Message-id: <1196253340.2884.1.camel@localhost.localdomain>
Date:	Wed, 28 Nov 2007 13:35:40 +0100
From:	Kjartan Maraas <kmaraas@...adpark.no>
To:	Tejun Heo <htejun@...il.com>
Cc:	Tomas Carnecky <tom@...ervice.com>, Pavel Machek <pavel@....cz>,
	linux-ide@...r.kernel.org,
	linux-kernel <linux-kernel@...r.kernel.org>
Subject: Re: laptop reboots right after hibernation


on., 28.11.2007 kl. 10.09 +0900, skrev Tejun Heo:
> Kjartan Maraas wrote:
> > I get this exact error message on a normal first time boot here. I'm
> > using the latest fedora development kernel which is 2.6.24-rc2-git6
> > based. And I have the latest BIOS from HP IIRC.
> > 
> > This is an HP nc6400 intel based laptop:
> 
> Care to post boot dmesg?  Or does harddisk detection fail because of this?
> 
Here you go. It shows the error two times and then it gets it right and
continues to boot. No other problems arise from this that I can see.

libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 21 (level, low) -> IRQ 22
ahci 0000:00:1f.2: nr_ports (4) and implemented port map (0x1) don't match, using nr_ports
ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 3-1: new full speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@...4785000 port 0xf4785100 irq 220
ata2: SATA max UDMA/133 abar m1024@...4785000 port 0xf4785180 irq 220
ata3: SATA max UDMA/133 abar m1024@...4785000 port 0xf4785200 irq 220
ata4: SATA max UDMA/133 abar m1024@...4785000 port 0xf4785280 irq 220
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 failed (Emask=0x1 Stat=0x51 Err=0x04)
ata1: failed to recover some devices, retrying in 5 secs
input: PS/2 Generic Mouse as /class/input/input3
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd b1/c1:00:00:00:00:a0 failed (Emask=0x1 Stat=0x51 Err=0x04)
ata1.00: ACPI on devcfg failed the second time, disabling (errno=-5)
ata1.00: revalidation failed (errno=1)
ata1: failed to recover some devices, retrying in 5 secs
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 0)
ata3: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 0)
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
insmod used greatest stack depth: 596 bytes left
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds

Cheers
Kjartan


-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists