| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20080417201410.GB31616@Krystal>
Date: Thu, 17 Apr 2008 16:14:10 -0400
From: Mathieu Desnoyers <compudj@...stal.dyndns.org>
To: mingo@...e.hu
Cc: akpm@...l.org, "H. Peter Anvin" <hpa@...or.com>,
Jeremy Fitzhardinge <jeremy@...p.org>,
Steven Rostedt <rostedt@...dmis.org>,
"Frank Ch. Eigler" <fche@...hat.com>, linux-kernel@...r.kernel.org
Subject: [RFC PATCH] x86 NMI-safe INT3 and Page Fault (v5)
(hopefully finally CCing LKML) :)
Implements an alternative iret with popf and return so trap and exception
handlers can return to the NMI handler without issuing iret. iret would cause
NMIs to be reenabled prematurely. x86_32 uses popf and far return. x86_64 has to
copy the return instruction pointer to the top of the previous stack, issue a
popf, loads the previous esp and issue a near return (ret).
It allows placing immediate values (and therefore optimized trace_marks) in NMI
code since returning from a breakpoint would be valid. Accessing vmalloc'd
memory, which allows executing module code or accessing vmapped or vmalloc'd
areas from NMI context, would also be valid. This is very useful to tracers like
LTTng.
This patch makes all faults, traps and exception safe to be called from NMI
context *except* single-stepping, which requires iret to restore the TF (trap
flag) and jump to the return address in a single instruction. Sorry, no kprobes
support in NMI handlers because of this limitation. We cannot single-step an
NMI handler, because iret must set the TF flag and return back to the
instruction to single-step in a single instruction. This cannot be emulated with
popf/lret, because lret would be single-stepped. It does not apply to immediate
values because they do not use single-stepping. This code detects if the TF
flag is set and uses the iret path for single-stepping, even if it reactivates
NMIs prematurely.
alpha and avr32 use the active count bit 31. This patch moves them to 28.
TODO : test alpha and avr32 active count modification
TODO : add paravirt support for the iret alternative. Currently, paravirt
kernels running on bare metal still use iret in traps nested over nmi handlers.
tested on x86_32 (tests implemented in a separate patch) :
- instrumented the return path to export the EIP, CS and EFLAGS values when
taken so we know the return path code has been executed.
- trace_mark, using immediate values, with 10ms delay with the breakpoint
activated. Runs well through the return path.
- tested vmalloc faults in NMI handler by placing a non-optimized marker in the
NMI handler (so no breakpoint is executed) and connecting a probe which
touches every pages of a 20MB vmalloc'd buffer. It executes trough the return
path without problem.
- Tested with and without preemption
tested on x86_64
- instrumented the return path to export the EIP, CS and EFLAGS values when
taken so we know the return path code has been executed.
- trace_mark, using immediate values, with 10ms delay with the breakpoint
activated. Runs well through the return path.
To test on x86_64 :
- Test without preemption
- Test vmalloc faults
- Test on Intel 64 bits CPUs.
Changelog since v1 :
- x86_64 fixes.
Changelog since v2 :
- fix paravirt build
Changelog since v3 :
- Include modifications suggested by Jeremy
Changelog since v3 :
- including hardirq.h in entry_32/64.S is a bad idea (non ifndef'd C
code), define HARDNMI_MASK in the .S files directly.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@...ymtl.ca>
CC: akpm@...l.org
CC: mingo@...e.hu
CC: "H. Peter Anvin" <hpa@...or.com>
CC: Jeremy Fitzhardinge <jeremy@...p.org>
CC: Steven Rostedt <rostedt@...dmis.org>
CC: "Frank Ch. Eigler" <fche@...hat.com>
---
arch/x86/kernel/entry_32.S | 27 ++++++++++++++++++-
arch/x86/kernel/entry_64.S | 26 ++++++++++++++++++
include/asm-alpha/thread_info.h | 2 -
include/asm-avr32/thread_info.h | 2 -
include/asm-x86/irqflags.h | 55 ++++++++++++++++++++++++++++++++++++++++
include/asm-x86/paravirt.h | 2 +
include/linux/hardirq.h | 24 ++++++++++++++++-
7 files changed, 133 insertions(+), 5 deletions(-)
Index: linux-2.6-lttng/include/linux/hardirq.h
===================================================================
--- linux-2.6-lttng.orig/include/linux/hardirq.h 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/include/linux/hardirq.h 2008-04-16 11:29:30.000000000 -0400
@@ -22,10 +22,13 @@
* PREEMPT_MASK: 0x000000ff
* SOFTIRQ_MASK: 0x0000ff00
* HARDIRQ_MASK: 0x0fff0000
+ * HARDNMI_MASK: 0x40000000
*/
#define PREEMPT_BITS 8
#define SOFTIRQ_BITS 8
+#define HARDNMI_BITS 1
+
#ifndef HARDIRQ_BITS
#define HARDIRQ_BITS 12
@@ -45,16 +48,19 @@
#define PREEMPT_SHIFT 0
#define SOFTIRQ_SHIFT (PREEMPT_SHIFT + PREEMPT_BITS)
#define HARDIRQ_SHIFT (SOFTIRQ_SHIFT + SOFTIRQ_BITS)
+#define HARDNMI_SHIFT (30)
#define __IRQ_MASK(x) ((1UL << (x))-1)
#define PREEMPT_MASK (__IRQ_MASK(PREEMPT_BITS) << PREEMPT_SHIFT)
#define SOFTIRQ_MASK (__IRQ_MASK(SOFTIRQ_BITS) << SOFTIRQ_SHIFT)
#define HARDIRQ_MASK (__IRQ_MASK(HARDIRQ_BITS) << HARDIRQ_SHIFT)
+#define HARDNMI_MASK (__IRQ_MASK(HARDNMI_BITS) << HARDNMI_SHIFT)
#define PREEMPT_OFFSET (1UL << PREEMPT_SHIFT)
#define SOFTIRQ_OFFSET (1UL << SOFTIRQ_SHIFT)
#define HARDIRQ_OFFSET (1UL << HARDIRQ_SHIFT)
+#define HARDNMI_OFFSET (1UL << HARDNMI_SHIFT)
#if PREEMPT_ACTIVE < (1 << (HARDIRQ_SHIFT + HARDIRQ_BITS))
#error PREEMPT_ACTIVE is too low!
@@ -63,6 +69,7 @@
#define hardirq_count() (preempt_count() & HARDIRQ_MASK)
#define softirq_count() (preempt_count() & SOFTIRQ_MASK)
#define irq_count() (preempt_count() & (HARDIRQ_MASK | SOFTIRQ_MASK))
+#define hardnmi_count() (preempt_count() & HARDNMI_MASK)
/*
* Are we doing bottom half or hardware interrupt processing?
@@ -71,6 +78,7 @@
#define in_irq() (hardirq_count())
#define in_softirq() (softirq_count())
#define in_interrupt() (irq_count())
+#define in_nmi() (hardnmi_count())
/*
* Are we running in atomic context? WARNING: this macro cannot
@@ -159,7 +167,19 @@ extern void irq_enter(void);
*/
extern void irq_exit(void);
-#define nmi_enter() do { lockdep_off(); __irq_enter(); } while (0)
-#define nmi_exit() do { __irq_exit(); lockdep_on(); } while (0)
+#define nmi_enter() \
+ do { \
+ lockdep_off(); \
+ BUG_ON(hardnmi_count()); \
+ add_preempt_count(HARDNMI_OFFSET); \
+ __irq_enter(); \
+ } while (0)
+
+#define nmi_exit() \
+ do { \
+ __irq_exit(); \
+ sub_preempt_count(HARDNMI_OFFSET); \
+ lockdep_on(); \
+ } while (0)
#endif /* LINUX_HARDIRQ_H */
Index: linux-2.6-lttng/arch/x86/kernel/entry_32.S
===================================================================
--- linux-2.6-lttng.orig/arch/x86/kernel/entry_32.S 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/arch/x86/kernel/entry_32.S 2008-04-17 12:55:10.000000000 -0400
@@ -75,11 +75,12 @@ DF_MASK = 0x00000400
NT_MASK = 0x00004000
VM_MASK = 0x00020000
+#define HARDNMI_MASK 0x40000000
+
#ifdef CONFIG_PREEMPT
#define preempt_stop(clobbers) DISABLE_INTERRUPTS(clobbers); TRACE_IRQS_OFF
#else
#define preempt_stop(clobbers)
-#define resume_kernel restore_nocheck
#endif
.macro TRACE_IRQS_IRET
@@ -265,6 +266,8 @@ END(ret_from_exception)
#ifdef CONFIG_PREEMPT
ENTRY(resume_kernel)
DISABLE_INTERRUPTS(CLBR_ANY)
+ testl $HARDNMI_MASK,TI_preempt_count(%ebp) # nested over NMI ?
+ jnz return_to_nmi
cmpl $0,TI_preempt_count(%ebp) # non-zero preempt_count ?
jnz restore_nocheck
need_resched:
@@ -276,6 +279,12 @@ need_resched:
call preempt_schedule_irq
jmp need_resched
END(resume_kernel)
+#else
+ENTRY(resume_kernel)
+ testl $HARDNMI_MASK,TI_preempt_count(%ebp) # nested over NMI ?
+ jnz return_to_nmi
+ jmp restore_nocheck
+END(resume_kernel)
#endif
CFI_ENDPROC
@@ -411,6 +420,22 @@ restore_nocheck_notrace:
CFI_ADJUST_CFA_OFFSET -4
irq_return:
INTERRUPT_RETURN
+return_to_nmi:
+ testl $X86_EFLAGS_TF, PT_EFLAGS(%esp)
+ jnz restore_nocheck /*
+ * If single-stepping an NMI handler,
+ * use the normal iret path instead of
+ * the popf/lret because lret would be
+ * single-stepped. It should not
+ * happen : it will reactivate NMIs
+ * prematurely.
+ */
+ TRACE_IRQS_IRET
+ RESTORE_REGS
+ addl $4, %esp # skip orig_eax/error_code
+ CFI_ADJUST_CFA_OFFSET -4
+ INTERRUPT_RETURN_NMI_SAFE
+
.section .fixup,"ax"
iret_exc:
pushl $0 # no error code
Index: linux-2.6-lttng/arch/x86/kernel/entry_64.S
===================================================================
--- linux-2.6-lttng.orig/arch/x86/kernel/entry_64.S 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/arch/x86/kernel/entry_64.S 2008-04-17 12:53:54.000000000 -0400
@@ -54,6 +54,8 @@
.code64
+#define HARDNMI_MASK 0x40000000
+
#ifndef CONFIG_PREEMPT
#define retint_kernel retint_restore_args
#endif
@@ -581,12 +583,27 @@ retint_restore_args: /* return to kernel
* The iretq could re-enable interrupts:
*/
TRACE_IRQS_IRETQ
+ testl $HARDNMI_MASK,threadinfo_preempt_count(%rcx)
+ jnz return_to_nmi /* Nested over NMI ? */
restore_args:
RESTORE_ARGS 0,8,0
irq_return:
INTERRUPT_RETURN
+return_to_nmi: /*
+ * If single-stepping an NMI handler,
+ * use the normal iret path instead of
+ * the popf/lret because lret would be
+ * single-stepped. It should not
+ * happen : it will reactivate NMIs
+ * prematurely.
+ */
+ testw $X86_EFLAGS_TF,EFLAGS-ARGOFFSET(%rsp) /* trap flag? */
+ jnz restore_args
+ RESTORE_ARGS 0,8,0
+ INTERRUPT_RETURN_NMI_SAFE
+
.section __ex_table, "a"
.quad irq_return, bad_iret
.previous
@@ -802,6 +819,10 @@ END(spurious_interrupt)
.macro paranoidexit trace=1
/* ebx: no swapgs flag */
paranoid_exit\trace:
+ GET_THREAD_INFO(%rcx)
+ testl $HARDNMI_MASK,threadinfo_preempt_count(%rcx)
+ jnz paranoid_return_to_nmi\trace /* Nested over NMI ? */
+paranoid_exit_no_nmi\trace:
testl %ebx,%ebx /* swapgs needed? */
jnz paranoid_restore\trace
testl $3,CS(%rsp)
@@ -814,6 +835,11 @@ paranoid_swapgs\trace:
paranoid_restore\trace:
RESTORE_ALL 8
jmp irq_return
+paranoid_return_to_nmi\trace:
+ testw $X86_EFLAGS_TF,EFLAGS-0(%rsp) /* trap flag? */
+ jnz paranoid_exit_no_nmi\trace
+ RESTORE_ALL 8
+ INTERRUPT_RETURN_NMI_SAFE
paranoid_userspace\trace:
GET_THREAD_INFO(%rcx)
movl threadinfo_flags(%rcx),%ebx
Index: linux-2.6-lttng/include/asm-x86/irqflags.h
===================================================================
--- linux-2.6-lttng.orig/include/asm-x86/irqflags.h 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/include/asm-x86/irqflags.h 2008-04-17 12:28:23.000000000 -0400
@@ -138,12 +138,67 @@ static inline unsigned long __raw_local_
#ifdef CONFIG_X86_64
#define INTERRUPT_RETURN iretq
+
+/*
+ * Only returns from a trap or exception to a NMI context (intra-privilege
+ * level near return) to the same SS and CS segments. Should be used
+ * upon trap or exception return when nested over a NMI context so no iret is
+ * issued. It takes care of modifying the eflags, rsp and returning to the
+ * previous function.
+ *
+ * The stack, at that point, looks like :
+ *
+ * 0(rsp) RIP
+ * 8(rsp) CS
+ * 16(rsp) EFLAGS
+ * 24(rsp) RSP
+ * 32(rsp) SS
+ *
+ * Upon execution :
+ * Copy EIP to the top of the return stack
+ * Update top of return stack address
+ * Pop eflags into the eflags register
+ * Make the return stack current
+ * Near return (popping the return address from the return stack)
+ */
+#define INTERRUPT_RETURN_NMI_SAFE pushq %rax; \
+ mov %rsp, %rax; \
+ mov 24+8(%rax), %rsp; \
+ pushq 0+8(%rax); \
+ pushq 16+8(%rax); \
+ movq (%rax), %rax; \
+ popfq; \
+ ret;
+
#define ENABLE_INTERRUPTS_SYSCALL_RET \
movq %gs:pda_oldrsp, %rsp; \
swapgs; \
sysretq;
#else
#define INTERRUPT_RETURN iret
+
+/*
+ * Protected mode only, no V8086. Implies that protected mode must
+ * be entered before NMIs or MCEs are enabled. Only returns from a trap or
+ * exception to a NMI context (intra-privilege level far return). Should be used
+ * upon trap or exception return when nested over a NMI context so no iret is
+ * issued.
+ *
+ * The stack, at that point, looks like :
+ *
+ * 0(esp) EIP
+ * 4(esp) CS
+ * 8(esp) EFLAGS
+ *
+ * Upon execution :
+ * Copy the stack eflags to top of stack
+ * Pop eflags into the eflags register
+ * Far return: pop EIP and CS into their register, and additionally pop EFLAGS.
+ */
+#define INTERRUPT_RETURN_NMI_SAFE pushl 8(%esp); \
+ popfl; \
+ lret $4;
+
#define ENABLE_INTERRUPTS_SYSCALL_RET sti; sysexit
#define GET_CR0_INTO_EAX movl %cr0, %eax
#endif
Index: linux-2.6-lttng/include/asm-alpha/thread_info.h
===================================================================
--- linux-2.6-lttng.orig/include/asm-alpha/thread_info.h 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/include/asm-alpha/thread_info.h 2008-04-17 12:53:55.000000000 -0400
@@ -57,7 +57,7 @@ register struct thread_info *__current_t
#endif /* __ASSEMBLY__ */
-#define PREEMPT_ACTIVE 0x40000000
+#define PREEMPT_ACTIVE 0x10000000
/*
* Thread information flags:
Index: linux-2.6-lttng/include/asm-avr32/thread_info.h
===================================================================
--- linux-2.6-lttng.orig/include/asm-avr32/thread_info.h 2008-04-16 11:25:18.000000000 -0400
+++ linux-2.6-lttng/include/asm-avr32/thread_info.h 2008-04-17 12:53:55.000000000 -0400
@@ -70,7 +70,7 @@ static inline struct thread_info *curren
#endif /* !__ASSEMBLY__ */
-#define PREEMPT_ACTIVE 0x40000000
+#define PREEMPT_ACTIVE 0x10000000
/*
* Thread information flags
Index: linux-2.6-lttng/include/asm-x86/paravirt.h
===================================================================
--- linux-2.6-lttng.orig/include/asm-x86/paravirt.h 2008-04-16 12:23:44.000000000 -0400
+++ linux-2.6-lttng/include/asm-x86/paravirt.h 2008-04-16 12:24:36.000000000 -0400
@@ -1358,6 +1358,8 @@ static inline unsigned long __raw_local_
PARA_SITE(PARA_PATCH(pv_cpu_ops, PV_CPU_iret), CLBR_NONE, \
jmp *%cs:pv_cpu_ops+PV_CPU_iret)
+#define INTERRUPT_RETURN_NMI_SAFE INTERRUPT_RETURN
+
#define DISABLE_INTERRUPTS(clobbers) \
PARA_SITE(PARA_PATCH(pv_irq_ops, PV_IRQ_irq_disable), clobbers, \
PV_SAVE_REGS; \
--
Mathieu Desnoyers
Computer Engineering Ph.D. Student, Ecole Polytechnique de Montreal
OpenPGP key fingerprint: 8CD5 52C3 8E3C 4140 715F BA06 3F25 A8FE 3BAE 9A68
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists