Message-ID: <20080309215748.GC15058@motherbox.xtech.com.ar>
Date:	Sun, 9 Mar 2008 19:57:48 -0200
From:	Diego Woitasen <diego@...tasen.com.ar>
To:	Thomas Gleixner <tglx@...utronix.de>
Cc:	Pavel Machek <pavel@....cz>, LKML <linux-kernel@...r.kernel.org>,
	Ingo Molnar <mingo@...e.hu>,
	Venkatesch Pallipadi <venkatesh.pallipadi@...el.com>
Subject: Re: BUG: High resolution timer/dynticks bug

On Sun, Mar 09, 2008 at 08:42:21PM +0100, Thomas Gleixner wrote:
> On Sun, 9 Mar 2008, Diego Woitasen wrote:
> > On Sun, Mar 09, 2008 at 04:42:05PM +0100, Thomas Gleixner wrote:
> > > On Sat, 8 Mar 2008, Diego Woitasen wrote:
> > > > > 
> > > > > Is the problem reproducible when you add "hpet=disable" to the kernel
> > > > > command line ?
> > > > 
> > > > No, with hpet=disable works fine.
> > > 
> > > Can you please try "processor.max_cstate=2" on the kernel command line ?
> > > 
> > > Also please provide a full boot log and the output of lspci -vvv
> > > 
> > > Thanks,
> > > 
> > > 	tglx
> > 
> > I tried. Same results, freezes after few minutes.
> > 
> > ----------------dmesg:
> 
> > Unknown boot option `processor.max_cstate=2': ignoring
> 
> Hmm. That probably does not work when the ACPI processor stuff is
> compiled as module. Can you please compile that in via
> CONFIG_ACPI_PROCESSOR=y ?
> 
> Thanks,
> 	tglx

I change the configuration and then boot with "processor.max_cstate=2",
but the system freezes again.

dmesg updated:

Linux version 2.6.25-rc4-porti-funca-00134-g84c6f60 (diegows@...ti) (gcc version 4.2.3 (Debian 4.2.3-1)) #42 PREEMPT Sun Mar 9 18:45:00 ARST 2008
Command line: root=/dev/sda2 ro nmi_watchdog=2 netconsole=4444@....168.1.101/eth0,5555@....168.1.10/00:0e:a6:b1:7e:92 processor.max_cstate=2
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
 BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001df10000 (usable)
 BIOS-e820: 000000001df10000 - 000000001df18000 (ACPI data)
 BIOS-e820: 000000001df18000 - 000000001df80000 (ACPI NVS)
 BIOS-e820: 000000001df80000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Entering add_active_range(0, 0, 157) 0 entries of 256 used
Entering add_active_range(0, 256, 122640) 1 entries of 256 used
end_pfn_map = 1048576
DMI present.
ACPI: RSDP 000F87B0, 0024 (r3 HPQOEM)
ACPI: XSDT 1DF11044, 005C (r1 HPQOEM SLIC-MPC  6040000  LTP        0)
ACPI: FACP 1DF17B21, 00F4 (r3 HPQOEM SLIC-MPC  6040000 PTL     F4240)
ACPI: DSDT 1DF110A0, 6A81 (r1 HPQOEM SLIC-MPC  6040000 MSFT  100000E)
ACPI: FACS 1DF18FC0, 0040
ACPI: SLIC 1DF17C89, 0176 (r1 HPQOEM SLIC-MPC  6040000 HPQ         1)
ACPI: MCFG 1DF17DFF, 003C (r1 HPQOEM SLIC-MPC  6040000  LTP        0)
ACPI: HPET 1DF17E3B, 0038 (r1 HPQOEM SLIC-MPC  6040000  LTP        1)
ACPI: APIC 1DF17E73, 0050 (r1 HPQOEM SLIC-MPC  6040000  LTP        0)
ACPI: BOOT 1DF17EC3, 0028 (r1 HPQOEM SLIC-MPC  6040000  LTP        1)
ACPI: SSDT 1DF17EEB, 0115 (r1 HPQOEM SLIC-MPC  6040000  LTP        1)
ACPI: DMI detected: Hewlett-Packard
Entering add_active_range(0, 0, 157) 0 entries of 256 used
Entering add_active_range(0, 256, 122640) 1 entries of 256 used
early res: 0 [0-fff] BIOS data page
early res: 1 [200000-688a07] TEXT DATA BSS
early res: 2 [9dc00-9fbff] EBDA
early res: 3 [8000-afff] PGTABLE
 [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
 [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001600000 on node 0
 [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001a00000 on node 0
 [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001e00000 on node 0
Zone PFN ranges:
  DMA             0 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1048576
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0:        0 ->      157
    0:      256 ->   122640
On node 0 totalpages: 122541
  DMA zone: 56 pages used for memmap
  DMA zone: 1168 pages reserved
  DMA zone: 2773 pages, LIFO batch:0
  DMA32 zone: 1620 pages used for memmap
  DMA32 zone: 116924 pages, LIFO batch:31
  Normal zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
Detected use of extended apic ids on hypertransport bus
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
ACPI: HPET id: 0x10de8201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
PM: Registered nosave memory: 000000000009d000 - 000000000009e000
PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000
PM: Registered nosave memory: 00000000000d2000 - 0000000000100000
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 119697
Kernel command line: root=/dev/sda2 ro nmi_watchdog=2 netconsole=4444@....168.1.101/eth0,5555@....168.1.10/00:0e:a6:b1:7e:92 processor.max_cstate=2
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 16384 bytes)
Extended CMOS year: 2000
TSC calibrated against PM_TIMER
time.c: Detected 2009.145 MHz processor.
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Checking aperture...
Node 0: aperture @ b1f8000000 size 32 MB
Aperture beyond 4GB. Ignoring.
No AGP bridge found
Memory: 475804k/490560k available (3008k kernel code, 13704k reserved, 1073k data, 204k init)
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 4020.77 BogoMIPS (lpj=2010389)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Turion(tm) 64  stepping 02
ACPI: Core revision 20070126
Using local APIC timer interrupts.
APIC timer calibration result 12557155
Detected 12.557 MHz APIC timer.
Testing NMI watchdog ... OK.
net_namespace: 872 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - e02fffff
PCI: Using configuration type 1
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x1, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.XVR2._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LK1E] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [LK2E] (IRQs 19) *11
ACPI: PCI Interrupt Link [LK3E] (IRQs 21) *10
ACPI: PCI Interrupt Link [LK4E] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 16 17 18 19 20 21 22 23) *10
ACPI: PCI Interrupt Link [LSMU] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUS0] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LUS2] (IRQs 16 17 18 19 20 21 22 23) *7
ACPI: PCI Interrupt Link [LMAC] (IRQs 16 17 18 19 20 21 22 23) *11
ACPI: PCI Interrupt Link [LAZA] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LPID] (IRQs 16 17 18 19 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 16 17 18 19 20 21 22 23) *5
ACPI: PCI Interrupt Link [LSI1] (IRQs 16 17 18 19 20 21 22 23) *0
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
Time: tsc clocksource has been installed.
system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1080-0x10ff has been reserved
system 00:02: ioport range 0x1400-0x147f has been reserved
system 00:02: ioport range 0x1480-0x14ff has been reserved
system 00:02: ioport range 0x1800-0x187f has been reserved
system 00:02: ioport range 0x1880-0x18ff has been reserved
system 00:02: ioport range 0x2000-0x203f has been reserved
system 00:03: ioport range 0x360-0x361 has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:02.0
  IO window: disabled.
  MEM window: 0xc3000000-0xc30fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: 4000-4fff
  MEM window: 0xc8000000-0xc87fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:10.0
  IO window: disabled.
  MEM window: 0xc3100000-0xc31fffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:10.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 3, 32768 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
Total HugeTLB memory allocated, 0
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler cfq registered (default)
pci 0000:00:00.0: Enabling HT MSI Mapping
pci 0000:00:02.0: Enabling HT MSI Mapping
pci 0000:00:03.0: Enabling HT MSI Mapping
pci 0000:00:05.0: Boot video device
pci 0000:00:09.0: Enabling HT MSI Mapping
pci 0000:00:0e.0: Enabling HT MSI Mapping
pci 0000:00:10.0: Enabling HT MSI Mapping
pci 0000:00:10.1: Enabling HT MSI Mapping
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie03]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
ACPI: AC Adapter [ADP1] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID0]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI: processor limited to max C-state 2
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [TZS0] (58 C)
ACPI: LNXTHERM:02 is registered as thermal_zone1
ACPI: Thermal Zone [TZS1] (61 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.103
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 23 (level, high) -> IRQ 23
PCI: Setting latency timer of device 0000:00:14.0 to 64
Switched to high resolution mode on CPU 0
forcedeth 0000:00:14.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:16:d3:91:30:79
forcedeth 0000:00:14.0: highdma pwrctl timirq lnktim desc-v3
netconsole: local port 4444
netconsole: local IP 192.168.1.101
netconsole: interface eth0
netconsole: remote port 5555
netconsole: remote IP 192.168.1.10
netconsole: remote ethernet address 00:0e:a6:b1:7e:92
netconsole: device eth0 not up yet, forcing it
eth0: no link during initialization.
netconsole: timeout waiting for carrier
console [netcon0] enabled
netconsole: network logging started
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP51: 0000:00:0d.0 (rev f1) UDMA133 controller
NFORCE-MCP51: IDE controller (0x10de:0x0265 rev 0xf1) at  PCI slot 0000:00:0d.0
NFORCE-MCP51: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x3080-0x3087, BIOS settings: hda:PIO, hdb:PIO
    ide1: BM-DMA at 0x3088-0x308f, BIOS settings: hdc:PIO, hdd:PIO
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: Slimtype DVD A DS8AZH, ATAPI CD/DVD-ROM drive
hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hdc: MWDMA2 mode selected
ide1 at 0x170-0x177,0x376 on irq 15
isa bounce pool size: 16 pages
Probing IDE interface ide0...
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Driver 'sd' needs updating - please use bus_type methods
sata_nv 0000:00:0e.0: version 3.5
PCI: Enabling device 0000:00:0e.0 (0005 -> 0007)
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LTID] -> GSI 22 (level, high) -> IRQ 22
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x30b0 ctl 0x30a4 bmdma 0x3090 irq 22
ata2: SATA max UDMA/133 cmd 0x30a8 ctl 0x30a0 bmdma 0x3098 irq 22
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: WDC WD1200BEVS-60LAT0, 01.06M01, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48 
ata1.00: configured for UDMA/100
ata2: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      WDC WD1200BEVS-6 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
input: AT Translated Set 2 keyboard as /class/input/input4
cpuidle: using governor menu
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
IPVS: ipvs loaded.
NET: Registered protocol family 1
NET: Registered protocol family 17
can: controller area network core (rev 20071116 abi 8)
NET: Registered protocol family 29
powernow-k8: Found 1 AMD Turion(tm) 64  processors (1 cpu cores) (version 2.20.00)
powernow-k8:    0 : fid 0xc (2000 MHz), vid 0xe
powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x10
powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x12
powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x18
XFS mounting filesystem sda2
Starting XFS recovery on filesystem: sda2 (logdev: internal)
Ending XFS recovery on filesystem: sda2 (logdev: internal)
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
ACPI: PCI Interrupt Link [LK2E] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LK2E] -> GSI 19 (level, high) -> IRQ 19
PCI: Setting latency timer of device 0000:01:00.0 to 64
ssb: Sonics Silicon Backplane found on PCI device 0000:01:00.0
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUS0] -> GSI 21 (level, high) -> IRQ 21
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 21, io mem 0xc0004000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@...ux.intel.com>
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.25-rc4-porti-funca-00134-g84c6f60 ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUS2] -> GSI 20 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 20, io mem 0xc0005000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
bcm43xx driver
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.25-rc4-porti-funca-00134-g84c6f60 ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
ACPI: PCI Interrupt 0000:03:09.0[A] -> Link [LNK1] -> GSI 18 (level, high) -> IRQ 18
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[c3100000-c31007ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
sdhci: SDHCI controller found at 0000:03:09.1 [1180:0822] (rev 19)
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:03:09.1[B] -> Link [LNK2] -> GSI 17 (level, high) -> IRQ 17
sdhc0:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
mmc0: SDHCI at 0xc3100800 irq 17 DMA
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 16
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 16 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:10.1 to 64
b43-phy0: Broadcom 4311 WLAN found
phy0: Selected rate control algorithm 'pid'
input: ImPS/2 Synaptics TouchPad as /class/input/input5
Broadcom 43xx driver loaded [ Features: P, Firmware-ID: FW13 ]
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[07e40a00f6cb5006]
Adding 987956k swap on /dev/sda5.  Priority:-1 extents:1 across:987956k
loop: module loaded
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@...hat.com
Ebtables v2.0 registered
Bridge firewalling registered
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Filesystem "dm-0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-0
Starting XFS recovery on filesystem: dm-0 (logdev: internal)
Ending XFS recovery on filesystem: dm-0 (logdev: internal)
Filesystem "dm-1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-1
Ending clean XFS mount for filesystem: dm-1
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
Marking TSC unstable due to TSC halts in idle
Time: hpet clocksource has been installed.
atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
atkbd.c: Unknown key released (translated set 2, code 0xd9 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:e0:4c:fe:41:e1
wlan0: RX authentication from 00:e0:4c:fe:41:e1 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:e0:4c:fe:41:e1
wlan0: RX AssocResp from 00:e0:4c:fe:41:e1 (capab=0x411 status=0 aid=193)
wlan0: invalid aid value 193; bits 15:14 not set
wlan0: associated
wlan0: switched to long barker preamble (BSSID=00:e0:4c:fe:41:e1)
TCP veno registered
-- 

--------------
Diego Woitasen
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists