 2-3: new full speed USB device using ohci_hcd and address 2 [ 41.115339] ata4: SATA link down (SStatus 0 SControl 300) [ 41.115428] scsi 2:0:0:0: Direct-Access ATA Maxtor 7L250S0 BACE PQ: 0 ANSI: 5 [ 41.115435] ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 [ 41.146506] usb 2-3: configuration #1 chosen from 1 choice [ 41.450936] usb 2-6: new full speed USB device using ohci_hcd and address 3 [ 41.668920] usb 2-6: configuration #1 chosen from 1 choice [ 46.414433] sysfs: duplicate filename 'eth1' can not be created [ 46.414438] WARNING: at fs/sysfs/dir.c:424 sysfs_add_one() [ 46.414445] [<c01ba80f>] sysfs_add_one+0x9f/0xe0 [ 46.414456] [<c01bb5c6>] sysfs_create_link+0x86/0x110 [ 46.414462] [<c025608a>] device_rename+0x17a/0x1e0 [ 46.414467] [<c0130190>] run_timer_softirq+0x30/0x180 [ 46.414472] [<c0287a60>] dev_change_name+0xb0/0x200 [ 46.414476] [<c0159a62>] filemap_fault+0x1f2/0x400 [ 46.414478] [<c012c895>] __do_softirq+0x75/0xf0 [ 46.414484] [<c027a260>] sock_ioctl+0x0/0x230 [ 46.414487] [<c028809c>] dev_ioctl+0x25c/0x520 [ 46.414489] [<c01646eb>] __do_fault+0x1ab/0x380 [ 46.414494] [<c0165d28>] handle_mm_fault+0xf8/0x610 [ 46.414499] [<c027a260>] sock_ioctl+0x0/0x230 [ 46.414502] [<c018343b>] do_ioctl+0x2b/0x90 [ 46.414506] [<c01834fc>] vfs_ioctl+0x5c/0x290 [ 46.414510] [<c0183798>] sys_ioctl+0x68/0x80 [ 46.414513] [<c01041de>] sysenter_past_esp+0x5f/0x85 [ 46.414520] ======================= [ 46.414523] net eth1: device_rename: sysfs_create_symlink failed (-17) [ 47.083004] NET: Registered protocol family 10 [ 47.083212] lo: Disabled Privacy Extensions [ 47.631643] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 47.765417] input: PC Speaker as /class/input/input1 [ 47.815304] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 47.827778] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00 [ 47.827792] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40 [ 47.849916] input: Power Button (FF) as /class/input/input2 [ 47.899283] ACPI: Power Button (FF) [PWRF] [ 47.899345] input: Power Button (CM) as /class/input/input3 [ 47.959228] ACPI: Power Button (CM) [PWRB] [ 48.256934] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 48.256947] sd 0:0:0:0: [sda] Write Protect is off [ 48.256950] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 48.256963] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 48.257005] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) [ 48.257011] sd 0:0:0:0: [sda] Write Protect is off [ 48.257013] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 48.257024] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 48.257027] sda: sda1 [ 48.280235] sd 0:0:0:0: [sda] Attached SCSI disk [ 48.280326] sd 2:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) [ 48.280335] sd 2:0:0:0: [sdb] Write Protect is off [ 48.280337] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 48.280349] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 48.280383] sd 2:0:0:0: [sdb] 490234752 512-byte hardware sectors (251000 MB) [ 48.280389] sd 2:0:0:0: [sdb] Write Protect is off [ 48.280390] sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 48.280400] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 48.280402] sdb: sdb1 [ 48.300648] sd 2:0:0:0: [sdb] Attached SCSI disk [ 48.325240] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 48.325265] sd 2:0:0:0: Attached scsi generic sg1 type 0 [ 48.398212] input: ImPS/2 Generic Wheel Mouse as /class/input/input4 [ 48.457082] parport_pc 00:09: reported by Plug and Play ACPI [ 48.457126] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 48.576313] Linux agpgart interface v0.102 [ 48.639692] usbcore: registered new interface driver libusual [ 48.656014] usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005 [ 48.656034] usbcore: registered new interface driver usblp [ 48.767341] Initializing USB Mass Storage driver... [ 48.768347] scsi4 : SCSI emulation for USB Mass Storage devices [ 48.768737] usb-storage: device found at 5 [ 48.768742] usb-storage: waiting for device to settle before scanning [ 48.768573] scsi5 : SCSI emulation for USB Mass Storage devices [ 48.770509] usb-storage: device found at 2 [ 48.770511] usb-storage: waiting for device to settle before scanning [ 48.770195] usbcore: registered new interface driver usb-storage [ 48.770199] USB Mass Storage support registered. [ 48.786595] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22 [ 48.786600] ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 22 (level, low) -> IRQ 17 [ 48.786619] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 49.107097] intel8x0_measure_ac97_clock: measured 54714 usecs [ 49.107100] intel8x0: clocking to 46897 [ 49.274889] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 [ 49.274902] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20 [ 49.274909] PCI: Setting latency timer of device 0000:05:00.0 to 64 [ 49.399917] lp0: using parport0 (interrupt-driven). [ 49.451871] fuse init (API version 7.9) [ 49.516676] Adding 10241428k swap on /dev/hdc2. Priority:-1 extents:1 across:10241428k [ 49.592091] EXT3 FS on hdb1, internal journal [ 50.738122] kjournald starting. Commit interval 5 seconds [ 50.744102] EXT3 FS on hdc1, internal journal [ 50.744109] EXT3-fs: mounted filesystem with ordered data mode. [ 50.756820] kjournald starting. Commit interval 5 seconds [ 50.763926] EXT3 FS on hdd1, internal journal [ 50.763929] EXT3-fs: mounted filesystem with ordered data mode. [ 50.790933] kjournald starting. Commit interval 5 seconds [ 50.800195] EXT3 FS on sdb1, internal journal [ 50.800199] EXT3-fs: mounted filesystem with ordered data mode. [ 52.093818] NET: Registered protocol family 17 [ 53.761445] usb-storage: device scan complete [ 53.763647] scsi 4:0:0:0: CD-ROM MAD DOG MD-16XDVD9 2.FD PQ: 0 ANSI: 0 [ 53.763918] scsi 4:0:0:0: Attached scsi generic sg2 type 5 [ 53.767538] usb-storage: device scan complete [ 53.774534] scsi 5:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 [ 53.781515] scsi 5:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 [ 53.788503] scsi 5:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 [ 53.795713] scsi 5:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 [ 53.807495] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 53.807547] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 53.808907] sd 5:0:0:0: [sdc] Attached SCSI removable disk [ 53.808947] sd 5:0:0:0: Attached scsi generic sg3 type 0 [ 53.825502] sd 5:0:0:1: [sdd] Attached SCSI removable disk [ 53.825540] sd 5:0:0:1: Attached scsi generic sg4 type 0 [ 53.835515] sd 5:0:0:2: [sde] Attached SCSI removable disk [ 53.835551] sd 5:0:0:2: Attached scsi generic sg5 type 0 [ 53.846500] sd 5:0:0:3: [sdf] Attached SCSI removable disk [ 53.846538] sd 5:0:0:3: Attached scsi generic sg6 type 0 [ 57.555625] eth1: no IPv6 routers present - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists