[ 0.000000] Linux version 2.6.25-rc4 (nmarci@europa) (gcc version 4.2.3 20080114 (prerelease) (Debian 4.2.2-7)) #6 PREEMPT Sat Mar 8 08:11:47 CET 2008 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003bf70000 (usable) [ 0.000000] BIOS-e820: 000000003bf70000 - 000000003bf7a000 (ACPI data) [ 0.000000] BIOS-e820: 000000003bf7a000 - 000000003bf80000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003bf80000 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved) [ 0.000000] 63MB HIGHMEM available. [ 0.000000] 896MB LOWMEM available. [ 0.000000] Scan SMP from c0000000 for 1024 bytes. [ 0.000000] Scan SMP from c009fc00 for 1024 bytes. [ 0.000000] Scan SMP from c00f0000 for 65536 bytes. [ 0.000000] found SMP MP-table at [c00f6870] 000f6870 [ 0.000000] Entering add_active_range(0, 0, 245616) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 229376 [ 0.000000] HighMem 229376 -> 245616 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 245616 [ 0.000000] On node 0 totalpages: 245616 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1760 pages used for memmap [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 [ 0.000000] HighMem zone: 126 pages used for memmap [ 0.000000] HighMem zone: 16114 pages, LIFO batch:3 [ 0.000000] Movable zone: 0 pages used for memmap [ 0.000000] DMI present. [ 0.000000] ACPI: RSDP 000F68D0, 0014 (r0 PTLTD ) [ 0.000000] ACPI: RSDT 3BF7600B, 0030 (r1 PTLTD RSDT 6040000 LTP 0) [ 0.000000] ACPI: FACP 3BF79E87, 0074 (r1 AMDK8 PTLTW 6040000 PTL_ F4240) [ 0.000000] ACPI: DSDT 3BF7603B, 3E4C (r1 VIA PTL_ACPI 6040000 MSFT 100000E) [ 0.000000] ACPI: FACS 3BF7AFC0, 0040 [ 0.000000] ACPI: SSDT 3BF79EFB, 00B5 (r1 PTLTD POWERNOW 6040000 LTP 1) [ 0.000000] ACPI: APIC 3BF79FB0, 0050 (r1 PTLTD APIC 6040000 LTP 0) [ 0.000000] ACPI: PM-Timer IO Port: 0x4008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:12 APIC version 16 [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ10 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:bffe0000) [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d8000 [ 0.000000] PM: Registered nosave memory: 00000000000d8000 - 0000000000100000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 243698 [ 0.000000] Kernel command line: root=/dev/hda3 ro log_buf_len=1M resume=/dev/hda2 [ 0.000000] log_buf_len: 1048576 [ 0.000000] mapped APIC to ffffb000 (fee00000) [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1603.642 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.000999] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.000999] ... MAX_LOCK_DEPTH: 48 [ 0.000999] ... MAX_LOCKDEP_KEYS: 2048 [ 0.000999] ... CLASSHASH_SIZE: 1024 [ 0.000999] ... MAX_LOCKDEP_ENTRIES: 8192 [ 0.000999] ... MAX_LOCKDEP_CHAINS: 16384 [ 0.000999] ... CHAINHASH_SIZE: 8192 [ 0.000999] memory used by lock dependency info: 992 kB [ 0.000999] per task-struct memory footprint: 1920 bytes [ 0.000999] ------------------------ [ 0.000999] | Locking API testsuite: [ 0.000999] ---------------------------------------------------------------------------- [ 0.000999] | spin |wlock |rlock |mutex | wsem | rsem | [ 0.000999] -------------------------------------------------------------------------- [ 0.000999] A-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-B-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-B-C-C-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-C-A-B-C deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-B-C-C-D-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-C-D-B-D-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] A-B-C-D-B-C-D-A deadlock: ok | ok | ok | ok | ok | ok | [ 0.000999] double unlock: ok | ok | ok | ok | ok | ok | [ 0.000999] initialize held: ok | ok | ok | ok | ok | ok | [ 0.000999] bad unlock order: ok | ok | ok | ok | ok | ok | [ 0.000999] -------------------------------------------------------------------------- [ 0.000999] recursive read-lock: | ok | | ok | [ 0.000999] recursive read-lock #2: | ok | | ok | [ 0.000999] mixed read-write-lock: | ok | | ok | [ 0.000999] mixed write-read-lock: | ok | | ok | [ 0.000999] -------------------------------------------------------------------------- [ 0.000999] hard-irqs-on + irq-safe-A/12: ok | ok | ok | [ 0.000999] soft-irqs-on + irq-safe-A/12: ok | ok | ok | [ 0.000999] hard-irqs-on + irq-safe-A/21: ok | ok | ok | [ 0.000999] soft-irqs-on + irq-safe-A/21: ok | ok | ok | [ 0.000999] sirq-safe-A => hirqs-on/12: ok | ok | ok | [ 0.000999] sirq-safe-A => hirqs-on/21: ok | ok | ok | [ 0.000999] hard-safe-A + irqs-on/12: ok | ok | ok | [ 0.000999] soft-safe-A + irqs-on/12: ok | ok | ok | [ 0.000999] hard-safe-A + irqs-on/21: ok | ok | ok | [ 0.000999] soft-safe-A + irqs-on/21: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/123: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/123: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/132: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/132: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/213: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/213: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/231: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/231: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/312: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/312: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #1/321: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #1/321: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/123: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/123: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/132: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/132: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/213: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/213: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/231: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/231: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/312: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/312: ok | ok | ok | [ 0.000999] hard-safe-A + unsafe-B #2/321: ok | ok | ok | [ 0.000999] soft-safe-A + unsafe-B #2/321: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/123: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/123: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/132: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/132: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/213: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/213: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/231: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/231: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/312: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/312: ok | ok | ok | [ 0.000999] hard-irq lock-inversion/321: ok | ok | ok | [ 0.000999] soft-irq lock-inversion/321: ok | ok | ok | [ 0.000999] hard-irq read-recursion/123: ok | [ 0.000999] soft-irq read-recursion/123: ok | [ 0.000999] hard-irq read-recursion/132: ok | [ 0.000999] soft-irq read-recursion/132: ok | [ 0.000999] hard-irq read-recursion/213: ok | [ 0.000999] soft-irq read-recursion/213: ok | [ 0.000999] hard-irq read-recursion/231: ok | [ 0.000999] soft-irq read-recursion/231: ok | [ 0.000999] hard-irq read-recursion/312: ok | [ 0.000999] soft-irq read-recursion/312: ok | [ 0.000999] hard-irq read-recursion/321: ok | [ 0.000999] soft-irq read-recursion/321: ok | [ 0.000999] ------------------------------------------------------- [ 0.000999] Good, all 218 testcases passed! | [ 0.000999] --------------------------------- [ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000999] Memory: 966876k/982464k available (2073k kernel code, 15072k reserved, 889k data, 272k init, 64960k highmem) [ 0.000999] virtual kernel memory layout: [ 0.000999] fixmap : 0xfffa8000 - 0xfffff000 ( 348 kB) [ 0.000999] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.000999] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) [ 0.000999] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) [ 0.000999] .init : 0xc03e8000 - 0xc042c000 ( 272 kB) [ 0.000999] .data : 0xc030654b - 0xc03e4c18 ( 889 kB) [ 0.000999] .text : 0xc0100000 - 0xc030654b (2073 kB) [ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated [ 0.060995] Calibrating delay using timer specific routine.. 3210.58 BogoMIPS (lpj=1605290) [ 0.061255] Mount-cache hash table entries: 512 [ 0.062190] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.062995] CPU: L2 Cache: 128K (64 bytes/line) [ 0.063051] Intel machine check architecture supported. [ 0.063108] Intel machine check reporting enabled on CPU#0. [ 0.063171] Compat vDSO mapped to ffffe000. [ 0.063231] CPU: AMD Mobile AMD Sempron(tm) Processor 2600+ stepping 00 [ 0.063407] Checking 'hlt' instruction... OK. [ 0.067334] Freeing SMP alternatives: 0k freed [ 0.067389] ACPI: Core revision 20070126 [ 0.075700] Parsing all Control Methods: [ 0.075829] Table [DSDT](id 0001) - 480 Objects with 49 Devices 147 Methods 13 Regions [ 0.076045] Parsing all Control Methods: [ 0.076167] Table [SSDT](id 0002) - 3 Objects with 0 Devices 0 Methods 0 Regions [ 0.076282] tbxface-0598 [00] tb_load_namespace : ACPI Tables successfully acquired [ 0.077049] evxfevnt-0091 [00] enable : Transition to ACPI mode successful [ 0.078951] ENABLING IO-APIC IRQs [ 0.078988] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 [ 0.088986] net_namespace: 604 bytes [ 0.089542] NET: Registered protocol family 16 [ 0.090468] EISA bus registered [ 0.090552] ACPI: bus type pci registered [ 0.098184] PCI: PCI BIOS revision 2.10 entry at 0xfd88c, last bus=1 [ 0.098246] PCI: Using configuration type 1 [ 0.098301] Setting up standard PCI resources [ 0.102693] evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 0F [_GPE] 2 regs on int 0xA [ 0.103507] evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 4 Wake, Enabled 0 Runtime GPEs in this block [ 0.103662] ACPI: EC: Look up EC in DSDT [ 0.105968] Completing Region/Field/Buffer/Package initialization:..................................................... [ 0.112059] Initialized 11/13 Regions 1/1 Fields 23/24 Buffers 18/26 Packages (492 nodes) [ 0.112176] Initializing Device/Processor/Thermal objects by executing _INI methods:. [ 0.112520] Executed 1 _INI methods requiring 1 _STA executions (examined 53 objects) [ 0.112710] ACPI: Interpreter enabled [ 0.112765] ACPI: (supports S0 S3 S4 S5) [ 0.113073] ACPI: Using IOAPIC for interrupt routing [ 0.124960] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 0.141100] ACPI: EC: GPE = 0xb, I/O: command/status = 0x66, data = 0x62 [ 0.141163] ACPI: EC: driver started in interrupt mode [ 0.141406] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.142668] pci 0000:00:11.0: quirk: region 4000-407f claimed by vt8235 PM [ 0.142730] pci 0000:00:11.0: quirk: region 8100-810f claimed by vt8235 SMB [ 0.143303] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.163710] ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *9, disabled. [ 0.164421] ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *11, disabled. [ 0.165135] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *10, disabled. [ 0.165538] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *5, disabled. [ 0.166042] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 12 14 15) [ 0.166735] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 12 14 15) *11 [ 0.167461] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 11 12 14 15) *10 [ 0.168174] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15) [ 0.169139] Linux Plug and Play Support v0.97 (c) Adam Belay [ 0.169323] pnp: PnP ACPI init [ 0.169421] ACPI: bus type pnp registered [ 0.171596] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) [ 0.172380] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.172644] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.172904] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.173225] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.173355] 00:05: calling quirk 0xc025ae70: quirk_supermicro_h8dce_system+0x0/0x110() [ 0.173531] pnp 00:05: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.173827] 00:06: calling quirk 0xc025ae70: quirk_supermicro_h8dce_system+0x0/0x110() [ 0.174030] pnp 00:06: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.174292] pnp 00:07: Plug and Play ACPI device, IDs PNP0f13 (active) [ 0.174537] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.175664] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.176873] pnp 00:0a: Plug and Play ACPI device, IDs PNP0401 (active) [ 0.677904] ACPI: EC: missing write data confirmation, don't expect it any longer. [ 0.677904] pnp: PnP ACPI: found 11 devices [ 0.677904] ACPI: ACPI bus type pnp unregistered [ 0.678131] PCI: Using ACPI for IRQ routing [ 0.678191] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 0.682723] pnp: the driver 'system' has been registered [ 0.682758] system 00:05: iomem range 0x0-0x9ffff could not be reserved [ 0.682821] system 00:05: iomem range 0xe0000-0xfffff could not be reserved [ 0.682882] system 00:05: iomem range 0xfff00000-0xffffffff could not be reserved [ 0.682903] Time: tsc clocksource has been installed. [ 0.682911] system 00:05: iomem range 0xffee0000-0xffefffff has been reserved [ 0.682982] system 00:05: iomem range 0xfec00000-0xfec00fff has been reserved [ 0.683042] system 00:05: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.683100] system 00:05: driver attached [ 0.683114] system 00:06: ioport range 0x4d0-0x4d1 has been reserved [ 0.683174] system 00:06: ioport range 0xfe10-0xfe11 has been reserved [ 0.683233] system 00:06: ioport range 0xfe00-0xfe00 has been reserved [ 0.683292] system 00:06: ioport range 0x4000-0x407f has been reserved [ 0.683351] system 00:06: ioport range 0x8100-0x811f could not be reserved [ 0.683410] system 00:06: driver attached [ 0.715412] PCI: Bridge: 0000:00:01.0 [ 0.715472] IO window: disabled. [ 0.715529] MEM window: 0xd1000000-0xd1ffffff [ 0.715586] PREFETCH window: 0x00000000f0000000-0x00000000f3ffffff [ 0.715649] PCI: Bus 2, cardbus bridge: 0000:00:0c.0 [ 0.715704] IO window: 0x00002000-0x000020ff [ 0.715761] IO window: 0x00002400-0x000024ff [ 0.715818] PREFETCH window: 0x50000000-0x53ffffff [ 0.715876] MEM window: 0x54000000-0x57ffffff [ 0.715930] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 0.715944] PCI: Enabling device 0000:00:0c.0 (0000 -> 0003) [ 0.716013] ACPI: PCI Interrupt 0000:00:0c.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 0.716129] PCI: Setting latency timer of device 0000:00:0c.0 to 64 [ 0.716199] NET: Registered protocol family 2 [ 0.716511] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.717330] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.718602] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) [ 0.724795] TCP: Hash tables configured (established 131072 bind 65536) [ 0.724901] TCP reno registered [ 0.727749] audit: initializing netlink socket (disabled) [ 0.727861] type=2000 audit(1204964371.726:1): initialized [ 0.728288] highmem bounce pool size: 64 pages [ 0.729091] io scheduler noop registered [ 0.729166] io scheduler cfq registered (default) [ 0.729244] PCI: VIA PCI bridge detected. Disabling DAC. [ 0.729381] pci 0000:01:00.0: Boot video device [ 0.729790] isapnp: Scanning for PnP cards... [ 1.086836] isapnp: No Plug & Play device found [ 1.173786] Uniform Multi-Platform E-IDE driver [ 1.173917] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 1.174167] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:11.1 [ 1.174480] ACPI: PCI Interrupt Link [ALKA] disabled and referenced, BIOS bug [ 1.174645] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 23 [ 1.174705] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 23 [ 1.174769] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 23 (level, low) -> IRQ 23 [ 1.174947] VP_IDE: not 100% native mode: will probe irqs later [ 1.175016] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 [ 1.175093] ide0: BM-DMA at 0x1c60-0x1c67, BIOS settings: hda:DMA, hdb:PIO [ 1.175210] ide1: BM-DMA at 0x1c68-0x1c6f, BIOS settings: hdc:DMA, hdd:PIO [ 1.175323] Probing IDE interface ide0... [ 1.215863] Switched to high resolution mode on CPU 0 [ 1.714337] hdb: IRQ probe failed (0xfffffbfe) [ 1.988460] hdb: IRQ probe failed (0xfffffbfe) [ 2.415565] hda: SAMSUNG MP0804H, ATA DISK drive [ 2.415565] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 2.415565] hda: UDMA/100 mode selected [ 2.415565] Probing IDE interface ide1... [ 3.819842] hdc: Optiarc DVD RW AD-7543A, ATAPI CD/DVD-ROM drive [ 3.819842] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4 [ 3.819842] hdc: UDMA/33 mode selected [ 3.819842] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 3.915658] ide1 at 0x170-0x177,0x376 on irq 15 [ 3.918118] pnp: the driver 'ide' has been registered [ 3.918312] hda: max request size: 512KiB [ 3.918460] hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63 [ 3.919383] hda: cache flushes supported [ 3.919421] hda: hda1 hda2 hda3 [ 3.923633] TCP cubic registered [ 3.923717] NET: Registered protocol family 1 [ 3.923797] NET: Registered protocol family 17 [ 3.923877] Using IPI Shortcut mode [ 3.958646] ReiserFS: hda3: found reiserfs format "3.6" with standard journal [ 3.958646] ReiserFS: hda3: using ordered data mode [ 3.968162] ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 3.969498] ReiserFS: hda3: checking transaction log (hda3) [ 4.050340] ReiserFS: hda3: Using r5 hash to sort names [ 4.050340] VFS: Mounted root (reiserfs filesystem) readonly. [ 4.050340] Freeing unused kernel memory: 272k freed [ 4.050340] Write protecting the kernel read-only data: 728k [ 9.247539] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 9.247914] ACPI: ACPI0007:00 is registered as cooling_device0 [ 9.261698] input: Power Button (FF) as /class/input/input0 [ 9.264750] ACPI: Power Button (FF) [PWRF] [ 9.265023] input: Power Button (CM) as /class/input/input1 [ 9.267742] ACPI: Power Button (CM) [PWB] [ 9.267989] input: Sleep Button (CM) as /class/input/input2 [ 9.271693] ACPI: Sleep Button (CM) [SLPB] [ 9.271930] input: Lid Switch as /class/input/input3 [ 9.272250] ACPI: Lid Switch [LID] [ 9.275160] ACPI thermal trips update, flag is 1f [ 9.275295] Checking invalid passive trip point... [ 9.275848] Checking invalid active[0] trip point... [ 9.276433] ACPI: LNXTHERM:01 is registered as thermal_zone0 [ 9.276840] ACPI: Thermal Zone [THRM] (51 C) [ 9.283907] ACPI: AC Adapter [AC] (on-line) [ 9.298824] ACPI: Battery Slot [BAT0] (battery present) [ 9.779278] 8139too Fast Ethernet driver 0.9.28 [ 9.779413] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 19 [ 9.780486] eth0: RealTek RTL8139 at 0xf88e6000, 00:90:f5:3e:5a:ca, IRQ 19 [ 9.780547] eth0: Identified 8139 chip type 'RTL-8100B/8139D' [ 9.926250] usbcore: registered new interface driver usbfs [ 9.926722] usbcore: registered new interface driver hub [ 9.932594] usbcore: registered new device driver usb [ 9.970145] Yenta: CardBus bridge found at 0000:00:0c.0 [1558:4702] [ 9.970231] Yenta: Using CSCINT to route CSC interrupts to PCI [ 9.970288] Yenta: Routing CardBus interrupts to PCI [ 9.970347] Yenta TI: socket 0000:00:0c.0, mfunc 0x00001002, devctl 0x44 [ 10.082540] Marking TSC unstable due to: possible TSC halt in C2. [ 10.088159] Time: acpi_pm clocksource has been installed. [ 10.124294] Yenta: ISA IRQ mask 0x0888, PCI irq 16 [ 10.124356] Socket status: 30000006 [ 10.283070] Real Time Clock Driver v1.12ac [ 10.323892] pnp: the driver 'parport_pc' has been registered [ 10.323925] parport_pc 00:0a: reported by Plug and Play ACPI [ 10.324206] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] [ 10.364197] input: PC Speaker as /class/input/input4 [ 10.405891] parport_pc 00:0a: driver attached [ 10.664614] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [ 10.665559] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 10.690614] pnp: the driver 'serial' has been registered [ 10.693403] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 10.693650] serial 00:09: driver attached [ 10.719440] USB Universal Host Controller Interface driver v3.0 [ 10.719731] ACPI: PCI Interrupt Link [ALKD] disabled and referenced, BIOS bug [ 10.720129] ACPI: PCI Interrupt Link [ALKD] BIOS reported IRQ 0, using IRQ 21 [ 10.720189] ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 21 [ 10.720253] ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21 [ 10.720490] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 10.729144] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 [ 10.729274] uhci_hcd 0000:00:10.0: irq 21, io base 0x00001c00 [ 10.732056] usb usb1: configuration #1 chosen from 1 choice [ 10.734226] hub 1-0:1.0: USB hub found [ 10.734910] hub 1-0:1.0: 2 ports detected [ 10.822875] hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache [ 10.823187] Uniform CD-ROM driver Revision: 3.20 [ 10.835896] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21 [ 10.836091] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 10.836526] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 [ 10.836630] uhci_hcd 0000:00:10.1: irq 21, io base 0x00001c20 [ 10.837018] usb usb2: configuration #1 chosen from 1 choice [ 10.837526] hub 2-0:1.0: USB hub found [ 10.837599] hub 2-0:1.0: 2 ports detected [ 10.934718] ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21 [ 10.934889] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 10.935031] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 [ 10.935145] uhci_hcd 0000:00:10.2: irq 21, io base 0x00001c40 [ 10.935575] usb usb3: configuration #1 chosen from 1 choice [ 10.935712] hub 3-0:1.0: USB hub found [ 10.935788] hub 3-0:1.0: 2 ports detected [ 11.036784] ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [ALKD] -> GSI 21 (level, low) -> IRQ 21 [ 11.036964] ehci_hcd 0000:00:10.3: EHCI Host Controller [ 11.037107] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 [ 11.037253] ehci_hcd 0000:00:10.3: irq 21, io mem 0xd0004400 [ 11.043452] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 11.043862] usb usb4: configuration #1 chosen from 1 choice [ 11.043994] hub 4-0:1.0: USB hub found [ 11.044427] hub 4-0:1.0: 6 ports detected [ 11.337448] cs: IO port probe 0x100-0x4ff: clean. [ 11.341653] cs: IO port probe 0x800-0x8ff: clean. [ 11.342764] cs: IO port probe 0xc00-0xcff: clean. [ 11.344099] cs: IO port probe 0xa00-0xaff: clean. [ 11.359967] ACPI: PCI Interrupt Link [ALKC] disabled and referenced, BIOS bug [ 11.360446] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22 [ 11.360507] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22 [ 11.360570] ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22 [ 11.365193] PCI: Setting latency timer of device 0000:00:11.6 to 64 [ 11.871190] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 22 [ 11.871492] PCI: Setting latency timer of device 0000:00:11.5 to 64 [ 14.695432] Adding 1951888k swap on /dev/hda2. Priority:-1 extents:1 across:1951888k [ 21.342637] ACPI thermal trips update, flag is c [ 21.342701] Checking valid passive trip point... [ 21.343243] Checking invalid active[0] trip point... [ 21.343342] ACPI Exception (thermal-0516): AE_ERROR, ACPI thermal trip point state changed [ 21.343390] Please send acpidump to linux-acpi@vger.kernel.org [ 21.343506] [20070126] [ 21.343558] Checking invalid active[1] trip point... [ 24.736866] pnp: the driver 'i8042 kbd' has been registered [ 24.736921] i8042 kbd 00:08: driver attached [ 24.736963] pnp: the driver 'i8042 aux' has been registered [ 24.736990] i8042 aux 00:07: driver attached [ 24.737026] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 24.740242] i8042.c: Detected active multiplexing controller, rev 1.1. [ 24.741655] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 24.748167] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 24.748522] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 24.748580] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 24.748638] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 24.775180] input: AT Translated Set 2 keyboard as /class/input/input5 [ 25.099613] powernow-k8: Found 1 Mobile AMD Sempron(tm) Processor 2600+ processors (1 cpu cores) (version 2.20.00) [ 25.108125] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6 [ 25.108189] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18 [ 25.117568] powernow-k8: ph2 null fid transition 0x8 [ 25.245082] input: PS/2 Mouse as /class/input/input6 [ 25.268164] input: AlpsPS/2 ALPS GlidePoint as /class/input/input7 [ 25.380169] Linux agpgart interface v0.103 [ 25.541038] [drm] Initialized drm 1.1.0 20060810 [ 25.578665] mice: PS/2 mouse device common for all mice [ 25.656064] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 25.657015] [drm] Initialized via 2.11.1 20070202 on minor 0 [ 25.708000] leds_clevo_mail: 'Clevo D410J' found [ 25.708413] Registered led device: clevo::mail [ 35.638131] ReiserFS: hda1: found reiserfs format "3.6" with standard journal [ 35.638225] ReiserFS: hda1: using ordered data mode [ 35.642542] ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 35.643662] ReiserFS: hda1: checking transaction log (hda1) [ 35.709971] ReiserFS: hda1: Using r5 hash to sort names [ 37.113001] ip_tables: (C) 2000-2006 Netfilter Core Team [ 37.415105] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 39.082787] NET: Registered protocol family 10 [ 45.236198] lp0: using parport0 (interrupt-driven). [ 45.259535] ppdev: user-space parallel port driver [ 46.464931] Clocksource tsc unstable (delta = -243617390 ns) [ 49.758986] eth0: no IPv6 routers present [ 52.960680] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) [ 65.452182] ACPI thermal trips update, flag is c [ 65.452198] Checking valid passive trip point... [ 65.453209] Checking valid active[0] trip point... [ 65.453296] Checking invalid active[1] trip point... [ 110.451483] ACPI thermal trips update, flag is c [ 110.451498] Checking valid passive trip point... [ 110.452470] Checking valid active[0] trip point... [ 110.452557] Checking invalid active[1] trip point... [ 112.384839] irq 16: nobody cared (try booting with the "irqpoll" option) [ 112.384839] Pid: 0, comm: swapper Not tainted 2.6.25-rc4 #6 [ 112.384839] [] __report_bad_irq+0x27/0x90 [ 112.384839] [] note_interrupt+0x236/0x270 [ 112.384839] [] ? handle_IRQ_event+0x53/0x60 [ 112.384839] [] handle_fasteoi_irq+0x7a/0xd0 [ 112.384839] [] do_IRQ+0x44/0xa0 [ 112.384839] [] common_interrupt+0x2e/0x34 [ 112.384839] [] ? _spin_unlock_irq+0x28/0x50 [ 112.384839] [] finish_task_switch+0x54/0xc0 [ 112.384839] [] ? finish_task_switch+0x0/0xc0 [ 112.384839] [] schedule+0x2b6/0x470 [ 112.384839] [] ? acpi_processor_idle+0x0/0x436 [processor] [ 112.384839] [] cpu_idle+0xb5/0xd0 [ 112.384839] [] rest_init+0x5c/0x60 [ 112.384839] ======================= [ 112.384839] handlers: [ 112.384839] [] (yenta_interrupt+0x0/0xe0 [yenta_socket]) [ 112.384839] [] (via_driver_irq_handler+0x0/0x1c0 [via]) [ 112.384839] Disabling IRQ #16