[ 0.000000] Linux version 2.6.24.1 (root@highlander) (gcc version 4.2.3 (Debian 4.2.3-1)) #1 SMP Sat Feb 9 11:07:57 CET 2008 [ 0.000000] Command line: root=LABEL=ROOT ro vga=extended console=tty0 console=ttyS0,115200 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 0000000000098000 (usable) [ 0.000000] BIOS-e820: 0000000000098000 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable) [ 0.000000] BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data) [ 0.000000] BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP 000FB400, 0024 (r2 ACPIAM) [ 0.000000] ACPI: XSDT 7FFB0100, 005C (r1 NEC 1000709 MSFT 97) [ 0.000000] ACPI: FACP 7FFB0290, 00F4 (r3 A_M_I_ OEMFACP 1000709 MSFT 97) [ 0.000000] ACPI: DSDT 7FFB05B0, 7A34 (r1 A0578 A0578000 0 INTL 20060113) [ 0.000000] ACPI: FACS 7FFBE000, 0040 [ 0.000000] ACPI: APIC 7FFB0390, 005C (r1 A_M_I_ OEMAPIC 1000709 MSFT 97) [ 0.000000] ACPI: MCFG 7FFB03F0, 003C (r1 A_M_I_ OEMMCFG 1000709 MSFT 97) [ 0.000000] ACPI: SLIC 7FFB0430, 0176 (r1 NEC 1000709 MSFT 97) [ 0.000000] ACPI: OEMB 7FFBE040, 0060 (r1 A_M_I_ AMI_OEM 1000709 MSFT 97) [ 0.000000] ACPI: HPET 7FFB7FF0, 0038 (r1 A_M_I_ OEMHPET 1000709 MSFT 97) [ 0.000000] ACPI: SSDT 7FFB8030, 0248 (r1 A_M_I_ POWERNOW 1 AMD 1) [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 152 [ 0.000000] 0: 256 -> 524208 [ 0.000000] ATI board detected. Disabling timer routing over 8254. [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] Setting APIC routing to flat [ 0.000000] ACPI: HPET id: 0x8300 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7f700000) [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] PERCPU: Allocating 32624 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516128 [ 0.000000] Kernel command line: root=LABEL=ROOT ro vga=extended console=tty0 console=ttyS0,115200 [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Extended CMOS year: 2000 [ 0.000000] TSC calibrated against HPET [ 64.698527] Marking TSC unstable due to TSCs unsynchronized [ 64.698529] time.c: Detected 2405.448 MHz processor. [ 64.717798] Console: colour VGA+ 80x50 [ 64.717801] console [tty0] enabled [ 64.722885] console [ttyS0] enabled [ 65.067150] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 65.075705] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 65.083276] Checking aperture... [ 65.086596] CPU 0: aperture @ fede000000 size 32 MB [ 65.091565] Aperture too small (32 MB) [ 65.104495] No AGP bridge found [ 65.123646] Memory: 2057172k/2096832k available (1727k kernel code, 38664k reserved, 832k data, 208k init) [ 65.133447] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1 [ 65.200682] Calibrating delay using timer specific routine.. 4813.71 BogoMIPS (lpj=2406857) [ 65.209255] Mount-cache hash table entries: 256 [ 65.213953] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 65.221183] CPU: L2 Cache: 512K (64 bytes/line) [ 65.225804] CPU: Physical Processor ID: 0 [ 65.229901] CPU: Processor Core ID: 0 [ 65.233673] SMP alternatives: switching to UP code [ 65.240501] ACPI: Core revision 20070126 [ 65.257607] Using local APIC timer interrupts. [ 65.303873] Detected 12.528 MHz APIC timer. [ 65.308504] SMP alternatives: switching to SMP code [ 65.313735] Booting processor 1/2 APIC 0x1 [ 65.328391] Initializing CPU#1 [ 65.388759] Calibrating delay using timer specific routine.. 4810.82 BogoMIPS (lpj=2405413) [ 65.388765] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 65.388766] CPU: L2 Cache: 512K (64 bytes/line) [ 65.388768] CPU: Physical Processor ID: 0 [ 65.388770] CPU: Processor Core ID: 1 [ 65.388833] AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 02 [ 65.388438] Brought up 2 CPUs [ 65.429529] net_namespace: 120 bytes [ 65.434696] NET: Registered protocol family 16 [ 65.439321] ACPI: bus type pci registered [ 65.443482] PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved [ 65.450006] PCI: Not using MMCONFIG. [ 65.453666] PCI: Using configuration type 1 [ 65.465629] ACPI: Interpreter enabled [ 65.469380] ACPI: (supports S0 S5) [ 65.473018] ACPI: Using IOAPIC for interrupt routing [ 65.478330] Error attaching device data [ 65.482257] Error attaching device data [ 65.493960] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 65.519948] PCI: Transparent bridge - 0000:00:14.4 [ 65.543144] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.552382] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.563083] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.572305] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.581538] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.590788] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled. [ 65.597553] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.606785] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. [ 65.615977] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 0E, should be 05 [20070126] [ 65.627180] Linux Plug and Play Support v0.97 (c) Adam Belay [ 65.632940] pnp: PnP ACPI init [ 65.636085] ACPI: bus type pnp registered [ 65.643944] pnp: PnP ACPI: found 15 devices [ 65.648223] ACPI: ACPI bus type pnp unregistered [ 65.653012] PCI: Using ACPI for IRQ routing [ 65.657285] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 65.669853] DMAR:No DMAR devices found [ 65.673842] Time: hpet clocksource has been installed. [ 65.680913] system 00:06: ioport range 0x4d0-0x4d1 has been reserved [ 65.688638] system 00:06: ioport range 0x40b-0x40b has been reserved [ 65.695080] system 00:06: ioport range 0x4d6-0x4d6 has been reserved [ 65.701527] system 00:06: ioport range 0xc00-0xc01 has been reserved [ 65.707973] system 00:06: ioport range 0xc14-0xc14 has been reserved [ 65.714420] system 00:06: ioport range 0xc50-0xc51 has been reserved [ 65.720865] system 00:06: ioport range 0xc52-0xc52 has been reserved [ 65.727312] system 00:06: ioport range 0xc6c-0xc6c has been reserved [ 65.733758] system 00:06: ioport range 0xc6f-0xc6f has been reserved [ 65.740205] system 00:06: ioport range 0xcd0-0xcd1 has been reserved [ 65.746652] system 00:06: ioport range 0xcd2-0xcd3 has been reserved [ 65.754353] system 00:06: ioport range 0xcd4-0xcd5 has been reserved [ 65.760800] system 00:06: ioport range 0xcd6-0xcd7 has been reserved [ 65.767247] system 00:06: ioport range 0xcd8-0xcdf has been reserved [ 65.773692] system 00:06: ioport range 0x800-0x89f has been reserved [ 65.780138] system 00:06: ioport range 0xb10-0xb1f has been reserved [ 65.786585] system 00:06: ioport range 0x900-0x90f has been reserved [ 65.793033] system 00:06: ioport range 0x910-0x91f has been reserved [ 65.799475] system 00:06: ioport range 0xfe00-0xfefe has been reserved [ 65.806096] system 00:06: iomem range 0xffb80000-0xffbfffff could not be reserved [ 65.813700] system 00:06: iomem range 0xfff00000-0xffffffff could not be reserved [ 65.822524] system 00:06: iomem range 0xff600000-0xff60ffff has been reserved [ 65.829759] system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved [ 65.836992] system 00:09: iomem range 0xfee00000-0xfee00fff could not be reserved [ 65.844603] system 00:0b: ioport range 0xe00-0xe0f has been reserved [ 65.851047] system 00:0b: ioport range 0xe80-0xe8f has been reserved [ 65.857492] system 00:0b: ioport range 0xf40-0xf4f has been reserved [ 65.863942] system 00:0b: ioport range 0xa30-0xa3f has been reserved [ 65.870390] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved [ 65.877617] system 00:0d: iomem range 0xf0000000-0xf08fffff has been reserved [ 65.886130] system 00:0e: iomem range 0x0-0x9ffff could not be reserved [ 65.892845] system 00:0e: iomem range 0xc0000-0xcffff has been reserved [ 65.899554] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved [ 65.906608] system 00:0e: iomem range 0x100000-0x7fffffff could not be reserved [ 65.914035] system 00:0e: iomem range 0x0-0x0 could not be reserved [ 65.920687] PCI: Bridge: 0000:00:04.0 [ 65.924440] IO window: c000-cfff [ 65.927933] MEM window: fae00000-faefffff [ 65.932210] PREFETCH window: disabled. [ 65.936224] PCI: Bridge: 0000:00:05.0 [ 65.939977] IO window: d000-dfff [ 65.944741] MEM window: faf00000-faffffff [ 65.949014] PREFETCH window: disabled. [ 65.953030] PCI: Bridge: 0000:00:14.4 [ 65.956786] IO window: e000-efff [ 65.960280] MEM window: fb000000-fbffffff [ 65.964557] PREFETCH window: f9800000-f9ffffff [ 65.969289] NET: Registered protocol family 2 [ 65.983447] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 65.991146] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 66.000367] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 66.008808] TCP: Hash tables configured (established 262144 bind 65536) [ 66.015522] TCP reno registered [ 66.021450] checking if image is initramfs... it is [ 66.222261] Freeing initrd memory: 3541k freed [ 66.229213] audit: initializing netlink socket (disabled) [ 66.234715] audit(1202556795.894:1): initialized [ 66.241291] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 66.248835] io scheduler noop registered [ 66.252872] io scheduler deadline registered (default) [ 66.374221] assign_interrupt_mode Found MSI capability [ 66.379547] assign_interrupt_mode Found MSI capability [ 66.406794] Real Time Clock Driver v1.12ac [ 66.411021] Linux agpgart interface v0.102 [ 66.415227] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled [ 66.423300] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 66.429858] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 66.436053] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize [ 66.443722] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 66.450000] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 66.459857] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 66.464968] mice: PS/2 mouse device common for all mice [ 66.470318] cpuidle: using governor ladder [ 66.474511] cpuidle: using governor menu [ 66.478550] TCP cubic registered [ 66.481981] BIOS EDD facility v0.16 2004-Jun-25, 6 devices found [ 66.488239] Freeing unused kernel memory: 208k freed Loading, please wait... ^[^[[ 66.513140] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 Begin: Loading essential drivers... ... [ 66.575266] NET: Registered protocol family 1 Done. Begin: Running /scripts/init-premount ... [ 66.631328] ACPI: duty_cycle spans bit 4 [ 66.772225] SCSI subsystem initialized [ 66.776251] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI [ 66.783020] Copyright (c) 1999-2006 Intel Corporation. [ 66.788456] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 66.844296] e1000: 0000:01:00.0: e1000_check_options: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 66.856474] e1000: 0000:01:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x1) 00:1b:21:04:f5:02 [ 66.891985] Floppy drive(s): fd0 is 1.44M [ 66.898775] usbcore: registered new interface driver usbfs [ 66.904582] usbcore: registered new interface driver hub [ 66.910971] FDC 0 is a post-1991 82077 [ 66.915627] usbcore: registered new device driver usb [ 66.928261] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 66.935081] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 66.943103] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit [ 66.950374] ahci 0000:00:12.0: controller can't do PMP, turning off CAP_PMP [ 67.307246] udev: renamed network interface eth0 to eth1 [ 67.956470] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 67.964996] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio slum part [ 67.972820] scsi0 : ahci [ 67.975699] scsi1 : ahci [ 67.978445] scsi2 : ahci [ 67.981178] scsi3 : ahci [ 67.983949] ata1: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd00 irq 509 [ 67.991825] ata2: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffd80 irq 509 [ 67.999729] ata3: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe00 irq 509 [ 68.007619] ata4: SATA max UDMA/133 abar m1024@0xfadffc00 port 0xfadffe80 irq 509 [ 68.470669] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 98.431945] ata1.00: qc timeout (cmd 0xec) [ 98.454907] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 98.461296] ata1: failed to recover some devices, retrying in 5 secs [ 103.916773] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 133.878045] ata1.00: qc timeout (cmd 0xec) [ 133.882371] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 133.888797] ata1: failed to recover some devices, retrying in 5 secs [ 139.343901] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 169.305174] ata1.00: qc timeout (cmd 0xec) [ 169.309534] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 169.315926] ata1: failed to recover some devices, retrying in 5 secs [ 174.771030] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 175.232784] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 205.194064] ata2.00: qc timeout (cmd 0xec) [ 205.198424] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 205.204834] ata2: failed to recover some devices, retrying in 5 secs [ 210.659913] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 240.621188] ata2.00: qc timeout (cmd 0xec) [ 240.625543] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 240.631935] ata2: failed to recover some devices, retrying in 5 secs [ 246.087042] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Begin: Loading MD modules ... [ 246.499384] xor: automatically using best checksumming function: generic_sse [ 246.511385] generic_sse: 7332.000 MB/sec [ 246.515867] xor: using function: generic_sse (7332.000 MB/sec) [ 246.522249] async_tx: api initialized (sync-only) [ 246.547341] raid6: int64x1 2187 MB/s [ 246.567319] raid6: int64x2 2863 MB/s [ 246.587285] raid6: int64x4 2679 MB/s [ 246.607266] raid6: int64x8 2359 MB/s [ 246.628217] raid6: sse2x1 3417 MB/s [ 246.648189] raid6: sse2x2 4453 MB/s [ 246.668158] raid6: sse2x4 4605 MB/s [ 246.672126] raid6: using algorithm sse2x4 (4605 MB/s) [ 246.677478] md: raid6 personality registered for level 6 [ 246.683066] md: raid5 personality registered for level 5 [ 246.688675] md: raid4 personality registered for level 4 Success: loaded module raid456. Done. Begin: Assembling all MD arrays ... mdadm: No devices listed in conf file were found. Failure: failed to assemble all arrays. Done. Begin: Executing udevtrigger again ... Done. Done. Begin: Waiting for root file system... ... [ 276.048325] ata2.00: qc timeout (cmd 0xec) [ 276.052689] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 276.059068] ata2: failed to recover some devices, retrying in 5 secs [ 281.514182] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 281.975740] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 311.936762] ata3.00: qc timeout (cmd 0xec) [ 311.941123] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 311.947544] ata3: failed to recover some devices, retrying in 5 secs [ 317.402620] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 347.363902] ata3.00: qc timeout (cmd 0xec) [ 347.368261] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 347.374662] ata3: failed to recover some devices, retrying in 5 secs [ 352.829756] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 382.791027] ata3.00: qc timeout (cmd 0xec) [ 382.795389] ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 382.801766] ata3: failed to recover some devices, retrying in 5 secs [ 388.256887] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 388.718190] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 418.679474] ata4.00: qc timeout (cmd 0xec) [ 418.683838] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 418.690243] ata4: failed to recover some devices, retrying in 5 secs [ 424.145329] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Done. ALERT! /dev/disk/by-label/ROOT does not exist. Dropping to a shell! Check your root= boot argument (cat /proc/cmdline) Check for missing modules (cat /proc/modules), or device files (ls /dev) BusyBox v1.1.3 (Debian 1:1.1.3-5) Built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off (initramfs) [ 454.106607] ata4.00: qc timeout (cmd 0xec) [ 454.110965] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 454.117416] ata4: failed to recover some devices, retrying in 5 secs [ 459.572452] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 489.538076] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 489.544474] ata4: failed to recover some devices, retrying in 5 secs [ 494.999579] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 495.005723] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17 After pressing Ctrl+d: (initramfs) [ 496.012632] ahci 0000:02:00.0: AHCI 0001.0000 32 slots 1 ports 3 Gbps 0x1 impl SATA mode [ 496.021143] ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part [ 496.028696] scsi4 : ahci [ 496.031469] ata5: SATA max UDMA/133 abar m8192@0xfaffe000 port 0xfaffe100 irq 17 [ 496.343573] ata5: SATA link down (SStatus 0 SControl 300) [ 496.349201] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16 [ 496.357258] scsi5 : pata_atiixp [ 496.361114] scsi6 : pata_atiixp [ 496.365577] ata6: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14 [ 496.372877] ata7: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15 [ 496.553906] ata6.00: ATA-6: IC35L120AVV207-0, V24OA66A, max UDMA/100 [ 496.560570] ata6.00: 241254720 sectors, multi 16: LBA48 [ 496.575833] ata6.00: configured for UDMA/100 [ 496.730650] scsi 5:0:0:0: Direct-Access ATA IC35L120AVV207-0 V24O PQ: 0 ANSI: 5 [ 496.739714] ACPI: PCI Interrupt 0000:03:04.0[A] -> <6>ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19 [ 496.751453] GSI 23 (level, low) -> IRQ 23 [ 496.751051] ehci_hcd 0000:00:13.5: EHCI Host Controller [ 496.751228] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1 [ 496.751292] ehci_hcd 0000:00:13.5: debug port 1 [ 496.751304] ehci_hcd 0000:00:13.5: irq 19, io mem 0xfadff800 [ 496.779858] skge 1.13 addr 0xfbff4000 irq 23 chip Yukon-Lite rev 9 [ 496.779521] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 496.779620] usb usb1: configuration #1 chosen from 1 choice [ 496.779638] hub 1-0:1.0: USB hub found [ 496.779645] hub 1-0:1.0: 10 ports detected [ 496.808602] skge eth0: addr 00:1b:fc:68:3c:19 [ 496.812824] Driver 'sd' needs updating - please use bus_type methods [ 496.819580] sd 5:0:0:0: [sda] 241254720 512-byte hardware sectors (123522 MB) [ 496.827071] sd 5:0:0:0: [sda] Write Protect is off [ 496.832158] sd 5:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 496.841697] sd 5:0:0:0: [sda] 241254720 512-byte hardware sectors (123522 MB) [ 496.849236] sd 5:0:0:0: [sda] Write Protect is off [ 496.854331] sd 5:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 496.863837] sda:<6>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 496.886372] ohci_hcd 0000:00:13.0: OHCI Host Controller [ 496.891939] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 [ 496.894907] sda1 sda2 < sda5<6>ohci_hcd 0000:00:13.0: irq 16, io mem 0xfadfe000 [ 496.908266] sda6 sda7 sda8 > [ 496.934106] sd 5:0:0:0: [sda] Attached SCSI disk [ 496.963310] usb usb2: configuration #1 chosen from 1 choice [ 496.969160] hub 2-0:1.0: USB hub found [ 496.973181] hub 2-0:1.0: 2 ports detected [ 497.078118] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17 [ 497.086121] ohci_hcd 0000:00:13.1: OHCI Host Controller [ 497.091695] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 [ 497.099462] ohci_hcd 0000:00:13.1: irq 17, io mem 0xfadfd000 [ 497.160009] usb usb3: configuration #1 chosen from 1 choice [ 497.165872] hub 3-0:1.0: USB hub found [ 497.169888] hub 3-0:1.0: 2 ports detected [ 497.274808] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 497.282831] ohci_hcd 0000:00:13.2: OHCI Host Controller [ 497.288412] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4 [ 497.296219] ohci_hcd 0000:00:13.2: irq 18, io mem 0xfadfc000 [ 497.356703] usb usb4: configuration #1 chosen from 1 choice [ 497.362612] hub 4-0:1.0: USB hub found [ 497.366595] hub 4-0:1.0: 2 ports detected [ 497.471530] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17 [ 497.479528] ohci_hcd 0000:00:13.3: OHCI Host Controller [ 497.485119] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5 [ 497.492927] ohci_hcd 0000:00:13.3: irq 17, io mem 0xfadf7000 [ 497.554399] usb usb5: configuration #1 chosen from 1 choice [ 497.560310] hub 5-0:1.0: USB hub found [ 497.564309] hub 5-0:1.0: 2 ports detected [ 497.669207] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18 [ 497.677188] ohci_hcd 0000:00:13.4: OHCI Host Controller [ 497.682736] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6 [ 497.690554] ohci_hcd 0000:00:13.4: irq 18, io mem 0xfadf6000 [ 497.751118] usb usb6: configuration #1 chosen from 1 choice [ 497.775596] hub 6-0:1.0: USB hub found [ 497.779546] hub 6-0:1.0: 2 ports detected (initramfs) Begin: Running /scripts/local-premount ... Done. [ 519.925022] kjournald starting. Commit interval 5 seconds Begin: Running /[ 519.925472] EXT3-fs: mounted filesystem with ordered data mode. scripts/local-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. Mount failed for selinuxfs on /selinux: No such file or directory INIT: version 2.86 booting /etc/rcS.d/S00clear_glcd: line 3: /usr/local/bin/showtext: No such file or directory Setting hostname to 'hades'...done. * Files under mount point '/lib/init/rw' will be hidden. Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...[ 522.800446] input: Power Button (FF) as /devices/virtual/input/input1 [ 522.812370] ACPI: Power Button (FF) [PWRF] [ 522.816811] input: Power Button (CM) as /devices/virtual/input/input2 [ 522.829340] ACPI: Power Button (CM) [PWRB] [ 522.912153] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 523.277893] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16 [ 523.358550] hda_codec: Unknown model for AD1988, trying auto-probe from BIOS... done. Setting parameters of disc: (none). Setting the system clock. System Clock set to: Sat Feb 9 11:40:56 UTC 2008. Activating swap:swapon on /dev/s[ 524.985605] Unable to find swap-space signature da2 swapon: /dev/sda2: Invalid argument swapon: cannot canonicalize /dev/sdb2: No such file or directory swapon on /dev/sdb2 swapon: cannot stat /dev/sdb2: No such file or directory swapon: cannot canonicalize /dev/sdc2: No such file or directory swapon on /dev/sdc2 swapon: cannot stat /dev/sdc2: No such file or directory swapon: cannot canonicalize /dev/sde7: No such file or directory swapon on /dev/sde7 swapon: cannot stat /dev/sde7: No such file or directory failed! Will now check root file system:fsck 1.40.5 (27-Jan-2008) [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -y -C0 /dev/sda5 e2fsck 1.40.5 (27-Jan-2008) ROOT: clean, 144797/610432 files, 749592/1220932 blocks . [ 525.289726] EXT3 FS on sda5, internal journal Setting the system clock. System Clock set to: Sat Feb 9 11:40:57 UTC 2008. Cleaning up ifupdown.... Loading kernel module ppdev. [ 525.827503] ppdev: user-space parallel port driver Loading kernel module k8temp. Loading kernel module fuse. [ 525.877267] fuse init (API version 7.9) Loading kernel module tun. [ 525.890020] tun: Universal TUN/TAP device driver, 1.6 [ 525.895353] tun: (C) 1999-2004 Max Krasnyansky Loading kernel module i2c-viapro. Loading kernel module eeprom. Loading kernel module k8temp. Loading kernel module w83627hf. FATAL: Error inserting w83627hf (/lib/modules/2.6.24.1/kernel/drivers/hwmon/w83627hf.ko): No such device Loading kernel module powernow-k8. [ 525.944988] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ processors (2 cpu cores) (version 2.20.00) [ 525.957316] powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0xc [ 525.963284] powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xe [ 525.969159] powernow-k8: 2 : fid 0xc (2000 MHz), vid 0x10 [ 525.975119] powernow-k8: 3 : fid 0xa (1800 MHz), vid 0x10 [ 525.981038] powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12 Loading kernel module cpufreq-ondemand. Loading kernel module kqemu. [ 526.267753] md: md0 stopped. Assembling MD array md0...failed (no devices found). Generating udev events for MD arrays...done. Will now check all file systems. fsck 1.40.5 (27-Jan-2008) Checking all file systems. [/sbin/fsck.ext3 (1) -- /files] fsck.ext3 -y -C0 LABEL=FILES fsck.ext3: Unable to resolve 'LABEL=FILES' [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -y -C0 /dev/sda1 e2fsck 1.40.5 (27-Jan-2008) BOOT: clean, 5780/48192 files, 24940/96358 blocks [/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -y -C0 /dev/sda6 e2fsck 1.40.5 (27-Jan-2008) VAR: clean, 6410/611648 files, 191188/1220932 blocks [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -y -C0 /dev/sda8 e2fsck 1.40.5 (27-Jan-2008) HOME: clean, 120009/13615104 files, 9138673/27202053 blocks fsck died with exit status 8 * File system check failed. A log is being saved in /var/log/fsck/checkfs if that location is writable. Please repair the file system manually. * A maintenance shell will now be started. CONTROL-D will terminate this shell and resume system boot. Give root password for maintenance (or type Control-D to continue):