| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <200802171202.27747.linux@rainbow-software.org>
Date: Sun, 17 Feb 2008 12:02:25 +0100
From: Ondrej Zary <linux@...nbow-software.org>
To: Jeff Garzik <jeff@...zik.org>
Cc: netdev@...r.kernel.org,
Linux Kernel <linux-kernel@...r.kernel.org>,
Andrew Morton <akpm@...ux-foundation.org>
Subject: [PATCH] [resend] 3c509: convert to isa_driver and pnp_driver v5
Hello,
this patch converts 3c509 driver to isa_driver and pnp_driver. The result is
that autoloading using udev and hibernation works with ISA PnP cards. It also
adds hibernation support for non-PnP ISA cards.
xcvr module parameter was removed as its value was not used.
Tested using 3 ISA cards in various combinations of PnP and non-PnP modes.
EISA and MCA only compile-tested.
Signed-off-by: Ondrej Zary <linux@...nbow-software.org>
--- linux-2.6.24-orig/drivers/net/3c509.c 2008-01-27 19:48:19.000000000 +0100
+++ linux-2.6.24-pentium/drivers/net/3c509.c 2008-02-10 21:52:04.000000000 +0100
@@ -54,25 +54,24 @@
v1.19a 28Oct2002 Davud Ruggiero <jdr@...falle.com>
- Increase *read_eeprom udelay to workaround oops with 2 cards.
v1.19b 08Nov2002 Marc Zyngier <maz@...d-wind.fr.eu.org>
- - Introduce driver model for EISA cards.
+ - Introduce driver model for EISA cards.
+ v1.20 04Feb2008 Ondrej Zary <linux@...nbow-software.org>
+ - convert to isa_driver and pnp_driver and some cleanups
*/
#define DRV_NAME "3c509"
-#define DRV_VERSION "1.19b"
-#define DRV_RELDATE "08Nov2002"
+#define DRV_VERSION "1.20"
+#define DRV_RELDATE "04Feb2008"
/* A few values that may be tweaked. */
/* Time in jiffies before concluding the transmitter is hung. */
#define TX_TIMEOUT (400*HZ/1000)
-/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
-static int max_interrupt_work = 10;
#include <linux/module.h>
-#ifdef CONFIG_MCA
#include <linux/mca.h>
-#endif
-#include <linux/isapnp.h>
+#include <linux/isa.h>
+#include <linux/pnp.h>
#include <linux/string.h>
#include <linux/interrupt.h>
#include <linux/errno.h>
@@ -97,10 +96,6 @@
static char version[] __initdata = DRV_NAME ".c:" DRV_VERSION " " DRV_RELDATE " becker@...ld.com\n";
-#if defined(CONFIG_PM) && (defined(CONFIG_MCA) || defined(CONFIG_EISA))
-#define EL3_SUSPEND
-#endif
-
#ifdef EL3_DEBUG
static int el3_debug = EL3_DEBUG;
#else
@@ -111,6 +106,7 @@
* a global variable so that the mca/eisa probe routines can increment
* it */
static int el3_cards = 0;
+#define EL3_MAX_CARDS 8
/* To minimize the size of the driver source I only define operating
constants if they are used several times. You'll need the manual
@@ -119,7 +115,7 @@
#define EL3_DATA 0x00
#define EL3_CMD 0x0e
#define EL3_STATUS 0x0e
-#define EEPROM_READ 0x80
+#define EEPROM_READ 0x80
#define EL3_IO_EXTENT 16
@@ -168,23 +164,31 @@
*/
#define SKB_QUEUE_SIZE 64
+enum el3_cardtype { EL3_ISA, EL3_PNP, EL3_MCA, EL3_EISA };
+
struct el3_private {
struct net_device_stats stats;
- struct net_device *next_dev;
spinlock_t lock;
/* skb send-queue */
int head, size;
struct sk_buff *queue[SKB_QUEUE_SIZE];
- enum {
- EL3_MCA,
- EL3_PNP,
- EL3_EISA,
- } type; /* type of device */
- struct device *dev;
+ enum el3_cardtype type;
};
-static int id_port __initdata = 0x110; /* Start with 0x110 to avoid new sound cards.*/
-static struct net_device *el3_root_dev;
+static int id_port;
+static int current_tag;
+static struct net_device *el3_devs[EL3_MAX_CARDS];
+
+/* Parameters that may be passed into the module. */
+static int debug = -1;
+static int irq[] = {-1, -1, -1, -1, -1, -1, -1, -1};
+/* Maximum events (Rx packets, etc.) to handle at each interrupt. */
+static int max_interrupt_work = 10;
+#ifdef CONFIG_PNP
+static int nopnp;
+#endif
+static int __init el3_common_init(struct net_device *dev);
+static void el3_common_remove(struct net_device *dev);
static ushort id_read_eeprom(int index);
static ushort read_eeprom(int ioaddr, int index);
static int el3_open(struct net_device *dev);
@@ -199,23 +203,279 @@
static void el3_down(struct net_device *dev);
static void el3_up(struct net_device *dev);
static const struct ethtool_ops ethtool_ops;
-#ifdef EL3_SUSPEND
+#ifdef CONFIG_PM
static int el3_suspend(struct device *, pm_message_t);
static int el3_resume(struct device *);
-#else
-#define el3_suspend NULL
-#define el3_resume NULL
#endif
/* generic device remove for all device types */
-#if defined(CONFIG_EISA) || defined(CONFIG_MCA)
static int el3_device_remove (struct device *device);
-#endif
#ifdef CONFIG_NET_POLL_CONTROLLER
static void el3_poll_controller(struct net_device *dev);
#endif
+/* Return 0 on success, 1 on error, 2 when found already detected PnP card */
+static int el3_isa_id_sequence(__be16 *phys_addr)
+{
+ short lrs_state = 0xff;
+ int i;
+
+ /* ISA boards are detected by sending the ID sequence to the
+ ID_PORT. We find cards past the first by setting the 'current_tag'
+ on cards as they are found. Cards with their tag set will not
+ respond to subsequent ID sequences. */
+
+ outb(0x00, id_port);
+ outb(0x00, id_port);
+ for (i = 0; i < 255; i++) {
+ outb(lrs_state, id_port);
+ lrs_state <<= 1;
+ lrs_state = lrs_state & 0x100 ? lrs_state ^ 0xcf : lrs_state;
+ }
+ /* For the first probe, clear all board's tag registers. */
+ if (current_tag == 0)
+ outb(0xd0, id_port);
+ else /* Otherwise kill off already-found boards. */
+ outb(0xd8, id_port);
+ if (id_read_eeprom(7) != 0x6d50)
+ return 1;
+ /* Read in EEPROM data, which does contention-select.
+ Only the lowest address board will stay "on-line".
+ 3Com got the byte order backwards. */
+ for (i = 0; i < 3; i++)
+ phys_addr[i] = htons(id_read_eeprom(i));
+#ifdef CONFIG_PNP
+ if (!nopnp) {
+ /* The ISA PnP 3c509 cards respond to the ID sequence too.
+ This check is needed in order not to register them twice. */
+ for (i = 0; i < el3_cards; i++) {
+ struct el3_private *lp = netdev_priv(el3_devs[i]);
+ if (lp->type == EL3_PNP
+ && !memcmp(phys_addr, el3_devs[i]->dev_addr,
+ ETH_ALEN)) {
+ if (el3_debug > 3)
+ printk(KERN_DEBUG "3c509 with address %02x %02x %02x %02x %02x %02x was found by ISAPnP\n",
+ phys_addr[0] & 0xff, phys_addr[0] >> 8,
+ phys_addr[1] & 0xff, phys_addr[1] >> 8,
+ phys_addr[2] & 0xff, phys_addr[2] >> 8);
+ /* Set the adaptor tag so that the next card can be found. */
+ outb(0xd0 + ++current_tag, id_port);
+ return 2;
+ }
+ }
+ }
+#endif /* CONFIG_PNP */
+ return 0;
+
+}
+
+static void __devinit el3_dev_fill(struct net_device *dev, __be16 *phys_addr,
+ int ioaddr, int irq, int if_port,
+ enum el3_cardtype type)
+{
+ struct el3_private *lp = netdev_priv(dev);
+
+ memcpy(dev->dev_addr, phys_addr, ETH_ALEN);
+ dev->base_addr = ioaddr;
+ dev->irq = irq;
+ dev->if_port = if_port;
+ lp->type = type;
+}
+
+static int __devinit el3_isa_match(struct device *pdev,
+ unsigned int ndev)
+{
+ struct net_device *dev;
+ int ioaddr, isa_irq, if_port, err;
+ unsigned int iobase;
+ __be16 phys_addr[3];
+
+ while ((err = el3_isa_id_sequence(phys_addr)) == 2)
+ ; /* Skip to next card when PnP card found */
+ if (err == 1)
+ return 0;
+
+ iobase = id_read_eeprom(8);
+ if_port = iobase >> 14;
+ ioaddr = 0x200 + ((iobase & 0x1f) << 4);
+ if (irq[el3_cards] > 1 && irq[el3_cards] < 16)
+ isa_irq = irq[el3_cards];
+ else
+ isa_irq = id_read_eeprom(9) >> 12;
+
+ dev = alloc_etherdev(sizeof(struct el3_private));
+ if (!dev)
+ return -ENOMEM;
+
+ netdev_boot_setup_check(dev);
+
+ if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509-isa")) {
+ free_netdev(dev);
+ return 0;
+ }
+
+ /* Set the adaptor tag so that the next card can be found. */
+ outb(0xd0 + ++current_tag, id_port);
+
+ /* Activate the adaptor at the EEPROM location. */
+ outb((ioaddr >> 4) | 0xe0, id_port);
+
+ EL3WINDOW(0);
+ if (inw(ioaddr) != 0x6d50) {
+ free_netdev(dev);
+ return 0;
+ }
+
+ /* Free the interrupt so that some other card can use it. */
+ outw(0x0f00, ioaddr + WN0_IRQ);
+
+ el3_dev_fill(dev, phys_addr, ioaddr, isa_irq, if_port, EL3_ISA);
+ dev_set_drvdata(pdev, dev);
+ if (el3_common_init(dev)) {
+ free_netdev(dev);
+ return 0;
+ }
+
+ el3_devs[el3_cards++] = dev;
+ return 1;
+}
+
+static int __devexit el3_isa_remove(struct device *pdev,
+ unsigned int ndev)
+{
+ el3_device_remove(pdev);
+ dev_set_drvdata(pdev, NULL);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int el3_isa_suspend(struct device *dev, unsigned int n,
+ pm_message_t state)
+{
+ current_tag = 0;
+ return el3_suspend(dev, state);
+}
+
+static int el3_isa_resume(struct device *dev, unsigned int n)
+{
+ struct net_device *ndev = dev_get_drvdata(dev);
+ int ioaddr = ndev->base_addr, err;
+ __be16 phys_addr[3];
+
+ while ((err = el3_isa_id_sequence(phys_addr)) == 2)
+ ; /* Skip to next card when PnP card found */
+ if (err == 1)
+ return 0;
+ /* Set the adaptor tag so that the next card can be found. */
+ outb(0xd0 + ++current_tag, id_port);
+ /* Enable the card */
+ outb((ioaddr >> 4) | 0xe0, id_port);
+ EL3WINDOW(0);
+ if (inw(ioaddr) != 0x6d50)
+ return 1;
+ /* Free the interrupt so that some other card can use it. */
+ outw(0x0f00, ioaddr + WN0_IRQ);
+ return el3_resume(dev);
+}
+#endif
+
+static struct isa_driver el3_isa_driver = {
+ .match = el3_isa_match,
+ .remove = __devexit_p(el3_isa_remove),
+#ifdef CONFIG_PM
+ .suspend = el3_isa_suspend,
+ .resume = el3_isa_resume,
+#endif
+ .driver = {
+ .name = "3c509"
+ },
+};
+static int isa_registered;
+
+#ifdef CONFIG_PNP
+static struct pnp_device_id el3_pnp_ids[] = {
+ { .id = "TCM5090" }, /* 3Com Etherlink III (TP) */
+ { .id = "TCM5091" }, /* 3Com Etherlink III */
+ { .id = "TCM5094" }, /* 3Com Etherlink III (combo) */
+ { .id = "TCM5095" }, /* 3Com Etherlink III (TPO) */
+ { .id = "TCM5098" }, /* 3Com Etherlink III (TPC) */
+ { .id = "PNP80f7" }, /* 3Com Etherlink III compatible */
+ { .id = "PNP80f8" }, /* 3Com Etherlink III compatible */
+ { .id = "" }
+};
+MODULE_DEVICE_TABLE(pnp, el3_pnp_ids);
+
+static int __devinit el3_pnp_probe(struct pnp_dev *pdev,
+ const struct pnp_device_id *id)
+{
+ short i;
+ int ioaddr, irq, if_port;
+ u16 phys_addr[3];
+ struct net_device *dev = NULL;
+ int err;
+
+ ioaddr = pnp_port_start(pdev, 0);
+ if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509-pnp"))
+ return -EBUSY;
+ irq = pnp_irq(pdev, 0);
+ EL3WINDOW(0);
+ for (i = 0; i < 3; i++)
+ phys_addr[i] = htons(read_eeprom(ioaddr, i));
+ if_port = read_eeprom(ioaddr, 8) >> 14;
+ dev = alloc_etherdev(sizeof(struct el3_private));
+ if (!dev) {
+ release_region(ioaddr, EL3_IO_EXTENT);
+ return -ENOMEM;
+ }
+ SET_NETDEV_DEV(dev, &pdev->dev);
+ netdev_boot_setup_check(dev);
+
+ el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_PNP);
+ pnp_set_drvdata(pdev, dev);
+ err = el3_common_init(dev);
+
+ if (err) {
+ pnp_set_drvdata(pdev, NULL);
+ free_netdev(dev);
+ return err;
+ }
+
+ el3_devs[el3_cards++] = dev;
+ return 0;
+}
+
+static void __devexit el3_pnp_remove(struct pnp_dev *pdev)
+{
+ el3_common_remove(pnp_get_drvdata(pdev));
+ pnp_set_drvdata(pdev, NULL);
+}
+
+#ifdef CONFIG_PM
+static int el3_pnp_suspend(struct pnp_dev *pdev, pm_message_t state)
+{
+ return el3_suspend(&pdev->dev, state);
+}
+
+static int el3_pnp_resume(struct pnp_dev *pdev)
+{
+ return el3_resume(&pdev->dev);
+}
+#endif
+
+static struct pnp_driver el3_pnp_driver = {
+ .name = "3c509",
+ .id_table = el3_pnp_ids,
+ .probe = el3_pnp_probe,
+ .remove = __devexit_p(el3_pnp_remove),
+#ifdef CONFIG_PM
+ .suspend = el3_pnp_suspend,
+ .resume = el3_pnp_resume,
+#endif
+};
+static int pnp_registered;
+#endif /* CONFIG_PNP */
+
#ifdef CONFIG_EISA
static struct eisa_device_id el3_eisa_ids[] = {
{ "TCM5092" },
@@ -230,13 +490,14 @@
static struct eisa_driver el3_eisa_driver = {
.id_table = el3_eisa_ids,
.driver = {
- .name = "3c509",
+ .name = "3c579",
.probe = el3_eisa_probe,
.remove = __devexit_p (el3_device_remove),
.suspend = el3_suspend,
.resume = el3_resume,
}
};
+static int eisa_registered;
#endif
#ifdef CONFIG_MCA
@@ -271,45 +532,9 @@
.resume = el3_resume,
},
};
+static int mca_registered;
#endif /* CONFIG_MCA */
-#if defined(__ISAPNP__)
-static struct isapnp_device_id el3_isapnp_adapters[] __initdata = {
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5090),
- (long) "3Com Etherlink III (TP)" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5091),
- (long) "3Com Etherlink III" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5094),
- (long) "3Com Etherlink III (combo)" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5095),
- (long) "3Com Etherlink III (TPO)" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('T', 'C', 'M'), ISAPNP_FUNCTION(0x5098),
- (long) "3Com Etherlink III (TPC)" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('P', 'N', 'P'), ISAPNP_FUNCTION(0x80f7),
- (long) "3Com Etherlink III compatible" },
- { ISAPNP_ANY_ID, ISAPNP_ANY_ID,
- ISAPNP_VENDOR('P', 'N', 'P'), ISAPNP_FUNCTION(0x80f8),
- (long) "3Com Etherlink III compatible" },
- { } /* terminate list */
-};
-
-static __be16 el3_isapnp_phys_addr[8][3];
-static int nopnp;
-#endif /* __ISAPNP__ */
-
-/* With the driver model introduction for EISA devices, both init
- * and cleanup have been split :
- * - EISA devices probe/remove starts in el3_eisa_probe/el3_device_remove
- * - MCA/ISA still use el3_probe
- *
- * Both call el3_common_init/el3_common_remove. */
-
static int __init el3_common_init(struct net_device *dev)
{
struct el3_private *lp = netdev_priv(dev);
@@ -360,231 +585,11 @@
static void el3_common_remove (struct net_device *dev)
{
- struct el3_private *lp = netdev_priv(dev);
-
- (void) lp; /* Keep gcc quiet... */
-#if defined(__ISAPNP__)
- if (lp->type == EL3_PNP)
- pnp_device_detach(to_pnp_dev(lp->dev));
-#endif
-
unregister_netdev (dev);
release_region(dev->base_addr, EL3_IO_EXTENT);
free_netdev (dev);
}
-static int __init el3_probe(int card_idx)
-{
- struct net_device *dev;
- struct el3_private *lp;
- short lrs_state = 0xff, i;
- int ioaddr, irq, if_port;
- __be16 phys_addr[3];
- static int current_tag;
- int err = -ENODEV;
-#if defined(__ISAPNP__)
- static int pnp_cards;
- struct pnp_dev *idev = NULL;
- int pnp_found = 0;
-
- if (nopnp == 1)
- goto no_pnp;
-
- for (i=0; el3_isapnp_adapters[i].vendor != 0; i++) {
- int j;
- while ((idev = pnp_find_dev(NULL,
- el3_isapnp_adapters[i].vendor,
- el3_isapnp_adapters[i].function,
- idev))) {
- if (pnp_device_attach(idev) < 0)
- continue;
- if (pnp_activate_dev(idev) < 0) {
-__again:
- pnp_device_detach(idev);
- continue;
- }
- if (!pnp_port_valid(idev, 0) || !pnp_irq_valid(idev, 0))
- goto __again;
- ioaddr = pnp_port_start(idev, 0);
- if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509 PnP")) {
- pnp_device_detach(idev);
- return -EBUSY;
- }
- irq = pnp_irq(idev, 0);
- if (el3_debug > 3)
- printk ("ISAPnP reports %s at i/o 0x%x, irq %d\n",
- (char*) el3_isapnp_adapters[i].driver_data, ioaddr, irq);
- EL3WINDOW(0);
- for (j = 0; j < 3; j++)
- el3_isapnp_phys_addr[pnp_cards][j] =
- phys_addr[j] =
- htons(read_eeprom(ioaddr, j));
- if_port = read_eeprom(ioaddr, 8) >> 14;
- dev = alloc_etherdev(sizeof (struct el3_private));
- if (!dev) {
- release_region(ioaddr, EL3_IO_EXTENT);
- pnp_device_detach(idev);
- return -ENOMEM;
- }
-
- SET_NETDEV_DEV(dev, &idev->dev);
- pnp_cards++;
-
- netdev_boot_setup_check(dev);
- pnp_found = 1;
- goto found;
- }
- }
-no_pnp:
-#endif /* __ISAPNP__ */
-
- /* Select an open I/O location at 0x1*0 to do contention select. */
- for ( ; id_port < 0x200; id_port += 0x10) {
- if (!request_region(id_port, 1, "3c509"))
- continue;
- outb(0x00, id_port);
- outb(0xff, id_port);
- if (inb(id_port) & 0x01){
- release_region(id_port, 1);
- break;
- } else
- release_region(id_port, 1);
- }
- if (id_port >= 0x200) {
- /* Rare -- do we really need a warning? */
- printk(" WARNING: No I/O port available for 3c509 activation.\n");
- return -ENODEV;
- }
-
- /* Next check for all ISA bus boards by sending the ID sequence to the
- ID_PORT. We find cards past the first by setting the 'current_tag'
- on cards as they are found. Cards with their tag set will not
- respond to subsequent ID sequences. */
-
- outb(0x00, id_port);
- outb(0x00, id_port);
- for(i = 0; i < 255; i++) {
- outb(lrs_state, id_port);
- lrs_state <<= 1;
- lrs_state = lrs_state & 0x100 ? lrs_state ^ 0xcf : lrs_state;
- }
-
- /* For the first probe, clear all board's tag registers. */
- if (current_tag == 0)
- outb(0xd0, id_port);
- else /* Otherwise kill off already-found boards. */
- outb(0xd8, id_port);
-
- if (id_read_eeprom(7) != 0x6d50) {
- return -ENODEV;
- }
-
- /* Read in EEPROM data, which does contention-select.
- Only the lowest address board will stay "on-line".
- 3Com got the byte order backwards. */
- for (i = 0; i < 3; i++) {
- phys_addr[i] = htons(id_read_eeprom(i));
- }
-
-#if defined(__ISAPNP__)
- if (nopnp == 0) {
- /* The ISA PnP 3c509 cards respond to the ID sequence.
- This check is needed in order not to register them twice. */
- for (i = 0; i < pnp_cards; i++) {
- if (phys_addr[0] == el3_isapnp_phys_addr[i][0] &&
- phys_addr[1] == el3_isapnp_phys_addr[i][1] &&
- phys_addr[2] == el3_isapnp_phys_addr[i][2])
- {
- if (el3_debug > 3)
- printk("3c509 with address %02x %02x %02x %02x %02x %02x was found by ISAPnP\n",
- phys_addr[0] & 0xff, phys_addr[0] >> 8,
- phys_addr[1] & 0xff, phys_addr[1] >> 8,
- phys_addr[2] & 0xff, phys_addr[2] >> 8);
- /* Set the adaptor tag so that the next card can be found. */
- outb(0xd0 + ++current_tag, id_port);
- goto no_pnp;
- }
- }
- }
-#endif /* __ISAPNP__ */
-
- {
- unsigned int iobase = id_read_eeprom(8);
- if_port = iobase >> 14;
- ioaddr = 0x200 + ((iobase & 0x1f) << 4);
- }
- irq = id_read_eeprom(9) >> 12;
-
- dev = alloc_etherdev(sizeof (struct el3_private));
- if (!dev)
- return -ENOMEM;
-
- netdev_boot_setup_check(dev);
-
- /* Set passed-in IRQ or I/O Addr. */
- if (dev->irq > 1 && dev->irq < 16)
- irq = dev->irq;
-
- if (dev->base_addr) {
- if (dev->mem_end == 0x3c509 /* Magic key */
- && dev->base_addr >= 0x200 && dev->base_addr <= 0x3e0)
- ioaddr = dev->base_addr & 0x3f0;
- else if (dev->base_addr != ioaddr)
- goto out;
- }
-
- if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509")) {
- err = -EBUSY;
- goto out;
- }
-
- /* Set the adaptor tag so that the next card can be found. */
- outb(0xd0 + ++current_tag, id_port);
-
- /* Activate the adaptor at the EEPROM location. */
- outb((ioaddr >> 4) | 0xe0, id_port);
-
- EL3WINDOW(0);
- if (inw(ioaddr) != 0x6d50)
- goto out1;
-
- /* Free the interrupt so that some other card can use it. */
- outw(0x0f00, ioaddr + WN0_IRQ);
-
-#if defined(__ISAPNP__)
- found: /* PNP jumps here... */
-#endif /* __ISAPNP__ */
-
- memcpy(dev->dev_addr, phys_addr, sizeof(phys_addr));
- dev->base_addr = ioaddr;
- dev->irq = irq;
- dev->if_port = if_port;
- lp = netdev_priv(dev);
-#if defined(__ISAPNP__)
- lp->dev = &idev->dev;
- if (pnp_found)
- lp->type = EL3_PNP;
-#endif
- err = el3_common_init(dev);
-
- if (err)
- goto out1;
-
- el3_cards++;
- lp->next_dev = el3_root_dev;
- el3_root_dev = dev;
- return 0;
-
-out1:
-#if defined(__ISAPNP__)
- if (idev)
- pnp_device_detach(idev);
-#endif
-out:
- free_netdev(dev);
- return err;
-}
-
#ifdef CONFIG_MCA
static int __init el3_mca_probe(struct device *device)
{
@@ -596,7 +601,6 @@
* redone for multi-card detection by ZP Gu (zpg@...tle.net)
* now works as a module */
- struct el3_private *lp;
short i;
int ioaddr, irq, if_port;
u16 phys_addr[3];
@@ -613,7 +617,7 @@
irq = pos5 & 0x0f;
- printk("3c529: found %s at slot %d\n",
+ printk(KERN_INFO "3c529: found %s at slot %d\n",
el3_mca_adapter_names[mdev->index], slot + 1);
/* claim the slot */
@@ -626,7 +630,7 @@
irq = mca_device_transform_irq(mdev, irq);
ioaddr = mca_device_transform_ioport(mdev, ioaddr);
if (el3_debug > 2) {
- printk("3c529: irq %d ioaddr 0x%x ifport %d\n", irq, ioaddr, if_port);
+ printk(KERN_DEBUG "3c529: irq %d ioaddr 0x%x ifport %d\n", irq, ioaddr, if_port);
}
EL3WINDOW(0);
for (i = 0; i < 3; i++) {
@@ -641,13 +645,7 @@
netdev_boot_setup_check(dev);
- memcpy(dev->dev_addr, phys_addr, sizeof(phys_addr));
- dev->base_addr = ioaddr;
- dev->irq = irq;
- dev->if_port = if_port;
- lp = netdev_priv(dev);
- lp->dev = device;
- lp->type = EL3_MCA;
+ el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_MCA);
device->driver_data = dev;
err = el3_common_init(dev);
@@ -657,7 +655,7 @@
return -ENOMEM;
}
- el3_cards++;
+ el3_devs[el3_cards++] = dev;
return 0;
}
@@ -666,7 +664,6 @@
#ifdef CONFIG_EISA
static int __init el3_eisa_probe (struct device *device)
{
- struct el3_private *lp;
short i;
int ioaddr, irq, if_port;
u16 phys_addr[3];
@@ -678,7 +675,7 @@
edev = to_eisa_device (device);
ioaddr = edev->base_addr;
- if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509"))
+ if (!request_region(ioaddr, EL3_IO_EXTENT, "3c579-eisa"))
return -EBUSY;
/* Change the register set to the configuration window 0. */
@@ -700,13 +697,7 @@
netdev_boot_setup_check(dev);
- memcpy(dev->dev_addr, phys_addr, sizeof(phys_addr));
- dev->base_addr = ioaddr;
- dev->irq = irq;
- dev->if_port = if_port;
- lp = netdev_priv(dev);
- lp->dev = device;
- lp->type = EL3_EISA;
+ el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_EISA);
eisa_set_drvdata (edev, dev);
err = el3_common_init(dev);
@@ -716,12 +707,11 @@
return err;
}
- el3_cards++;
+ el3_devs[el3_cards++] = dev;
return 0;
}
#endif
-#if defined(CONFIG_EISA) || defined(CONFIG_MCA)
/* This remove works for all device types.
*
* The net dev must be stored in the driver_data field */
@@ -734,7 +724,6 @@
el3_common_remove (dev);
return 0;
}
-#endif
/* Read a word from the EEPROM using the regular EEPROM access register.
Assume that we are in register window zero.
@@ -749,7 +738,7 @@
}
/* Read a word from the EEPROM when in the ISA ID probe state. */
-static ushort __init id_read_eeprom(int index)
+static ushort id_read_eeprom(int index)
{
int bit, word = 0;
@@ -765,7 +754,7 @@
word = (word << 1) + (inb(id_port) & 0x01);
if (el3_debug > 3)
- printk(" 3c509 EEPROM word %d %#4.4x.\n", index, word);
+ printk(KERN_DEBUG " 3c509 EEPROM word %d %#4.4x.\n", index, word);
return word;
}
@@ -787,13 +776,13 @@
EL3WINDOW(0);
if (el3_debug > 3)
- printk("%s: Opening, IRQ %d status@%x %4.4x.\n", dev->name,
+ printk(KERN_DEBUG "%s: Opening, IRQ %d status@%x %4.4x.\n", dev->name,
dev->irq, ioaddr + EL3_STATUS, inw(ioaddr + EL3_STATUS));
el3_up(dev);
if (el3_debug > 3)
- printk("%s: Opened 3c509 IRQ %d status %4.4x.\n",
+ printk(KERN_DEBUG "%s: Opened 3c509 IRQ %d status %4.4x.\n",
dev->name, dev->irq, inw(ioaddr + EL3_STATUS));
return 0;
@@ -806,7 +795,7 @@
int ioaddr = dev->base_addr;
/* Transmitter timeout, serious problems. */
- printk("%s: transmit timed out, Tx_status %2.2x status %4.4x "
+ printk(KERN_WARNING "%s: transmit timed out, Tx_status %2.2x status %4.4x "
"Tx FIFO room %d.\n",
dev->name, inb(ioaddr + TX_STATUS), inw(ioaddr + EL3_STATUS),
inw(ioaddr + TX_FREE));
@@ -831,7 +820,7 @@
lp->stats.tx_bytes += skb->len;
if (el3_debug > 4) {
- printk("%s: el3_start_xmit(length = %u) called, status %4.4x.\n",
+ printk(KERN_DEBUG "%s: el3_start_xmit(length = %u) called, status %4.4x.\n",
dev->name, skb->len, inw(ioaddr + EL3_STATUS));
}
#if 0
@@ -840,7 +829,7 @@
ushort status = inw(ioaddr + EL3_STATUS);
if (status & 0x0001 /* IRQ line active, missed one. */
&& inw(ioaddr + EL3_STATUS) & 1) { /* Make sure. */
- printk("%s: Missed interrupt, status then %04x now %04x"
+ printk(KERN_DEBUG "%s: Missed interrupt, status then %04x now %04x"
" Tx %2.2x Rx %4.4x.\n", dev->name, status,
inw(ioaddr + EL3_STATUS), inb(ioaddr + TX_STATUS),
inw(ioaddr + RX_STATUS));
@@ -914,7 +903,7 @@
if (el3_debug > 4) {
status = inw(ioaddr + EL3_STATUS);
- printk("%s: interrupt, status %4.4x.\n", dev->name, status);
+ printk(KERN_DEBUG "%s: interrupt, status %4.4x.\n", dev->name, status);
}
while ((status = inw(ioaddr + EL3_STATUS)) &
@@ -925,7 +914,7 @@
if (status & TxAvailable) {
if (el3_debug > 5)
- printk(" TX room bit was handled.\n");
+ printk(KERN_DEBUG " TX room bit was handled.\n");
/* There's room in the FIFO for a full-sized packet. */
outw(AckIntr | TxAvailable, ioaddr + EL3_CMD);
netif_wake_queue (dev);
@@ -964,7 +953,7 @@
}
if (--i < 0) {
- printk("%s: Infinite loop in interrupt, status %4.4x.\n",
+ printk(KERN_ERR "%s: Infinite loop in interrupt, status %4.4x.\n",
dev->name, status);
/* Clear all interrupts. */
outw(AckIntr | 0xFF, ioaddr + EL3_CMD);
@@ -975,7 +964,7 @@
}
if (el3_debug > 4) {
- printk("%s: exiting interrupt, status %4.4x.\n", dev->name,
+ printk(KERN_DEBUG "%s: exiting interrupt, status %4.4x.\n", dev->name,
inw(ioaddr + EL3_STATUS));
}
spin_unlock(&lp->lock);
@@ -1450,7 +1439,7 @@
}
/* Power Management support functions */
-#ifdef EL3_SUSPEND
+#ifdef CONFIG_PM
static int
el3_suspend(struct device *pdev, pm_message_t state)
@@ -1500,79 +1489,102 @@
return 0;
}
-#endif /* EL3_SUSPEND */
-
-/* Parameters that may be passed into the module. */
-static int debug = -1;
-static int irq[] = {-1, -1, -1, -1, -1, -1, -1, -1};
-static int xcvr[] = {-1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1};
+#endif /* CONFIG_PM */
module_param(debug,int, 0);
module_param_array(irq, int, NULL, 0);
-module_param_array(xcvr, int, NULL, 0);
module_param(max_interrupt_work, int, 0);
MODULE_PARM_DESC(debug, "debug level (0-6)");
MODULE_PARM_DESC(irq, "IRQ number(s) (assigned)");
-MODULE_PARM_DESC(xcvr,"transceiver(s) (0=internal, 1=external)");
MODULE_PARM_DESC(max_interrupt_work, "maximum events handled per interrupt");
-#if defined(__ISAPNP__)
+#ifdef CONFIG_PNP
module_param(nopnp, int, 0);
MODULE_PARM_DESC(nopnp, "disable ISA PnP support (0-1)");
-MODULE_DEVICE_TABLE(isapnp, el3_isapnp_adapters);
-#endif /* __ISAPNP__ */
-MODULE_DESCRIPTION("3Com Etherlink III (3c509, 3c509B) ISA/PnP ethernet driver");
+#endif /* CONFIG_PNP */
+MODULE_DESCRIPTION("3Com Etherlink III (3c509, 3c509B, 3c529, 3c579) ethernet driver");
MODULE_LICENSE("GPL");
static int __init el3_init_module(void)
{
int ret = 0;
- el3_cards = 0;
if (debug >= 0)
el3_debug = debug;
- el3_root_dev = NULL;
- while (el3_probe(el3_cards) == 0) {
- if (irq[el3_cards] > 1)
- el3_root_dev->irq = irq[el3_cards];
- if (xcvr[el3_cards] >= 0)
- el3_root_dev->if_port = xcvr[el3_cards];
- el3_cards++;
+#ifdef CONFIG_PNP
+ if (!nopnp) {
+ ret = pnp_register_driver(&el3_pnp_driver);
+ if (!ret)
+ pnp_registered = 1;
+ }
+#endif
+ /* Select an open I/O location at 0x1*0 to do ISA contention select. */
+ /* Start with 0x110 to avoid some sound cards.*/
+ for (id_port = 0x110 ; id_port < 0x200; id_port += 0x10) {
+ if (!request_region(id_port, 1, "3c509-control"))
+ continue;
+ outb(0x00, id_port);
+ outb(0xff, id_port);
+ if (inb(id_port) & 0x01)
+ break;
+ else
+ release_region(id_port, 1);
+ }
+ if (id_port >= 0x200) {
+ id_port = 0;
+ printk(KERN_ERR "No I/O port available for 3c509 activation.\n");
+ } else {
+ ret = isa_register_driver(&el3_isa_driver, EL3_MAX_CARDS);
+ if (!ret)
+ isa_registered = 1;
}
-
#ifdef CONFIG_EISA
ret = eisa_driver_register(&el3_eisa_driver);
+ if (!ret)
+ eisa_registered = 1;
#endif
#ifdef CONFIG_MCA
- {
- int err = mca_register_driver(&el3_mca_driver);
- if (ret == 0)
- ret = err;
- }
+ ret = mca_register_driver(&el3_mca_driver);
+ if (!ret)
+ mca_registered = 1;
+#endif
+
+#ifdef CONFIG_PNP
+ if (pnp_registered)
+ ret = 0;
+#endif
+ if (isa_registered)
+ ret = 0;
+#ifdef CONFIG_EISA
+ if (eisa_registered)
+ ret = 0;
+#endif
+#ifdef CONFIG_MCA
+ if (mca_registered)
+ ret = 0;
#endif
return ret;
}
static void __exit el3_cleanup_module(void)
{
- struct net_device *next_dev;
-
- while (el3_root_dev) {
- struct el3_private *lp = netdev_priv(el3_root_dev);
-
- next_dev = lp->next_dev;
- el3_common_remove (el3_root_dev);
- el3_root_dev = next_dev;
- }
-
+#ifdef CONFIG_PNP
+ if (pnp_registered)
+ pnp_unregister_driver(&el3_pnp_driver);
+#endif
+ if (isa_registered)
+ isa_unregister_driver(&el3_isa_driver);
+ if (id_port)
+ release_region(id_port, 1);
#ifdef CONFIG_EISA
- eisa_driver_unregister (&el3_eisa_driver);
+ if (eisa_registered)
+ eisa_driver_unregister(&el3_eisa_driver);
#endif
#ifdef CONFIG_MCA
- mca_unregister_driver(&el3_mca_driver);
+ if (mca_registered)
+ mca_unregister_driver(&el3_mca_driver);
#endif
}
module_init (el3_init_module);
module_exit (el3_cleanup_module);
-
--
Ondrej Zary
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists