| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <200712271836.23028.bzolnier@gmail.com>
Date: Thu, 27 Dec 2007 18:36:22 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: linux-kernel@...r.kernel.org
Subject: [PATCH 1/3] amd74xx: remove amd_ide_chips table
* Remove no longer needed assertion from amd74xx_probe().
* Factor out cable detection for AMD7409 to amd7409_cable_detect() and for
chipsets >= AMD7411 to amd7411_cable_detect().
* Use dev->vendor and dev->device instead of amd_config->udma_mask when
selecting cable detection method and checking for broken FIFO support in
init_chipset_amd74xx().
* Remove no longer needed AMD_BAD_FIFO define.
* Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro.
* Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro.
* Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe()
in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask
on Serenade mainboards.
* Remove no longer needed fixups from init_chipset_amd74xx()
and AMD_CHECK_{SWDMA,SERENADE} defines.
* Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(),
also remove incorrect comment while at it.
* Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive().
* Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from
amd_set_drive() instead of using amd_config->udma_mask.
* Move amd_config->base from AMD_* defines to users of these defines and add
0x40 the defined values. Then add amd_offset() inline helper for selecting
offset from 0x40 base (needed for nVidia controllers) and finally use it in
amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead
of amd_config->base.
* Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup
from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips
table.
* Fix init_chipset_amd74xx() comment.
* Bump driver version.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
-305 bytes
drivers/ide/pci/amd74xx.c | 275 ++++++++++++++++++++--------------------------
1 file changed, 124 insertions(+), 151 deletions(-)
Index: b/drivers/ide/pci/amd74xx.c
===================================================================
--- a/drivers/ide/pci/amd74xx.c
+++ b/drivers/ide/pci/amd74xx.c
@@ -1,5 +1,5 @@
/*
- * Version 2.24
+ * Version 2.25
*
* AMD 755/756/766/8111 and nVidia nForce/2/2s/3/3s/CK804/MCP04
* IDE driver for Linux.
@@ -28,81 +28,46 @@
#include "ide-timing.h"
-#define AMD_IDE_CONFIG (0x01 + amd_config->base)
-#define AMD_CABLE_DETECT (0x02 + amd_config->base)
-#define AMD_DRIVE_TIMING (0x08 + amd_config->base)
-#define AMD_8BIT_TIMING (0x0e + amd_config->base)
-#define AMD_ADDRESS_SETUP (0x0c + amd_config->base)
-#define AMD_UDMA_TIMING (0x10 + amd_config->base)
-
-#define AMD_CHECK_SWDMA 0x08
-#define AMD_BAD_SWDMA 0x10
-#define AMD_BAD_FIFO 0x20
-#define AMD_CHECK_SERENADE 0x40
-
-/*
- * AMD SouthBridge chips.
- */
-
-static struct amd_ide_chip {
- unsigned short id;
- u8 base;
- u8 udma_mask;
- u8 flags;
-} amd_ide_chips[] = {
- { PCI_DEVICE_ID_AMD_COBRA_7401, 0x40, ATA_UDMA2, AMD_BAD_SWDMA },
- { PCI_DEVICE_ID_AMD_VIPER_7409, 0x40, ATA_UDMA4, AMD_CHECK_SWDMA },
- { PCI_DEVICE_ID_AMD_VIPER_7411, 0x40, ATA_UDMA5, AMD_BAD_FIFO },
- { PCI_DEVICE_ID_AMD_OPUS_7441, 0x40, ATA_UDMA5, },
- { PCI_DEVICE_ID_AMD_8111_IDE, 0x40, ATA_UDMA6, AMD_CHECK_SERENADE },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_IDE, 0x50, ATA_UDMA5, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE2_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE2S_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE2S_SATA, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE3_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE3S_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE3S_SATA2, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_CK804_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP04_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP51_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP55_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP61_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP65_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP67_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP73_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_NVIDIA_NFORCE_MCP77_IDE, 0x50, ATA_UDMA6, },
- { PCI_DEVICE_ID_AMD_CS5536_IDE, 0x40, ATA_UDMA5, },
- { 0 }
+enum {
+ AMD_IDE_CONFIG = 0x41,
+ AMD_CABLE_DETECT = 0x42,
+ AMD_DRIVE_TIMING = 0x48,
+ AMD_8BIT_TIMING = 0x4e,
+ AMD_ADDRESS_SETUP = 0x4c,
+ AMD_UDMA_TIMING = 0x50,
};
-static struct amd_ide_chip *amd_config;
-static const struct ide_port_info *amd_chipset;
static unsigned int amd_80w;
static unsigned int amd_clock;
static char *amd_dma[] = { "16", "25", "33", "44", "66", "100", "133" };
static unsigned char amd_cyc2udma[] = { 6, 6, 5, 4, 0, 1, 1, 2, 2, 3, 3, 3, 3, 3, 3, 7 };
+static inline u8 amd_offset(struct pci_dev *dev)
+{
+ return (dev->vendor == PCI_VENDOR_ID_NVIDIA) ? 0x10 : 0;
+}
+
/*
* amd_set_speed() writes timing values to the chipset registers
*/
-static void amd_set_speed(struct pci_dev *dev, unsigned char dn, struct ide_timing *timing)
+static void amd_set_speed(struct pci_dev *dev, u8 dn, u8 udma_mask,
+ struct ide_timing *timing)
{
- unsigned char t;
+ u8 t = 0, offset = amd_offset(dev);
- pci_read_config_byte(dev, AMD_ADDRESS_SETUP, &t);
+ pci_read_config_byte(dev, AMD_ADDRESS_SETUP + offset, &t);
t = (t & ~(3 << ((3 - dn) << 1))) | ((FIT(timing->setup, 1, 4) - 1) << ((3 - dn) << 1));
- pci_write_config_byte(dev, AMD_ADDRESS_SETUP, t);
+ pci_write_config_byte(dev, AMD_ADDRESS_SETUP + offset, t);
- pci_write_config_byte(dev, AMD_8BIT_TIMING + (1 - (dn >> 1)),
+ pci_write_config_byte(dev, AMD_8BIT_TIMING + offset + (1 - (dn >> 1)),
((FIT(timing->act8b, 1, 16) - 1) << 4) | (FIT(timing->rec8b, 1, 16) - 1));
- pci_write_config_byte(dev, AMD_DRIVE_TIMING + (3 - dn),
+ pci_write_config_byte(dev, AMD_DRIVE_TIMING + offset + (3 - dn),
((FIT(timing->active, 1, 16) - 1) << 4) | (FIT(timing->recover, 1, 16) - 1));
- switch (amd_config->udma_mask) {
+ switch (udma_mask) {
case ATA_UDMA2: t = timing->udma ? (0xc0 | (FIT(timing->udma, 2, 5) - 2)) : 0x03; break;
case ATA_UDMA4: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 2, 10)]) : 0x03; break;
case ATA_UDMA5: t = timing->udma ? (0xc0 | amd_cyc2udma[FIT(timing->udma, 1, 10)]) : 0x03; break;
@@ -110,7 +75,7 @@ static void amd_set_speed(struct pci_dev
default: return;
}
- pci_write_config_byte(dev, AMD_UDMA_TIMING + (3 - dn), t);
+ pci_write_config_byte(dev, AMD_UDMA_TIMING + offset + (3 - dn), t);
}
/*
@@ -120,12 +85,14 @@ static void amd_set_speed(struct pci_dev
static void amd_set_drive(ide_drive_t *drive, const u8 speed)
{
- ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
+ ide_hwif_t *hwif = drive->hwif;
+ ide_drive_t *peer = hwif->drives + (~drive->dn & 1);
struct ide_timing t, p;
int T, UT;
+ u8 udma_mask = hwif->ultra_mask;
T = 1000000000 / amd_clock;
- UT = (amd_config->udma_mask == ATA_UDMA2) ? T : (T / 2);
+ UT = (udma_mask == ATA_UDMA2) ? T : (T / 2);
ide_timing_compute(drive, speed, &t, T, UT);
@@ -137,7 +104,7 @@ static void amd_set_drive(ide_drive_t *d
if (speed == XFER_UDMA_5 && amd_clock <= 33333) t.udma = 1;
if (speed == XFER_UDMA_6 && amd_clock <= 33333) t.udma = 15;
- amd_set_speed(HWIF(drive)->pci_dev, drive->dn, &t);
+ amd_set_speed(hwif->pci_dev, drive->dn, udma_mask, &t);
}
/*
@@ -149,67 +116,68 @@ static void amd_set_pio_mode(ide_drive_t
amd_set_drive(drive, XFER_PIO_0 + pio);
}
-/*
- * The initialization callback. Here we determine the IDE chip type
- * and initialize its drive independent registers.
- */
+static void __devinit amd7409_cable_detect(struct pci_dev *dev,
+ const char *name)
+{
+ /* no host side cable detection */
+ amd_80w = 0x03;
+}
-static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev, const char *name)
+static void __devinit amd7411_cable_detect(struct pci_dev *dev,
+ const char *name)
{
- unsigned char t;
- unsigned int u;
int i;
+ u32 u = 0;
+ u8 t = 0, offset = amd_offset(dev);
+
+ pci_read_config_byte(dev, AMD_CABLE_DETECT + offset, &t);
+ pci_read_config_dword(dev, AMD_UDMA_TIMING + offset, &u);
+ amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0);
+ for (i = 24; i >= 0; i -= 8)
+ if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) {
+ printk(KERN_WARNING "%s: BIOS didn't set cable bits "
+ "correctly. Enabling workaround.\n",
+ name);
+ amd_80w |= (1 << (1 - (i >> 4)));
+ }
+}
/*
- * Check for bad SWDMA.
+ * The initialization callback. Initialize drive independent registers.
*/
- if (amd_config->flags & AMD_CHECK_SWDMA) {
- if (dev->revision <= 7)
- amd_config->flags |= AMD_BAD_SWDMA;
- }
+static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev,
+ const char *name)
+{
+ u8 t = 0, offset = amd_offset(dev);
/*
* Check 80-wire cable presence.
*/
- switch (amd_config->udma_mask) {
-
- case ATA_UDMA6:
- case ATA_UDMA5:
- pci_read_config_byte(dev, AMD_CABLE_DETECT, &t);
- pci_read_config_dword(dev, AMD_UDMA_TIMING, &u);
- amd_80w = ((t & 0x3) ? 1 : 0) | ((t & 0xc) ? 2 : 0);
- for (i = 24; i >= 0; i -= 8)
- if (((u >> i) & 4) && !(amd_80w & (1 << (1 - (i >> 4))))) {
- printk(KERN_WARNING "%s: BIOS didn't set cable bits correctly.
Enabling workaround.\n",
- amd_chipset->name);
- amd_80w |= (1 << (1 - (i >> 4)));
- }
- break;
-
- case ATA_UDMA4:
- /* no host side cable detection */
- amd_80w = 0x03;
- break;
- }
+ if (dev->vendor == PCI_VENDOR_ID_AMD &&
+ dev->device == PCI_DEVICE_ID_AMD_COBRA_7401)
+ ; /* no UDMA > 2 */
+ else if (dev->vendor == PCI_VENDOR_ID_AMD &&
+ dev->device == PCI_DEVICE_ID_AMD_VIPER_7409)
+ amd7409_cable_detect(dev, name);
+ else
+ amd7411_cable_detect(dev, name);
/*
* Take care of prefetch & postwrite.
*/
- pci_read_config_byte(dev, AMD_IDE_CONFIG, &t);
- pci_write_config_byte(dev, AMD_IDE_CONFIG,
- (amd_config->flags & AMD_BAD_FIFO) ? (t & 0x0f) : (t | 0xf0));
-
-/*
- * Take care of incorrectly wired Serenade mainboards.
- */
-
- if ((amd_config->flags & AMD_CHECK_SERENADE) &&
- dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
- dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
- amd_config->udma_mask = ATA_UDMA5;
+ pci_read_config_byte(dev, AMD_IDE_CONFIG + offset, &t);
+ /*
+ * Check for broken FIFO support.
+ */
+ if (dev->vendor == PCI_VENDOR_ID_AMD &&
+ dev->vendor == PCI_DEVICE_ID_AMD_VIPER_7411)
+ t &= 0x0f;
+ else
+ t |= 0xf0;
+ pci_write_config_byte(dev, AMD_IDE_CONFIG + offset, t);
/*
* Determine the system bus clock.
@@ -225,18 +193,10 @@ static unsigned int __devinit init_chips
if (amd_clock < 20000 || amd_clock > 50000) {
printk(KERN_WARNING "%s: User given PCI clock speed impossible (%d), using 33 MHz instead.\n",
- amd_chipset->name, amd_clock);
+ name, amd_clock);
amd_clock = 33333;
}
-/*
- * Print the boot message.
- */
-
- printk(KERN_INFO "%s: %s (rev %02x) UDMA%s controller\n",
- amd_chipset->name, pci_name(dev), dev->revision,
- amd_dma[fls(amd_config->udma_mask) - 1]);
-
return dev->irq;
}
@@ -251,10 +211,6 @@ static void __devinit init_hwif_amd74xx(
if (!hwif->dma_base)
return;
- hwif->ultra_mask = amd_config->udma_mask;
- if (amd_config->flags & AMD_BAD_SWDMA)
- hwif->swdma_mask = 0x00;
-
if (hwif->cbl != ATA_CBL_PATA40_SHORT) {
if ((amd_80w >> hwif->channel) & 1)
hwif->cbl = ATA_CBL_PATA80;
@@ -272,7 +228,7 @@ static void __devinit init_hwif_amd74xx(
IDE_HFLAG_UNMASK_IRQS | \
IDE_HFLAG_BOOTABLE)
-#define DECLARE_AMD_DEV(name_str) \
+#define DECLARE_AMD_DEV(name_str, swdma, udma) \
{ \
.name = name_str, \
.init_chipset = init_chipset_amd74xx, \
@@ -280,11 +236,12 @@ static void __devinit init_hwif_amd74xx(
.enablebits = {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, \
.host_flags = IDE_HFLAGS_AMD, \
.pio_mask = ATA_PIO5, \
- .swdma_mask = ATA_SWDMA2, \
+ .swdma_mask = swdma, \
.mwdma_mask = ATA_MWDMA2, \
+ .udma_mask = udma, \
}
-#define DECLARE_NV_DEV(name_str) \
+#define DECLARE_NV_DEV(name_str, udma) \
{ \
.name = name_str, \
.init_chipset = init_chipset_amd74xx, \
@@ -294,45 +251,61 @@ static void __devinit init_hwif_amd74xx(
.pio_mask = ATA_PIO5, \
.swdma_mask = ATA_SWDMA2, \
.mwdma_mask = ATA_MWDMA2, \
+ .udma_mask = udma, \
}
static const struct ide_port_info amd74xx_chipsets[] __devinitdata = {
- /* 0 */ DECLARE_AMD_DEV("AMD7401"),
- /* 1 */ DECLARE_AMD_DEV("AMD7409"),
- /* 2 */ DECLARE_AMD_DEV("AMD7411"),
- /* 3 */ DECLARE_AMD_DEV("AMD7441"),
- /* 4 */ DECLARE_AMD_DEV("AMD8111"),
-
- /* 5 */ DECLARE_NV_DEV("NFORCE"),
- /* 6 */ DECLARE_NV_DEV("NFORCE2"),
- /* 7 */ DECLARE_NV_DEV("NFORCE2-U400R"),
- /* 8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA"),
- /* 9 */ DECLARE_NV_DEV("NFORCE3-150"),
- /* 10 */ DECLARE_NV_DEV("NFORCE3-250"),
- /* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA"),
- /* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2"),
- /* 13 */ DECLARE_NV_DEV("NFORCE-CK804"),
- /* 14 */ DECLARE_NV_DEV("NFORCE-MCP04"),
- /* 15 */ DECLARE_NV_DEV("NFORCE-MCP51"),
- /* 16 */ DECLARE_NV_DEV("NFORCE-MCP55"),
- /* 17 */ DECLARE_NV_DEV("NFORCE-MCP61"),
- /* 18 */ DECLARE_NV_DEV("NFORCE-MCP65"),
- /* 19 */ DECLARE_NV_DEV("NFORCE-MCP67"),
- /* 20 */ DECLARE_NV_DEV("NFORCE-MCP73"),
- /* 21 */ DECLARE_NV_DEV("NFORCE-MCP77"),
- /* 22 */ DECLARE_AMD_DEV("AMD5536"),
+ /* 0 */ DECLARE_AMD_DEV("AMD7401", 0x00, ATA_UDMA2),
+ /* 1 */ DECLARE_AMD_DEV("AMD7409", ATA_SWDMA2, ATA_UDMA4),
+ /* 2 */ DECLARE_AMD_DEV("AMD7411", ATA_SWDMA2, ATA_UDMA5),
+ /* 3 */ DECLARE_AMD_DEV("AMD7441", ATA_SWDMA2, ATA_UDMA5),
+ /* 4 */ DECLARE_AMD_DEV("AMD8111", ATA_SWDMA2, ATA_UDMA6),
+
+ /* 5 */ DECLARE_NV_DEV("NFORCE", ATA_UDMA5),
+ /* 6 */ DECLARE_NV_DEV("NFORCE2", ATA_UDMA6),
+ /* 7 */ DECLARE_NV_DEV("NFORCE2-U400R", ATA_UDMA6),
+ /* 8 */ DECLARE_NV_DEV("NFORCE2-U400R-SATA", ATA_UDMA6),
+ /* 9 */ DECLARE_NV_DEV("NFORCE3-150", ATA_UDMA6),
+ /* 10 */ DECLARE_NV_DEV("NFORCE3-250", ATA_UDMA6),
+ /* 11 */ DECLARE_NV_DEV("NFORCE3-250-SATA", ATA_UDMA6),
+ /* 12 */ DECLARE_NV_DEV("NFORCE3-250-SATA2", ATA_UDMA6),
+ /* 13 */ DECLARE_NV_DEV("NFORCE-CK804", ATA_UDMA6),
+ /* 14 */ DECLARE_NV_DEV("NFORCE-MCP04", ATA_UDMA6),
+ /* 15 */ DECLARE_NV_DEV("NFORCE-MCP51", ATA_UDMA6),
+ /* 16 */ DECLARE_NV_DEV("NFORCE-MCP55", ATA_UDMA6),
+ /* 17 */ DECLARE_NV_DEV("NFORCE-MCP61", ATA_UDMA6),
+ /* 18 */ DECLARE_NV_DEV("NFORCE-MCP65", ATA_UDMA6),
+ /* 19 */ DECLARE_NV_DEV("NFORCE-MCP67", ATA_UDMA6),
+ /* 20 */ DECLARE_NV_DEV("NFORCE-MCP73", ATA_UDMA6),
+ /* 21 */ DECLARE_NV_DEV("NFORCE-MCP77", ATA_UDMA6),
+
+ /* 22 */ DECLARE_AMD_DEV("AMD5536", ATA_SWDMA2, ATA_UDMA5),
};
static int __devinit amd74xx_probe(struct pci_dev *dev, const struct pci_device_id *id)
{
- amd_chipset = amd74xx_chipsets + id->driver_data;
- amd_config = amd_ide_chips + id->driver_data;
- if (dev->device != amd_config->id) {
- printk(KERN_ERR "%s: assertion 0x%02x == 0x%02x failed !\n",
- pci_name(dev), dev->device, amd_config->id);
- return -ENODEV;
+ struct ide_port_info d;
+ u8 idx = id->driver_data;
+
+ d = amd74xx_chipsets[idx];
+
+ /*
+ * Check for bad SWDMA and incorrectly wired Serenade mainboards.
+ */
+ if (idx == 1) {
+ if (dev->revision <= 7)
+ d.swdma_mask = 0;
+ } else if (idx == 4) {
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_AMD &&
+ dev->subsystem_device == PCI_DEVICE_ID_AMD_SERENADE)
+ d.udma_mask = ATA_UDMA5;
}
- return ide_setup_pci_device(dev, amd_chipset);
+
+ printk(KERN_INFO "%s: %s (rev %02x) UDMA%s controller\n",
+ d.name, pci_name(dev), dev->revision,
+ amd_dma[fls(d.udma_mask) - 1]);
+
+ return ide_setup_pci_device(dev, &d);
}
static const struct pci_device_id amd74xx_pci_tbl[] = {
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists