Linux version 2.6.25-rc9 (christoph@stapp) (gcc version 4.2.3 20071014 (prerelease) (Debian 4.2.2-3)) #2 SMP Tue Apr 15 22:00:45 UTC 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009d000 (usable) BIOS-e820: 000000000009d000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 00000000000d8000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000cff60000 (usable) BIOS-e820: 00000000cff60000 - 00000000cff69000 (ACPI data) BIOS-e820: 00000000cff69000 - 00000000cff80000 (ACPI NVS) BIOS-e820: 00000000cff80000 - 00000000d0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000230000000 (usable) Warning only 896MB will be used. Use a HIGHMEM64G enabled kernel. 896MB LOWMEM available. Scan SMP from c0000000 for 1024 bytes. Scan SMP from c009fc00 for 1024 bytes. Scan SMP from c00f0000 for 65536 bytes. found SMP MP-table at [c00f6050] 000f6050 NX (Execute Disable) protection: active Entering add_active_range(0, 0, 229376) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 229376 On node 0 totalpages: 229376 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI present. ACPI: RSDP 000F6020, 0014 (r0 PTLTD ) ACPI: RSDT CFF64805, 0040 (r1 PTLTD RSDT 6040000 LTP 0) ACPI: FACP CFF68DD8, 0074 (r1 INTEL TUMWATER 6040000 PTL 3) ACPI: DSDT CFF65C31, 31A7 (r1 Intel BLAKFORD 6040000 MSFT 100000E) ACPI: FACS CFF69FC0, 0040 ACPI: APIC CFF68E4C, 00C8 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG CFF68F14, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: HPET CFF68F50, 0038 (r1 PTLTD HPETTBL 6040000 LTP 1) ACPI: BOOT CFF68F88, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1) ACPI: SPCR CFF68FB0, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1) ACPI: SSDT CFF64845, 13EC (r1 PmRef CpuPm 3000 INTL 20050228) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled) Processor #4 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled) Processor #5 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled) Processor #2 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled) Processor #6 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) Processor #3 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) Processor #7 6:15 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24]) IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 2 I/O APICs ACPI: HPET id: 0x8086a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at d1000000 (gap: d0000000:10000000) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227584 Kernel command line: root=/dev/sda7 console=ttyS0,38400 mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) mapped IOAPIC to ffff9000 (fec80000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2327.594 MHz processor. Console: colour VGA+ 80x25 console [ttyS0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 904008k/917504k available (2508k kernel code, 13040k reserved, 780k data, 252k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB) vmalloc : 0xf8800000 - 0xfffb3000 ( 119 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc053d000 - 0xc057c000 ( 252 kB) .data : 0xc0473192 - 0xc05364c0 ( 780 kB) .text : 0xc0200000 - 0xc0473192 (2508 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=8, Nodes=1 hpet clockevent registered Calibrating delay using timer specific routine.. 4658.45 BogoMIPS (lpj=9316916) Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. using mwait in idle threads. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 11k freed ACPI: Core revision 20070126 CPU0: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 1/1 ip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4655.01 BogoMIPS (lpj=9310023) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 2/2 ip 2000 Initializing CPU#2 Calibrating delay using timer specific routine.. 4655.04 BogoMIPS (lpj=9310097) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 3/3 ip 2000 Initializing CPU#3 Calibrating delay using timer specific routine.. 4655.05 BogoMIPS (lpj=9310100) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 4/4 ip 2000 Initializing CPU#4 Calibrating delay using timer specific routine.. 4655.09 BogoMIPS (lpj=9310182) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#4. CPU4: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 5/5 ip 2000 Initializing CPU#5 Calibrating delay using timer specific routine.. 4655.07 BogoMIPS (lpj=9310142) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#5. CPU5: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 6/6 ip 2000 Initializing CPU#6 Calibrating delay using timer specific routine.. 4655.08 BogoMIPS (lpj=9310165) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 2 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#6. CPU6: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Booting processor 7/7 ip 2000 Initializing CPU#7 Calibrating delay using timer specific routine.. 4655.08 BogoMIPS (lpj=9310171) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 1 CPU: Processor Core ID: 3 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#7. CPU7: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping 07 Total of 8 processors activated (37243.89 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. checking TSC synchronization [CPU#0 -> CPU#2]: passed. checking TSC synchronization [CPU#0 -> CPU#3]: passed. checking TSC synchronization [CPU#0 -> CPU#4]: passed. checking TSC synchronization [CPU#0 -> CPU#5]: passed. checking TSC synchronization [CPU#0 -> CPU#6]: passed. checking TSC synchronization [CPU#0 -> CPU#7]: passed. Brought up 8 CPUs CPU0 attaching sched-domain: domain 0: span 03 groups: 01 02 domain 1: span ff groups: 03 0c 30 c0 CPU1 attaching sched-domain: domain 0: span 03 groups: 02 01 domain 1: span ff groups: 03 0c 30 c0 CPU2 attaching sched-domain: domain 0: span 0c groups: 04 08 domain 1: span ff groups: 0c 30 c0 03 CPU3 attaching sched-domain: domain 0: span 0c groups: 08 04 domain 1: span ff groups: 0c 30 c0 03 CPU4 attaching sched-domain: domain 0: span 30 groups: 10 20 domain 1: span ff groups: 30 c0 03 0c CPU5 attaching sched-domain: domain 0: span 30 groups: 20 10 domain 1: span ff groups: 30 c0 03 0c CPU6 attaching sched-domain: domain 0: span c0 groups: 40 80 domain 1: span ff groups: c0 03 0c 30 CPU7 attaching sched-domain: domain 0: span c0 groups: 80 40 domain 1: span ff groups: c0 03 0c 30 net_namespace: 164 bytes NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG for extended config space PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2.BMD0.BPD2._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 *7 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 11 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active) 00:01: calling quirk 0xc0388df0: quirk_system_pci_resources+0x0/0x270() pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active) pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active) pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active) pnp 00:06: Plug and Play ACPI device, IDs PNP0800 (active) pnp 00:07: Plug and Play ACPI device, IDs INT0800 (active) pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active) pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active) pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 3 Switched to high resolution mode on CPU 6 Switched to high resolution mode on CPU 2 Switched to high resolution mode on CPU 5 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 4 Switched to high resolution mode on CPU 7 pnp: the driver 'system' has been registered system 00:01: ioport range 0x4d0-0x4d1 has been reserved system 00:01: ioport range 0x295-0x296 has been reserved system 00:01: ioport range 0xca2-0xca3 has been reserved system 00:01: ioport range 0xca8-0xcaf has been reserved system 00:01: ioport range 0x1000-0x107f has been reserved system 00:01: ioport range 0x1180-0x11bf has been reserved system 00:01: ioport range 0x800-0x80f has been reserved system 00:01: ioport range 0xfe00-0xfe00 has been reserved system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved system 00:01: iomem range 0xfee00000-0xfee0ffff could not be reserved system 00:01: iomem range 0xfec80000-0xfec80fff has been reserved system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:01: iomem range 0xfe000000-0xfe01ffff has been reserved system 00:01: iomem range 0xfe600000-0xfe6fffff has been reserved system 00:01: driver attached PCI: Bridge: 0000:02:00.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:02:02.0 IO window: 2000-2fff MEM window: 0xd8a00000-0xd8afffff PREFETCH window: disabled. PCI: Bridge: 0000:01:00.0 IO window: 2000-2fff MEM window: 0xd8a00000-0xd8afffff PREFETCH window: disabled. PCI: Bridge: 0000:01:00.3 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:02.0 IO window: 2000-2fff MEM window: 0xd8900000-0xd8afffff PREFETCH window: disabled. PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: 0xd8800000-0xd88fffff PREFETCH window: 0x00000000d8000000-0x00000000d87fffff PCI: Bridge: 0000:00:06.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: 3000-3fff MEM window: 0xd8b00000-0xd8bfffff PREFETCH window: 0x00000000d0000000-0x00000000d7ffffff ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:02.0 to 64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:02:00.0 to 64 ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:02:02.0 to 64 PCI: Setting latency timer of device 0000:01:00.3 to 64 ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:04.0 to 64 ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:06.0 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x36 set to 0x80 SGI XFS with ACLs, security attributes, realtime, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:08:01.0: Boot video device PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie01] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] PCI: Setting latency timer of device 0000:01:00.0 to 64 Allocate Port Service[0000:01:00.0:pcie11] PCI: Setting latency timer of device 0000:02:00.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:00.0:pcie21] PCI: Setting latency timer of device 0000:02:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:02:02.0:pcie21] AER service couldn't init device 0000:00:02.0:pcie01 - no _OSC support AER service couldn't init device 0000:00:04.0:pcie01 - no _OSC support AER service couldn't init device 0000:00:06.0:pcie01 - no _OSC support Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Linux agpgart interface v0.103 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A pnp: the driver 'serial' has been registered 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial 00:08: driver attached 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial 00:09: driver attached brd: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:04:00.0 to 64 e1000: 0000:04:00.0: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:79:73:86 e1000: 0000:04:00.0: e1000_probe: This device (id 8086:1096) will no longer be supported by this driver in the future. e1000: 0000:04:00.0: e1000_probe: please use the "e1000e" driver instead. e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:04:00.1 to 64 e1000: 0000:04:00.1: e1000_probe: (PCI Express:2.5Gb/s:Width x4) 00:30:48:79:73:87 e1000: 0000:04:00.1: e1000_probe: This device (id 8086:1096) will no longer be supported by this driver in the future. e1000: 0000:04:00.1: e1000_probe: please use the "e1000e" driver instead. e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection Driver 'sd' needs updating - please use bus_type methods ahci 0000:00:1f.2: version 3.0 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata1: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00500 irq 19 ata2: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00580 irq 19 ata3: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00600 irq 19 ata4: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00680 irq 19 ata5: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00700 irq 19 ata6: SATA max UDMA/133 abar m1024@0xd8e00400 port 0xd8e00780 irq 19 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: HDT722525DLA380, V44OA80A, max UDMA/133 ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA HDT722525DLA380 V44O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 sda7 > sda4 sd 0:0:0:0: [sda] Attached SCSI disk pnp: the driver 'i8042 kbd' has been registered pnp: the driver 'i8042 aux' has been registered pnp: the driver 'i8042 kbd' has been unregistered pnp: the driver 'i8042 aux' has been unregistered PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Starting balanced_irq Using IPI Shortcut mode kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 252k freed ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: ACPI0007:01 is registered as cooling_device1 ACPI: Processor [CPU1] (supports 8 throttling states) ACPI: ACPI0007:02 is registered as cooling_device2 ACPI: Processor [CPU2] (supports 8 throttling states) ACPI: ACPI0007:03 is registered as cooling_device3 ACPI: Processor [CPU3] (supports 8 throttling states) ACPI: ACPI0007:04 is registered as cooling_device4 ACPI: Processor [CPU4] (supports 8 throttling states) ACPI: ACPI0007:05 is registered as cooling_device5 ACPI: Processor [CPU5] (supports 8 throttling states) intel_rng: FWH not detected ACPI: ACPI0007:06 is registered as cooling_device6 ACPI: Processor [CPU6] (supports 8 throttling states) ACPI: ACPI0007:07 is registered as cooling_device7 ACPI: Processor [CPU7] (supports 8 throttling states) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) iTCO_wdt: Found a 631xESB/632xESB TCO device (Version=2, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) Adding 9775512k swap on /dev/sda6. Priority:-1 extents:1 across:9775512k EXT3 FS on sda7, internal journal e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX e1000: eth0: e1000_watchdog: 10/100 speed: disabling TSO