| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 25 Jul 2008 15:53:29 +0200
From: Michal Schmidt <mschmidt@...hat.com>
To: Matthew Wilcox <matthew@....cx>
Cc: Jesse Barnes <jbarnes@...tuousgeek.org>,
David Vrabel <david.vrabel@....com>, linux-pci@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: PCI: MSI interrupts masked using prohibited method
On Fri, 25 Jul 2008 07:42:52 -0600
Matthew Wilcox <matthew@....cx> wrote:
> On Fri, Jul 25, 2008 at 03:29:18PM +0200, Michal Schmidt wrote:
> > The interesting thing is that I can see Destination ID bits of MSI
> > Message Address change correctly in lspci output. But the interrupt
> > is still delivered load-balanced to all CPUs even though the
> > Destination ID identifies the single CPU I asked for. It seems the
> > device only takes the new Message Address setting into account when
> > the MSI Enable bit in the Message Control register is changed from
> > 0 to 1. I tested this by setting the MSI enable bit to 0 and then
> > immediately back to 1 at the end of
> > io_apic_64.c:set_msi_irq_affinity().
> >
> > Is this a permitted behaviour for the device? I couldn't find
> > anything in the PCI specification that would mentioned it.
>
> I don't think that's necessary. However, the thought occurs that we
> ought to disable MSI, then write the address, then re-enable MSI. It
> doesn't cause a problem at the moment because we don't change the
> top 32 bits of the address (at least on any of my systems ..) but
> theoretically if we were to use a 64-bit address, we would experience
> MSIs being sent to an address that was a mixture of the top 32 bits of
> the old address and the bottom 32 bits of the new address.
>
> We definitely can already get tearing when we've written the lower
> address register but not the data register yet (also true for MSIX, by
> the way). So we ought to fix this properly.
>
> We have the problem that we might still get interrupts on the old
> pin-based interrupt line (ie David's original problem). I have a
> feeling somebody needs to register a handler for the pin-based
> interrupt to handle this. One possibility would be for the MSI code
> to register a handler that calls the driver's MSI handler. I don't
> think that's a good idea though -- the driver's MSI handler is able
> to make different assumptions from the pin handler. Do we want to
> make drivers register an interrupt handler for the original interrupt
> number before they try to set up MSI? It's certainly not what the
> PCI spec people had in mind, but they seem to have overlooked this
> problem.
>
> Yuck.
Maybe we should just not use MSI for devices without maskbits.
What would you think of this patch?:
This adds the parameter pci=msimaskbits to enable MSI only for devices with
maskbits. It is useful when setting of IRQ SMP affinity is needed, because
smp_affinity does not work reliably for MSI interrupts of devices without
maskbits.
And maybe this behaviour should be the default?
Michal
diff --git a/drivers/pci/msi.c b/drivers/pci/msi.c
index 15af618..2771356 100644
--- a/drivers/pci/msi.c
+++ b/drivers/pci/msi.c
@@ -23,6 +23,7 @@
#include "pci.h"
#include "msi.h"
+/* 0 = disabled, 1 = enabled, 2 = enabled only for devices with mask bits */
static int pci_msi_enable = 1;
/* Arch hooks */
@@ -356,8 +357,13 @@ static int msi_capability_init(struct pci_dev *dev)
msi_set_enable(dev, 0); /* Ensure msi is disabled as I set it up */
- pos = pci_find_capability(dev, PCI_CAP_ID_MSI);
+ pos = pci_find_capability(dev, PCI_CAP_ID_MSI);
pci_read_config_word(dev, msi_control_reg(pos), &control);
+ if (pci_msi_enable == 2 && !is_mask_bit_support(control)) {
+ dev_info(&dev->dev,
+ "does not support maskbits, will not use MSI\n");
+ return -ENODEV;
+ }
/* MSI Entry Initialization */
entry = alloc_msi_entry();
if (!entry)
@@ -749,6 +755,11 @@ void pci_no_msi(void)
pci_msi_enable = 0;
}
+void pci_msi_require_mask_bits(void)
+{
+ pci_msi_enable = 2;
+}
+
void pci_msi_init_pci_dev(struct pci_dev *dev)
{
INIT_LIST_HEAD(&dev->msi_list);
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index d00f0e0..0e6019d 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -1868,6 +1868,8 @@ static int __devinit pci_setup(char *str)
if (*str && (str = pcibios_setup(str)) && *str) {
if (!strcmp(str, "nomsi")) {
pci_no_msi();
+ } else if (!strcmp(str, "msimaskbits")) {
+ pci_msi_require_mask_bits();
} else if (!strcmp(str, "noaer")) {
pci_no_aer();
} else if (!strcmp(str, "nodomains")) {
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index d807cd7..2af4750 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -85,9 +85,11 @@ extern unsigned int pci_pm_d3_delay;
#ifdef CONFIG_PCI_MSI
void pci_no_msi(void);
+void pci_msi_require_mask_bits(void);
extern void pci_msi_init_pci_dev(struct pci_dev *dev);
#else
static inline void pci_no_msi(void) { }
+static inline void pci_msi_require_mask_bits(void) { }
static inline void pci_msi_init_pci_dev(struct pci_dev *dev) { }
#endif
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists