| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1216135490-21656-6-git-send-email-will.newton@imgtec.com>
Date: Tue, 15 Jul 2008 16:24:44 +0100
From: Will Newton <will.newton@...tec.com>
To: linux-kernel@...r.kernel.org
Cc: linux-usb@...r.kernel.org, leoli@...escale.com,
tanya.jiang@...escale.com, gregkh@...e.de,
Will Newton <will.newton@...il.com>
Subject: [PATCH 05/11] fsl_usb2_udc: Clean up whitespace in /proc debugging output.
From: Will Newton <will.newton@...il.com>
Missing spaces were causing the /proc debugging output to be rather
unreadable.
Signed-off-by: Will Newton <will.newton@...il.com>
---
drivers/usb/gadget/fsl_usb2_udc.c | 35 ++++++++++++++++++-----------------
1 files changed, 18 insertions(+), 17 deletions(-)
diff --git a/drivers/usb/gadget/fsl_usb2_udc.c b/drivers/usb/gadget/fsl_usb2_udc.c
index 18f4881..130a59d 100644
--- a/drivers/usb/gadget/fsl_usb2_udc.c
+++ b/drivers/usb/gadget/fsl_usb2_udc.c
@@ -1909,7 +1909,7 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->usbsts);
t = scnprintf(next, size,
"USB Status Reg:\n"
- "Dr Suspend: %d" "Reset Received: %d" "System Error: %s"
+ "Dr Suspend: %d Reset Received: %d System Error: %s "
"USB Error Interrupt: %s\n\n",
(tmp_reg & USB_STS_SUSPEND) ? 1 : 0,
(tmp_reg & USB_STS_RESET) ? 1 : 0,
@@ -1921,11 +1921,11 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->usbintr);
t = scnprintf(next, size,
"USB Intrrupt Enable Reg:\n"
- "Sleep Enable: %d" "SOF Received Enable: %d"
+ "Sleep Enable: %d SOF Received Enable: %d "
"Reset Enable: %d\n"
- "System Error Enable: %d"
+ "System Error Enable: %d "
"Port Change Dectected Enable: %d\n"
- "USB Error Intr Enable: %d" "USB Intr Enable: %d\n\n",
+ "USB Error Intr Enable: %d USB Intr Enable: %d\n\n",
(tmp_reg & USB_INTR_DEVICE_SUSPEND) ? 1 : 0,
(tmp_reg & USB_INTR_SOF_EN) ? 1 : 0,
(tmp_reg & USB_INTR_RESET_EN) ? 1 : 0,
@@ -1938,21 +1938,21 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->frindex);
t = scnprintf(next, size,
- "USB Frame Index Reg:" "Frame Number is 0x%x\n\n",
+ "USB Frame Index Reg: Frame Number is 0x%x\n\n",
(tmp_reg & USB_FRINDEX_MASKS));
size -= t;
next += t;
tmp_reg = fsl_readl(&dr_regs->deviceaddr);
t = scnprintf(next, size,
- "USB Device Address Reg:" "Device Addr is 0x%x\n\n",
+ "USB Device Address Reg: Device Addr is 0x%x\n\n",
(tmp_reg & USB_DEVICE_ADDRESS_MASK));
size -= t;
next += t;
tmp_reg = fsl_readl(&dr_regs->endpointlistaddr);
t = scnprintf(next, size,
- "USB Endpoint List Address Reg:"
+ "USB Endpoint List Address Reg: "
"Device Addr is 0x%x\n\n",
(tmp_reg & USB_EP_LIST_ADDRESS_MASK));
size -= t;
@@ -1961,11 +1961,12 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->portsc1);
t = scnprintf(next, size,
"USB Port Status&Control Reg:\n"
- "Port Transceiver Type : %s" "Port Speed: %s \n"
- "PHY Low Power Suspend: %s" "Port Reset: %s"
- "Port Suspend Mode: %s \n" "Over-current Change: %s"
+ "Port Transceiver Type : %s Port Speed: %s\n"
+ "PHY Low Power Suspend: %s Port Reset: %s "
+ "Port Suspend Mode: %s\n"
+ "Over-current Change: %s "
"Port Enable/Disable Change: %s\n"
- "Port Enabled/Disabled: %s"
+ "Port Enabled/Disabled: %s "
"Current Connect Status: %s\n\n", ( {
char *s;
switch (tmp_reg & PORTSCX_PTS_FSLS) {
@@ -2010,7 +2011,7 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->usbmode);
t = scnprintf(next, size,
- "USB Mode Reg:" "Controller Mode is : %s\n\n", ( {
+ "USB Mode Reg: Controller Mode is: %s\n\n", ( {
char *s;
switch (tmp_reg & USB_MODE_CTRL_MODE_HOST) {
case USB_MODE_CTRL_MODE_IDLE:
@@ -2029,7 +2030,7 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
tmp_reg = fsl_readl(&dr_regs->endptsetupstat);
t = scnprintf(next, size,
- "Endpoint Setup Status Reg:" "SETUP on ep 0x%x\n\n",
+ "Endpoint Setup Status Reg: SETUP on ep 0x%x\n\n",
(tmp_reg & EP_SETUP_STATUS_MASK));
size -= t;
next += t;
@@ -2042,12 +2043,12 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
next += t;
}
tmp_reg = fsl_readl(&dr_regs->endpointprime);
- t = scnprintf(next, size, "EP Prime Reg = [0x%x]\n", tmp_reg);
+ t = scnprintf(next, size, "EP Prime Reg = [0x%x]\n\n", tmp_reg);
size -= t;
next += t;
tmp_reg = usb_sys_regs->snoop1;
- t = scnprintf(next, size, "\nSnoop1 Reg : = [0x%x]\n\n", tmp_reg);
+ t = scnprintf(next, size, "Snoop1 Reg : = [0x%x]\n\n", tmp_reg);
size -= t;
next += t;
@@ -2071,7 +2072,7 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
} else {
list_for_each_entry(req, &ep->queue, queue) {
t = scnprintf(next, size,
- "req %p actual 0x%x length 0x%x buf %p\n",
+ "req %p actual 0x%x length 0x%x buf %p\n",
&req->req, req->req.actual,
req->req.length, req->req.buf);
size -= t;
@@ -2097,7 +2098,7 @@ static int fsl_proc_read(char *page, char **start, off_t off, int count,
} else {
list_for_each_entry(req, &ep->queue, queue) {
t = scnprintf(next, size,
- "req %p actual 0x%x length"
+ "req %p actual 0x%x length "
"0x%x buf %p\n",
&req->req, req->req.actual,
req->req.length, req->req.buf);
--
1.5.5.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists