| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20080727011632.GF3415@pingi.kke.suse.de>
Date: Sun, 27 Jul 2008 03:16:32 +0200
From: Karsten Keil <kkeil@...e.de>
To: Linus Torvalds <torvalds@...ux-foundation.org>
Cc: linux-kernel@...r.kernel.org
Subject: [PATCH 6/7] Add mISDN HFC multiport driver
Enable support for cards with Cologne Chip AG's HFC multiport
chip.
Signed-off-by: Karsten Keil <kkeil@...e.de>
---
drivers/isdn/hardware/mISDN/Kconfig | 12 +
drivers/isdn/hardware/mISDN/Makefile | 1 +
drivers/isdn/hardware/mISDN/hfc_multi.h | 1204 +++++++
drivers/isdn/hardware/mISDN/hfcmulti.c | 5320 +++++++++++++++++++++++++++++++
include/linux/pci_ids.h | 33 +
5 files changed, 6570 insertions(+), 0 deletions(-)
create mode 100644 drivers/isdn/hardware/mISDN/hfc_multi.h
create mode 100644 drivers/isdn/hardware/mISDN/hfcmulti.c
diff --git a/drivers/isdn/hardware/mISDN/Kconfig b/drivers/isdn/hardware/mISDN/Kconfig
index f62dc87..1479348 100644
--- a/drivers/isdn/hardware/mISDN/Kconfig
+++ b/drivers/isdn/hardware/mISDN/Kconfig
@@ -11,3 +11,15 @@ config MISDN_HFCPCI
Enable support for cards with Cologne Chip AG's
HFC PCI chip.
+config MISDN_HFCMULTI
+ tristate "Support for HFC multiport cards (HFC-4S/8S/E1)"
+ depends on PCI
+ depends on MISDN
+ help
+ Enable support for cards with Cologne Chip AG's HFC multiport
+ chip. There are three types of chips that are quite similar,
+ but the interface is different:
+ * HFC-4S (4 S/T interfaces on one chip)
+ * HFC-8S (8 S/T interfaces on one chip)
+ * HFC-E1 (E1 interface for 2Mbit ISDN)
+
diff --git a/drivers/isdn/hardware/mISDN/Makefile b/drivers/isdn/hardware/mISDN/Makefile
index 6f20a40..1e7ca53 100644
--- a/drivers/isdn/hardware/mISDN/Makefile
+++ b/drivers/isdn/hardware/mISDN/Makefile
@@ -4,3 +4,4 @@
#
obj-$(CONFIG_MISDN_HFCPCI) += hfcpci.o
+obj-$(CONFIG_MISDN_HFCMULTI) += hfcmulti.o
diff --git a/drivers/isdn/hardware/mISDN/hfc_multi.h b/drivers/isdn/hardware/mISDN/hfc_multi.h
new file mode 100644
index 0000000..a33d87a
--- /dev/null
+++ b/drivers/isdn/hardware/mISDN/hfc_multi.h
@@ -0,0 +1,1204 @@
+/*
+ * see notice in hfc_multi.c
+ */
+
+extern void ztdummy_extern_interrupt(void);
+extern void ztdummy_register_interrupt(void);
+extern int ztdummy_unregister_interrupt(void);
+
+#define DEBUG_HFCMULTI_FIFO 0x00010000
+#define DEBUG_HFCMULTI_CRC 0x00020000
+#define DEBUG_HFCMULTI_INIT 0x00040000
+#define DEBUG_HFCMULTI_PLXSD 0x00080000
+#define DEBUG_HFCMULTI_MODE 0x00100000
+#define DEBUG_HFCMULTI_MSG 0x00200000
+#define DEBUG_HFCMULTI_STATE 0x00400000
+#define DEBUG_HFCMULTI_SYNC 0x01000000
+#define DEBUG_HFCMULTI_DTMF 0x02000000
+#define DEBUG_HFCMULTI_LOCK 0x80000000
+
+#define PCI_ENA_REGIO 0x01
+#define PCI_ENA_MEMIO 0x02
+
+/*
+ * NOTE: some registers are assigned multiple times due to different modes
+ * also registers are assigned differen for HFC-4s/8s and HFC-E1
+ */
+
+/*
+#define MAX_FRAME_SIZE 2048
+*/
+
+struct hfc_chan {
+ struct dchannel *dch; /* link if channel is a D-channel */
+ struct bchannel *bch; /* link if channel is a B-channel */
+ int port; /* the interface port this */
+ /* channel is associated with */
+ int nt_timer; /* -1 if off, 0 if elapsed, >0 if running */
+ int los, ais, slip_tx, slip_rx, rdi; /* current alarms */
+ int jitter;
+ u_long cfg; /* port configuration */
+ int sync; /* sync state (used by E1) */
+ u_int protocol; /* current protocol */
+ int slot_tx; /* current pcm slot */
+ int bank_tx; /* current pcm bank */
+ int slot_rx;
+ int bank_rx;
+ int conf; /* conference setting of TX slot */
+ int txpending; /* if there is currently data in */
+ /* the FIFO 0=no, 1=yes, 2=splloop */
+ int rx_off; /* set to turn fifo receive off */
+ int coeff_count; /* curren coeff block */
+ s32 *coeff; /* memory pointer to 8 coeff blocks */
+};
+
+
+struct hfcm_hw {
+ u_char r_ctrl;
+ u_char r_irq_ctrl;
+ u_char r_cirm;
+ u_char r_ram_sz;
+ u_char r_pcm_md0;
+ u_char r_irqmsk_misc;
+ u_char r_dtmf;
+ u_char r_st_sync;
+ u_char r_sci_msk;
+ u_char r_tx0, r_tx1;
+ u_char a_st_ctrl0[8];
+ timer_t timer;
+};
+
+
+/* for each stack these flags are used (cfg) */
+#define HFC_CFG_NONCAP_TX 1 /* S/T TX interface has less capacity */
+#define HFC_CFG_DIS_ECHANNEL 2 /* disable E-channel processing */
+#define HFC_CFG_REG_ECHANNEL 3 /* register E-channel */
+#define HFC_CFG_OPTICAL 4 /* the E1 interface is optical */
+#define HFC_CFG_REPORT_LOS 5 /* the card should report loss of signal */
+#define HFC_CFG_REPORT_AIS 6 /* the card should report alarm ind. sign. */
+#define HFC_CFG_REPORT_SLIP 7 /* the card should report bit slips */
+#define HFC_CFG_REPORT_RDI 8 /* the card should report remote alarm */
+#define HFC_CFG_DTMF 9 /* enable DTMF-detection */
+#define HFC_CFG_CRC4 10 /* disable CRC-4 Multiframe mode, */
+ /* use double frame instead. */
+
+#define HFC_CHIP_EXRAM_128 0 /* external ram 128k */
+#define HFC_CHIP_EXRAM_512 1 /* external ram 256k */
+#define HFC_CHIP_REVISION0 2 /* old fifo handling */
+#define HFC_CHIP_PCM_SLAVE 3 /* PCM is slave */
+#define HFC_CHIP_PCM_MASTER 4 /* PCM is master */
+#define HFC_CHIP_RX_SYNC 5 /* disable pll sync for pcm */
+#define HFC_CHIP_DTMF 6 /* DTMF decoding is enabled */
+#define HFC_CHIP_ULAW 7 /* ULAW mode */
+#define HFC_CHIP_CLOCK2 8 /* double clock mode */
+#define HFC_CHIP_E1CLOCK_GET 9 /* always get clock from E1 interface */
+#define HFC_CHIP_E1CLOCK_PUT 10 /* always put clock from E1 interface */
+#define HFC_CHIP_WATCHDOG 11 /* whether we should send signals */
+ /* to the watchdog */
+#define HFC_CHIP_B410P 12 /* whether we have a b410p with echocan in */
+ /* hw */
+#define HFC_CHIP_PLXSD 13 /* whether we have a Speech-Design PLX */
+
+#define HFC_IO_MODE_PCIMEM 0x00 /* normal memory mapped IO */
+#define HFC_IO_MODE_REGIO 0x01 /* PCI io access */
+#define HFC_IO_MODE_PLXSD 0x02 /* access HFC via PLX9030 */
+
+/* table entry in the PCI devices list */
+struct hm_map {
+ char *vendor_name;
+ char *card_name;
+ int type;
+ int ports;
+ int clock2;
+ int leds;
+ int opticalsupport;
+ int dip_type;
+ int io_mode;
+};
+
+struct hfc_multi {
+ struct list_head list;
+ struct hm_map *mtyp;
+ int id;
+ int pcm; /* id of pcm bus */
+ int type;
+ int ports;
+
+ u_int irq; /* irq used by card */
+ u_int irqcnt;
+ struct pci_dev *pci_dev;
+ int io_mode; /* selects mode */
+#ifdef HFC_REGISTER_DEBUG
+ void (*HFC_outb)(struct hfc_multi *hc, u_char reg,
+ u_char val, const char *function, int line);
+ void (*HFC_outb_nodebug)(struct hfc_multi *hc, u_char reg,
+ u_char val, const char *function, int line);
+ u_char (*HFC_inb)(struct hfc_multi *hc, u_char reg,
+ const char *function, int line);
+ u_char (*HFC_inb_nodebug)(struct hfc_multi *hc, u_char reg,
+ const char *function, int line);
+ u_short (*HFC_inw)(struct hfc_multi *hc, u_char reg,
+ const char *function, int line);
+ u_short (*HFC_inw_nodebug)(struct hfc_multi *hc, u_char reg,
+ const char *function, int line);
+ void (*HFC_wait)(struct hfc_multi *hc,
+ const char *function, int line);
+ void (*HFC_wait_nodebug)(struct hfc_multi *hc,
+ const char *function, int line);
+#else
+ void (*HFC_outb)(struct hfc_multi *hc, u_char reg,
+ u_char val);
+ void (*HFC_outb_nodebug)(struct hfc_multi *hc, u_char reg,
+ u_char val);
+ u_char (*HFC_inb)(struct hfc_multi *hc, u_char reg);
+ u_char (*HFC_inb_nodebug)(struct hfc_multi *hc, u_char reg);
+ u_short (*HFC_inw)(struct hfc_multi *hc, u_char reg);
+ u_short (*HFC_inw_nodebug)(struct hfc_multi *hc, u_char reg);
+ void (*HFC_wait)(struct hfc_multi *hc);
+ void (*HFC_wait_nodebug)(struct hfc_multi *hc);
+#endif
+ void (*read_fifo)(struct hfc_multi *hc, u_char *data,
+ int len);
+ void (*write_fifo)(struct hfc_multi *hc, u_char *data,
+ int len);
+ u_long pci_origmembase, plx_origmembase, dsp_origmembase;
+ u_char *pci_membase; /* PCI memory (MUST BE BYTE POINTER) */
+ u_char *plx_membase; /* PLX memory */
+ u_char *dsp_membase; /* DSP on PLX */
+ u_long pci_iobase; /* PCI IO */
+ struct hfcm_hw hw; /* remember data of write-only-registers */
+
+ u_long chip; /* chip configuration */
+ int masterclk; /* port that provides master clock -1=off */
+ int dtmf; /* flag that dtmf is currently in process */
+ int Flen; /* F-buffer size */
+ int Zlen; /* Z-buffer size (must be int for calculation)*/
+ int max_trans; /* maximum transparent fifo fill */
+ int Zmin; /* Z-buffer offset */
+ int DTMFbase; /* base address of DTMF coefficients */
+
+ u_int slots; /* number of PCM slots */
+ u_int leds; /* type of leds */
+ u_int ledcount; /* used to animate leds */
+ u_long ledstate; /* save last state of leds */
+ int opticalsupport; /* has the e1 board */
+ /* an optical Interface */
+ int dslot; /* channel # of d-channel (E1) default 16 */
+
+ u_long wdcount; /* every 500 ms we need to */
+ /* send the watchdog a signal */
+ u_char wdbyte; /* watchdog toggle byte */
+ u_int activity[8]; /* if there is any action on this */
+ /* port (will be cleared after */
+ /* showing led-states) */
+ int e1_state; /* keep track of last state */
+ int e1_getclock; /* if sync is retrieved from interface */
+ int syncronized; /* keep track of existing sync interface */
+ int e1_resync; /* resync jobs */
+
+ spinlock_t lock; /* the lock */
+
+ /*
+ * the channel index is counted from 0, regardless where the channel
+ * is located on the hfc-channel.
+ * the bch->channel is equvalent to the hfc-channel
+ */
+ struct hfc_chan chan[32];
+ u_char created[8]; /* what port is created */
+ signed char slot_owner[256]; /* owner channel of slot */
+};
+
+/* PLX GPIOs */
+#define PLX_GPIO4_DIR_BIT 13
+#define PLX_GPIO4_BIT 14
+#define PLX_GPIO5_DIR_BIT 16
+#define PLX_GPIO5_BIT 17
+#define PLX_GPIO6_DIR_BIT 19
+#define PLX_GPIO6_BIT 20
+#define PLX_GPIO7_DIR_BIT 22
+#define PLX_GPIO7_BIT 23
+#define PLX_GPIO8_DIR_BIT 25
+#define PLX_GPIO8_BIT 26
+
+#define PLX_GPIO4 (1 << PLX_GPIO4_BIT)
+#define PLX_GPIO5 (1 << PLX_GPIO5_BIT)
+#define PLX_GPIO6 (1 << PLX_GPIO6_BIT)
+#define PLX_GPIO7 (1 << PLX_GPIO7_BIT)
+#define PLX_GPIO8 (1 << PLX_GPIO8_BIT)
+
+#define PLX_GPIO4_DIR (1 << PLX_GPIO4_DIR_BIT)
+#define PLX_GPIO5_DIR (1 << PLX_GPIO5_DIR_BIT)
+#define PLX_GPIO6_DIR (1 << PLX_GPIO6_DIR_BIT)
+#define PLX_GPIO7_DIR (1 << PLX_GPIO7_DIR_BIT)
+#define PLX_GPIO8_DIR (1 << PLX_GPIO8_DIR_BIT)
+
+#define PLX_TERM_ON PLX_GPIO7
+#define PLX_SLAVE_EN_N PLX_GPIO5
+#define PLX_MASTER_EN PLX_GPIO6
+#define PLX_SYNC_O_EN PLX_GPIO4
+#define PLX_DSP_RES_N PLX_GPIO8
+/* GPIO4..8 Enable & Set to OUT, SLAVE_EN_N = 1 */
+#define PLX_GPIOC_INIT (PLX_GPIO4_DIR | PLX_GPIO5_DIR | PLX_GPIO6_DIR \
+ | PLX_GPIO7_DIR | PLX_GPIO8_DIR | PLX_SLAVE_EN_N)
+
+/* PLX Interrupt Control/STATUS */
+#define PLX_INTCSR_LINTI1_ENABLE 0x01
+#define PLX_INTCSR_LINTI1_STATUS 0x04
+#define PLX_INTCSR_LINTI2_ENABLE 0x08
+#define PLX_INTCSR_LINTI2_STATUS 0x20
+#define PLX_INTCSR_PCIINT_ENABLE 0x40
+
+/* PLX Registers */
+#define PLX_INTCSR 0x4c
+#define PLX_CNTRL 0x50
+#define PLX_GPIOC 0x54
+
+
+/*
+ * REGISTER SETTING FOR HFC-4S/8S AND HFC-E1
+ */
+
+/* write only registers */
+#define R_CIRM 0x00
+#define R_CTRL 0x01
+#define R_BRG_PCM_CFG 0x02
+#define R_RAM_ADDR0 0x08
+#define R_RAM_ADDR1 0x09
+#define R_RAM_ADDR2 0x0A
+#define R_FIRST_FIFO 0x0B
+#define R_RAM_SZ 0x0C
+#define R_FIFO_MD 0x0D
+#define R_INC_RES_FIFO 0x0E
+#define R_FSM_IDX 0x0F
+#define R_FIFO 0x0F
+#define R_SLOT 0x10
+#define R_IRQMSK_MISC 0x11
+#define R_SCI_MSK 0x12
+#define R_IRQ_CTRL 0x13
+#define R_PCM_MD0 0x14
+#define R_PCM_MD1 0x15
+#define R_PCM_MD2 0x15
+#define R_SH0H 0x15
+#define R_SH1H 0x15
+#define R_SH0L 0x15
+#define R_SH1L 0x15
+#define R_SL_SEL0 0x15
+#define R_SL_SEL1 0x15
+#define R_SL_SEL2 0x15
+#define R_SL_SEL3 0x15
+#define R_SL_SEL4 0x15
+#define R_SL_SEL5 0x15
+#define R_SL_SEL6 0x15
+#define R_SL_SEL7 0x15
+#define R_ST_SEL 0x16
+#define R_ST_SYNC 0x17
+#define R_CONF_EN 0x18
+#define R_TI_WD 0x1A
+#define R_BERT_WD_MD 0x1B
+#define R_DTMF 0x1C
+#define R_DTMF_N 0x1D
+#define R_E1_WR_STA 0x20
+#define R_E1_RD_STA 0x20
+#define R_LOS0 0x22
+#define R_LOS1 0x23
+#define R_RX0 0x24
+#define R_RX_FR0 0x25
+#define R_RX_FR1 0x26
+#define R_TX0 0x28
+#define R_TX1 0x29
+#define R_TX_FR0 0x2C
+
+#define R_TX_FR1 0x2D
+#define R_TX_FR2 0x2E
+#define R_JATT_ATT 0x2F /* undocumented */
+#define A_ST_RD_STATE 0x30
+#define A_ST_WR_STATE 0x30
+#define R_RX_OFF 0x30
+#define A_ST_CTRL0 0x31
+#define R_SYNC_OUT 0x31
+#define A_ST_CTRL1 0x32
+#define A_ST_CTRL2 0x33
+#define A_ST_SQ_WR 0x34
+#define R_TX_OFF 0x34
+#define R_SYNC_CTRL 0x35
+#define A_ST_CLK_DLY 0x37
+#define R_PWM0 0x38
+#define R_PWM1 0x39
+#define A_ST_B1_TX 0x3C
+#define A_ST_B2_TX 0x3D
+#define A_ST_D_TX 0x3E
+#define R_GPIO_OUT0 0x40
+#define R_GPIO_OUT1 0x41
+#define R_GPIO_EN0 0x42
+#define R_GPIO_EN1 0x43
+#define R_GPIO_SEL 0x44
+#define R_BRG_CTRL 0x45
+#define R_PWM_MD 0x46
+#define R_BRG_MD 0x47
+#define R_BRG_TIM0 0x48
+#define R_BRG_TIM1 0x49
+#define R_BRG_TIM2 0x4A
+#define R_BRG_TIM3 0x4B
+#define R_BRG_TIM_SEL01 0x4C
+#define R_BRG_TIM_SEL23 0x4D
+#define R_BRG_TIM_SEL45 0x4E
+#define R_BRG_TIM_SEL67 0x4F
+#define A_SL_CFG 0xD0
+#define A_CONF 0xD1
+#define A_CH_MSK 0xF4
+#define A_CON_HDLC 0xFA
+#define A_SUBCH_CFG 0xFB
+#define A_CHANNEL 0xFC
+#define A_FIFO_SEQ 0xFD
+#define A_IRQ_MSK 0xFF
+
+/* read only registers */
+#define A_Z12 0x04
+#define A_Z1L 0x04
+#define A_Z1 0x04
+#define A_Z1H 0x05
+#define A_Z2L 0x06
+#define A_Z2 0x06
+#define A_Z2H 0x07
+#define A_F1 0x0C
+#define A_F12 0x0C
+#define A_F2 0x0D
+#define R_IRQ_OVIEW 0x10
+#define R_IRQ_MISC 0x11
+#define R_IRQ_STATECH 0x12
+#define R_CONF_OFLOW 0x14
+#define R_RAM_USE 0x15
+#define R_CHIP_ID 0x16
+#define R_BERT_STA 0x17
+#define R_F0_CNTL 0x18
+#define R_F0_CNTH 0x19
+#define R_BERT_EC 0x1A
+#define R_BERT_ECL 0x1A
+#define R_BERT_ECH 0x1B
+#define R_STATUS 0x1C
+#define R_CHIP_RV 0x1F
+#define R_STATE 0x20
+#define R_SYNC_STA 0x24
+#define R_RX_SL0_0 0x25
+#define R_RX_SL0_1 0x26
+#define R_RX_SL0_2 0x27
+#define R_JATT_DIR 0x2b /* undocumented */
+#define R_SLIP 0x2c
+#define A_ST_RD_STA 0x30
+#define R_FAS_EC 0x30
+#define R_FAS_ECL 0x30
+#define R_FAS_ECH 0x31
+#define R_VIO_EC 0x32
+#define R_VIO_ECL 0x32
+#define R_VIO_ECH 0x33
+#define A_ST_SQ_RD 0x34
+#define R_CRC_EC 0x34
+#define R_CRC_ECL 0x34
+#define R_CRC_ECH 0x35
+#define R_E_EC 0x36
+#define R_E_ECL 0x36
+#define R_E_ECH 0x37
+#define R_SA6_SA13_EC 0x38
+#define R_SA6_SA13_ECL 0x38
+#define R_SA6_SA13_ECH 0x39
+#define R_SA6_SA23_EC 0x3A
+#define R_SA6_SA23_ECL 0x3A
+#define R_SA6_SA23_ECH 0x3B
+#define A_ST_B1_RX 0x3C
+#define A_ST_B2_RX 0x3D
+#define A_ST_D_RX 0x3E
+#define A_ST_E_RX 0x3F
+#define R_GPIO_IN0 0x40
+#define R_GPIO_IN1 0x41
+#define R_GPI_IN0 0x44
+#define R_GPI_IN1 0x45
+#define R_GPI_IN2 0x46
+#define R_GPI_IN3 0x47
+#define R_INT_DATA 0x88
+#define R_IRQ_FIFO_BL0 0xC8
+#define R_IRQ_FIFO_BL1 0xC9
+#define R_IRQ_FIFO_BL2 0xCA
+#define R_IRQ_FIFO_BL3 0xCB
+#define R_IRQ_FIFO_BL4 0xCC
+#define R_IRQ_FIFO_BL5 0xCD
+#define R_IRQ_FIFO_BL6 0xCE
+#define R_IRQ_FIFO_BL7 0xCF
+
+/* read and write registers */
+#define A_FIFO_DATA0 0x80
+#define A_FIFO_DATA1 0x80
+#define A_FIFO_DATA2 0x80
+#define A_FIFO_DATA0_NOINC 0x84
+#define A_FIFO_DATA1_NOINC 0x84
+#define A_FIFO_DATA2_NOINC 0x84
+#define R_RAM_DATA 0xC0
+
+
+/*
+ * BIT SETTING FOR HFC-4S/8S AND HFC-E1
+ */
+
+/* chapter 2: universal bus interface */
+/* R_CIRM */
+#define V_IRQ_SEL 0x01
+#define V_SRES 0x08
+#define V_HFCRES 0x10
+#define V_PCMRES 0x20
+#define V_STRES 0x40
+#define V_ETRES 0x40
+#define V_RLD_EPR 0x80
+/* R_CTRL */
+#define V_FIFO_LPRIO 0x02
+#define V_SLOW_RD 0x04
+#define V_EXT_RAM 0x08
+#define V_CLK_OFF 0x20
+#define V_ST_CLK 0x40
+/* R_RAM_ADDR0 */
+#define V_RAM_ADDR2 0x01
+#define V_ADDR_RES 0x40
+#define V_ADDR_INC 0x80
+/* R_RAM_SZ */
+#define V_RAM_SZ 0x01
+#define V_PWM0_16KHZ 0x10
+#define V_PWM1_16KHZ 0x20
+#define V_FZ_MD 0x80
+/* R_CHIP_ID */
+#define V_PNP_IRQ 0x01
+#define V_CHIP_ID 0x10
+
+/* chapter 3: data flow */
+/* R_FIRST_FIFO */
+#define V_FIRST_FIRO_DIR 0x01
+#define V_FIRST_FIFO_NUM 0x02
+/* R_FIFO_MD */
+#define V_FIFO_MD 0x01
+#define V_CSM_MD 0x04
+#define V_FSM_MD 0x08
+#define V_FIFO_SZ 0x10
+/* R_FIFO */
+#define V_FIFO_DIR 0x01
+#define V_FIFO_NUM 0x02
+#define V_REV 0x80
+/* R_SLOT */
+#define V_SL_DIR 0x01
+#define V_SL_NUM 0x02
+/* A_SL_CFG */
+#define V_CH_DIR 0x01
+#define V_CH_SEL 0x02
+#define V_ROUTING 0x40
+/* A_CON_HDLC */
+#define V_IFF 0x01
+#define V_HDLC_TRP 0x02
+#define V_TRP_IRQ 0x04
+#define V_DATA_FLOW 0x20
+/* A_SUBCH_CFG */
+#define V_BIT_CNT 0x01
+#define V_START_BIT 0x08
+#define V_LOOP_FIFO 0x40
+#define V_INV_DATA 0x80
+/* A_CHANNEL */
+#define V_CH_DIR0 0x01
+#define V_CH_NUM0 0x02
+/* A_FIFO_SEQ */
+#define V_NEXT_FIFO_DIR 0x01
+#define V_NEXT_FIFO_NUM 0x02
+#define V_SEQ_END 0x40
+
+/* chapter 4: FIFO handling and HDLC controller */
+/* R_INC_RES_FIFO */
+#define V_INC_F 0x01
+#define V_RES_F 0x02
+#define V_RES_LOST 0x04
+
+/* chapter 5: S/T interface */
+/* R_SCI_MSK */
+#define V_SCI_MSK_ST0 0x01
+#define V_SCI_MSK_ST1 0x02
+#define V_SCI_MSK_ST2 0x04
+#define V_SCI_MSK_ST3 0x08
+#define V_SCI_MSK_ST4 0x10
+#define V_SCI_MSK_ST5 0x20
+#define V_SCI_MSK_ST6 0x40
+#define V_SCI_MSK_ST7 0x80
+/* R_ST_SEL */
+#define V_ST_SEL 0x01
+#define V_MULT_ST 0x08
+/* R_ST_SYNC */
+#define V_SYNC_SEL 0x01
+#define V_AUTO_SYNC 0x08
+/* A_ST_WR_STA */
+#define V_ST_SET_STA 0x01
+#define V_ST_LD_STA 0x10
+#define V_ST_ACT 0x20
+#define V_SET_G2_G3 0x80
+/* A_ST_CTRL0 */
+#define V_B1_EN 0x01
+#define V_B2_EN 0x02
+#define V_ST_MD 0x04
+#define V_D_PRIO 0x08
+#define V_SQ_EN 0x10
+#define V_96KHZ 0x20
+#define V_TX_LI 0x40
+#define V_ST_STOP 0x80
+/* A_ST_CTRL1 */
+#define V_G2_G3_EN 0x01
+#define V_D_HI 0x04
+#define V_E_IGNO 0x08
+#define V_E_LO 0x10
+#define V_B12_SWAP 0x80
+/* A_ST_CTRL2 */
+#define V_B1_RX_EN 0x01
+#define V_B2_RX_EN 0x02
+#define V_ST_TRIS 0x40
+/* A_ST_CLK_DLY */
+#define V_ST_CK_DLY 0x01
+#define V_ST_SMPL 0x10
+/* A_ST_D_TX */
+#define V_ST_D_TX 0x40
+/* R_IRQ_STATECH */
+#define V_SCI_ST0 0x01
+#define V_SCI_ST1 0x02
+#define V_SCI_ST2 0x04
+#define V_SCI_ST3 0x08
+#define V_SCI_ST4 0x10
+#define V_SCI_ST5 0x20
+#define V_SCI_ST6 0x40
+#define V_SCI_ST7 0x80
+/* A_ST_RD_STA */
+#define V_ST_STA 0x01
+#define V_FR_SYNC_ST 0x10
+#define V_TI2_EXP 0x20
+#define V_INFO0 0x40
+#define V_G2_G3 0x80
+/* A_ST_SQ_RD */
+#define V_ST_SQ 0x01
+#define V_MF_RX_RDY 0x10
+#define V_MF_TX_RDY 0x80
+/* A_ST_D_RX */
+#define V_ST_D_RX 0x40
+/* A_ST_E_RX */
+#define V_ST_E_RX 0x40
+
+/* chapter 5: E1 interface */
+/* R_E1_WR_STA */
+/* R_E1_RD_STA */
+#define V_E1_SET_STA 0x01
+#define V_E1_LD_STA 0x10
+/* R_RX0 */
+#define V_RX_CODE 0x01
+#define V_RX_FBAUD 0x04
+#define V_RX_CMI 0x08
+#define V_RX_INV_CMI 0x10
+#define V_RX_INV_CLK 0x20
+#define V_RX_INV_DATA 0x40
+#define V_AIS_ITU 0x80
+/* R_RX_FR0 */
+#define V_NO_INSYNC 0x01
+#define V_AUTO_RESYNC 0x02
+#define V_AUTO_RECO 0x04
+#define V_SWORD_COND 0x08
+#define V_SYNC_LOSS 0x10
+#define V_XCRC_SYNC 0x20
+#define V_MF_RESYNC 0x40
+#define V_RESYNC 0x80
+/* R_RX_FR1 */
+#define V_RX_MF 0x01
+#define V_RX_MF_SYNC 0x02
+#define V_RX_SL0_RAM 0x04
+#define V_ERR_SIM 0x20
+#define V_RES_NMF 0x40
+/* R_TX0 */
+#define V_TX_CODE 0x01
+#define V_TX_FBAUD 0x04
+#define V_TX_CMI_CODE 0x08
+#define V_TX_INV_CMI_CODE 0x10
+#define V_TX_INV_CLK 0x20
+#define V_TX_INV_DATA 0x40
+#define V_OUT_EN 0x80
+/* R_TX1 */
+#define V_INV_CLK 0x01
+#define V_EXCHG_DATA_LI 0x02
+#define V_AIS_OUT 0x04
+#define V_ATX 0x20
+#define V_NTRI 0x40
+#define V_AUTO_ERR_RES 0x80
+/* R_TX_FR0 */
+#define V_TRP_FAS 0x01
+#define V_TRP_NFAS 0x02
+#define V_TRP_RAL 0x04
+#define V_TRP_SA 0x08
+/* R_TX_FR1 */
+#define V_TX_FAS 0x01
+#define V_TX_NFAS 0x02
+#define V_TX_RAL 0x04
+#define V_TX_SA 0x08
+/* R_TX_FR2 */
+#define V_TX_MF 0x01
+#define V_TRP_SL0 0x02
+#define V_TX_SL0_RAM 0x04
+#define V_TX_E 0x10
+#define V_NEG_E 0x20
+#define V_XS12_ON 0x40
+#define V_XS15_ON 0x80
+/* R_RX_OFF */
+#define V_RX_SZ 0x01
+#define V_RX_INIT 0x04
+/* R_SYNC_OUT */
+#define V_SYNC_E1_RX 0x01
+#define V_IPATS0 0x20
+#define V_IPATS1 0x40
+#define V_IPATS2 0x80
+/* R_TX_OFF */
+#define V_TX_SZ 0x01
+#define V_TX_INIT 0x04
+/* R_SYNC_CTRL */
+#define V_EXT_CLK_SYNC 0x01
+#define V_SYNC_OFFS 0x02
+#define V_PCM_SYNC 0x04
+#define V_NEG_CLK 0x08
+#define V_HCLK 0x10
+/*
+#define V_JATT_AUTO_DEL 0x20
+#define V_JATT_AUTO 0x40
+*/
+#define V_JATT_OFF 0x80
+/* R_STATE */
+#define V_E1_STA 0x01
+#define V_ALT_FR_RX 0x40
+#define V_ALT_FR_TX 0x80
+/* R_SYNC_STA */
+#define V_RX_STA 0x01
+#define V_FR_SYNC_E1 0x04
+#define V_SIG_LOS 0x08
+#define V_MFA_STA 0x10
+#define V_AIS 0x40
+#define V_NO_MF_SYNC 0x80
+/* R_RX_SL0_0 */
+#define V_SI_FAS 0x01
+#define V_SI_NFAS 0x02
+#define V_A 0x04
+#define V_CRC_OK 0x08
+#define V_TX_E1 0x10
+#define V_TX_E2 0x20
+#define V_RX_E1 0x40
+#define V_RX_E2 0x80
+/* R_SLIP */
+#define V_SLIP_RX 0x01
+#define V_FOSLIP_RX 0x08
+#define V_SLIP_TX 0x10
+#define V_FOSLIP_TX 0x80
+
+/* chapter 6: PCM interface */
+/* R_PCM_MD0 */
+#define V_PCM_MD 0x01
+#define V_C4_POL 0x02
+#define V_F0_NEG 0x04
+#define V_F0_LEN 0x08
+#define V_PCM_ADDR 0x10
+/* R_SL_SEL0 */
+#define V_SL_SEL0 0x01
+#define V_SH_SEL0 0x80
+/* R_SL_SEL1 */
+#define V_SL_SEL1 0x01
+#define V_SH_SEL1 0x80
+/* R_SL_SEL2 */
+#define V_SL_SEL2 0x01
+#define V_SH_SEL2 0x80
+/* R_SL_SEL3 */
+#define V_SL_SEL3 0x01
+#define V_SH_SEL3 0x80
+/* R_SL_SEL4 */
+#define V_SL_SEL4 0x01
+#define V_SH_SEL4 0x80
+/* R_SL_SEL5 */
+#define V_SL_SEL5 0x01
+#define V_SH_SEL5 0x80
+/* R_SL_SEL6 */
+#define V_SL_SEL6 0x01
+#define V_SH_SEL6 0x80
+/* R_SL_SEL7 */
+#define V_SL_SEL7 0x01
+#define V_SH_SEL7 0x80
+/* R_PCM_MD1 */
+#define V_ODEC_CON 0x01
+#define V_PLL_ADJ 0x04
+#define V_PCM_DR 0x10
+#define V_PCM_LOOP 0x40
+/* R_PCM_MD2 */
+#define V_SYNC_PLL 0x02
+#define V_SYNC_SRC 0x04
+#define V_SYNC_OUT 0x08
+#define V_ICR_FR_TIME 0x40
+#define V_EN_PLL 0x80
+
+/* chapter 7: pulse width modulation */
+/* R_PWM_MD */
+#define V_EXT_IRQ_EN 0x08
+#define V_PWM0_MD 0x10
+#define V_PWM1_MD 0x40
+
+/* chapter 8: multiparty audio conferences */
+/* R_CONF_EN */
+#define V_CONF_EN 0x01
+#define V_ULAW 0x80
+/* A_CONF */
+#define V_CONF_NUM 0x01
+#define V_NOISE_SUPPR 0x08
+#define V_ATT_LEV 0x20
+#define V_CONF_SL 0x80
+/* R_CONF_OFLOW */
+#define V_CONF_OFLOW0 0x01
+#define V_CONF_OFLOW1 0x02
+#define V_CONF_OFLOW2 0x04
+#define V_CONF_OFLOW3 0x08
+#define V_CONF_OFLOW4 0x10
+#define V_CONF_OFLOW5 0x20
+#define V_CONF_OFLOW6 0x40
+#define V_CONF_OFLOW7 0x80
+
+/* chapter 9: DTMF contoller */
+/* R_DTMF0 */
+#define V_DTMF_EN 0x01
+#define V_HARM_SEL 0x02
+#define V_DTMF_RX_CH 0x04
+#define V_DTMF_STOP 0x08
+#define V_CHBL_SEL 0x10
+#define V_RST_DTMF 0x40
+#define V_ULAW_SEL 0x80
+
+/* chapter 10: BERT */
+/* R_BERT_WD_MD */
+#define V_PAT_SEQ 0x01
+#define V_BERT_ERR 0x08
+#define V_AUTO_WD_RES 0x20
+#define V_WD_RES 0x80
+/* R_BERT_STA */
+#define V_BERT_SYNC_SRC 0x01
+#define V_BERT_SYNC 0x10
+#define V_BERT_INV_DATA 0x20
+
+/* chapter 11: auxiliary interface */
+/* R_BRG_PCM_CFG */
+#define V_BRG_EN 0x01
+#define V_BRG_MD 0x02
+#define V_PCM_CLK 0x20
+#define V_ADDR_WRDLY 0x40
+/* R_BRG_CTRL */
+#define V_BRG_CS 0x01
+#define V_BRG_ADDR 0x08
+#define V_BRG_CS_SRC 0x80
+/* R_BRG_MD */
+#define V_BRG_MD0 0x01
+#define V_BRG_MD1 0x02
+#define V_BRG_MD2 0x04
+#define V_BRG_MD3 0x08
+#define V_BRG_MD4 0x10
+#define V_BRG_MD5 0x20
+#define V_BRG_MD6 0x40
+#define V_BRG_MD7 0x80
+/* R_BRG_TIM0 */
+#define V_BRG_TIM0_IDLE 0x01
+#define V_BRG_TIM0_CLK 0x10
+/* R_BRG_TIM1 */
+#define V_BRG_TIM1_IDLE 0x01
+#define V_BRG_TIM1_CLK 0x10
+/* R_BRG_TIM2 */
+#define V_BRG_TIM2_IDLE 0x01
+#define V_BRG_TIM2_CLK 0x10
+/* R_BRG_TIM3 */
+#define V_BRG_TIM3_IDLE 0x01
+#define V_BRG_TIM3_CLK 0x10
+/* R_BRG_TIM_SEL01 */
+#define V_BRG_WR_SEL0 0x01
+#define V_BRG_RD_SEL0 0x04
+#define V_BRG_WR_SEL1 0x10
+#define V_BRG_RD_SEL1 0x40
+/* R_BRG_TIM_SEL23 */
+#define V_BRG_WR_SEL2 0x01
+#define V_BRG_RD_SEL2 0x04
+#define V_BRG_WR_SEL3 0x10
+#define V_BRG_RD_SEL3 0x40
+/* R_BRG_TIM_SEL45 */
+#define V_BRG_WR_SEL4 0x01
+#define V_BRG_RD_SEL4 0x04
+#define V_BRG_WR_SEL5 0x10
+#define V_BRG_RD_SEL5 0x40
+/* R_BRG_TIM_SEL67 */
+#define V_BRG_WR_SEL6 0x01
+#define V_BRG_RD_SEL6 0x04
+#define V_BRG_WR_SEL7 0x10
+#define V_BRG_RD_SEL7 0x40
+
+/* chapter 12: clock, reset, interrupt, timer and watchdog */
+/* R_IRQMSK_MISC */
+#define V_STA_IRQMSK 0x01
+#define V_TI_IRQMSK 0x02
+#define V_PROC_IRQMSK 0x04
+#define V_DTMF_IRQMSK 0x08
+#define V_IRQ1S_MSK 0x10
+#define V_SA6_IRQMSK 0x20
+#define V_RX_EOMF_MSK 0x40
+#define V_TX_EOMF_MSK 0x80
+/* R_IRQ_CTRL */
+#define V_FIFO_IRQ 0x01
+#define V_GLOB_IRQ_EN 0x08
+#define V_IRQ_POL 0x10
+/* R_TI_WD */
+#define V_EV_TS 0x01
+#define V_WD_TS 0x10
+/* A_IRQ_MSK */
+#define V_IRQ 0x01
+#define V_BERT_EN 0x02
+#define V_MIX_IRQ 0x04
+/* R_IRQ_OVIEW */
+#define V_IRQ_FIFO_BL0 0x01
+#define V_IRQ_FIFO_BL1 0x02
+#define V_IRQ_FIFO_BL2 0x04
+#define V_IRQ_FIFO_BL3 0x08
+#define V_IRQ_FIFO_BL4 0x10
+#define V_IRQ_FIFO_BL5 0x20
+#define V_IRQ_FIFO_BL6 0x40
+#define V_IRQ_FIFO_BL7 0x80
+/* R_IRQ_MISC */
+#define V_STA_IRQ 0x01
+#define V_TI_IRQ 0x02
+#define V_IRQ_PROC 0x04
+#define V_DTMF_IRQ 0x08
+#define V_IRQ1S 0x10
+#define V_SA6_IRQ 0x20
+#define V_RX_EOMF 0x40
+#define V_TX_EOMF 0x80
+/* R_STATUS */
+#define V_BUSY 0x01
+#define V_PROC 0x02
+#define V_DTMF_STA 0x04
+#define V_LOST_STA 0x08
+#define V_SYNC_IN 0x10
+#define V_EXT_IRQSTA 0x20
+#define V_MISC_IRQSTA 0x40
+#define V_FR_IRQSTA 0x80
+/* R_IRQ_FIFO_BL0 */
+#define V_IRQ_FIFO0_TX 0x01
+#define V_IRQ_FIFO0_RX 0x02
+#define V_IRQ_FIFO1_TX 0x04
+#define V_IRQ_FIFO1_RX 0x08
+#define V_IRQ_FIFO2_TX 0x10
+#define V_IRQ_FIFO2_RX 0x20
+#define V_IRQ_FIFO3_TX 0x40
+#define V_IRQ_FIFO3_RX 0x80
+/* R_IRQ_FIFO_BL1 */
+#define V_IRQ_FIFO4_TX 0x01
+#define V_IRQ_FIFO4_RX 0x02
+#define V_IRQ_FIFO5_TX 0x04
+#define V_IRQ_FIFO5_RX 0x08
+#define V_IRQ_FIFO6_TX 0x10
+#define V_IRQ_FIFO6_RX 0x20
+#define V_IRQ_FIFO7_TX 0x40
+#define V_IRQ_FIFO7_RX 0x80
+/* R_IRQ_FIFO_BL2 */
+#define V_IRQ_FIFO8_TX 0x01
+#define V_IRQ_FIFO8_RX 0x02
+#define V_IRQ_FIFO9_TX 0x04
+#define V_IRQ_FIFO9_RX 0x08
+#define V_IRQ_FIFO10_TX 0x10
+#define V_IRQ_FIFO10_RX 0x20
+#define V_IRQ_FIFO11_TX 0x40
+#define V_IRQ_FIFO11_RX 0x80
+/* R_IRQ_FIFO_BL3 */
+#define V_IRQ_FIFO12_TX 0x01
+#define V_IRQ_FIFO12_RX 0x02
+#define V_IRQ_FIFO13_TX 0x04
+#define V_IRQ_FIFO13_RX 0x08
+#define V_IRQ_FIFO14_TX 0x10
+#define V_IRQ_FIFO14_RX 0x20
+#define V_IRQ_FIFO15_TX 0x40
+#define V_IRQ_FIFO15_RX 0x80
+/* R_IRQ_FIFO_BL4 */
+#define V_IRQ_FIFO16_TX 0x01
+#define V_IRQ_FIFO16_RX 0x02
+#define V_IRQ_FIFO17_TX 0x04
+#define V_IRQ_FIFO17_RX 0x08
+#define V_IRQ_FIFO18_TX 0x10
+#define V_IRQ_FIFO18_RX 0x20
+#define V_IRQ_FIFO19_TX 0x40
+#define V_IRQ_FIFO19_RX 0x80
+/* R_IRQ_FIFO_BL5 */
+#define V_IRQ_FIFO20_TX 0x01
+#define V_IRQ_FIFO20_RX 0x02
+#define V_IRQ_FIFO21_TX 0x04
+#define V_IRQ_FIFO21_RX 0x08
+#define V_IRQ_FIFO22_TX 0x10
+#define V_IRQ_FIFO22_RX 0x20
+#define V_IRQ_FIFO23_TX 0x40
+#define V_IRQ_FIFO23_RX 0x80
+/* R_IRQ_FIFO_BL6 */
+#define V_IRQ_FIFO24_TX 0x01
+#define V_IRQ_FIFO24_RX 0x02
+#define V_IRQ_FIFO25_TX 0x04
+#define V_IRQ_FIFO25_RX 0x08
+#define V_IRQ_FIFO26_TX 0x10
+#define V_IRQ_FIFO26_RX 0x20
+#define V_IRQ_FIFO27_TX 0x40
+#define V_IRQ_FIFO27_RX 0x80
+/* R_IRQ_FIFO_BL7 */
+#define V_IRQ_FIFO28_TX 0x01
+#define V_IRQ_FIFO28_RX 0x02
+#define V_IRQ_FIFO29_TX 0x04
+#define V_IRQ_FIFO29_RX 0x08
+#define V_IRQ_FIFO30_TX 0x10
+#define V_IRQ_FIFO30_RX 0x20
+#define V_IRQ_FIFO31_TX 0x40
+#define V_IRQ_FIFO31_RX 0x80
+
+/* chapter 13: general purpose I/O pins (GPIO) and input pins (GPI) */
+/* R_GPIO_OUT0 */
+#define V_GPIO_OUT0 0x01
+#define V_GPIO_OUT1 0x02
+#define V_GPIO_OUT2 0x04
+#define V_GPIO_OUT3 0x08
+#define V_GPIO_OUT4 0x10
+#define V_GPIO_OUT5 0x20
+#define V_GPIO_OUT6 0x40
+#define V_GPIO_OUT7 0x80
+/* R_GPIO_OUT1 */
+#define V_GPIO_OUT8 0x01
+#define V_GPIO_OUT9 0x02
+#define V_GPIO_OUT10 0x04
+#define V_GPIO_OUT11 0x08
+#define V_GPIO_OUT12 0x10
+#define V_GPIO_OUT13 0x20
+#define V_GPIO_OUT14 0x40
+#define V_GPIO_OUT15 0x80
+/* R_GPIO_EN0 */
+#define V_GPIO_EN0 0x01
+#define V_GPIO_EN1 0x02
+#define V_GPIO_EN2 0x04
+#define V_GPIO_EN3 0x08
+#define V_GPIO_EN4 0x10
+#define V_GPIO_EN5 0x20
+#define V_GPIO_EN6 0x40
+#define V_GPIO_EN7 0x80
+/* R_GPIO_EN1 */
+#define V_GPIO_EN8 0x01
+#define V_GPIO_EN9 0x02
+#define V_GPIO_EN10 0x04
+#define V_GPIO_EN11 0x08
+#define V_GPIO_EN12 0x10
+#define V_GPIO_EN13 0x20
+#define V_GPIO_EN14 0x40
+#define V_GPIO_EN15 0x80
+/* R_GPIO_SEL */
+#define V_GPIO_SEL0 0x01
+#define V_GPIO_SEL1 0x02
+#define V_GPIO_SEL2 0x04
+#define V_GPIO_SEL3 0x08
+#define V_GPIO_SEL4 0x10
+#define V_GPIO_SEL5 0x20
+#define V_GPIO_SEL6 0x40
+#define V_GPIO_SEL7 0x80
+/* R_GPIO_IN0 */
+#define V_GPIO_IN0 0x01
+#define V_GPIO_IN1 0x02
+#define V_GPIO_IN2 0x04
+#define V_GPIO_IN3 0x08
+#define V_GPIO_IN4 0x10
+#define V_GPIO_IN5 0x20
+#define V_GPIO_IN6 0x40
+#define V_GPIO_IN7 0x80
+/* R_GPIO_IN1 */
+#define V_GPIO_IN8 0x01
+#define V_GPIO_IN9 0x02
+#define V_GPIO_IN10 0x04
+#define V_GPIO_IN11 0x08
+#define V_GPIO_IN12 0x10
+#define V_GPIO_IN13 0x20
+#define V_GPIO_IN14 0x40
+#define V_GPIO_IN15 0x80
+/* R_GPI_IN0 */
+#define V_GPI_IN0 0x01
+#define V_GPI_IN1 0x02
+#define V_GPI_IN2 0x04
+#define V_GPI_IN3 0x08
+#define V_GPI_IN4 0x10
+#define V_GPI_IN5 0x20
+#define V_GPI_IN6 0x40
+#define V_GPI_IN7 0x80
+/* R_GPI_IN1 */
+#define V_GPI_IN8 0x01
+#define V_GPI_IN9 0x02
+#define V_GPI_IN10 0x04
+#define V_GPI_IN11 0x08
+#define V_GPI_IN12 0x10
+#define V_GPI_IN13 0x20
+#define V_GPI_IN14 0x40
+#define V_GPI_IN15 0x80
+/* R_GPI_IN2 */
+#define V_GPI_IN16 0x01
+#define V_GPI_IN17 0x02
+#define V_GPI_IN18 0x04
+#define V_GPI_IN19 0x08
+#define V_GPI_IN20 0x10
+#define V_GPI_IN21 0x20
+#define V_GPI_IN22 0x40
+#define V_GPI_IN23 0x80
+/* R_GPI_IN3 */
+#define V_GPI_IN24 0x01
+#define V_GPI_IN25 0x02
+#define V_GPI_IN26 0x04
+#define V_GPI_IN27 0x08
+#define V_GPI_IN28 0x10
+#define V_GPI_IN29 0x20
+#define V_GPI_IN30 0x40
+#define V_GPI_IN31 0x80
+
+/* map of all registers, used for debugging */
+
+#ifdef HFC_REGISTER_DEBUG
+struct hfc_register_names {
+ char *name;
+ u_char reg;
+} hfc_register_names[] = {
+ /* write registers */
+ {"R_CIRM", 0x00},
+ {"R_CTRL", 0x01},
+ {"R_BRG_PCM_CFG ", 0x02},
+ {"R_RAM_ADDR0", 0x08},
+ {"R_RAM_ADDR1", 0x09},
+ {"R_RAM_ADDR2", 0x0A},
+ {"R_FIRST_FIFO", 0x0B},
+ {"R_RAM_SZ", 0x0C},
+ {"R_FIFO_MD", 0x0D},
+ {"R_INC_RES_FIFO", 0x0E},
+ {"R_FIFO / R_FSM_IDX", 0x0F},
+ {"R_SLOT", 0x10},
+ {"R_IRQMSK_MISC", 0x11},
+ {"R_SCI_MSK", 0x12},
+ {"R_IRQ_CTRL", 0x13},
+ {"R_PCM_MD0", 0x14},
+ {"R_0x15", 0x15},
+ {"R_ST_SEL", 0x16},
+ {"R_ST_SYNC", 0x17},
+ {"R_CONF_EN", 0x18},
+ {"R_TI_WD", 0x1A},
+ {"R_BERT_WD_MD", 0x1B},
+ {"R_DTMF", 0x1C},
+ {"R_DTMF_N", 0x1D},
+ {"R_E1_XX_STA", 0x20},
+ {"R_LOS0", 0x22},
+ {"R_LOS1", 0x23},
+ {"R_RX0", 0x24},
+ {"R_RX_FR0", 0x25},
+ {"R_RX_FR1", 0x26},
+ {"R_TX0", 0x28},
+ {"R_TX1", 0x29},
+ {"R_TX_FR0", 0x2C},
+ {"R_TX_FR1", 0x2D},
+ {"R_TX_FR2", 0x2E},
+ {"R_JATT_ATT", 0x2F},
+ {"A_ST_xx_STA/R_RX_OFF", 0x30},
+ {"A_ST_CTRL0/R_SYNC_OUT", 0x31},
+ {"A_ST_CTRL1", 0x32},
+ {"A_ST_CTRL2", 0x33},
+ {"A_ST_SQ_WR", 0x34},
+ {"R_TX_OFF", 0x34},
+ {"R_SYNC_CTRL", 0x35},
+ {"A_ST_CLK_DLY", 0x37},
+ {"R_PWM0", 0x38},
+ {"R_PWM1", 0x39},
+ {"A_ST_B1_TX", 0x3C},
+ {"A_ST_B2_TX", 0x3D},
+ {"A_ST_D_TX", 0x3E},
+ {"R_GPIO_OUT0", 0x40},
+ {"R_GPIO_OUT1", 0x41},
+ {"R_GPIO_EN0", 0x42},
+ {"R_GPIO_EN1", 0x43},
+ {"R_GPIO_SEL", 0x44},
+ {"R_BRG_CTRL", 0x45},
+ {"R_PWM_MD", 0x46},
+ {"R_BRG_MD", 0x47},
+ {"R_BRG_TIM0", 0x48},
+ {"R_BRG_TIM1", 0x49},
+ {"R_BRG_TIM2", 0x4A},
+ {"R_BRG_TIM3", 0x4B},
+ {"R_BRG_TIM_SEL01", 0x4C},
+ {"R_BRG_TIM_SEL23", 0x4D},
+ {"R_BRG_TIM_SEL45", 0x4E},
+ {"R_BRG_TIM_SEL67", 0x4F},
+ {"A_FIFO_DATA0-2", 0x80},
+ {"A_FIFO_DATA0-2_NOINC", 0x84},
+ {"R_RAM_DATA", 0xC0},
+ {"A_SL_CFG", 0xD0},
+ {"A_CONF", 0xD1},
+ {"A_CH_MSK", 0xF4},
+ {"A_CON_HDLC", 0xFA},
+ {"A_SUBCH_CFG", 0xFB},
+ {"A_CHANNEL", 0xFC},
+ {"A_FIFO_SEQ", 0xFD},
+ {"A_IRQ_MSK", 0xFF},
+ {NULL, 0},
+
+ /* read registers */
+ {"A_Z1", 0x04},
+ {"A_Z1H", 0x05},
+ {"A_Z2", 0x06},
+ {"A_Z2H", 0x07},
+ {"A_F1", 0x0C},
+ {"A_F2", 0x0D},
+ {"R_IRQ_OVIEW", 0x10},
+ {"R_IRQ_MISC", 0x11},
+ {"R_IRQ_STATECH", 0x12},
+ {"R_CONF_OFLOW", 0x14},
+ {"R_RAM_USE", 0x15},
+ {"R_CHIP_ID", 0x16},
+ {"R_BERT_STA", 0x17},
+ {"R_F0_CNTL", 0x18},
+ {"R_F0_CNTH", 0x19},
+ {"R_BERT_ECL", 0x1A},
+ {"R_BERT_ECH", 0x1B},
+ {"R_STATUS", 0x1C},
+ {"R_CHIP_RV", 0x1F},
+ {"R_STATE", 0x20},
+ {"R_SYNC_STA", 0x24},
+ {"R_RX_SL0_0", 0x25},
+ {"R_RX_SL0_1", 0x26},
+ {"R_RX_SL0_2", 0x27},
+ {"R_JATT_DIR", 0x2b},
+ {"R_SLIP", 0x2c},
+ {"A_ST_RD_STA", 0x30},
+ {"R_FAS_ECL", 0x30},
+ {"R_FAS_ECH", 0x31},
+ {"R_VIO_ECL", 0x32},
+ {"R_VIO_ECH", 0x33},
+ {"R_CRC_ECL / A_ST_SQ_RD", 0x34},
+ {"R_CRC_ECH", 0x35},
+ {"R_E_ECL", 0x36},
+ {"R_E_ECH", 0x37},
+ {"R_SA6_SA13_ECL", 0x38},
+ {"R_SA6_SA13_ECH", 0x39},
+ {"R_SA6_SA23_ECL", 0x3A},
+ {"R_SA6_SA23_ECH", 0x3B},
+ {"A_ST_B1_RX", 0x3C},
+ {"A_ST_B2_RX", 0x3D},
+ {"A_ST_D_RX", 0x3E},
+ {"A_ST_E_RX", 0x3F},
+ {"R_GPIO_IN0", 0x40},
+ {"R_GPIO_IN1", 0x41},
+ {"R_GPI_IN0", 0x44},
+ {"R_GPI_IN1", 0x45},
+ {"R_GPI_IN2", 0x46},
+ {"R_GPI_IN3", 0x47},
+ {"A_FIFO_DATA0-2", 0x80},
+ {"A_FIFO_DATA0-2_NOINC", 0x84},
+ {"R_INT_DATA", 0x88},
+ {"R_RAM_DATA", 0xC0},
+ {"R_IRQ_FIFO_BL0", 0xC8},
+ {"R_IRQ_FIFO_BL1", 0xC9},
+ {"R_IRQ_FIFO_BL2", 0xCA},
+ {"R_IRQ_FIFO_BL3", 0xCB},
+ {"R_IRQ_FIFO_BL4", 0xCC},
+ {"R_IRQ_FIFO_BL5", 0xCD},
+ {"R_IRQ_FIFO_BL6", 0xCE},
+ {"R_IRQ_FIFO_BL7", 0xCF},
+};
+#endif /* HFC_REGISTER_DEBUG */
+
diff --git a/drivers/isdn/hardware/mISDN/hfcmulti.c b/drivers/isdn/hardware/mISDN/hfcmulti.c
new file mode 100644
index 0000000..2649ea5
--- /dev/null
+++ b/drivers/isdn/hardware/mISDN/hfcmulti.c
@@ -0,0 +1,5320 @@
+/*
+ * hfcmulti.c low level driver for hfc-4s/hfc-8s/hfc-e1 based cards
+ *
+ * Author Andreas Eversberg (jolly@...rsberg.eu)
+ * ported to mqueue mechanism:
+ * Peter Sprenger (sprengermoving-bytes.de)
+ *
+ * inspired by existing hfc-pci driver:
+ * Copyright 1999 by Werner Cornelius (werner@...n-development.de)
+ * Copyright 2008 by Karsten Keil (kkeil@...e.de)
+ * Copyright 2008 by Andreas Eversberg (jolly@...rsberg.eu)
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *
+ * Thanks to Cologne Chip AG for this great controller!
+ */
+
+/*
+ * module parameters:
+ * type:
+ * By default (0), the card is automatically detected.
+ * Or use the following combinations:
+ * Bit 0-7 = 0x00001 = HFC-E1 (1 port)
+ * or Bit 0-7 = 0x00004 = HFC-4S (4 ports)
+ * or Bit 0-7 = 0x00008 = HFC-8S (8 ports)
+ * Bit 8 = 0x00100 = uLaw (instead of aLaw)
+ * Bit 9 = 0x00200 = Disable DTMF detect on all B-channels via hardware
+ * Bit 10 = spare
+ * Bit 11 = 0x00800 = Force PCM bus into slave mode. (otherwhise auto)
+ * or Bit 12 = 0x01000 = Force PCM bus into master mode. (otherwhise auto)
+ * Bit 13 = spare
+ * Bit 14 = 0x04000 = Use external ram (128K)
+ * Bit 15 = 0x08000 = Use external ram (512K)
+ * Bit 16 = 0x10000 = Use 64 timeslots instead of 32
+ * or Bit 17 = 0x20000 = Use 128 timeslots instead of anything else
+ * Bit 18 = spare
+ * Bit 19 = 0x80000 = Send the Watchdog a Signal (Dual E1 with Watchdog)
+ * (all other bits are reserved and shall be 0)
+ * example: 0x20204 one HFC-4S with dtmf detection and 128 timeslots on PCM
+ * bus (PCM master)
+ *
+ * port: (optional or required for all ports on all installed cards)
+ * HFC-4S/HFC-8S only bits:
+ * Bit 0 = 0x001 = Use master clock for this S/T interface
+ * (ony once per chip).
+ * Bit 1 = 0x002 = transmitter line setup (non capacitive mode)
+ * Don't use this unless you know what you are doing!
+ * Bit 2 = 0x004 = Disable E-channel. (No E-channel processing)
+ * example: 0x0001,0x0000,0x0000,0x0000 one HFC-4S with master clock
+ * received from port 1
+ *
+ * HFC-E1 only bits:
+ * Bit 0 = 0x0001 = interface: 0=copper, 1=optical
+ * Bit 1 = 0x0002 = reserved (later for 32 B-channels transparent mode)
+ * Bit 2 = 0x0004 = Report LOS
+ * Bit 3 = 0x0008 = Report AIS
+ * Bit 4 = 0x0010 = Report SLIP
+ * Bit 5 = 0x0020 = Report RDI
+ * Bit 8 = 0x0100 = Turn off CRC-4 Multiframe Mode, use double frame
+ * mode instead.
+ * Bit 9 = 0x0200 = Force get clock from interface, even in NT mode.
+ * or Bit 10 = 0x0400 = Force put clock to interface, even in TE mode.
+ * Bit 11 = 0x0800 = Use direct RX clock for PCM sync rather than PLL.
+ * (E1 only)
+ * Bit 12-13 = 0xX000 = elastic jitter buffer (1-3), Set both bits to 0
+ * for default.
+ * (all other bits are reserved and shall be 0)
+ *
+ * debug:
+ * NOTE: only one debug value must be given for all cards
+ * enable debugging (see hfc_multi.h for debug options)
+ *
+ * poll:
+ * NOTE: only one poll value must be given for all cards
+ * Give the number of samples for each fifo process.
+ * By default 128 is used. Decrease to reduce delay, increase to
+ * reduce cpu load. If unsure, don't mess with it!
+ * Valid is 8, 16, 32, 64, 128, 256.
+ *
+ * pcm:
+ * NOTE: only one pcm value must be given for every card.
+ * The PCM bus id tells the mISDNdsp module about the connected PCM bus.
+ * By default (0), the PCM bus id is 100 for the card that is PCM master.
+ * If multiple cards are PCM master (because they are not interconnected),
+ * each card with PCM master will have increasing PCM id.
+ * All PCM busses with the same ID are expected to be connected and have
+ * common time slots slots.
+ * Only one chip of the PCM bus must be master, the others slave.
+ * -1 means no support of PCM bus not even.
+ * Omit this value, if all cards are interconnected or none is connected.
+ * If unsure, don't give this parameter.
+ *
+ * dslot:
+ * NOTE: only one poll value must be given for every card.
+ * Also this value must be given for non-E1 cards. If omitted, the E1
+ * card has D-channel on time slot 16, which is default.
+ * If 1..15 or 17..31, an alternate time slot is used for D-channel.
+ * In this case, the application must be able to handle this.
+ * If -1 is given, the D-channel is disabled and all 31 slots can be used
+ * for B-channel. (only for specific applications)
+ * If you don't know how to use it, you don't need it!
+ *
+ * iomode:
+ * NOTE: only one mode value must be given for every card.
+ * -> See hfc_multi.h for HFC_IO_MODE_* values
+ * By default, the IO mode is pci memory IO (MEMIO).
+ * Some cards requre specific IO mode, so it cannot be changed.
+ * It may be usefull to set IO mode to register io (REGIO) to solve
+ * PCI bridge problems.
+ * If unsure, don't give this parameter.
+ *
+ * clockdelay_nt:
+ * NOTE: only one clockdelay_nt value must be given once for all cards.
+ * Give the value of the clock control register (A_ST_CLK_DLY)
+ * of the S/T interfaces in NT mode.
+ * This register is needed for the TBR3 certification, so don't change it.
+ *
+ * clockdelay_te:
+ * NOTE: only one clockdelay_te value must be given once
+ * Give the value of the clock control register (A_ST_CLK_DLY)
+ * of the S/T interfaces in TE mode.
+ * This register is needed for the TBR3 certification, so don't change it.
+ */
+
+/*
+ * debug register access (never use this, it will flood your system log)
+ * #define HFC_REGISTER_DEBUG
+ */
+
+static const char *hfcmulti_revision = "2.00";
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/mISDNhw.h>
+#include <linux/mISDNdsp.h>
+
+/*
+#define IRQCOUNT_DEBUG
+#define IRQ_DEBUG
+*/
+
+#include "hfc_multi.h"
+#ifdef ECHOPREP
+#include "gaintab.h"
+#endif
+
+#define MAX_CARDS 8
+#define MAX_PORTS (8 * MAX_CARDS)
+
+static LIST_HEAD(HFClist);
+static spinlock_t HFClock; /* global hfc list lock */
+
+static void ph_state_change(struct dchannel *);
+static void (*hfc_interrupt)(void);
+static void (*register_interrupt)(void);
+static int (*unregister_interrupt)(void);
+static int interrupt_registered;
+
+static struct hfc_multi *syncmaster;
+int plxsd_master; /* if we have a master card (yet) */
+static spinlock_t plx_lock; /* may not acquire other lock inside */
+EXPORT_SYMBOL(plx_lock);
+
+#define TYP_E1 1
+#define TYP_4S 4
+#define TYP_8S 8
+
+static int poll_timer = 6; /* default = 128 samples = 16ms */
+/* number of POLL_TIMER interrupts for G2 timeout (ca 1s) */
+static int nt_t1_count[] = { 3840, 1920, 960, 480, 240, 120, 60, 30 };
+#define CLKDEL_TE 0x0f /* CLKDEL in TE mode */
+#define CLKDEL_NT 0x6c /* CLKDEL in NT mode
+ (0x60 MUST be included!) */
+static u_char silence = 0xff; /* silence by LAW */
+
+#define DIP_4S 0x1 /* DIP Switches for Beronet 1S/2S/4S cards */
+#define DIP_8S 0x2 /* DIP Switches for Beronet 8S+ cards */
+#define DIP_E1 0x3 /* DIP Switches for Beronet E1 cards */
+
+/*
+ * module stuff
+ */
+
+static uint type[MAX_CARDS];
+static uint pcm[MAX_CARDS];
+static uint dslot[MAX_CARDS];
+static uint iomode[MAX_CARDS];
+static uint port[MAX_PORTS];
+static uint debug;
+static uint poll;
+static uint timer;
+static uint clockdelay_te = CLKDEL_TE;
+static uint clockdelay_nt = CLKDEL_NT;
+
+static int HFC_cnt, Port_cnt, PCM_cnt = 99;
+
+MODULE_AUTHOR("Andreas Eversberg");
+MODULE_LICENSE("GPL");
+module_param(debug, uint, S_IRUGO | S_IWUSR);
+module_param(poll, uint, S_IRUGO | S_IWUSR);
+module_param(timer, uint, S_IRUGO | S_IWUSR);
+module_param(clockdelay_te, uint, S_IRUGO | S_IWUSR);
+module_param(clockdelay_nt, uint, S_IRUGO | S_IWUSR);
+module_param_array(type, uint, NULL, S_IRUGO | S_IWUSR);
+module_param_array(pcm, uint, NULL, S_IRUGO | S_IWUSR);
+module_param_array(dslot, uint, NULL, S_IRUGO | S_IWUSR);
+module_param_array(iomode, uint, NULL, S_IRUGO | S_IWUSR);
+module_param_array(port, uint, NULL, S_IRUGO | S_IWUSR);
+
+#ifdef HFC_REGISTER_DEBUG
+#define HFC_outb(hc, reg, val) \
+ (hc->HFC_outb(hc, reg, val, __func__, __LINE__))
+#define HFC_outb_nodebug(hc, reg, val) \
+ (hc->HFC_outb_nodebug(hc, reg, val, __func__, __LINE__))
+#define HFC_inb(hc, reg) \
+ (hc->HFC_inb(hc, reg, __func__, __LINE__))
+#define HFC_inb_nodebug(hc, reg) \
+ (hc->HFC_inb_nodebug(hc, reg, __func__, __LINE__))
+#define HFC_inw(hc, reg) \
+ (hc->HFC_inw(hc, reg, __func__, __LINE__))
+#define HFC_inw_nodebug(hc, reg) \
+ (hc->HFC_inw_nodebug(hc, reg, __func__, __LINE__))
+#define HFC_wait(hc) \
+ (hc->HFC_wait(hc, __func__, __LINE__))
+#define HFC_wait_nodebug(hc) \
+ (hc->HFC_wait_nodebug(hc, __func__, __LINE__))
+#else
+#define HFC_outb(hc, reg, val) (hc->HFC_outb(hc, reg, val))
+#define HFC_outb_nodebug(hc, reg, val) (hc->HFC_outb_nodebug(hc, reg, val))
+#define HFC_inb(hc, reg) (hc->HFC_inb(hc, reg))
+#define HFC_inb_nodebug(hc, reg) (hc->HFC_inb_nodebug(hc, reg))
+#define HFC_inw(hc, reg) (hc->HFC_inw(hc, reg))
+#define HFC_inw_nodebug(hc, reg) (hc->HFC_inw_nodebug(hc, reg))
+#define HFC_wait(hc) (hc->HFC_wait(hc))
+#define HFC_wait_nodebug(hc) (hc->HFC_wait_nodebug(hc))
+#endif
+
+/* HFC_IO_MODE_PCIMEM */
+static void
+#ifdef HFC_REGISTER_DEBUG
+HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val,
+ const char *function, int line)
+#else
+HFC_outb_pcimem(struct hfc_multi *hc, u_char reg, u_char val)
+#endif
+{
+ writeb(val, (hc->pci_membase)+reg);
+}
+static u_char
+#ifdef HFC_REGISTER_DEBUG
+HFC_inb_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line)
+#else
+HFC_inb_pcimem(struct hfc_multi *hc, u_char reg)
+#endif
+{
+ return readb((hc->pci_membase)+reg);
+}
+static u_short
+#ifdef HFC_REGISTER_DEBUG
+HFC_inw_pcimem(struct hfc_multi *hc, u_char reg, const char *function, int line)
+#else
+HFC_inw_pcimem(struct hfc_multi *hc, u_char reg)
+#endif
+{
+ return readw((hc->pci_membase)+reg);
+}
+static void
+#ifdef HFC_REGISTER_DEBUG
+HFC_wait_pcimem(struct hfc_multi *hc, const char *function, int line)
+#else
+HFC_wait_pcimem(struct hfc_multi *hc)
+#endif
+{
+ while (readb((hc->pci_membase)+R_STATUS) & V_BUSY);
+}
+
+/* HFC_IO_MODE_REGIO */
+static void
+#ifdef HFC_REGISTER_DEBUG
+HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val,
+ const char *function, int line)
+#else
+HFC_outb_regio(struct hfc_multi *hc, u_char reg, u_char val)
+#endif
+{
+ outb(reg, (hc->pci_iobase)+4);
+ outb(val, hc->pci_iobase);
+}
+static u_char
+#ifdef HFC_REGISTER_DEBUG
+HFC_inb_regio(struct hfc_multi *hc, u_char reg, const char *function, int line)
+#else
+HFC_inb_regio(struct hfc_multi *hc, u_char reg)
+#endif
+{
+ outb(reg, (hc->pci_iobase)+4);
+ return inb(hc->pci_iobase);
+}
+static u_short
+#ifdef HFC_REGISTER_DEBUG
+HFC_inw_regio(struct hfc_multi *hc, u_char reg, const char *function, int line)
+#else
+HFC_inw_regio(struct hfc_multi *hc, u_char reg)
+#endif
+{
+ outb(reg, (hc->pci_iobase)+4);
+ return inw(hc->pci_iobase);
+}
+static void
+#ifdef HFC_REGISTER_DEBUG
+HFC_wait_regio(struct hfc_multi *hc, const char *function, int line)
+#else
+HFC_wait_regio(struct hfc_multi *hc)
+#endif
+{
+ outb(R_STATUS, (hc->pci_iobase)+4);
+ while (inb(hc->pci_iobase) & V_BUSY);
+}
+
+#ifdef HFC_REGISTER_DEBUG
+static void
+HFC_outb_debug(struct hfc_multi *hc, u_char reg, u_char val,
+ const char *function, int line)
+{
+ char regname[256] = "", bits[9] = "xxxxxxxx";
+ int i;
+
+ i = -1;
+ while (hfc_register_names[++i].name) {
+ if (hfc_register_names[i].reg == reg)
+ strcat(regname, hfc_register_names[i].name);
+ }
+ if (regname[0] == '\0')
+ strcpy(regname, "register");
+
+ bits[7] = '0'+(!!(val&1));
+ bits[6] = '0'+(!!(val&2));
+ bits[5] = '0'+(!!(val&4));
+ bits[4] = '0'+(!!(val&8));
+ bits[3] = '0'+(!!(val&16));
+ bits[2] = '0'+(!!(val&32));
+ bits[1] = '0'+(!!(val&64));
+ bits[0] = '0'+(!!(val&128));
+ printk(KERN_DEBUG
+ "HFC_outb(chip %d, %02x=%s, 0x%02x=%s); in %s() line %d\n",
+ hc->id, reg, regname, val, bits, function, line);
+ HFC_outb_nodebug(hc, reg, val);
+}
+static u_char
+HFC_inb_debug(struct hfc_multi *hc, u_char reg, const char *function, int line)
+{
+ char regname[256] = "", bits[9] = "xxxxxxxx";
+ u_char val = HFC_inb_nodebug(hc, reg);
+ int i;
+
+ i = 0;
+ while (hfc_register_names[i++].name)
+ ;
+ while (hfc_register_names[++i].name) {
+ if (hfc_register_names[i].reg == reg)
+ strcat(regname, hfc_register_names[i].name);
+ }
+ if (regname[0] == '\0')
+ strcpy(regname, "register");
+
+ bits[7] = '0'+(!!(val&1));
+ bits[6] = '0'+(!!(val&2));
+ bits[5] = '0'+(!!(val&4));
+ bits[4] = '0'+(!!(val&8));
+ bits[3] = '0'+(!!(val&16));
+ bits[2] = '0'+(!!(val&32));
+ bits[1] = '0'+(!!(val&64));
+ bits[0] = '0'+(!!(val&128));
+ printk(KERN_DEBUG
+ "HFC_inb(chip %d, %02x=%s) = 0x%02x=%s; in %s() line %d\n",
+ hc->id, reg, regname, val, bits, function, line);
+ return val;
+}
+static u_short
+HFC_inw_debug(struct hfc_multi *hc, u_char reg, const char *function, int line)
+{
+ char regname[256] = "";
+ u_short val = HFC_inw_nodebug(hc, reg);
+ int i;
+
+ i = 0;
+ while (hfc_register_names[i++].name)
+ ;
+ while (hfc_register_names[++i].name) {
+ if (hfc_register_names[i].reg == reg)
+ strcat(regname, hfc_register_names[i].name);
+ }
+ if (regname[0] == '\0')
+ strcpy(regname, "register");
+
+ printk(KERN_DEBUG
+ "HFC_inw(chip %d, %02x=%s) = 0x%04x; in %s() line %d\n",
+ hc->id, reg, regname, val, function, line);
+ return val;
+}
+static void
+HFC_wait_debug(struct hfc_multi *hc, const char *function, int line)
+{
+ printk(KERN_DEBUG "HFC_wait(chip %d); in %s() line %d\n",
+ hc->id, function, line);
+ HFC_wait_nodebug(hc);
+}
+#endif
+
+/* write fifo data (REGIO) */
+void
+write_fifo_regio(struct hfc_multi *hc, u_char *data, int len)
+{
+ outb(A_FIFO_DATA0, (hc->pci_iobase)+4);
+ while (len>>2) {
+ outl(*(u32 *)data, hc->pci_iobase);
+ data += 4;
+ len -= 4;
+ }
+ while (len>>1) {
+ outw(*(u16 *)data, hc->pci_iobase);
+ data += 2;
+ len -= 2;
+ }
+ while (len) {
+ outb(*data, hc->pci_iobase);
+ data++;
+ len--;
+ }
+}
+/* write fifo data (PCIMEM) */
+void
+write_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len)
+{
+ while (len>>2) {
+ writel(*(u32 *)data, (hc->pci_membase)+A_FIFO_DATA0);
+ data += 4;
+ len -= 4;
+ }
+ while (len>>1) {
+ writew(*(u16 *)data, (hc->pci_membase)+A_FIFO_DATA0);
+ data += 2;
+ len -= 2;
+ }
+ while (len) {
+ writeb(*data, (hc->pci_membase)+A_FIFO_DATA0);
+ data++;
+ len--;
+ }
+}
+/* read fifo data (REGIO) */
+void
+read_fifo_regio(struct hfc_multi *hc, u_char *data, int len)
+{
+ outb(A_FIFO_DATA0, (hc->pci_iobase)+4);
+ while (len>>2) {
+ *(u32 *)data = inl(hc->pci_iobase);
+ data += 4;
+ len -= 4;
+ }
+ while (len>>1) {
+ *(u16 *)data = inw(hc->pci_iobase);
+ data += 2;
+ len -= 2;
+ }
+ while (len) {
+ *data = inb(hc->pci_iobase);
+ data++;
+ len--;
+ }
+}
+
+/* read fifo data (PCIMEM) */
+void
+read_fifo_pcimem(struct hfc_multi *hc, u_char *data, int len)
+{
+ while (len>>2) {
+ *(u32 *)data =
+ readl((hc->pci_membase)+A_FIFO_DATA0);
+ data += 4;
+ len -= 4;
+ }
+ while (len>>1) {
+ *(u16 *)data =
+ readw((hc->pci_membase)+A_FIFO_DATA0);
+ data += 2;
+ len -= 2;
+ }
+ while (len) {
+ *data = readb((hc->pci_membase)+A_FIFO_DATA0);
+ data++;
+ len--;
+ }
+}
+
+
+static void
+enable_hwirq(struct hfc_multi *hc)
+{
+ hc->hw.r_irq_ctrl |= V_GLOB_IRQ_EN;
+ HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl);
+}
+
+static void
+disable_hwirq(struct hfc_multi *hc)
+{
+ hc->hw.r_irq_ctrl &= ~((u_char)V_GLOB_IRQ_EN);
+ HFC_outb(hc, R_IRQ_CTRL, hc->hw.r_irq_ctrl);
+}
+
+#define NUM_EC 2
+#define MAX_TDM_CHAN 32
+
+
+inline void
+enablepcibridge(struct hfc_multi *c)
+{
+ HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); /* was _io before */
+}
+
+inline void
+disablepcibridge(struct hfc_multi *c)
+{
+ HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x2); /* was _io before */
+}
+
+inline unsigned char
+readpcibridge(struct hfc_multi *hc, unsigned char address)
+{
+ unsigned short cipv;
+ unsigned char data;
+
+ if (!hc->pci_iobase)
+ return 0;
+
+ /* slow down a PCI read access by 1 PCI clock cycle */
+ HFC_outb(hc, R_CTRL, 0x4); /*was _io before*/
+
+ if (address == 0)
+ cipv = 0x4000;
+ else
+ cipv = 0x5800;
+
+ /* select local bridge port address by writing to CIP port */
+ /* data = HFC_inb(c, cipv); * was _io before */
+ outw(cipv, hc->pci_iobase + 4);
+ data = inb(hc->pci_iobase);
+
+ /* restore R_CTRL for normal PCI read cycle speed */
+ HFC_outb(hc, R_CTRL, 0x0); /* was _io before */
+
+ return data;
+}
+
+inline void
+writepcibridge(struct hfc_multi *hc, unsigned char address, unsigned char data)
+{
+ unsigned short cipv;
+ unsigned int datav;
+
+ if (!hc->pci_iobase)
+ return;
+
+ if (address == 0)
+ cipv = 0x4000;
+ else
+ cipv = 0x5800;
+
+ /* select local bridge port address by writing to CIP port */
+ outw(cipv, hc->pci_iobase + 4);
+ /* define a 32 bit dword with 4 identical bytes for write sequence */
+ datav = data | ((__u32) data << 8) | ((__u32) data << 16) |
+ ((__u32) data << 24);
+
+ /*
+ * write this 32 bit dword to the bridge data port
+ * this will initiate a write sequence of up to 4 writes to the same
+ * address on the local bus interface the number of write accesses
+ * is undefined but >=1 and depends on the next PCI transaction
+ * during write sequence on the local bus
+ */
+ outl(datav, hc->pci_iobase);
+}
+
+inline void
+cpld_set_reg(struct hfc_multi *hc, unsigned char reg)
+{
+ /* Do data pin read low byte */
+ HFC_outb(hc, R_GPIO_OUT1, reg);
+}
+
+inline void
+cpld_write_reg(struct hfc_multi *hc, unsigned char reg, unsigned char val)
+{
+ cpld_set_reg(hc, reg);
+
+ enablepcibridge(hc);
+ writepcibridge(hc, 1, val);
+ disablepcibridge(hc);
+
+ return;
+}
+
+inline unsigned char
+cpld_read_reg(struct hfc_multi *hc, unsigned char reg)
+{
+ unsigned char bytein;
+
+ cpld_set_reg(hc, reg);
+
+ /* Do data pin read low byte */
+ HFC_outb(hc, R_GPIO_OUT1, reg);
+
+ enablepcibridge(hc);
+ bytein = readpcibridge(hc, 1);
+ disablepcibridge(hc);
+
+ return bytein;
+}
+
+inline void
+vpm_write_address(struct hfc_multi *hc, unsigned short addr)
+{
+ cpld_write_reg(hc, 0, 0xff & addr);
+ cpld_write_reg(hc, 1, 0x01 & (addr >> 8));
+}
+
+inline unsigned short
+vpm_read_address(struct hfc_multi *c)
+{
+ unsigned short addr;
+ unsigned short highbit;
+
+ addr = cpld_read_reg(c, 0);
+ highbit = cpld_read_reg(c, 1);
+
+ addr = addr | (highbit << 8);
+
+ return addr & 0x1ff;
+}
+
+inline unsigned char
+vpm_in(struct hfc_multi *c, int which, unsigned short addr)
+{
+ unsigned char res;
+
+ vpm_write_address(c, addr);
+
+ if (!which)
+ cpld_set_reg(c, 2);
+ else
+ cpld_set_reg(c, 3);
+
+ enablepcibridge(c);
+ res = readpcibridge(c, 1);
+ disablepcibridge(c);
+
+ cpld_set_reg(c, 0);
+
+ return res;
+}
+
+inline void
+vpm_out(struct hfc_multi *c, int which, unsigned short addr,
+ unsigned char data)
+{
+ vpm_write_address(c, addr);
+
+ enablepcibridge(c);
+
+ if (!which)
+ cpld_set_reg(c, 2);
+ else
+ cpld_set_reg(c, 3);
+
+ writepcibridge(c, 1, data);
+
+ cpld_set_reg(c, 0);
+
+ disablepcibridge(c);
+
+ {
+ unsigned char regin;
+ regin = vpm_in(c, which, addr);
+ if (regin != data)
+ printk(KERN_DEBUG "Wrote 0x%x to register 0x%x but got back "
+ "0x%x\n", data, addr, regin);
+ }
+
+}
+
+
+void
+vpm_init(struct hfc_multi *wc)
+{
+ unsigned char reg;
+ unsigned int mask;
+ unsigned int i, x, y;
+ unsigned int ver;
+
+ for (x = 0; x < NUM_EC; x++) {
+ /* Setup GPIO's */
+ if (!x) {
+ ver = vpm_in(wc, x, 0x1a0);
+ printk(KERN_DEBUG "VPM: Chip %d: ver %02x\n", x, ver);
+ }
+
+ for (y = 0; y < 4; y++) {
+ vpm_out(wc, x, 0x1a8 + y, 0x00); /* GPIO out */
+ vpm_out(wc, x, 0x1ac + y, 0x00); /* GPIO dir */
+ vpm_out(wc, x, 0x1b0 + y, 0x00); /* GPIO sel */
+ }
+
+ /* Setup TDM path - sets fsync and tdm_clk as inputs */
+ reg = vpm_in(wc, x, 0x1a3); /* misc_con */
+ vpm_out(wc, x, 0x1a3, reg & ~2);
+
+ /* Setup Echo length (256 taps) */
+ vpm_out(wc, x, 0x022, 1);
+ vpm_out(wc, x, 0x023, 0xff);
+
+ /* Setup timeslots */
+ vpm_out(wc, x, 0x02f, 0x00);
+ mask = 0x02020202 << (x * 4);
+
+ /* Setup the tdm channel masks for all chips */
+ for (i = 0; i < 4; i++)
+ vpm_out(wc, x, 0x33 - i, (mask >> (i << 3)) & 0xff);
+
+ /* Setup convergence rate */
+ printk(KERN_DEBUG "VPM: A-law mode\n");
+ reg = 0x00 | 0x10 | 0x01;
+ vpm_out(wc, x, 0x20, reg);
+ printk(KERN_DEBUG "VPM reg 0x20 is %x\n", reg);
+ /*vpm_out(wc, x, 0x20, (0x00 | 0x08 | 0x20 | 0x10)); */
+
+ vpm_out(wc, x, 0x24, 0x02);
+ reg = vpm_in(wc, x, 0x24);
+ printk(KERN_DEBUG "NLP Thresh is set to %d (0x%x)\n", reg, reg);
+
+ /* Initialize echo cans */
+ for (i = 0; i < MAX_TDM_CHAN; i++) {
+ if (mask & (0x00000001 << i))
+ vpm_out(wc, x, i, 0x00);
+ }
+
+ /*
+ * ARM arch at least disallows a udelay of
+ * more than 2ms... it gives a fake "__bad_udelay"
+ * reference at link-time.
+ * long delays in kernel code are pretty sucky anyway
+ * for now work around it using 5 x 2ms instead of 1 x 10ms
+ */
+
+ udelay(2000);
+ udelay(2000);
+ udelay(2000);
+ udelay(2000);
+ udelay(2000);
+
+ /* Put in bypass mode */
+ for (i = 0; i < MAX_TDM_CHAN; i++) {
+ if (mask & (0x00000001 << i))
+ vpm_out(wc, x, i, 0x01);
+ }
+
+ /* Enable bypass */
+ for (i = 0; i < MAX_TDM_CHAN; i++) {
+ if (mask & (0x00000001 << i))
+ vpm_out(wc, x, 0x78 + i, 0x01);
+ }
+
+ }
+}
+
+void
+vpm_check(struct hfc_multi *hctmp)
+{
+ unsigned char gpi2;
+
+ gpi2 = HFC_inb(hctmp, R_GPI_IN2);
+
+ if ((gpi2 & 0x3) != 0x3)
+ printk(KERN_DEBUG "Got interrupt 0x%x from VPM!\n", gpi2);
+}
+
+
+/*
+ * Interface to enable/disable the HW Echocan
+ *
+ * these functions are called within a spin_lock_irqsave on
+ * the channel instance lock, so we are not disturbed by irqs
+ *
+ * we can later easily change the interface to make other
+ * things configurable, for now we configure the taps
+ *
+ */
+
+void
+vpm_echocan_on(struct hfc_multi *hc, int ch, int taps)
+{
+ unsigned int timeslot;
+ unsigned int unit;
+ struct bchannel *bch = hc->chan[ch].bch;
+#ifdef TXADJ
+ int txadj = -4;
+ struct sk_buff *skb;
+#endif
+ if (hc->chan[ch].protocol != ISDN_P_B_RAW)
+ return;
+
+ if (!bch)
+ return;
+
+#ifdef TXADJ
+ skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX,
+ sizeof(int), &txadj, GFP_ATOMIC);
+ if (skb)
+ recv_Bchannel_skb(bch, skb);
+#endif
+
+ timeslot = ((ch/4)*8) + ((ch%4)*4) + 1;
+ unit = ch % 4;
+
+ printk(KERN_NOTICE "vpm_echocan_on called taps [%d] on timeslot %d\n",
+ taps, timeslot);
+
+ vpm_out(hc, unit, timeslot, 0x7e);
+}
+
+void
+vpm_echocan_off(struct hfc_multi *hc, int ch)
+{
+ unsigned int timeslot;
+ unsigned int unit;
+ struct bchannel *bch = hc->chan[ch].bch;
+#ifdef TXADJ
+ int txadj = 0;
+ struct sk_buff *skb;
+#endif
+
+ if (hc->chan[ch].protocol != ISDN_P_B_RAW)
+ return;
+
+ if (!bch)
+ return;
+
+#ifdef TXADJ
+ skb = _alloc_mISDN_skb(PH_CONTROL_IND, HFC_VOL_CHANGE_TX,
+ sizeof(int), &txadj, GFP_ATOMIC);
+ if (skb)
+ recv_Bchannel_skb(bch, skb);
+#endif
+
+ timeslot = ((ch/4)*8) + ((ch%4)*4) + 1;
+ unit = ch % 4;
+
+ printk(KERN_NOTICE "vpm_echocan_off called on timeslot %d\n",
+ timeslot);
+ /* FILLME */
+ vpm_out(hc, unit, timeslot, 0x01);
+}
+
+
+/*
+ * Speech Design resync feature
+ * NOTE: This is called sometimes outside interrupt handler.
+ * We must lock irqsave, so no other interrupt (other card) will occurr!
+ * Also multiple interrupts may nest, so must lock each access (lists, card)!
+ */
+static inline void
+hfcmulti_resync(struct hfc_multi *locked, struct hfc_multi *newmaster, int rm)
+{
+ struct hfc_multi *hc, *next, *pcmmaster = 0;
+ u_int *plx_acc_32, pv;
+ u_long flags;
+
+ spin_lock_irqsave(&HFClock, flags);
+ spin_lock(&plx_lock); /* must be locked inside other locks */
+
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "%s: RESYNC(syncmaster=0x%p)\n",
+ __func__, syncmaster);
+
+ /* select new master */
+ if (newmaster) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "using provided controller\n");
+ } else {
+ list_for_each_entry_safe(hc, next, &HFClist, list) {
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ if (hc->syncronized) {
+ newmaster = hc;
+ break;
+ }
+ }
+ }
+ }
+
+ /* Disable sync of all cards */
+ list_for_each_entry_safe(hc, next, &HFClist, list) {
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv &= ~PLX_SYNC_O_EN;
+ writel(pv, plx_acc_32);
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) {
+ pcmmaster = hc;
+ if (hc->type == 1) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG
+ "Schedule SYNC_I\n");
+ hc->e1_resync |= 1; /* get SYNC_I */
+ }
+ }
+ }
+ }
+
+ if (newmaster) {
+ hc = newmaster;
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "id=%d (0x%p) = syncronized with "
+ "interface.\n", hc->id, hc);
+ /* Enable new sync master */
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv |= PLX_SYNC_O_EN;
+ writel(pv, plx_acc_32);
+ /* switch to jatt PLL, if not disabled by RX_SYNC */
+ if (hc->type == 1 && !test_bit(HFC_CHIP_RX_SYNC, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "Schedule jatt PLL\n");
+ hc->e1_resync |= 2; /* switch to jatt */
+ }
+ } else {
+ if (pcmmaster) {
+ hc = pcmmaster;
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG
+ "id=%d (0x%p) = PCM master syncronized "
+ "with QUARTZ\n", hc->id, hc);
+ if (hc->type == 1) {
+ /* Use the crystal clock for the PCM
+ master card */
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG
+ "Schedule QUARTZ for HFC-E1\n");
+ hc->e1_resync |= 4; /* switch quartz */
+ } else {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG
+ "QUARTZ is automatically "
+ "enabled by HFC-%dS\n", hc->type);
+ }
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv |= PLX_SYNC_O_EN;
+ writel(pv, plx_acc_32);
+ } else
+ if (!rm)
+ printk(KERN_ERR "%s no pcm master, this MUST "
+ "not happen!\n", __func__);
+ }
+ syncmaster = newmaster;
+
+ spin_unlock(&plx_lock);
+ spin_unlock_irqrestore(&HFClock, flags);
+}
+
+/* This must be called AND hc must be locked irqsave!!! */
+inline void
+plxsd_checksync(struct hfc_multi *hc, int rm)
+{
+ if (hc->syncronized) {
+ if (syncmaster == NULL) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_WARNING "%s: GOT sync on card %d"
+ " (id=%d)\n", __func__, hc->id + 1,
+ hc->id);
+ hfcmulti_resync(hc, hc, rm);
+ }
+ } else {
+ if (syncmaster == hc) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_WARNING "%s: LOST sync on card %d"
+ " (id=%d)\n", __func__, hc->id + 1,
+ hc->id);
+ hfcmulti_resync(hc, NULL, rm);
+ }
+ }
+}
+
+
+/*
+ * free hardware resources used by driver
+ */
+static void
+release_io_hfcmulti(struct hfc_multi *hc)
+{
+ u_int *plx_acc_32, pv;
+ u_long plx_flags;
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: entered\n", __func__);
+
+ /* soft reset also masks all interrupts */
+ hc->hw.r_cirm |= V_SRES;
+ HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
+ udelay(1000);
+ hc->hw.r_cirm &= ~V_SRES;
+ HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
+ udelay(1000); /* instead of 'wait' that may cause locking */
+
+ /* release Speech Design card, if PLX was initialized */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip) && hc->plx_membase) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "%s: release PLXSD card %d\n",
+ __func__, hc->id + 1);
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ writel(PLX_GPIOC_INIT, plx_acc_32);
+ pv = readl(plx_acc_32);
+ /* Termination off */
+ pv &= ~PLX_TERM_ON;
+ /* Disconnect the PCM */
+ pv |= PLX_SLAVE_EN_N;
+ pv &= ~PLX_MASTER_EN;
+ pv &= ~PLX_SYNC_O_EN;
+ /* Put the DSP in Reset */
+ pv &= ~PLX_DSP_RES_N;
+ writel(pv, plx_acc_32);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: PCM off: PLX_GPIO=%x\n",
+ __func__, pv);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ }
+
+ /* disable memory mapped ports / io ports */
+ test_and_clear_bit(HFC_CHIP_PLXSD, &hc->chip); /* prevent resync */
+ pci_write_config_word(hc->pci_dev, PCI_COMMAND, 0);
+ if (hc->pci_membase)
+ iounmap((void *)hc->pci_membase);
+ if (hc->plx_membase)
+ iounmap((void *)hc->plx_membase);
+ if (hc->pci_iobase)
+ release_region(hc->pci_iobase, 8);
+
+ if (hc->pci_dev) {
+ pci_disable_device(hc->pci_dev);
+ pci_set_drvdata(hc->pci_dev, NULL);
+ }
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: done\n", __func__);
+}
+
+/*
+ * function called to reset the HFC chip. A complete software reset of chip
+ * and fifos is done. All configuration of the chip is done.
+ */
+
+static int
+init_chip(struct hfc_multi *hc)
+{
+ u_long flags, val, val2 = 0, rev;
+ int i, err = 0;
+ u_char r_conf_en, rval;
+ u_int *plx_acc_32, pv;
+ u_long plx_flags, hfc_flags;
+ int plx_count;
+ struct hfc_multi *pos, *next, *plx_last_hc;
+
+ spin_lock_irqsave(&hc->lock, flags);
+ /* reset all registers */
+ memset(&hc->hw, 0, sizeof(struct hfcm_hw));
+
+ /* revision check */
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: entered\n", __func__);
+ val = HFC_inb(hc, R_CHIP_ID)>>4;
+ if (val != 0x8 && val != 0xc && val != 0xe) {
+ printk(KERN_INFO "HFC_multi: unknown CHIP_ID:%x\n", (u_int)val);
+ err = -EIO;
+ goto out;
+ }
+ rev = HFC_inb(hc, R_CHIP_RV);
+ printk(KERN_INFO
+ "HFC_multi: detected HFC with chip ID=0x%lx revision=%ld%s\n",
+ val, rev, (rev == 0) ? " (old FIFO handling)" : "");
+ if (rev == 0) {
+ test_and_set_bit(HFC_CHIP_REVISION0, &hc->chip);
+ printk(KERN_WARNING
+ "HFC_multi: NOTE: Your chip is revision 0, "
+ "ask Cologne Chip for update. Newer chips "
+ "have a better FIFO handling. Old chips "
+ "still work but may have slightly lower "
+ "HDLC transmit performance.\n");
+ }
+ if (rev > 1) {
+ printk(KERN_WARNING "HFC_multi: WARNING: This driver doesn't "
+ "consider chip revision = %ld. The chip / "
+ "bridge may not work.\n", rev);
+ }
+
+ /* set s-ram size */
+ hc->Flen = 0x10;
+ hc->Zmin = 0x80;
+ hc->Zlen = 384;
+ hc->DTMFbase = 0x1000;
+ if (test_bit(HFC_CHIP_EXRAM_128, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: changing to 128K extenal RAM\n",
+ __func__);
+ hc->hw.r_ctrl |= V_EXT_RAM;
+ hc->hw.r_ram_sz = 1;
+ hc->Flen = 0x20;
+ hc->Zmin = 0xc0;
+ hc->Zlen = 1856;
+ hc->DTMFbase = 0x2000;
+ }
+ if (test_bit(HFC_CHIP_EXRAM_512, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: changing to 512K extenal RAM\n",
+ __func__);
+ hc->hw.r_ctrl |= V_EXT_RAM;
+ hc->hw.r_ram_sz = 2;
+ hc->Flen = 0x20;
+ hc->Zmin = 0xc0;
+ hc->Zlen = 8000;
+ hc->DTMFbase = 0x2000;
+ }
+ hc->max_trans = poll << 1;
+ if (hc->max_trans > hc->Zlen)
+ hc->max_trans = hc->Zlen;
+
+ /* Speech Design PLX bridge */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "%s: initializing PLXSD card %d\n",
+ __func__, hc->id + 1);
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ writel(PLX_GPIOC_INIT, plx_acc_32);
+ pv = readl(plx_acc_32);
+ /* The first and the last cards are terminating the PCM bus */
+ pv |= PLX_TERM_ON; /* hc is currently the last */
+ /* Disconnect the PCM */
+ pv |= PLX_SLAVE_EN_N;
+ pv &= ~PLX_MASTER_EN;
+ pv &= ~PLX_SYNC_O_EN;
+ /* Put the DSP in Reset */
+ pv &= ~PLX_DSP_RES_N;
+ writel(pv, plx_acc_32);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: slave/term: PLX_GPIO=%x\n",
+ __func__, pv);
+ /*
+ * If we are the 3rd PLXSD card or higher, we must turn
+ * termination of last PLXSD card off.
+ */
+ spin_lock_irqsave(&HFClock, hfc_flags);
+ plx_count = 0;
+ plx_last_hc = NULL;
+ list_for_each_entry_safe(pos, next, &HFClist, list) {
+ if (test_bit(HFC_CHIP_PLXSD, &pos->chip)) {
+ plx_count++;
+ if (pos != hc)
+ plx_last_hc = pos;
+ }
+ }
+ if (plx_count >= 3) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "%s: card %d is between, so "
+ "we disable termination\n",
+ __func__, plx_last_hc->id + 1);
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(plx_last_hc->plx_membase
+ + PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv &= ~PLX_TERM_ON;
+ writel(pv, plx_acc_32);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: term off: PLX_GPIO=%x\n",
+ __func__, pv);
+ }
+ spin_unlock_irqrestore(&HFClock, hfc_flags);
+ hc->hw.r_pcm_md0 = V_F0_LEN; /* shift clock for DSP */
+ }
+
+ /* we only want the real Z2 read-pointer for revision > 0 */
+ if (!test_bit(HFC_CHIP_REVISION0, &hc->chip))
+ hc->hw.r_ram_sz |= V_FZ_MD;
+
+ /* select pcm mode */
+ if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: setting PCM into slave mode\n",
+ __func__);
+ } else
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip) && !plxsd_master) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: setting PCM into master mode\n",
+ __func__);
+ hc->hw.r_pcm_md0 |= V_PCM_MD;
+ } else {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: performing PCM auto detect\n",
+ __func__);
+ }
+
+ /* soft reset */
+ HFC_outb(hc, R_CTRL, hc->hw.r_ctrl);
+ HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz);
+ HFC_outb(hc, R_FIFO_MD, 0);
+ hc->hw.r_cirm = V_SRES | V_HFCRES | V_PCMRES | V_STRES | V_RLD_EPR;
+ HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
+ udelay(100);
+ hc->hw.r_cirm = 0;
+ HFC_outb(hc, R_CIRM, hc->hw.r_cirm);
+ udelay(100);
+ HFC_outb(hc, R_RAM_SZ, hc->hw.r_ram_sz);
+
+ /* Speech Design PLX bridge pcm and sync mode */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ /* Connect PCM */
+ if (hc->hw.r_pcm_md0 & V_PCM_MD) {
+ pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N;
+ pv |= PLX_SYNC_O_EN;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: master: PLX_GPIO=%x\n",
+ __func__, pv);
+ } else {
+ pv &= ~(PLX_MASTER_EN | PLX_SLAVE_EN_N);
+ pv &= ~PLX_SYNC_O_EN;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: slave: PLX_GPIO=%x\n",
+ __func__, pv);
+ }
+ writel(pv, plx_acc_32);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ }
+
+ /* PCM setup */
+ HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x90);
+ if (hc->slots == 32)
+ HFC_outb(hc, R_PCM_MD1, 0x00);
+ if (hc->slots == 64)
+ HFC_outb(hc, R_PCM_MD1, 0x10);
+ if (hc->slots == 128)
+ HFC_outb(hc, R_PCM_MD1, 0x20);
+ HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0xa0);
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
+ HFC_outb(hc, R_PCM_MD2, V_SYNC_SRC); /* sync via SYNC_I / O */
+ else
+ HFC_outb(hc, R_PCM_MD2, 0x00); /* sync from interface */
+ HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00);
+ for (i = 0; i < 256; i++) {
+ HFC_outb_nodebug(hc, R_SLOT, i);
+ HFC_outb_nodebug(hc, A_SL_CFG, 0);
+ HFC_outb_nodebug(hc, A_CONF, 0);
+ hc->slot_owner[i] = -1;
+ }
+
+ /* set clock speed */
+ if (test_bit(HFC_CHIP_CLOCK2, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: setting double clock\n", __func__);
+ HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK);
+ }
+
+ /* B410P GPIO */
+ if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
+ printk(KERN_NOTICE "Setting GPIOs\n");
+ HFC_outb(hc, R_GPIO_SEL, 0x30);
+ HFC_outb(hc, R_GPIO_EN1, 0x3);
+ udelay(1000);
+ printk(KERN_NOTICE "calling vpm_init\n");
+ vpm_init(hc);
+ }
+
+ /* check if R_F0_CNT counts (8 kHz frame count) */
+ val = HFC_inb(hc, R_F0_CNTL);
+ val += HFC_inb(hc, R_F0_CNTH) << 8;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "HFC_multi F0_CNT %ld after reset\n", val);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout((HZ/100)?:1); /* Timeout minimum 10ms */
+ spin_lock_irqsave(&hc->lock, flags);
+ val2 = HFC_inb(hc, R_F0_CNTL);
+ val2 += HFC_inb(hc, R_F0_CNTH) << 8;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "HFC_multi F0_CNT %ld after 10 ms (1st try)\n",
+ val2);
+ if (val2 >= val+8) { /* 1 ms */
+ /* it counts, so we keep the pcm mode */
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip))
+ printk(KERN_INFO "controller is PCM bus MASTER\n");
+ else
+ if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip))
+ printk(KERN_INFO "controller is PCM bus SLAVE\n");
+ else {
+ test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
+ printk(KERN_INFO "controller is PCM bus SLAVE "
+ "(auto detected)\n");
+ }
+ } else {
+ /* does not count */
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)) {
+controller_fail:
+ printk(KERN_ERR "HFC_multi ERROR, getting no 125us "
+ "pulse. Seems that controller fails.\n");
+ err = -EIO;
+ goto out;
+ }
+ if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
+ printk(KERN_INFO "controller is PCM bus SLAVE "
+ "(ignoring missing PCM clock)\n");
+ } else {
+ /* only one pcm master */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)
+ && plxsd_master) {
+ printk(KERN_ERR "HFC_multi ERROR, no clock "
+ "on another Speech Design card found. "
+ "Please be sure to connect PCM cable.\n");
+ err = -EIO;
+ goto out;
+ }
+ /* retry with master clock */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(hc->plx_membase +
+ PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv |= PLX_MASTER_EN | PLX_SLAVE_EN_N;
+ pv |= PLX_SYNC_O_EN;
+ writel(pv, plx_acc_32);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: master: PLX_GPIO"
+ "=%x\n", __func__, pv);
+ }
+ hc->hw.r_pcm_md0 |= V_PCM_MD;
+ HFC_outb(hc, R_PCM_MD0, hc->hw.r_pcm_md0 | 0x00);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout((HZ/100)?:1); /* Timeout min. 10ms */
+ spin_lock_irqsave(&hc->lock, flags);
+ val2 = HFC_inb(hc, R_F0_CNTL);
+ val2 += HFC_inb(hc, R_F0_CNTH) << 8;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "HFC_multi F0_CNT %ld after "
+ "10 ms (2nd try)\n", val2);
+ if (val2 >= val+8) { /* 1 ms */
+ test_and_set_bit(HFC_CHIP_PCM_MASTER,
+ &hc->chip);
+ printk(KERN_INFO "controller is PCM bus MASTER "
+ "(auto detected)\n");
+ } else
+ goto controller_fail;
+ }
+ }
+
+ /* Release the DSP Reset */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip))
+ plxsd_master = 1;
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc_32 = (u_int *)(hc->plx_membase+PLX_GPIOC);
+ pv = readl(plx_acc_32);
+ pv |= PLX_DSP_RES_N;
+ writel(pv, plx_acc_32);
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: reset off: PLX_GPIO=%x\n",
+ __func__, pv);
+ }
+
+ /* pcm id */
+ if (hc->pcm)
+ printk(KERN_INFO "controller has given PCM BUS ID %d\n",
+ hc->pcm);
+ else {
+ if (test_bit(HFC_CHIP_PCM_MASTER, &hc->chip)
+ || test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ PCM_cnt++; /* SD has proprietary bridging */
+ }
+ hc->pcm = PCM_cnt;
+ printk(KERN_INFO "controller has PCM BUS ID %d "
+ "(auto selected)\n", hc->pcm);
+ }
+
+ /* set up timer */
+ HFC_outb(hc, R_TI_WD, poll_timer);
+ hc->hw.r_irqmsk_misc |= V_TI_IRQMSK;
+
+ /*
+ * set up 125us interrupt, only if function pointer is available
+ * and module parameter timer is set
+ */
+ if (timer && hfc_interrupt && register_interrupt) {
+ /* only one chip should use this interrupt */
+ timer = 0;
+ interrupt_registered = 1;
+ hc->hw.r_irqmsk_misc |= V_PROC_IRQMSK;
+ /* deactivate other interrupts in ztdummy */
+ register_interrupt();
+ }
+
+ /* set E1 state machine IRQ */
+ if (hc->type == 1)
+ hc->hw.r_irqmsk_misc |= V_STA_IRQMSK;
+
+ /* set DTMF detection */
+ if (test_bit(HFC_CHIP_DTMF, &hc->chip)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: enabling DTMF detection "
+ "for all B-channel\n", __func__);
+ hc->hw.r_dtmf = V_DTMF_EN | V_DTMF_STOP;
+ if (test_bit(HFC_CHIP_ULAW, &hc->chip))
+ hc->hw.r_dtmf |= V_ULAW_SEL;
+ HFC_outb(hc, R_DTMF_N, 102 - 1);
+ hc->hw.r_irqmsk_misc |= V_DTMF_IRQMSK;
+ }
+
+ /* conference engine */
+ if (test_bit(HFC_CHIP_ULAW, &hc->chip))
+ r_conf_en = V_CONF_EN | V_ULAW;
+ else
+ r_conf_en = V_CONF_EN;
+ HFC_outb(hc, R_CONF_EN, r_conf_en);
+
+ /* setting leds */
+ switch (hc->leds) {
+ case 1: /* HFC-E1 OEM */
+ if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip))
+ HFC_outb(hc, R_GPIO_SEL, 0x32);
+ else
+ HFC_outb(hc, R_GPIO_SEL, 0x30);
+
+ HFC_outb(hc, R_GPIO_EN1, 0x0f);
+ HFC_outb(hc, R_GPIO_OUT1, 0x00);
+
+ HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3);
+ break;
+
+ case 2: /* HFC-4S OEM */
+ case 3:
+ HFC_outb(hc, R_GPIO_SEL, 0xf0);
+ HFC_outb(hc, R_GPIO_EN1, 0xff);
+ HFC_outb(hc, R_GPIO_OUT1, 0x00);
+ break;
+ }
+
+ /* set master clock */
+ if (hc->masterclk >= 0) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: setting ST master clock "
+ "to port %d (0..%d)\n",
+ __func__, hc->masterclk, hc->ports-1);
+ hc->hw.r_st_sync = hc->masterclk | V_AUTO_SYNC;
+ HFC_outb(hc, R_ST_SYNC, hc->hw.r_st_sync);
+ }
+
+ /* setting misc irq */
+ HFC_outb(hc, R_IRQMSK_MISC, hc->hw.r_irqmsk_misc);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "r_irqmsk_misc.2: 0x%x\n",
+ hc->hw.r_irqmsk_misc);
+
+ /* RAM access test */
+ HFC_outb(hc, R_RAM_ADDR0, 0);
+ HFC_outb(hc, R_RAM_ADDR1, 0);
+ HFC_outb(hc, R_RAM_ADDR2, 0);
+ for (i = 0; i < 256; i++) {
+ HFC_outb_nodebug(hc, R_RAM_ADDR0, i);
+ HFC_outb_nodebug(hc, R_RAM_DATA, ((i*3)&0xff));
+ }
+ for (i = 0; i < 256; i++) {
+ HFC_outb_nodebug(hc, R_RAM_ADDR0, i);
+ HFC_inb_nodebug(hc, R_RAM_DATA);
+ rval = HFC_inb_nodebug(hc, R_INT_DATA);
+ if (rval != ((i * 3) & 0xff)) {
+ printk(KERN_DEBUG
+ "addr:%x val:%x should:%x\n", i, rval,
+ (i * 3) & 0xff);
+ err++;
+ }
+ }
+ if (err) {
+ printk(KERN_DEBUG "aborting - %d RAM access errors\n", err);
+ err = -EIO;
+ goto out;
+ }
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: done\n", __func__);
+out:
+ spin_unlock_irqrestore(&hc->lock, flags);
+ return err;
+}
+
+
+/*
+ * control the watchdog
+ */
+static void
+hfcmulti_watchdog(struct hfc_multi *hc)
+{
+ hc->wdcount++;
+
+ if (hc->wdcount > 10) {
+ hc->wdcount = 0;
+ hc->wdbyte = hc->wdbyte == V_GPIO_OUT2 ?
+ V_GPIO_OUT3 : V_GPIO_OUT2;
+
+ /* printk("Sending Watchdog Kill %x\n",hc->wdbyte); */
+ HFC_outb(hc, R_GPIO_EN0, V_GPIO_EN2 | V_GPIO_EN3);
+ HFC_outb(hc, R_GPIO_OUT0, hc->wdbyte);
+ }
+}
+
+
+
+/*
+ * output leds
+ */
+static void
+hfcmulti_leds(struct hfc_multi *hc)
+{
+ unsigned long lled;
+ unsigned long leddw;
+ int i, state, active, leds;
+ struct dchannel *dch;
+ int led[4];
+
+ hc->ledcount += poll;
+ if (hc->ledcount > 4096) {
+ hc->ledcount -= 4096;
+ hc->ledstate = 0xAFFEAFFE;
+ }
+
+ switch (hc->leds) {
+ case 1: /* HFC-E1 OEM */
+ /* 2 red blinking: NT mode deactivate
+ * 2 red steady: TE mode deactivate
+ * left green: L1 active
+ * left red: frame sync, but no L1
+ * right green: L2 active
+ */
+ if (hc->chan[hc->dslot].sync != 2) { /* no frame sync */
+ if (hc->chan[hc->dslot].dch->dev.D.protocol
+ != ISDN_P_NT_E1) {
+ led[0] = 1;
+ led[1] = 1;
+ } else if (hc->ledcount>>11) {
+ led[0] = 1;
+ led[1] = 1;
+ } else {
+ led[0] = 0;
+ led[1] = 0;
+ }
+ led[2] = 0;
+ led[3] = 0;
+ } else { /* with frame sync */
+ /* TODO make it work */
+ led[0] = 0;
+ led[1] = 0;
+ led[2] = 0;
+ led[3] = 1;
+ }
+ leds = (led[0] | (led[1]<<2) | (led[2]<<1) | (led[3]<<3))^0xF;
+ /* leds are inverted */
+ if (leds != (int)hc->ledstate) {
+ HFC_outb_nodebug(hc, R_GPIO_OUT1, leds);
+ hc->ledstate = leds;
+ }
+ break;
+
+ case 2: /* HFC-4S OEM */
+ /* red blinking = PH_DEACTIVATE NT Mode
+ * red steady = PH_DEACTIVATE TE Mode
+ * green steady = PH_ACTIVATE
+ */
+ for (i = 0; i < 4; i++) {
+ state = 0;
+ active = -1;
+ dch = hc->chan[(i << 2) | 2].dch;
+ if (dch) {
+ state = dch->state;
+ if (dch->dev.D.protocol == ISDN_P_NT_S0)
+ active = 3;
+ else
+ active = 7;
+ }
+ if (state) {
+ if (state == active) {
+ led[i] = 1; /* led green */
+ } else
+ if (dch->dev.D.protocol == ISDN_P_TE_S0)
+ /* TE mode: led red */
+ led[i] = 2;
+ else
+ if (hc->ledcount>>11)
+ /* led red */
+ led[i] = 2;
+ else
+ /* led off */
+ led[i] = 0;
+ } else
+ led[i] = 0; /* led off */
+ }
+ if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
+ leds = 0;
+ for (i = 0; i < 4; i++) {
+ if (led[i] == 1) {
+ /*green*/
+ leds |= (0x2 << (i * 2));
+ } else if (led[i] == 2) {
+ /*red*/
+ leds |= (0x1 << (i * 2));
+ }
+ }
+ if (leds != (int)hc->ledstate) {
+ vpm_out(hc, 0, 0x1a8 + 3, leds);
+ hc->ledstate = leds;
+ }
+ } else {
+ leds = ((led[3] > 0) << 0) | ((led[1] > 0) << 1) |
+ ((led[0] > 0) << 2) | ((led[2] > 0) << 3) |
+ ((led[3] & 1) << 4) | ((led[1] & 1) << 5) |
+ ((led[0] & 1) << 6) | ((led[2] & 1) << 7);
+ if (leds != (int)hc->ledstate) {
+ HFC_outb_nodebug(hc, R_GPIO_EN1, leds & 0x0F);
+ HFC_outb_nodebug(hc, R_GPIO_OUT1, leds >> 4);
+ hc->ledstate = leds;
+ }
+ }
+ break;
+
+ case 3: /* HFC 1S/2S Beronet */
+ /* red blinking = PH_DEACTIVATE NT Mode
+ * red steady = PH_DEACTIVATE TE Mode
+ * green steady = PH_ACTIVATE
+ */
+ for (i = 0; i < 2; i++) {
+ state = 0;
+ active = -1;
+ dch = hc->chan[(i << 2) | 2].dch;
+ if (dch) {
+ state = dch->state;
+ if (dch->dev.D.protocol == ISDN_P_NT_S0)
+ active = 3;
+ else
+ active = 7;
+ }
+ if (state) {
+ if (state == active) {
+ led[i] = 1; /* led green */
+ } else
+ if (dch->dev.D.protocol == ISDN_P_TE_S0)
+ /* TE mode: led red */
+ led[i] = 2;
+ else
+ if (hc->ledcount >> 11)
+ /* led red */
+ led[i] = 2;
+ else
+ /* led off */
+ led[i] = 0;
+ } else
+ led[i] = 0; /* led off */
+ }
+
+
+ leds = (led[0] > 0) | ((led[1] > 0)<<1) | ((led[0]&1)<<2)
+ | ((led[1]&1)<<3);
+ if (leds != (int)hc->ledstate) {
+ HFC_outb_nodebug(hc, R_GPIO_EN1,
+ ((led[0] > 0) << 2) | ((led[1] > 0) << 3));
+ HFC_outb_nodebug(hc, R_GPIO_OUT1,
+ ((led[0] & 1) << 2) | ((led[1] & 1) << 3));
+ hc->ledstate = leds;
+ }
+ break;
+ case 8: /* HFC 8S+ Beronet */
+ lled = 0;
+
+ for (i = 0; i < 8; i++) {
+ state = 0;
+ active = -1;
+ dch = hc->chan[(i << 2) | 2].dch;
+ if (dch) {
+ state = dch->state;
+ if (dch->dev.D.protocol == ISDN_P_NT_S0)
+ active = 3;
+ else
+ active = 7;
+ }
+ if (state) {
+ if (state == active) {
+ lled |= 0 << i;
+ } else
+ if (hc->ledcount >> 11)
+ lled |= 0 << i;
+ else
+ lled |= 1 << i;
+ } else
+ lled |= 1 << i;
+ }
+ leddw = lled << 24 | lled << 16 | lled << 8 | lled;
+ if (leddw != hc->ledstate) {
+ /* HFC_outb(hc, R_BRG_PCM_CFG, 1);
+ HFC_outb(c, R_BRG_PCM_CFG, (0x0 << 6) | 0x3); */
+ /* was _io before */
+ HFC_outb_nodebug(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK);
+ outw(0x4000, hc->pci_iobase + 4);
+ outl(leddw, hc->pci_iobase);
+ HFC_outb_nodebug(hc, R_BRG_PCM_CFG, V_PCM_CLK);
+ hc->ledstate = leddw;
+ }
+ break;
+ }
+}
+/*
+ * read dtmf coefficients
+ */
+
+static void
+hfcmulti_dtmf(struct hfc_multi *hc)
+{
+ s32 *coeff;
+ u_int mantissa;
+ int co, ch;
+ struct bchannel *bch = NULL;
+ u8 exponent;
+ int dtmf = 0;
+ int addr;
+ u16 w_float;
+ struct sk_buff *skb;
+ struct mISDNhead *hh;
+
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk(KERN_DEBUG "%s: dtmf detection irq\n", __func__);
+ for (ch = 0; ch <= 31; ch++) {
+ /* only process enabled B-channels */
+ bch = hc->chan[ch].bch;
+ if (!bch)
+ continue;
+ if (!hc->created[hc->chan[ch].port])
+ continue;
+ if (!test_bit(FLG_TRANSPARENT, &bch->Flags))
+ continue;
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk(KERN_DEBUG "%s: dtmf channel %d:",
+ __func__, ch);
+ coeff = &(hc->chan[ch].coeff[hc->chan[ch].coeff_count * 16]);
+ dtmf = 1;
+ for (co = 0; co < 8; co++) {
+ /* read W(n-1) coefficient */
+ addr = hc->DTMFbase + ((co<<7) | (ch<<2));
+ HFC_outb_nodebug(hc, R_RAM_ADDR0, addr);
+ HFC_outb_nodebug(hc, R_RAM_ADDR1, addr>>8);
+ HFC_outb_nodebug(hc, R_RAM_ADDR2, (addr>>16)
+ | V_ADDR_INC);
+ w_float = HFC_inb_nodebug(hc, R_RAM_DATA);
+ w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8);
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk(" %04x", w_float);
+
+ /* decode float (see chip doc) */
+ mantissa = w_float & 0x0fff;
+ if (w_float & 0x8000)
+ mantissa |= 0xfffff000;
+ exponent = (w_float>>12) & 0x7;
+ if (exponent) {
+ mantissa ^= 0x1000;
+ mantissa <<= (exponent-1);
+ }
+
+ /* store coefficient */
+ coeff[co<<1] = mantissa;
+
+ /* read W(n) coefficient */
+ w_float = HFC_inb_nodebug(hc, R_RAM_DATA);
+ w_float |= (HFC_inb_nodebug(hc, R_RAM_DATA) << 8);
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk(" %04x", w_float);
+
+ /* decode float (see chip doc) */
+ mantissa = w_float & 0x0fff;
+ if (w_float & 0x8000)
+ mantissa |= 0xfffff000;
+ exponent = (w_float>>12) & 0x7;
+ if (exponent) {
+ mantissa ^= 0x1000;
+ mantissa <<= (exponent-1);
+ }
+
+ /* store coefficient */
+ coeff[(co<<1)|1] = mantissa;
+ }
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk("%s: DTMF ready %08x %08x %08x %08x "
+ "%08x %08x %08x %08x\n", __func__,
+ coeff[0], coeff[1], coeff[2], coeff[3],
+ coeff[4], coeff[5], coeff[6], coeff[7]);
+ hc->chan[ch].coeff_count++;
+ if (hc->chan[ch].coeff_count == 8) {
+ hc->chan[ch].coeff_count = 0;
+ skb = mI_alloc_skb(512, GFP_ATOMIC);
+ if (!skb) {
+ printk(KERN_WARNING "%s: No memory for skb\n",
+ __func__);
+ continue;
+ }
+ hh = mISDN_HEAD_P(skb);
+ hh->prim = PH_CONTROL_IND;
+ hh->id = DTMF_HFC_COEF;
+ memcpy(skb_put(skb, 512), hc->chan[ch].coeff, 512);
+ recv_Bchannel_skb(bch, skb);
+ }
+ }
+
+ /* restart DTMF processing */
+ hc->dtmf = dtmf;
+ if (dtmf)
+ HFC_outb_nodebug(hc, R_DTMF, hc->hw.r_dtmf | V_RST_DTMF);
+}
+
+
+/*
+ * fill fifo as much as possible
+ */
+
+static void
+hfcmulti_tx(struct hfc_multi *hc, int ch)
+{
+ int i, ii, temp, len = 0;
+ int Zspace, z1, z2; /* must be int for calculation */
+ int Fspace, f1, f2;
+ u_char *d;
+ int *txpending, slot_tx;
+ struct bchannel *bch;
+ struct dchannel *dch;
+ struct sk_buff **sp = NULL;
+ int *idxp;
+
+ bch = hc->chan[ch].bch;
+ dch = hc->chan[ch].dch;
+ if ((!dch) && (!bch))
+ return;
+
+ txpending = &hc->chan[ch].txpending;
+ slot_tx = hc->chan[ch].slot_tx;
+ if (dch) {
+ if (!test_bit(FLG_ACTIVE, &dch->Flags))
+ return;
+ sp = &dch->tx_skb;
+ idxp = &dch->tx_idx;
+ } else {
+ if (!test_bit(FLG_ACTIVE, &bch->Flags))
+ return;
+ sp = &bch->tx_skb;
+ idxp = &bch->tx_idx;
+ }
+ if (*sp)
+ len = (*sp)->len;
+
+ if ((!len) && *txpending != 1)
+ return; /* no data */
+
+ if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
+ (hc->chan[ch].protocol == ISDN_P_B_RAW) &&
+ (hc->chan[ch].slot_rx < 0) &&
+ (hc->chan[ch].slot_tx < 0))
+ HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch << 1));
+ else
+ HFC_outb_nodebug(hc, R_FIFO, ch << 1);
+ HFC_wait_nodebug(hc);
+
+ if (*txpending == 2) {
+ /* reset fifo */
+ HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait_nodebug(hc);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ *txpending = 1;
+ }
+next_frame:
+ if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
+ f1 = HFC_inb_nodebug(hc, A_F1);
+ f2 = HFC_inb_nodebug(hc, A_F2);
+ while (f2 != (temp = HFC_inb_nodebug(hc, A_F2))) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG
+ "%s(card %d): reread f2 because %d!=%d\n",
+ __func__, hc->id + 1, temp, f2);
+ f2 = temp; /* repeat until F2 is equal */
+ }
+ Fspace = f2 - f1 - 1;
+ if (Fspace < 0)
+ Fspace += hc->Flen;
+ /*
+ * Old FIFO handling doesn't give us the current Z2 read
+ * pointer, so we cannot send the next frame before the fifo
+ * is empty. It makes no difference except for a slightly
+ * lower performance.
+ */
+ if (test_bit(HFC_CHIP_REVISION0, &hc->chip)) {
+ if (f1 != f2)
+ Fspace = 0;
+ else
+ Fspace = 1;
+ }
+ /* one frame only for ST D-channels, to allow resending */
+ if (hc->type != 1 && dch) {
+ if (f1 != f2)
+ Fspace = 0;
+ }
+ /* F-counter full condition */
+ if (Fspace == 0)
+ return;
+ }
+ z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin;
+ z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin;
+ while (z2 != (temp = (HFC_inw_nodebug(hc, A_Z2) - hc->Zmin))) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG "%s(card %d): reread z2 because "
+ "%d!=%d\n", __func__, hc->id + 1, temp, z2);
+ z2 = temp; /* repeat unti Z2 is equal */
+ }
+ Zspace = z2 - z1;
+ if (Zspace <= 0)
+ Zspace += hc->Zlen;
+ Zspace -= 4; /* keep not too full, so pointers will not overrun */
+ /* fill transparent data only to maxinum transparent load (minus 4) */
+ if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags))
+ Zspace = Zspace - hc->Zlen + hc->max_trans;
+ if (Zspace <= 0) /* no space of 4 bytes */
+ return;
+
+ /* if no data */
+ if (!len) {
+ if (z1 == z2) { /* empty */
+ /* if done with FIFO audio data during PCM connection */
+ if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) &&
+ *txpending && slot_tx >= 0) {
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG
+ "%s: reconnecting PCM due to no "
+ "more FIFO data: channel %d "
+ "slot_tx %d\n",
+ __func__, ch, slot_tx);
+ /* connect slot */
+ HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 |
+ V_HDLC_TRP | V_IFF);
+ HFC_outb_nodebug(hc, R_FIFO, ch<<1 | 1);
+ HFC_wait_nodebug(hc);
+ HFC_outb(hc, A_CON_HDLC, 0xc0 | 0x00 |
+ V_HDLC_TRP | V_IFF);
+ HFC_outb_nodebug(hc, R_FIFO, ch<<1);
+ HFC_wait_nodebug(hc);
+ }
+ *txpending = 0;
+ }
+ return; /* no data */
+ }
+
+ /* if audio data and connected slot */
+ if (bch && (!test_bit(FLG_HDLC, &bch->Flags)) && (!*txpending)
+ && slot_tx >= 0) {
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG "%s: disconnecting PCM due to "
+ "FIFO data: channel %d slot_tx %d\n",
+ __func__, ch, slot_tx);
+ /* disconnect slot */
+ HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 | V_HDLC_TRP | V_IFF);
+ HFC_outb_nodebug(hc, R_FIFO, ch<<1 | 1);
+ HFC_wait_nodebug(hc);
+ HFC_outb(hc, A_CON_HDLC, 0x80 | 0x00 | V_HDLC_TRP | V_IFF);
+ HFC_outb_nodebug(hc, R_FIFO, ch<<1);
+ HFC_wait_nodebug(hc);
+ }
+ *txpending = 1;
+
+ /* show activity */
+ hc->activity[hc->chan[ch].port] = 1;
+
+ /* fill fifo to what we have left */
+ ii = len;
+ if (dch || test_bit(FLG_HDLC, &bch->Flags))
+ temp = 1;
+ else
+ temp = 0;
+ i = *idxp;
+ d = (*sp)->data + i;
+ if (ii - i > Zspace)
+ ii = Zspace + i;
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG "%s(card %d): fifo(%d) has %d bytes space "
+ "left (z1=%04x, z2=%04x) sending %d of %d bytes %s\n",
+ __func__, hc->id + 1, ch, Zspace, z1, z2, ii-i, len-i,
+ temp ? "HDLC":"TRANS");
+
+
+ /* Have to prep the audio data */
+ hc->write_fifo(hc, d, ii - i);
+ *idxp = ii;
+
+ /* if not all data has been written */
+ if (ii != len) {
+ /* NOTE: fifo is started by the calling function */
+ return;
+ }
+
+ /* if all data has been written, terminate frame */
+ if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
+ /* increment f-counter */
+ HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F);
+ HFC_wait_nodebug(hc);
+ }
+
+ /* send confirm, since get_net_bframe will not do it with trans */
+ if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags))
+ confirm_Bsend(bch);
+
+ /* check for next frame */
+ dev_kfree_skb(*sp);
+ if (bch && get_next_bframe(bch)) { /* hdlc is confirmed here */
+ len = (*sp)->len;
+ goto next_frame;
+ }
+ if (dch && get_next_dframe(dch)) {
+ len = (*sp)->len;
+ goto next_frame;
+ }
+
+ /*
+ * now we have no more data, so in case of transparent,
+ * we set the last byte in fifo to 'silence' in case we will get
+ * no more data at all. this prevents sending an undefined value.
+ */
+ if (bch && test_bit(FLG_TRANSPARENT, &bch->Flags))
+ HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, silence);
+}
+
+
+/* NOTE: only called if E1 card is in active state */
+static void
+hfcmulti_rx(struct hfc_multi *hc, int ch)
+{
+ int temp;
+ int Zsize, z1, z2 = 0; /* = 0, to make GCC happy */
+ int f1 = 0, f2 = 0; /* = 0, to make GCC happy */
+ int again = 0;
+ struct bchannel *bch;
+ struct dchannel *dch;
+ struct sk_buff *skb, **sp = NULL;
+ int maxlen;
+
+ bch = hc->chan[ch].bch;
+ dch = hc->chan[ch].dch;
+ if ((!dch) && (!bch))
+ return;
+ if (dch) {
+ if (!test_bit(FLG_ACTIVE, &dch->Flags))
+ return;
+ sp = &dch->rx_skb;
+ maxlen = dch->maxlen;
+ } else {
+ if (!test_bit(FLG_ACTIVE, &bch->Flags))
+ return;
+ sp = &bch->rx_skb;
+ maxlen = bch->maxlen;
+ }
+next_frame:
+ /* on first AND before getting next valid frame, R_FIFO must be written
+ to. */
+ if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
+ (hc->chan[ch].protocol == ISDN_P_B_RAW) &&
+ (hc->chan[ch].slot_rx < 0) &&
+ (hc->chan[ch].slot_tx < 0))
+ HFC_outb_nodebug(hc, R_FIFO, 0x20 | (ch<<1) | 1);
+ else
+ HFC_outb_nodebug(hc, R_FIFO, (ch<<1)|1);
+ HFC_wait_nodebug(hc);
+
+ /* ignore if rx is off BUT change fifo (above) to start pending TX */
+ if (hc->chan[ch].rx_off)
+ return;
+
+ if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
+ f1 = HFC_inb_nodebug(hc, A_F1);
+ while (f1 != (temp = HFC_inb_nodebug(hc, A_F1))) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG
+ "%s(card %d): reread f1 because %d!=%d\n",
+ __func__, hc->id + 1, temp, f1);
+ f1 = temp; /* repeat until F1 is equal */
+ }
+ f2 = HFC_inb_nodebug(hc, A_F2);
+ }
+ z1 = HFC_inw_nodebug(hc, A_Z1) - hc->Zmin;
+ while (z1 != (temp = (HFC_inw_nodebug(hc, A_Z1) - hc->Zmin))) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG "%s(card %d): reread z2 because "
+ "%d!=%d\n", __func__, hc->id + 1, temp, z2);
+ z1 = temp; /* repeat until Z1 is equal */
+ }
+ z2 = HFC_inw_nodebug(hc, A_Z2) - hc->Zmin;
+ Zsize = z1 - z2;
+ if ((dch || test_bit(FLG_HDLC, &bch->Flags)) && f1 != f2)
+ /* complete hdlc frame */
+ Zsize++;
+ if (Zsize < 0)
+ Zsize += hc->Zlen;
+ /* if buffer is empty */
+ if (Zsize <= 0)
+ return;
+
+ if (*sp == NULL) {
+ *sp = mI_alloc_skb(maxlen + 3, GFP_ATOMIC);
+ if (*sp == NULL) {
+ printk(KERN_DEBUG "%s: No mem for rx_skb\n",
+ __func__);
+ return;
+ }
+ }
+ /* show activity */
+ hc->activity[hc->chan[ch].port] = 1;
+
+ /* empty fifo with what we have */
+ if (dch || test_bit(FLG_HDLC, &bch->Flags)) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG "%s(card %d): fifo(%d) reading %d "
+ "bytes (z1=%04x, z2=%04x) HDLC %s (f1=%d, f2=%d) "
+ "got=%d (again %d)\n", __func__, hc->id + 1, ch,
+ Zsize, z1, z2, (f1 == f2) ? "fragment" : "COMPLETE",
+ f1, f2, Zsize + (*sp)->len, again);
+ /* HDLC */
+ if ((Zsize + (*sp)->len) > (maxlen + 3)) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG
+ "%s(card %d): hdlc-frame too large.\n",
+ __func__, hc->id + 1);
+ skb_trim(*sp, 0);
+ HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait_nodebug(hc);
+ return;
+ }
+
+ hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize);
+
+ if (f1 != f2) {
+ /* increment Z2,F2-counter */
+ HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_INC_F);
+ HFC_wait_nodebug(hc);
+ /* check size */
+ if ((*sp)->len < 4) {
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG
+ "%s(card %d): Frame below minimum "
+ "size\n", __func__, hc->id + 1);
+ skb_trim(*sp, 0);
+ goto next_frame;
+ }
+ /* there is at least one complete frame, check crc */
+ if ((*sp)->data[(*sp)->len - 1]) {
+ if (debug & DEBUG_HFCMULTI_CRC)
+ printk(KERN_DEBUG
+ "%s: CRC-error\n", __func__);
+ skb_trim(*sp, 0);
+ goto next_frame;
+ }
+ skb_trim(*sp, (*sp)->len - 3);
+ if ((*sp)->len < MISDN_COPY_SIZE) {
+ skb = *sp;
+ *sp = mI_alloc_skb(skb->len, GFP_ATOMIC);
+ if (*sp) {
+ memcpy(skb_put(*sp, skb->len),
+ skb->data, skb->len);
+ skb_trim(skb, 0);
+ } else {
+ printk(KERN_DEBUG "%s: No mem\n",
+ __func__);
+ *sp = skb;
+ skb = NULL;
+ }
+ } else {
+ skb = NULL;
+ }
+ if (debug & DEBUG_HFCMULTI_FIFO) {
+ printk(KERN_DEBUG "%s(card %d):",
+ __func__, hc->id + 1);
+ temp = 0;
+ while (temp < (*sp)->len)
+ printk(" %02x", (*sp)->data[temp++]);
+ printk("\n");
+ }
+ if (dch)
+ recv_Dchannel(dch);
+ else
+ recv_Bchannel(bch);
+ *sp = skb;
+ again++;
+ goto next_frame;
+ }
+ /* there is an incomplete frame */
+ } else {
+ /* transparent */
+ if (Zsize > skb_tailroom(*sp))
+ Zsize = skb_tailroom(*sp);
+ hc->read_fifo(hc, skb_put(*sp, Zsize), Zsize);
+ if (((*sp)->len) < MISDN_COPY_SIZE) {
+ skb = *sp;
+ *sp = mI_alloc_skb(skb->len, GFP_ATOMIC);
+ if (*sp) {
+ memcpy(skb_put(*sp, skb->len),
+ skb->data, skb->len);
+ skb_trim(skb, 0);
+ } else {
+ printk(KERN_DEBUG "%s: No mem\n", __func__);
+ *sp = skb;
+ skb = NULL;
+ }
+ } else {
+ skb = NULL;
+ }
+ if (debug & DEBUG_HFCMULTI_FIFO)
+ printk(KERN_DEBUG
+ "%s(card %d): fifo(%d) reading %d bytes "
+ "(z1=%04x, z2=%04x) TRANS\n",
+ __func__, hc->id + 1, ch, Zsize, z1, z2);
+ /* only bch is transparent */
+ recv_Bchannel(bch);
+ *sp = skb;
+ }
+}
+
+
+/*
+ * Interrupt handler
+ */
+static void
+signal_state_up(struct dchannel *dch, int info, char *msg)
+{
+ struct sk_buff *skb;
+ int id, data = info;
+
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG "%s: %s\n", __func__, msg);
+
+ id = TEI_SAPI | (GROUP_TEI << 8); /* manager address */
+
+ skb = _alloc_mISDN_skb(MPH_INFORMATION_IND, id, sizeof(data), &data,
+ GFP_ATOMIC);
+ if (!skb)
+ return;
+ recv_Dchannel_skb(dch, skb);
+}
+
+static inline void
+handle_timer_irq(struct hfc_multi *hc)
+{
+ int ch, temp;
+ struct dchannel *dch;
+ u_long flags;
+
+ /* process queued resync jobs */
+ if (hc->e1_resync) {
+ /* lock, so e1_resync gets not changed */
+ spin_lock_irqsave(&HFClock, flags);
+ if (hc->e1_resync & 1) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "Enable SYNC_I\n");
+ HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC);
+ /* disable JATT, if RX_SYNC is set */
+ if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip))
+ HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX);
+ }
+ if (hc->e1_resync & 2) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG "Enable jatt PLL\n");
+ HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS);
+ }
+ if (hc->e1_resync & 4) {
+ if (debug & DEBUG_HFCMULTI_PLXSD)
+ printk(KERN_DEBUG
+ "Enable QUARTZ for HFC-E1\n");
+ /* set jatt to quartz */
+ HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC
+ | V_JATT_OFF);
+ /* switch to JATT, in case it is not already */
+ HFC_outb(hc, R_SYNC_OUT, 0);
+ }
+ hc->e1_resync = 0;
+ spin_unlock_irqrestore(&HFClock, flags);
+ }
+
+ if (hc->type != 1 || hc->e1_state == 1)
+ for (ch = 0; ch <= 31; ch++) {
+ if (hc->created[hc->chan[ch].port]) {
+ hfcmulti_tx(hc, ch);
+ /* fifo is started when switching to rx-fifo */
+ hfcmulti_rx(hc, ch);
+ if (hc->chan[ch].dch &&
+ hc->chan[ch].nt_timer > -1) {
+ dch = hc->chan[ch].dch;
+ if (!(--hc->chan[ch].nt_timer)) {
+ schedule_event(dch,
+ FLG_PHCHANGE);
+ if (debug &
+ DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: nt_timer at "
+ "state %x\n",
+ __func__,
+ dch->state);
+ }
+ }
+ }
+ }
+ if (hc->type == 1 && hc->created[0]) {
+ dch = hc->chan[hc->dslot].dch;
+ if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dslot].cfg)) {
+ /* LOS */
+ temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_SIG_LOS;
+ if (!temp && hc->chan[hc->dslot].los)
+ signal_state_up(dch, L1_SIGNAL_LOS_ON,
+ "LOS detected");
+ if (temp && !hc->chan[hc->dslot].los)
+ signal_state_up(dch, L1_SIGNAL_LOS_OFF,
+ "LOS gone");
+ hc->chan[hc->dslot].los = temp;
+ }
+ if (test_bit(HFC_CFG_REPORT_AIS, &hc->chan[hc->dslot].cfg)) {
+ /* AIS */
+ temp = HFC_inb_nodebug(hc, R_SYNC_STA) & V_AIS;
+ if (!temp && hc->chan[hc->dslot].ais)
+ signal_state_up(dch, L1_SIGNAL_AIS_ON,
+ "AIS detected");
+ if (temp && !hc->chan[hc->dslot].ais)
+ signal_state_up(dch, L1_SIGNAL_AIS_OFF,
+ "AIS gone");
+ hc->chan[hc->dslot].ais = temp;
+ }
+ if (test_bit(HFC_CFG_REPORT_SLIP, &hc->chan[hc->dslot].cfg)) {
+ /* SLIP */
+ temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_RX;
+ if (!temp && hc->chan[hc->dslot].slip_rx)
+ signal_state_up(dch, L1_SIGNAL_SLIP_RX,
+ " bit SLIP detected RX");
+ hc->chan[hc->dslot].slip_rx = temp;
+ temp = HFC_inb_nodebug(hc, R_SLIP) & V_FOSLIP_TX;
+ if (!temp && hc->chan[hc->dslot].slip_tx)
+ signal_state_up(dch, L1_SIGNAL_SLIP_TX,
+ " bit SLIP detected TX");
+ hc->chan[hc->dslot].slip_tx = temp;
+ }
+ if (test_bit(HFC_CFG_REPORT_RDI, &hc->chan[hc->dslot].cfg)) {
+ /* RDI */
+ temp = HFC_inb_nodebug(hc, R_RX_SL0_0) & V_A;
+ if (!temp && hc->chan[hc->dslot].rdi)
+ signal_state_up(dch, L1_SIGNAL_RDI_ON,
+ "RDI detected");
+ if (temp && !hc->chan[hc->dslot].rdi)
+ signal_state_up(dch, L1_SIGNAL_RDI_OFF,
+ "RDI gone");
+ hc->chan[hc->dslot].rdi = temp;
+ }
+ temp = HFC_inb_nodebug(hc, R_JATT_DIR);
+ switch (hc->chan[hc->dslot].sync) {
+ case 0:
+ if ((temp & 0x60) == 0x60) {
+ if (debug & DEBUG_HFCMULTI_SYNC)
+ printk(KERN_DEBUG
+ "%s: (id=%d) E1 now "
+ "in clock sync\n",
+ __func__, hc->id);
+ HFC_outb(hc, R_RX_OFF,
+ hc->chan[hc->dslot].jitter | V_RX_INIT);
+ HFC_outb(hc, R_TX_OFF,
+ hc->chan[hc->dslot].jitter | V_RX_INIT);
+ hc->chan[hc->dslot].sync = 1;
+ goto check_framesync;
+ }
+ break;
+ case 1:
+ if ((temp & 0x60) != 0x60) {
+ if (debug & DEBUG_HFCMULTI_SYNC)
+ printk(KERN_DEBUG
+ "%s: (id=%d) E1 "
+ "lost clock sync\n",
+ __func__, hc->id);
+ hc->chan[hc->dslot].sync = 0;
+ break;
+ }
+check_framesync:
+ temp = HFC_inb_nodebug(hc, R_SYNC_STA);
+ if (temp == 0x27) {
+ if (debug & DEBUG_HFCMULTI_SYNC)
+ printk(KERN_DEBUG
+ "%s: (id=%d) E1 "
+ "now in frame sync\n",
+ __func__, hc->id);
+ hc->chan[hc->dslot].sync = 2;
+ }
+ break;
+ case 2:
+ if ((temp & 0x60) != 0x60) {
+ if (debug & DEBUG_HFCMULTI_SYNC)
+ printk(KERN_DEBUG
+ "%s: (id=%d) E1 lost "
+ "clock & frame sync\n",
+ __func__, hc->id);
+ hc->chan[hc->dslot].sync = 0;
+ break;
+ }
+ temp = HFC_inb_nodebug(hc, R_SYNC_STA);
+ if (temp != 0x27) {
+ if (debug & DEBUG_HFCMULTI_SYNC)
+ printk(KERN_DEBUG
+ "%s: (id=%d) E1 "
+ "lost frame sync\n",
+ __func__, hc->id);
+ hc->chan[hc->dslot].sync = 1;
+ }
+ break;
+ }
+ }
+
+ if (test_bit(HFC_CHIP_WATCHDOG, &hc->chip))
+ hfcmulti_watchdog(hc);
+
+ if (hc->leds)
+ hfcmulti_leds(hc);
+}
+
+static void
+ph_state_irq(struct hfc_multi *hc, u_char r_irq_statech)
+{
+ struct dchannel *dch;
+ int ch;
+ int active;
+ u_char st_status, temp;
+
+ /* state machine */
+ for (ch = 0; ch <= 31; ch++) {
+ if (hc->chan[ch].dch) {
+ dch = hc->chan[ch].dch;
+ if (r_irq_statech & 1) {
+ HFC_outb_nodebug(hc, R_ST_SEL,
+ hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ /* undocumented: status changes during read */
+ st_status = HFC_inb_nodebug(hc, A_ST_RD_STATE);
+ while (st_status != (temp =
+ HFC_inb_nodebug(hc, A_ST_RD_STATE))) {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG "%s: reread "
+ "STATE because %d!=%d\n",
+ __func__, temp,
+ st_status);
+ st_status = temp; /* repeat */
+ }
+
+ /* Speech Design TE-sync indication */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip) &&
+ dch->dev.D.protocol == ISDN_P_TE_S0) {
+ if (st_status & V_FR_SYNC_ST)
+ hc->syncronized |=
+ (1 << hc->chan[ch].port);
+ else
+ hc->syncronized &=
+ ~(1 << hc->chan[ch].port);
+ }
+ dch->state = st_status & 0x0f;
+ if (dch->dev.D.protocol == ISDN_P_NT_S0)
+ active = 3;
+ else
+ active = 7;
+ if (dch->state == active) {
+ HFC_outb_nodebug(hc, R_FIFO,
+ (ch << 1) | 1);
+ HFC_wait_nodebug(hc);
+ HFC_outb_nodebug(hc,
+ R_INC_RES_FIFO, V_RES_F);
+ HFC_wait_nodebug(hc);
+ dch->tx_idx = 0;
+ }
+ schedule_event(dch, FLG_PHCHANGE);
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: S/T newstate %x port %d\n",
+ __func__, dch->state,
+ hc->chan[ch].port);
+ }
+ r_irq_statech >>= 1;
+ }
+ }
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
+ plxsd_checksync(hc, 0);
+}
+
+static void
+fifo_irq(struct hfc_multi *hc, int block)
+{
+ int ch, j;
+ struct dchannel *dch;
+ struct bchannel *bch;
+ u_char r_irq_fifo_bl;
+
+ r_irq_fifo_bl = HFC_inb_nodebug(hc, R_IRQ_FIFO_BL0 + block);
+ j = 0;
+ while (j < 8) {
+ ch = (block << 2) + (j >> 1);
+ dch = hc->chan[ch].dch;
+ bch = hc->chan[ch].bch;
+ if (((!dch) && (!bch)) || (!hc->created[hc->chan[ch].port])) {
+ j += 2;
+ continue;
+ }
+ if (dch && (r_irq_fifo_bl & (1 << j)) &&
+ test_bit(FLG_ACTIVE, &dch->Flags)) {
+ hfcmulti_tx(hc, ch);
+ /* start fifo */
+ HFC_outb_nodebug(hc, R_FIFO, 0);
+ HFC_wait_nodebug(hc);
+ }
+ if (bch && (r_irq_fifo_bl & (1 << j)) &&
+ test_bit(FLG_ACTIVE, &bch->Flags)) {
+ hfcmulti_tx(hc, ch);
+ /* start fifo */
+ HFC_outb_nodebug(hc, R_FIFO, 0);
+ HFC_wait_nodebug(hc);
+ }
+ j++;
+ if (dch && (r_irq_fifo_bl & (1 << j)) &&
+ test_bit(FLG_ACTIVE, &dch->Flags)) {
+ hfcmulti_rx(hc, ch);
+ }
+ if (bch && (r_irq_fifo_bl & (1 << j)) &&
+ test_bit(FLG_ACTIVE, &bch->Flags)) {
+ hfcmulti_rx(hc, ch);
+ }
+ j++;
+ }
+}
+
+#ifdef IRQ_DEBUG
+int irqsem;
+#endif
+static irqreturn_t
+hfcmulti_interrupt(int intno, void *dev_id)
+{
+#ifdef IRQCOUNT_DEBUG
+ static int iq1 = 0, iq2 = 0, iq3 = 0, iq4 = 0,
+ iq5 = 0, iq6 = 0, iqcnt = 0;
+#endif
+ static int count;
+ struct hfc_multi *hc = dev_id;
+ struct dchannel *dch;
+ u_char r_irq_statech, status, r_irq_misc, r_irq_oview;
+ int i;
+ u_short *plx_acc, wval;
+ u_char e1_syncsta, temp;
+ u_long flags;
+
+ if (!hc) {
+ printk(KERN_ERR "HFC-multi: Spurious interrupt!\n");
+ return IRQ_NONE;
+ }
+
+ spin_lock(&hc->lock);
+
+#ifdef IRQ_DEBUG
+ if (irqsem)
+ printk(KERN_ERR "irq for card %d during irq from "
+ "card %d, this is no bug.\n", hc->id + 1, irqsem);
+ irqsem = hc->id + 1;
+#endif
+
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ spin_lock_irqsave(&plx_lock, flags);
+ plx_acc = (u_short *)(hc->plx_membase + PLX_INTCSR);
+ wval = readw(plx_acc);
+ spin_unlock_irqrestore(&plx_lock, flags);
+ if (!(wval & PLX_INTCSR_LINTI1_STATUS))
+ goto irq_notforus;
+ }
+
+ status = HFC_inb_nodebug(hc, R_STATUS);
+ r_irq_statech = HFC_inb_nodebug(hc, R_IRQ_STATECH);
+#ifdef IRQCOUNT_DEBUG
+ if (r_irq_statech)
+ iq1++;
+ if (status & V_DTMF_STA)
+ iq2++;
+ if (status & V_LOST_STA)
+ iq3++;
+ if (status & V_EXT_IRQSTA)
+ iq4++;
+ if (status & V_MISC_IRQSTA)
+ iq5++;
+ if (status & V_FR_IRQSTA)
+ iq6++;
+ if (iqcnt++ > 5000) {
+ printk(KERN_ERR "iq1:%x iq2:%x iq3:%x iq4:%x iq5:%x iq6:%x\n",
+ iq1, iq2, iq3, iq4, iq5, iq6);
+ iqcnt = 0;
+ }
+#endif
+ if (!r_irq_statech &&
+ !(status & (V_DTMF_STA | V_LOST_STA | V_EXT_IRQSTA |
+ V_MISC_IRQSTA | V_FR_IRQSTA))) {
+ /* irq is not for us */
+ goto irq_notforus;
+ }
+ hc->irqcnt++;
+ if (r_irq_statech) {
+ if (hc->type != 1)
+ ph_state_irq(hc, r_irq_statech);
+ }
+ if (status & V_EXT_IRQSTA)
+ ; /* external IRQ */
+ if (status & V_LOST_STA) {
+ /* LOST IRQ */
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_LOST); /* clear irq! */
+ }
+ if (status & V_MISC_IRQSTA) {
+ /* misc IRQ */
+ r_irq_misc = HFC_inb_nodebug(hc, R_IRQ_MISC);
+ if (r_irq_misc & V_STA_IRQ) {
+ if (hc->type == 1) {
+ /* state machine */
+ dch = hc->chan[hc->dslot].dch;
+ e1_syncsta = HFC_inb_nodebug(hc, R_SYNC_STA);
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)
+ && hc->e1_getclock) {
+ if (e1_syncsta & V_FR_SYNC_E1)
+ hc->syncronized = 1;
+ else
+ hc->syncronized = 0;
+ }
+ /* undocumented: status changes during read */
+ dch->state = HFC_inb_nodebug(hc, R_E1_RD_STA);
+ while (dch->state != (temp =
+ HFC_inb_nodebug(hc, R_E1_RD_STA))) {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG "%s: reread "
+ "STATE because %d!=%d\n",
+ __func__, temp,
+ dch->state);
+ dch->state = temp; /* repeat */
+ }
+ dch->state = HFC_inb_nodebug(hc, R_E1_RD_STA)
+ & 0x7;
+ schedule_event(dch, FLG_PHCHANGE);
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: E1 (id=%d) newstate %x\n",
+ __func__, hc->id, dch->state);
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip))
+ plxsd_checksync(hc, 0);
+ }
+ }
+ if (r_irq_misc & V_TI_IRQ)
+ handle_timer_irq(hc);
+
+ if (r_irq_misc & V_DTMF_IRQ) {
+ /* -> DTMF IRQ */
+ hfcmulti_dtmf(hc);
+ }
+ /* TODO: REPLACE !!!! 125 us Interrupts are not acceptable */
+ if (r_irq_misc & V_IRQ_PROC) {
+ /* IRQ every 125us */
+ count++;
+ /* generate 1kHz signal */
+ if (count == 8) {
+ if (hfc_interrupt)
+ hfc_interrupt();
+ count = 0;
+ }
+ }
+
+ }
+ if (status & V_FR_IRQSTA) {
+ /* FIFO IRQ */
+ r_irq_oview = HFC_inb_nodebug(hc, R_IRQ_OVIEW);
+ for (i = 0; i < 8; i++) {
+ if (r_irq_oview & (1 << i))
+ fifo_irq(hc, i);
+ }
+ }
+
+#ifdef IRQ_DEBUG
+ irqsem = 0;
+#endif
+ spin_unlock(&hc->lock);
+ return IRQ_HANDLED;
+
+irq_notforus:
+#ifdef IRQ_DEBUG
+ irqsem = 0;
+#endif
+ spin_unlock(&hc->lock);
+ return IRQ_NONE;
+}
+
+
+/*
+ * timer callback for D-chan busy resolution. Currently no function
+ */
+
+static void
+hfcmulti_dbusy_timer(struct hfc_multi *hc)
+{
+}
+
+
+/*
+ * activate/deactivate hardware for selected channels and mode
+ *
+ * configure B-channel with the given protocol
+ * ch eqals to the HFC-channel (0-31)
+ * ch is the number of channel (0-4,4-7,8-11,12-15,16-19,20-23,24-27,28-31
+ * for S/T, 1-31 for E1)
+ * the hdlc interrupts will be set/unset
+ */
+static int
+mode_hfcmulti(struct hfc_multi *hc, int ch, int protocol, int slot_tx,
+ int bank_tx, int slot_rx, int bank_rx)
+{
+ int flow_tx = 0, flow_rx = 0, routing = 0;
+ int oslot_tx, oslot_rx;
+ int conf;
+
+ if (ch < 0 || ch > 31)
+ return EINVAL;
+ oslot_tx = hc->chan[ch].slot_tx;
+ oslot_rx = hc->chan[ch].slot_rx;
+ conf = hc->chan[ch].conf;
+
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG
+ "%s: card %d channel %d protocol %x slot old=%d new=%d "
+ "bank new=%d (TX) slot old=%d new=%d bank new=%d (RX)\n",
+ __func__, hc->id, ch, protocol, oslot_tx, slot_tx,
+ bank_tx, oslot_rx, slot_rx, bank_rx);
+
+ if (oslot_tx >= 0 && slot_tx != oslot_tx) {
+ /* remove from slot */
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG "%s: remove from slot %d (TX)\n",
+ __func__, oslot_tx);
+ if (hc->slot_owner[oslot_tx<<1] == ch) {
+ HFC_outb(hc, R_SLOT, oslot_tx << 1);
+ HFC_outb(hc, A_SL_CFG, 0);
+ HFC_outb(hc, A_CONF, 0);
+ hc->slot_owner[oslot_tx<<1] = -1;
+ } else {
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG
+ "%s: we are not owner of this tx slot "
+ "anymore, channel %d is.\n",
+ __func__, hc->slot_owner[oslot_tx<<1]);
+ }
+ }
+
+ if (oslot_rx >= 0 && slot_rx != oslot_rx) {
+ /* remove from slot */
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG
+ "%s: remove from slot %d (RX)\n",
+ __func__, oslot_rx);
+ if (hc->slot_owner[(oslot_rx << 1) | 1] == ch) {
+ HFC_outb(hc, R_SLOT, (oslot_rx << 1) | V_SL_DIR);
+ HFC_outb(hc, A_SL_CFG, 0);
+ hc->slot_owner[(oslot_rx << 1) | 1] = -1;
+ } else {
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG
+ "%s: we are not owner of this rx slot "
+ "anymore, channel %d is.\n",
+ __func__,
+ hc->slot_owner[(oslot_rx << 1) | 1]);
+ }
+ }
+
+ if (slot_tx < 0) {
+ flow_tx = 0x80; /* FIFO->ST */
+ /* disable pcm slot */
+ hc->chan[ch].slot_tx = -1;
+ hc->chan[ch].bank_tx = 0;
+ } else {
+ /* set pcm slot */
+ if (hc->chan[ch].txpending)
+ flow_tx = 0x80; /* FIFO->ST */
+ else
+ flow_tx = 0xc0; /* PCM->ST */
+ /* put on slot */
+ routing = bank_tx ? 0xc0 : 0x80;
+ if (conf >= 0 || bank_tx > 1)
+ routing = 0x40; /* loop */
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG "%s: put channel %d to slot %d bank"
+ " %d flow %02x routing %02x conf %d (TX)\n",
+ __func__, ch, slot_tx, bank_tx,
+ flow_tx, routing, conf);
+ HFC_outb(hc, R_SLOT, slot_tx << 1);
+ HFC_outb(hc, A_SL_CFG, (ch<<1) | routing);
+ HFC_outb(hc, A_CONF, (conf < 0) ? 0 : (conf | V_CONF_SL));
+ hc->slot_owner[slot_tx << 1] = ch;
+ hc->chan[ch].slot_tx = slot_tx;
+ hc->chan[ch].bank_tx = bank_tx;
+ }
+ if (slot_rx < 0) {
+ /* disable pcm slot */
+ flow_rx = 0x80; /* ST->FIFO */
+ hc->chan[ch].slot_rx = -1;
+ hc->chan[ch].bank_rx = 0;
+ } else {
+ /* set pcm slot */
+ if (hc->chan[ch].txpending)
+ flow_rx = 0x80; /* ST->FIFO */
+ else
+ flow_rx = 0xc0; /* ST->(FIFO,PCM) */
+ /* put on slot */
+ routing = bank_rx?0x80:0xc0; /* reversed */
+ if (conf >= 0 || bank_rx > 1)
+ routing = 0x40; /* loop */
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_DEBUG "%s: put channel %d to slot %d bank"
+ " %d flow %02x routing %02x conf %d (RX)\n",
+ __func__, ch, slot_rx, bank_rx,
+ flow_rx, routing, conf);
+ HFC_outb(hc, R_SLOT, (slot_rx<<1) | V_SL_DIR);
+ HFC_outb(hc, A_SL_CFG, (ch<<1) | V_CH_DIR | routing);
+ hc->slot_owner[(slot_rx<<1)|1] = ch;
+ hc->chan[ch].slot_rx = slot_rx;
+ hc->chan[ch].bank_rx = bank_rx;
+ }
+
+ switch (protocol) {
+ case (ISDN_P_NONE):
+ /* disable TX fifo */
+ HFC_outb(hc, R_FIFO, ch << 1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 | V_IFF);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ /* disable RX fifo */
+ HFC_outb(hc, R_FIFO, (ch<<1)|1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ if (hc->chan[ch].bch && hc->type != 1) {
+ hc->hw.a_st_ctrl0[hc->chan[ch].port] &=
+ ((ch & 0x3) == 0)? ~V_B1_EN: ~V_B2_EN;
+ HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_CTRL0,
+ hc->hw.a_st_ctrl0[hc->chan[ch].port]);
+ }
+ if (hc->chan[ch].bch) {
+ test_and_clear_bit(FLG_HDLC, &hc->chan[ch].bch->Flags);
+ test_and_clear_bit(FLG_TRANSPARENT,
+ &hc->chan[ch].bch->Flags);
+ }
+ break;
+ case (ISDN_P_B_RAW): /* B-channel */
+
+ if (test_bit(HFC_CHIP_B410P, &hc->chip) &&
+ (hc->chan[ch].slot_rx < 0) &&
+ (hc->chan[ch].slot_tx < 0)) {
+
+ printk(KERN_DEBUG
+ "Setting B-channel %d to echo cancelable "
+ "state on PCM slot %d\n", ch,
+ ((ch / 4) * 8) + ((ch % 4) * 4) + 1);
+ printk(KERN_DEBUG
+ "Enabling pass through for channel\n");
+ vpm_out(hc, ch, ((ch / 4) * 8) +
+ ((ch % 4) * 4) + 1, 0x01);
+ /* rx path */
+ /* S/T -> PCM */
+ HFC_outb(hc, R_FIFO, (ch << 1));
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF);
+ HFC_outb(hc, R_SLOT, (((ch / 4) * 8) +
+ ((ch % 4) * 4) + 1) << 1);
+ HFC_outb(hc, A_SL_CFG, 0x80 | (ch << 1));
+
+ /* PCM -> FIFO */
+ HFC_outb(hc, R_FIFO, 0x20 | (ch << 1) | 1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) +
+ ((ch % 4) * 4) + 1) << 1) | 1);
+ HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1) | 1);
+
+ /* tx path */
+ /* PCM -> S/T */
+ HFC_outb(hc, R_FIFO, (ch << 1) | 1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, 0xc0 | V_HDLC_TRP | V_IFF);
+ HFC_outb(hc, R_SLOT, ((((ch / 4) * 8) +
+ ((ch % 4) * 4)) << 1) | 1);
+ HFC_outb(hc, A_SL_CFG, 0x80 | 0x40 | (ch << 1) | 1);
+
+ /* FIFO -> PCM */
+ HFC_outb(hc, R_FIFO, 0x20 | (ch << 1));
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, 0x20 | V_HDLC_TRP | V_IFF);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ /* tx silence */
+ HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, silence);
+ HFC_outb(hc, R_SLOT, (((ch / 4) * 8) +
+ ((ch % 4) * 4)) << 1);
+ HFC_outb(hc, A_SL_CFG, 0x80 | 0x20 | (ch << 1));
+ } else {
+ /* enable TX fifo */
+ HFC_outb(hc, R_FIFO, ch << 1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, flow_tx | 0x00 |
+ V_HDLC_TRP | V_IFF);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ /* tx silence */
+ HFC_outb_nodebug(hc, A_FIFO_DATA0_NOINC, silence);
+ /* enable RX fifo */
+ HFC_outb(hc, R_FIFO, (ch<<1)|1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, flow_rx | 0x00 | V_HDLC_TRP);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ HFC_outb(hc, A_IRQ_MSK, 0);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ }
+ if (hc->type != 1) {
+ hc->hw.a_st_ctrl0[hc->chan[ch].port] |=
+ ((ch & 0x3) == 0) ? V_B1_EN : V_B2_EN;
+ HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_CTRL0,
+ hc->hw.a_st_ctrl0[hc->chan[ch].port]);
+ }
+ if (hc->chan[ch].bch)
+ test_and_set_bit(FLG_TRANSPARENT,
+ &hc->chan[ch].bch->Flags);
+ break;
+ case (ISDN_P_B_HDLC): /* B-channel */
+ case (ISDN_P_TE_S0): /* D-channel */
+ case (ISDN_P_NT_S0):
+ case (ISDN_P_TE_E1):
+ case (ISDN_P_NT_E1):
+ /* enable TX fifo */
+ HFC_outb(hc, R_FIFO, ch<<1);
+ HFC_wait(hc);
+ if (hc->type == 1 || hc->chan[ch].bch) {
+ /* E1 or B-channel */
+ HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04);
+ HFC_outb(hc, A_SUBCH_CFG, 0);
+ } else {
+ /* D-Channel without HDLC fill flags */
+ HFC_outb(hc, A_CON_HDLC, flow_tx | 0x04 | V_IFF);
+ HFC_outb(hc, A_SUBCH_CFG, 2);
+ }
+ HFC_outb(hc, A_IRQ_MSK, V_IRQ);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ /* enable RX fifo */
+ HFC_outb(hc, R_FIFO, (ch<<1)|1);
+ HFC_wait(hc);
+ HFC_outb(hc, A_CON_HDLC, flow_rx | 0x04);
+ if (hc->type == 1 || hc->chan[ch].bch)
+ HFC_outb(hc, A_SUBCH_CFG, 0); /* full 8 bits */
+ else
+ HFC_outb(hc, A_SUBCH_CFG, 2); /* 2 bits dchannel */
+ HFC_outb(hc, A_IRQ_MSK, V_IRQ);
+ HFC_outb(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait(hc);
+ if (hc->chan[ch].bch) {
+ test_and_set_bit(FLG_HDLC, &hc->chan[ch].bch->Flags);
+ if (hc->type != 1) {
+ hc->hw.a_st_ctrl0[hc->chan[ch].port] |=
+ ((ch&0x3) == 0) ? V_B1_EN : V_B2_EN;
+ HFC_outb(hc, R_ST_SEL, hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_CTRL0,
+ hc->hw.a_st_ctrl0[hc->chan[ch].port]);
+ }
+ }
+ break;
+ default:
+ printk(KERN_DEBUG "%s: protocol not known %x\n",
+ __func__, protocol);
+ hc->chan[ch].protocol = ISDN_P_NONE;
+ return -ENOPROTOOPT;
+ }
+ hc->chan[ch].protocol = protocol;
+ return 0;
+}
+
+
+/*
+ * connect/disconnect PCM
+ */
+
+static void
+hfcmulti_pcm(struct hfc_multi *hc, int ch, int slot_tx, int bank_tx,
+ int slot_rx, int bank_rx)
+{
+ if (slot_rx < 0 || slot_rx < 0 || bank_tx < 0 || bank_rx < 0) {
+ /* disable PCM */
+ mode_hfcmulti(hc, ch, hc->chan[ch].protocol, -1, 0, -1, 0);
+ return;
+ }
+
+ /* enable pcm */
+ mode_hfcmulti(hc, ch, hc->chan[ch].protocol, slot_tx, bank_tx,
+ slot_rx, bank_rx);
+}
+
+/*
+ * set/disable conference
+ */
+
+static void
+hfcmulti_conf(struct hfc_multi *hc, int ch, int num)
+{
+ if (num >= 0 && num <= 7)
+ hc->chan[ch].conf = num;
+ else
+ hc->chan[ch].conf = -1;
+ mode_hfcmulti(hc, ch, hc->chan[ch].protocol, hc->chan[ch].slot_tx,
+ hc->chan[ch].bank_tx, hc->chan[ch].slot_rx,
+ hc->chan[ch].bank_rx);
+}
+
+
+/*
+ * set/disable sample loop
+ */
+
+/* NOTE: this function is experimental and therefore disabled */
+
+/*
+ * Layer 1 callback function
+ */
+static int
+hfcm_l1callback(struct dchannel *dch, u_int cmd)
+{
+ struct hfc_multi *hc = dch->hw;
+ u_long flags;
+
+ switch (cmd) {
+ case INFO3_P8:
+ case INFO3_P10:
+ break;
+ case HW_RESET_REQ:
+ /* start activation */
+ spin_lock_irqsave(&hc->lock, flags);
+ if (hc->type == 1) {
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: HW_RESET_REQ no BRI\n",
+ __func__);
+ } else {
+ HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 3); /* F3 */
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, A_ST_WR_STATE, 3);
+ HFC_outb(hc, A_ST_WR_STATE, 3 | (V_ST_ACT*3));
+ /* activate */
+ }
+ spin_unlock_irqrestore(&hc->lock, flags);
+ l1_event(dch->l1, HW_POWERUP_IND);
+ break;
+ case HW_DEACT_REQ:
+ /* start deactivation */
+ spin_lock_irqsave(&hc->lock, flags);
+ if (hc->type == 1) {
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: HW_DEACT_REQ no BRI\n",
+ __func__);
+ } else {
+ HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT*2);
+ /* deactivate */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ hc->syncronized &=
+ ~(1 << hc->chan[dch->slot].port);
+ plxsd_checksync(hc, 0);
+ }
+ }
+ skb_queue_purge(&dch->squeue);
+ if (dch->tx_skb) {
+ dev_kfree_skb(dch->tx_skb);
+ dch->tx_skb = NULL;
+ }
+ dch->tx_idx = 0;
+ if (dch->rx_skb) {
+ dev_kfree_skb(dch->rx_skb);
+ dch->rx_skb = NULL;
+ }
+ test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
+ if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags))
+ del_timer(&dch->timer);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ break;
+ case HW_POWERUP_REQ:
+ spin_lock_irqsave(&hc->lock, flags);
+ if (hc->type == 1) {
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: HW_POWERUP_REQ no BRI\n",
+ __func__);
+ } else {
+ HFC_outb(hc, R_ST_SEL, hc->chan[dch->slot].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, 3 | 0x10); /* activate */
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, A_ST_WR_STATE, 3); /* activate */
+ }
+ spin_unlock_irqrestore(&hc->lock, flags);
+ break;
+ case PH_ACTIVATE_IND:
+ test_and_set_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL,
+ GFP_ATOMIC);
+ break;
+ case PH_DEACTIVATE_IND:
+ test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, cmd, MISDN_ID_ANY, 0, NULL,
+ GFP_ATOMIC);
+ break;
+ default:
+ if (dch->debug & DEBUG_HW)
+ printk(KERN_DEBUG "%s: unknown command %x\n",
+ __func__, cmd);
+ return -1;
+ }
+ return 0;
+}
+
+/*
+ * Layer2 -> Layer 1 Transfer
+ */
+
+static int
+handle_dmsg(struct mISDNchannel *ch, struct sk_buff *skb)
+{
+ struct mISDNdevice *dev = container_of(ch, struct mISDNdevice, D);
+ struct dchannel *dch = container_of(dev, struct dchannel, dev);
+ struct hfc_multi *hc = dch->hw;
+ struct mISDNhead *hh = mISDN_HEAD_P(skb);
+ int ret = -EINVAL;
+ unsigned int id;
+ u_long flags;
+
+ switch (hh->prim) {
+ case PH_DATA_REQ:
+ if (skb->len < 1)
+ break;
+ spin_lock_irqsave(&hc->lock, flags);
+ ret = dchannel_senddata(dch, skb);
+ if (ret > 0) { /* direct TX */
+ id = hh->id; /* skb can be freed */
+ hfcmulti_tx(hc, dch->slot);
+ ret = 0;
+ /* start fifo */
+ HFC_outb(hc, R_FIFO, 0);
+ HFC_wait(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ queue_ch_frame(ch, PH_DATA_CNF, id, NULL);
+ } else
+ spin_unlock_irqrestore(&hc->lock, flags);
+ return ret;
+ case PH_ACTIVATE_REQ:
+ if (dch->dev.D.protocol != ISDN_P_TE_S0) {
+ spin_lock_irqsave(&hc->lock, flags);
+ ret = 0;
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: PH_ACTIVATE port %d (0..%d)\n",
+ __func__, hc->chan[dch->slot].port,
+ hc->ports-1);
+ /* start activation */
+ if (hc->type == 1) {
+ ph_state_change(dch);
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: E1 report state %x \n",
+ __func__, dch->state);
+ } else {
+ HFC_outb(hc, R_ST_SEL,
+ hc->chan[dch->slot].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, V_ST_LD_STA | 1);
+ /* G1 */
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, A_ST_WR_STATE, 1);
+ HFC_outb(hc, A_ST_WR_STATE, 1 |
+ (V_ST_ACT*3)); /* activate */
+ dch->state = 1;
+ }
+ spin_unlock_irqrestore(&hc->lock, flags);
+ } else
+ ret = l1_event(dch->l1, hh->prim);
+ break;
+ case PH_DEACTIVATE_REQ:
+ test_and_clear_bit(FLG_L2_ACTIVATED, &dch->Flags);
+ if (dch->dev.D.protocol != ISDN_P_TE_S0) {
+ spin_lock_irqsave(&hc->lock, flags);
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: PH_DEACTIVATE port %d (0..%d)\n",
+ __func__, hc->chan[dch->slot].port,
+ hc->ports-1);
+ /* start deactivation */
+ if (hc->type == 1) {
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: PH_DEACTIVATE no BRI\n",
+ __func__);
+ } else {
+ HFC_outb(hc, R_ST_SEL,
+ hc->chan[dch->slot].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, V_ST_ACT * 2);
+ /* deactivate */
+ dch->state = 1;
+ }
+ skb_queue_purge(&dch->squeue);
+ if (dch->tx_skb) {
+ dev_kfree_skb(dch->tx_skb);
+ dch->tx_skb = NULL;
+ }
+ dch->tx_idx = 0;
+ if (dch->rx_skb) {
+ dev_kfree_skb(dch->rx_skb);
+ dch->rx_skb = NULL;
+ }
+ test_and_clear_bit(FLG_TX_BUSY, &dch->Flags);
+ if (test_and_clear_bit(FLG_BUSY_TIMER, &dch->Flags))
+ del_timer(&dch->timer);
+#ifdef FIXME
+ if (test_and_clear_bit(FLG_L1_BUSY, &dch->Flags))
+ dchannel_sched_event(&hc->dch, D_CLEARBUSY);
+#endif
+ ret = 0;
+ spin_unlock_irqrestore(&hc->lock, flags);
+ } else
+ ret = l1_event(dch->l1, hh->prim);
+ break;
+ }
+ if (!ret)
+ dev_kfree_skb(skb);
+ return ret;
+}
+
+static void
+deactivate_bchannel(struct bchannel *bch)
+{
+ struct hfc_multi *hc = bch->hw;
+ u_long flags;
+
+ spin_lock_irqsave(&hc->lock, flags);
+ if (test_and_clear_bit(FLG_TX_NEXT, &bch->Flags)) {
+ dev_kfree_skb(bch->next_skb);
+ bch->next_skb = NULL;
+ }
+ if (bch->tx_skb) {
+ dev_kfree_skb(bch->tx_skb);
+ bch->tx_skb = NULL;
+ }
+ bch->tx_idx = 0;
+ if (bch->rx_skb) {
+ dev_kfree_skb(bch->rx_skb);
+ bch->rx_skb = NULL;
+ }
+ hc->chan[bch->slot].coeff_count = 0;
+ test_and_clear_bit(FLG_ACTIVE, &bch->Flags);
+ test_and_clear_bit(FLG_TX_BUSY, &bch->Flags);
+ hc->chan[bch->slot].rx_off = 0;
+ hc->chan[bch->slot].conf = -1;
+ mode_hfcmulti(hc, bch->slot, ISDN_P_NONE, -1, 0, -1, 0);
+ spin_unlock_irqrestore(&hc->lock, flags);
+}
+
+static int
+handle_bmsg(struct mISDNchannel *ch, struct sk_buff *skb)
+{
+ struct bchannel *bch = container_of(ch, struct bchannel, ch);
+ struct hfc_multi *hc = bch->hw;
+ int ret = -EINVAL;
+ struct mISDNhead *hh = mISDN_HEAD_P(skb);
+ unsigned int id;
+ u_long flags;
+
+ switch (hh->prim) {
+ case PH_DATA_REQ:
+ if (!skb->len)
+ break;
+ spin_lock_irqsave(&hc->lock, flags);
+ ret = bchannel_senddata(bch, skb);
+ if (ret > 0) { /* direct TX */
+ id = hh->id; /* skb can be freed */
+ hfcmulti_tx(hc, bch->slot);
+ ret = 0;
+ /* start fifo */
+ HFC_outb_nodebug(hc, R_FIFO, 0);
+ HFC_wait_nodebug(hc);
+ if (!test_bit(FLG_TRANSPARENT, &bch->Flags)) {
+ spin_unlock_irqrestore(&hc->lock, flags);
+ queue_ch_frame(ch, PH_DATA_CNF, id, NULL);
+ } else
+ spin_unlock_irqrestore(&hc->lock, flags);
+ } else
+ spin_unlock_irqrestore(&hc->lock, flags);
+ return ret;
+ case PH_ACTIVATE_REQ:
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: PH_ACTIVATE ch %d (0..32)\n",
+ __func__, bch->slot);
+ spin_lock_irqsave(&hc->lock, flags);
+ /* activate B-channel if not already activated */
+ if (!test_and_set_bit(FLG_ACTIVE, &bch->Flags)) {
+ hc->chan[bch->slot].txpending = 0;
+ ret = mode_hfcmulti(hc, bch->slot,
+ ch->protocol,
+ hc->chan[bch->slot].slot_tx,
+ hc->chan[bch->slot].bank_tx,
+ hc->chan[bch->slot].slot_rx,
+ hc->chan[bch->slot].bank_rx);
+ if (!ret) {
+ if (ch->protocol == ISDN_P_B_RAW && !hc->dtmf
+ && test_bit(HFC_CHIP_DTMF, &hc->chip)) {
+ /* start decoder */
+ hc->dtmf = 1;
+ if (debug & DEBUG_HFCMULTI_DTMF)
+ printk(KERN_DEBUG
+ "%s: start dtmf decoder\n",
+ __func__);
+ HFC_outb(hc, R_DTMF, hc->hw.r_dtmf |
+ V_RST_DTMF);
+ }
+ }
+ } else
+ ret = 0;
+ spin_unlock_irqrestore(&hc->lock, flags);
+ if (!ret)
+ _queue_data(ch, PH_ACTIVATE_IND, MISDN_ID_ANY, 0, NULL,
+ GFP_KERNEL);
+ break;
+ case PH_CONTROL_REQ:
+ spin_lock_irqsave(&hc->lock, flags);
+ switch (hh->id) {
+ case HFC_SPL_LOOP_ON: /* set sample loop */
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: HFC_SPL_LOOP_ON (len = %d)\n",
+ __func__, skb->len);
+ ret = 0;
+ break;
+ case HFC_SPL_LOOP_OFF: /* set silence */
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_SPL_LOOP_OFF\n",
+ __func__);
+ ret = 0;
+ break;
+ default:
+ printk(KERN_ERR
+ "%s: unknown PH_CONTROL_REQ info %x\n",
+ __func__, hh->id);
+ ret = -EINVAL;
+ }
+ spin_unlock_irqrestore(&hc->lock, flags);
+ break;
+ case PH_DEACTIVATE_REQ:
+ deactivate_bchannel(bch); /* locked there */
+ _queue_data(ch, PH_DEACTIVATE_IND, MISDN_ID_ANY, 0, NULL,
+ GFP_KERNEL);
+ ret = 0;
+ break;
+ }
+ if (!ret)
+ dev_kfree_skb(skb);
+ return ret;
+}
+
+/*
+ * bchannel control function
+ */
+static int
+channel_bctrl(struct bchannel *bch, struct mISDN_ctrl_req *cq)
+{
+ int ret = 0;
+ struct dsp_features *features =
+ (struct dsp_features *)(*((u_long *)&cq->p1));
+ struct hfc_multi *hc = bch->hw;
+ int slot_tx;
+ int bank_tx;
+ int slot_rx;
+ int bank_rx;
+ int num;
+
+ switch (cq->op) {
+ case MISDN_CTRL_GETOP:
+ cq->op = MISDN_CTRL_HFC_OP | MISDN_CTRL_HW_FEATURES_OP
+ | MISDN_CTRL_RX_OFF;
+ break;
+ case MISDN_CTRL_RX_OFF: /* turn off / on rx stream */
+ hc->chan[bch->slot].rx_off = !!cq->p1;
+ if (!hc->chan[bch->slot].rx_off) {
+ /* reset fifo on rx on */
+ HFC_outb_nodebug(hc, R_FIFO, (bch->slot << 1) | 1);
+ HFC_wait_nodebug(hc);
+ HFC_outb_nodebug(hc, R_INC_RES_FIFO, V_RES_F);
+ HFC_wait_nodebug(hc);
+ }
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: RX_OFF request (nr=%d off=%d)\n",
+ __func__, bch->nr, hc->chan[bch->slot].rx_off);
+ break;
+ case MISDN_CTRL_HW_FEATURES: /* fill features structure */
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HW_FEATURE request\n",
+ __func__);
+ /* create confirm */
+ features->hfc_id = hc->id;
+ if (test_bit(HFC_CHIP_DTMF, &hc->chip))
+ features->hfc_dtmf = 1;
+ features->hfc_loops = 0;
+ if (test_bit(HFC_CHIP_B410P, &hc->chip)) {
+ features->hfc_echocanhw = 1;
+ } else {
+ features->pcm_id = hc->pcm;
+ features->pcm_slots = hc->slots;
+ features->pcm_banks = 2;
+ }
+ break;
+ case MISDN_CTRL_HFC_PCM_CONN: /* connect to pcm timeslot (0..N) */
+ slot_tx = cq->p1 & 0xff;
+ bank_tx = cq->p1 >> 8;
+ slot_rx = cq->p2 & 0xff;
+ bank_rx = cq->p2 >> 8;
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG
+ "%s: HFC_PCM_CONN slot %d bank %d (TX) "
+ "slot %d bank %d (RX)\n",
+ __func__, slot_tx, bank_tx,
+ slot_rx, bank_rx);
+ if (slot_tx < hc->slots && bank_tx <= 2 &&
+ slot_rx < hc->slots && bank_rx <= 2)
+ hfcmulti_pcm(hc, bch->slot,
+ slot_tx, bank_tx, slot_rx, bank_rx);
+ else {
+ printk(KERN_WARNING
+ "%s: HFC_PCM_CONN slot %d bank %d (TX) "
+ "slot %d bank %d (RX) out of range\n",
+ __func__, slot_tx, bank_tx,
+ slot_rx, bank_rx);
+ ret = -EINVAL;
+ }
+ break;
+ case MISDN_CTRL_HFC_PCM_DISC: /* release interface from pcm timeslot */
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_PCM_DISC\n",
+ __func__);
+ hfcmulti_pcm(hc, bch->slot, -1, 0, -1, 0);
+ break;
+ case MISDN_CTRL_HFC_CONF_JOIN: /* join conference (0..7) */
+ num = cq->p1 & 0xff;
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_CONF_JOIN conf %d\n",
+ __func__, num);
+ if (num <= 7)
+ hfcmulti_conf(hc, bch->slot, num);
+ else {
+ printk(KERN_WARNING
+ "%s: HW_CONF_JOIN conf %d out of range\n",
+ __func__, num);
+ ret = -EINVAL;
+ }
+ break;
+ case MISDN_CTRL_HFC_CONF_SPLIT: /* split conference */
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_CONF_SPLIT\n", __func__);
+ hfcmulti_conf(hc, bch->slot, -1);
+ break;
+ case MISDN_CTRL_HFC_ECHOCAN_ON:
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_ECHOCAN_ON\n", __func__);
+ if (test_bit(HFC_CHIP_B410P, &hc->chip))
+ vpm_echocan_on(hc, bch->slot, cq->p1);
+ else
+ ret = -EINVAL;
+ break;
+
+ case MISDN_CTRL_HFC_ECHOCAN_OFF:
+ if (debug & DEBUG_HFCMULTI_MSG)
+ printk(KERN_DEBUG "%s: HFC_ECHOCAN_OFF\n",
+ __func__);
+ if (test_bit(HFC_CHIP_B410P, &hc->chip))
+ vpm_echocan_off(hc, bch->slot);
+ else
+ ret = -EINVAL;
+ break;
+ default:
+ printk(KERN_WARNING "%s: unknown Op %x\n",
+ __func__, cq->op);
+ ret = -EINVAL;
+ break;
+ }
+ return ret;
+}
+
+static int
+hfcm_bctrl(struct mISDNchannel *ch, u_int cmd, void *arg)
+{
+ struct bchannel *bch = container_of(ch, struct bchannel, ch);
+ struct hfc_multi *hc = bch->hw;
+ int err = -EINVAL;
+ u_long flags;
+
+ if (bch->debug & DEBUG_HW)
+ printk(KERN_DEBUG "%s: cmd:%x %p\n",
+ __func__, cmd, arg);
+ switch (cmd) {
+ case CLOSE_CHANNEL:
+ test_and_clear_bit(FLG_OPEN, &bch->Flags);
+ if (test_bit(FLG_ACTIVE, &bch->Flags))
+ deactivate_bchannel(bch); /* locked there */
+ ch->protocol = ISDN_P_NONE;
+ ch->peer = NULL;
+ module_put(THIS_MODULE);
+ err = 0;
+ break;
+ case CONTROL_CHANNEL:
+ spin_lock_irqsave(&hc->lock, flags);
+ err = channel_bctrl(bch, arg);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ break;
+ default:
+ printk(KERN_WARNING "%s: unknown prim(%x)\n",
+ __func__, cmd);
+ }
+ return err;
+}
+
+/*
+ * handle D-channel events
+ *
+ * handle state change event
+ */
+static void
+ph_state_change(struct dchannel *dch)
+{
+ struct hfc_multi *hc = dch->hw;
+ int ch, i;
+
+ if (!dch) {
+ printk(KERN_WARNING "%s: ERROR given dch is NULL\n",
+ __func__);
+ return;
+ }
+ ch = dch->slot;
+
+ if (hc->type == 1) {
+ if (dch->dev.D.protocol == ISDN_P_TE_E1) {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: E1 TE (id=%d) newstate %x\n",
+ __func__, hc->id, dch->state);
+ } else {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: E1 NT (id=%d) newstate %x\n",
+ __func__, hc->id, dch->state);
+ }
+ switch (dch->state) {
+ case (1):
+ if (hc->e1_state != 1) {
+ for (i = 1; i <= 31; i++) {
+ /* reset fifos on e1 activation */
+ HFC_outb_nodebug(hc, R_FIFO, (i << 1) | 1);
+ HFC_wait_nodebug(hc);
+ HFC_outb_nodebug(hc,
+ R_INC_RES_FIFO, V_RES_F);
+ HFC_wait_nodebug(hc);
+ }
+ }
+ test_and_set_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, PH_ACTIVATE_IND,
+ MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
+ break;
+
+ default:
+ if (hc->e1_state != 1)
+ return;
+ test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, PH_DEACTIVATE_IND,
+ MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
+ }
+ hc->e1_state = dch->state;
+ } else {
+ if (dch->dev.D.protocol == ISDN_P_TE_S0) {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG
+ "%s: S/T TE newstate %x\n",
+ __func__, dch->state);
+ switch (dch->state) {
+ case (0):
+ l1_event(dch->l1, HW_RESET_IND);
+ break;
+ case (3):
+ l1_event(dch->l1, HW_DEACT_IND);
+ break;
+ case (5):
+ case (8):
+ l1_event(dch->l1, ANYSIGNAL);
+ break;
+ case (6):
+ l1_event(dch->l1, INFO2);
+ break;
+ case (7):
+ l1_event(dch->l1, INFO4_P8);
+ break;
+ }
+ } else {
+ if (debug & DEBUG_HFCMULTI_STATE)
+ printk(KERN_DEBUG "%s: S/T NT newstate %x\n",
+ __func__, dch->state);
+ switch (dch->state) {
+ case (2):
+ if (hc->chan[ch].nt_timer == 0) {
+ hc->chan[ch].nt_timer = -1;
+ HFC_outb(hc, R_ST_SEL,
+ hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ HFC_outb(hc, A_ST_WR_STATE, 4 |
+ V_ST_LD_STA); /* G4 */
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, A_ST_WR_STATE, 4);
+ dch->state = 4;
+ } else {
+ /* one extra count for the next event */
+ hc->chan[ch].nt_timer =
+ nt_t1_count[poll_timer] + 1;
+ HFC_outb(hc, R_ST_SEL,
+ hc->chan[ch].port);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ /* allow G2 -> G3 transition */
+ HFC_outb(hc, A_ST_WR_STATE, 2 |
+ V_SET_G2_G3);
+ }
+ break;
+ case (1):
+ hc->chan[ch].nt_timer = -1;
+ test_and_clear_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, PH_DEACTIVATE_IND,
+ MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
+ break;
+ case (4):
+ hc->chan[ch].nt_timer = -1;
+ break;
+ case (3):
+ hc->chan[ch].nt_timer = -1;
+ test_and_set_bit(FLG_ACTIVE, &dch->Flags);
+ _queue_data(&dch->dev.D, PH_ACTIVATE_IND,
+ MISDN_ID_ANY, 0, NULL, GFP_ATOMIC);
+ break;
+ }
+ }
+ }
+}
+
+/*
+ * called for card mode init message
+ */
+
+static void
+hfcmulti_initmode(struct dchannel *dch)
+{
+ struct hfc_multi *hc = dch->hw;
+ u_char a_st_wr_state, r_e1_wr_sta;
+ int i, pt;
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: entered\n", __func__);
+
+ if (hc->type == 1) {
+ hc->chan[hc->dslot].slot_tx = -1;
+ hc->chan[hc->dslot].slot_rx = -1;
+ hc->chan[hc->dslot].conf = -1;
+ if (hc->dslot) {
+ mode_hfcmulti(hc, hc->dslot, dch->dev.D.protocol,
+ -1, 0, -1, 0);
+ dch->timer.function = (void *) hfcmulti_dbusy_timer;
+ dch->timer.data = (long) dch;
+ init_timer(&dch->timer);
+ }
+ for (i = 1; i <= 31; i++) {
+ if (i == hc->dslot)
+ continue;
+ hc->chan[i].slot_tx = -1;
+ hc->chan[i].slot_rx = -1;
+ hc->chan[i].conf = -1;
+ mode_hfcmulti(hc, i, ISDN_P_NONE, -1, 0, -1, 0);
+ }
+ /* E1 */
+ if (test_bit(HFC_CFG_REPORT_LOS, &hc->chan[hc->dslot].cfg)) {
+ HFC_outb(hc, R_LOS0, 255); /* 2 ms */
+ HFC_outb(hc, R_LOS1, 255); /* 512 ms */
+ }
+ if (test_bit(HFC_CFG_OPTICAL, &hc->chan[hc->dslot].cfg)) {
+ HFC_outb(hc, R_RX0, 0);
+ hc->hw.r_tx0 = 0 | V_OUT_EN;
+ } else {
+ HFC_outb(hc, R_RX0, 1);
+ hc->hw.r_tx0 = 1 | V_OUT_EN;
+ }
+ hc->hw.r_tx1 = V_ATX | V_NTRI;
+ HFC_outb(hc, R_TX0, hc->hw.r_tx0);
+ HFC_outb(hc, R_TX1, hc->hw.r_tx1);
+ HFC_outb(hc, R_TX_FR0, 0x00);
+ HFC_outb(hc, R_TX_FR1, 0xf8);
+
+ if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dslot].cfg))
+ HFC_outb(hc, R_TX_FR2, V_TX_MF | V_TX_E | V_NEG_E);
+
+ HFC_outb(hc, R_RX_FR0, V_AUTO_RESYNC | V_AUTO_RECO | 0);
+
+ if (test_bit(HFC_CFG_CRC4, &hc->chan[hc->dslot].cfg))
+ HFC_outb(hc, R_RX_FR1, V_RX_MF | V_RX_MF_SYNC);
+
+ if (dch->dev.D.protocol == ISDN_P_NT_E1) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: E1 port is NT-mode\n",
+ __func__);
+ r_e1_wr_sta = 0; /* G0 */
+ hc->e1_getclock = 0;
+ } else {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: E1 port is TE-mode\n",
+ __func__);
+ r_e1_wr_sta = 0; /* F0 */
+ hc->e1_getclock = 1;
+ }
+ if (test_bit(HFC_CHIP_RX_SYNC, &hc->chip))
+ HFC_outb(hc, R_SYNC_OUT, V_SYNC_E1_RX);
+ else
+ HFC_outb(hc, R_SYNC_OUT, 0);
+ if (test_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip))
+ hc->e1_getclock = 1;
+ if (test_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip))
+ hc->e1_getclock = 0;
+ if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
+ /* SLAVE (clock master) */
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: E1 port is clock master "
+ "(clock from PCM)\n", __func__);
+ HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC | V_PCM_SYNC);
+ } else {
+ if (hc->e1_getclock) {
+ /* MASTER (clock slave) */
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: E1 port is clock slave "
+ "(clock to PCM)\n", __func__);
+ HFC_outb(hc, R_SYNC_CTRL, V_SYNC_OFFS);
+ } else {
+ /* MASTER (clock master) */
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: E1 port is "
+ "clock master "
+ "(clock from QUARTZ)\n",
+ __func__);
+ HFC_outb(hc, R_SYNC_CTRL, V_EXT_CLK_SYNC |
+ V_PCM_SYNC | V_JATT_OFF);
+ HFC_outb(hc, R_SYNC_OUT, 0);
+ }
+ }
+ HFC_outb(hc, R_JATT_ATT, 0x9c); /* undoc register */
+ HFC_outb(hc, R_PWM_MD, V_PWM0_MD);
+ HFC_outb(hc, R_PWM0, 0x50);
+ HFC_outb(hc, R_PWM1, 0xff);
+ /* state machine setup */
+ HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta | V_E1_LD_STA);
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, R_E1_WR_STA, r_e1_wr_sta);
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ hc->syncronized = 0;
+ plxsd_checksync(hc, 0);
+ }
+ } else {
+ i = dch->slot;
+ hc->chan[i].slot_tx = -1;
+ hc->chan[i].slot_rx = -1;
+ hc->chan[i].conf = -1;
+ mode_hfcmulti(hc, i, dch->dev.D.protocol, -1, 0, -1, 0);
+ dch->timer.function = (void *)hfcmulti_dbusy_timer;
+ dch->timer.data = (long) dch;
+ init_timer(&dch->timer);
+ hc->chan[i - 2].slot_tx = -1;
+ hc->chan[i - 2].slot_rx = -1;
+ hc->chan[i - 2].conf = -1;
+ mode_hfcmulti(hc, i - 2, ISDN_P_NONE, -1, 0, -1, 0);
+ hc->chan[i - 1].slot_tx = -1;
+ hc->chan[i - 1].slot_rx = -1;
+ hc->chan[i - 1].conf = -1;
+ mode_hfcmulti(hc, i - 1, ISDN_P_NONE, -1, 0, -1, 0);
+ /* ST */
+ pt = hc->chan[i].port;
+ /* select interface */
+ HFC_outb(hc, R_ST_SEL, pt);
+ /* undocumented: delay after R_ST_SEL */
+ udelay(1);
+ if (dch->dev.D.protocol == ISDN_P_NT_S0) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: ST port %d is NT-mode\n",
+ __func__, pt);
+ /* clock delay */
+ HFC_outb(hc, A_ST_CLK_DLY, clockdelay_nt);
+ a_st_wr_state = 1; /* G1 */
+ hc->hw.a_st_ctrl0[pt] = V_ST_MD;
+ } else {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: ST port %d is TE-mode\n",
+ __func__, pt);
+ /* clock delay */
+ HFC_outb(hc, A_ST_CLK_DLY, clockdelay_te);
+ a_st_wr_state = 2; /* F2 */
+ hc->hw.a_st_ctrl0[pt] = 0;
+ }
+ if (!test_bit(HFC_CFG_NONCAP_TX, &hc->chan[i].cfg))
+ hc->hw.a_st_ctrl0[pt] |= V_TX_LI;
+ /* line setup */
+ HFC_outb(hc, A_ST_CTRL0, hc->hw.a_st_ctrl0[pt]);
+ /* disable E-channel */
+ if ((dch->dev.D.protocol == ISDN_P_NT_S0) ||
+ test_bit(HFC_CFG_DIS_ECHANNEL, &hc->chan[i].cfg))
+ HFC_outb(hc, A_ST_CTRL1, V_E_IGNO);
+ else
+ HFC_outb(hc, A_ST_CTRL1, 0);
+ /* enable B-channel receive */
+ HFC_outb(hc, A_ST_CTRL2, V_B1_RX_EN | V_B2_RX_EN);
+ /* state machine setup */
+ HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state | V_ST_LD_STA);
+ udelay(6); /* wait at least 5,21us */
+ HFC_outb(hc, A_ST_WR_STATE, a_st_wr_state);
+ hc->hw.r_sci_msk |= 1 << pt;
+ /* state machine interrupts */
+ HFC_outb(hc, R_SCI_MSK, hc->hw.r_sci_msk);
+ /* unset sync on port */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ hc->syncronized &=
+ ~(1 << hc->chan[dch->slot].port);
+ plxsd_checksync(hc, 0);
+ }
+ }
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk("%s: done\n", __func__);
+}
+
+
+static int
+open_dchannel(struct hfc_multi *hc, struct dchannel *dch,
+ struct channel_req *rq)
+{
+ int err = 0;
+ u_long flags;
+
+ if (debug & DEBUG_HW_OPEN)
+ printk(KERN_DEBUG "%s: dev(%d) open from %p\n", __func__,
+ dch->dev.id, __builtin_return_address(0));
+ if (rq->protocol == ISDN_P_NONE)
+ return -EINVAL;
+ if ((dch->dev.D.protocol != ISDN_P_NONE) &&
+ (dch->dev.D.protocol != rq->protocol)) {
+ if (debug & DEBUG_HFCMULTI_MODE)
+ printk(KERN_WARNING "%s: change protocol %x to %x\n",
+ __func__, dch->dev.D.protocol, rq->protocol);
+ }
+ if ((dch->dev.D.protocol == ISDN_P_TE_S0)
+ && (rq->protocol != ISDN_P_TE_S0))
+ l1_event(dch->l1, CLOSE_CHANNEL);
+ if (dch->dev.D.protocol != rq->protocol) {
+ if (rq->protocol == ISDN_P_TE_S0) {
+ err = create_l1(dch, hfcm_l1callback);
+ if (err)
+ return err;
+ }
+ dch->dev.D.protocol = rq->protocol;
+ spin_lock_irqsave(&hc->lock, flags);
+ hfcmulti_initmode(dch);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ }
+
+ if (((rq->protocol == ISDN_P_NT_S0) && (dch->state == 3)) ||
+ ((rq->protocol == ISDN_P_TE_S0) && (dch->state == 7)) ||
+ ((rq->protocol == ISDN_P_NT_E1) && (dch->state == 1)) ||
+ ((rq->protocol == ISDN_P_TE_E1) && (dch->state == 1))) {
+ _queue_data(&dch->dev.D, PH_ACTIVATE_IND, MISDN_ID_ANY,
+ 0, NULL, GFP_KERNEL);
+ }
+ rq->ch = &dch->dev.D;
+ if (!try_module_get(THIS_MODULE))
+ printk(KERN_WARNING "%s:cannot get module\n", __func__);
+ return 0;
+}
+
+static int
+open_bchannel(struct hfc_multi *hc, struct dchannel *dch,
+ struct channel_req *rq)
+{
+ struct bchannel *bch;
+ int ch;
+
+ if (!test_bit(rq->adr.channel, &dch->dev.channelmap[0]))
+ return -EINVAL;
+ if (rq->protocol == ISDN_P_NONE)
+ return -EINVAL;
+ if (hc->type == 1)
+ ch = rq->adr.channel;
+ else
+ ch = (rq->adr.channel - 1) + (dch->slot - 2);
+ bch = hc->chan[ch].bch;
+ if (!bch) {
+ printk(KERN_ERR "%s:internal error ch %d has no bch\n",
+ __func__, ch);
+ return -EINVAL;
+ }
+ if (test_and_set_bit(FLG_OPEN, &bch->Flags))
+ return -EBUSY; /* b-channel can be only open once */
+ bch->ch.protocol = rq->protocol;
+ hc->chan[ch].rx_off = 0;
+ rq->ch = &bch->ch;
+ if (!try_module_get(THIS_MODULE))
+ printk(KERN_WARNING "%s:cannot get module\n", __func__);
+ return 0;
+}
+
+/*
+ * device control function
+ */
+static int
+channel_dctrl(struct dchannel *dch, struct mISDN_ctrl_req *cq)
+{
+ int ret = 0;
+
+ switch (cq->op) {
+ case MISDN_CTRL_GETOP:
+ cq->op = 0;
+ break;
+ default:
+ printk(KERN_WARNING "%s: unknown Op %x\n",
+ __func__, cq->op);
+ ret = -EINVAL;
+ break;
+ }
+ return ret;
+}
+
+static int
+hfcm_dctrl(struct mISDNchannel *ch, u_int cmd, void *arg)
+{
+ struct mISDNdevice *dev = container_of(ch, struct mISDNdevice, D);
+ struct dchannel *dch = container_of(dev, struct dchannel, dev);
+ struct hfc_multi *hc = dch->hw;
+ struct channel_req *rq;
+ int err = 0;
+ u_long flags;
+
+ if (dch->debug & DEBUG_HW)
+ printk(KERN_DEBUG "%s: cmd:%x %p\n",
+ __func__, cmd, arg);
+ switch (cmd) {
+ case OPEN_CHANNEL:
+ rq = arg;
+ switch (rq->protocol) {
+ case ISDN_P_TE_S0:
+ case ISDN_P_NT_S0:
+ if (hc->type == 1) {
+ err = -EINVAL;
+ break;
+ }
+ err = open_dchannel(hc, dch, rq); /* locked there */
+ break;
+ case ISDN_P_TE_E1:
+ case ISDN_P_NT_E1:
+ if (hc->type != 1) {
+ err = -EINVAL;
+ break;
+ }
+ err = open_dchannel(hc, dch, rq); /* locked there */
+ break;
+ default:
+ spin_lock_irqsave(&hc->lock, flags);
+ err = open_bchannel(hc, dch, rq);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ }
+ break;
+ case CLOSE_CHANNEL:
+ if (debug & DEBUG_HW_OPEN)
+ printk(KERN_DEBUG "%s: dev(%d) close from %p\n",
+ __func__, dch->dev.id,
+ __builtin_return_address(0));
+ module_put(THIS_MODULE);
+ break;
+ case CONTROL_CHANNEL:
+ spin_lock_irqsave(&hc->lock, flags);
+ err = channel_dctrl(dch, arg);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ break;
+ default:
+ if (dch->debug & DEBUG_HW)
+ printk(KERN_DEBUG "%s: unknown command %x\n",
+ __func__, cmd);
+ err = -EINVAL;
+ }
+ return err;
+}
+
+/*
+ * initialize the card
+ */
+
+/*
+ * start timer irq, wait some time and check if we have interrupts.
+ * if not, reset chip and try again.
+ */
+static int
+init_card(struct hfc_multi *hc)
+{
+ int err = -EIO;
+ u_long flags;
+ u_short *plx_acc;
+ u_long plx_flags;
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: entered\n", __func__);
+
+ spin_lock_irqsave(&hc->lock, flags);
+ /* set interrupts but leave global interrupt disabled */
+ hc->hw.r_irq_ctrl = V_FIFO_IRQ;
+ disable_hwirq(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+
+ if (request_irq(hc->pci_dev->irq, hfcmulti_interrupt, IRQF_SHARED,
+ "HFC-multi", hc)) {
+ printk(KERN_WARNING "mISDN: Could not get interrupt %d.\n",
+ hc->pci_dev->irq);
+ return -EIO;
+ }
+ hc->irq = hc->pci_dev->irq;
+
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc = (u_short *)(hc->plx_membase+PLX_INTCSR);
+ writew((PLX_INTCSR_PCIINT_ENABLE | PLX_INTCSR_LINTI1_ENABLE),
+ plx_acc); /* enable PCI & LINT1 irq */
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ }
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: IRQ %d count %d\n",
+ __func__, hc->irq, hc->irqcnt);
+ err = init_chip(hc);
+ if (err)
+ goto error;
+ /*
+ * Finally enable IRQ output
+ * this is only allowed, if an IRQ routine is allready
+ * established for this HFC, so don't do that earlier
+ */
+ spin_lock_irqsave(&hc->lock, flags);
+ enable_hwirq(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ /* printk(KERN_DEBUG "no master irq set!!!\n"); */
+ set_current_state(TASK_UNINTERRUPTIBLE);
+ schedule_timeout((100*HZ)/1000); /* Timeout 100ms */
+ /* turn IRQ off until chip is completely initialized */
+ spin_lock_irqsave(&hc->lock, flags);
+ disable_hwirq(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: IRQ %d count %d\n",
+ __func__, hc->irq, hc->irqcnt);
+ if (hc->irqcnt) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: done\n", __func__);
+
+ return 0;
+ }
+ if (test_bit(HFC_CHIP_PCM_SLAVE, &hc->chip)) {
+ printk(KERN_INFO "ignoring missing interrupts\n");
+ return 0;
+ }
+
+ printk(KERN_ERR "HFC PCI: IRQ(%d) getting no interrupts during init.\n",
+ hc->irq);
+
+ err = -EIO;
+
+error:
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ spin_lock_irqsave(&plx_lock, plx_flags);
+ plx_acc = (u_short *)(hc->plx_membase+PLX_INTCSR);
+ writew(0x00, plx_acc); /*disable IRQs*/
+ spin_unlock_irqrestore(&plx_lock, plx_flags);
+ }
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: free irq %d\n", __func__, hc->irq);
+ if (hc->irq) {
+ free_irq(hc->irq, hc);
+ hc->irq = 0;
+ }
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: done (err=%d)\n", __func__, err);
+ return err;
+}
+
+/*
+ * find pci device and set it up
+ */
+
+static int
+setup_pci(struct hfc_multi *hc, struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct hm_map *m = (struct hm_map *)ent->driver_data;
+
+ printk(KERN_INFO
+ "HFC-multi: card manufacturer: '%s' card name: '%s' clock: %s\n",
+ m->vendor_name, m->card_name, m->clock2 ? "double" : "normal");
+
+ hc->pci_dev = pdev;
+ if (m->clock2)
+ test_and_set_bit(HFC_CHIP_CLOCK2, &hc->chip);
+
+ if (ent->device == 0xB410) {
+ test_and_set_bit(HFC_CHIP_B410P, &hc->chip);
+ test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip);
+ test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
+ hc->slots = 32;
+ }
+
+ if (hc->pci_dev->irq <= 0) {
+ printk(KERN_WARNING "HFC-multi: No IRQ for PCI card found.\n");
+ return -EIO;
+ }
+ if (pci_enable_device(hc->pci_dev)) {
+ printk(KERN_WARNING "HFC-multi: Error enabling PCI card.\n");
+ return -EIO;
+ }
+ hc->leds = m->leds;
+ hc->ledstate = 0xAFFEAFFE;
+ hc->opticalsupport = m->opticalsupport;
+
+ /* set memory access methods */
+ if (m->io_mode) /* use mode from card config */
+ hc->io_mode = m->io_mode;
+ switch (hc->io_mode) {
+ case HFC_IO_MODE_PLXSD:
+ test_and_set_bit(HFC_CHIP_PLXSD, &hc->chip);
+ hc->slots = 128; /* required */
+ /* fall through */
+ case HFC_IO_MODE_PCIMEM:
+ hc->HFC_outb = HFC_outb_pcimem;
+ hc->HFC_inb = HFC_inb_pcimem;
+ hc->HFC_inw = HFC_inw_pcimem;
+ hc->HFC_wait = HFC_wait_pcimem;
+ hc->read_fifo = read_fifo_pcimem;
+ hc->write_fifo = write_fifo_pcimem;
+ break;
+ case HFC_IO_MODE_REGIO:
+ hc->HFC_outb = HFC_outb_regio;
+ hc->HFC_inb = HFC_inb_regio;
+ hc->HFC_inw = HFC_inw_regio;
+ hc->HFC_wait = HFC_wait_regio;
+ hc->read_fifo = read_fifo_regio;
+ hc->write_fifo = write_fifo_regio;
+ break;
+ default:
+ printk(KERN_WARNING "HFC-multi: Invalid IO mode.\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+ hc->HFC_outb_nodebug = hc->HFC_outb;
+ hc->HFC_inb_nodebug = hc->HFC_inb;
+ hc->HFC_inw_nodebug = hc->HFC_inw;
+ hc->HFC_wait_nodebug = hc->HFC_wait;
+#ifdef HFC_REGISTER_DEBUG
+ hc->HFC_outb = HFC_outb_debug;
+ hc->HFC_inb = HFC_inb_debug;
+ hc->HFC_inw = HFC_inw_debug;
+ hc->HFC_wait = HFC_wait_debug;
+#endif
+ hc->pci_iobase = 0;
+ hc->pci_membase = NULL;
+ hc->plx_membase = NULL;
+
+ switch (hc->io_mode) {
+ case HFC_IO_MODE_PLXSD:
+ hc->plx_origmembase = hc->pci_dev->resource[0].start;
+ /* MEMBASE 1 is PLX PCI Bridge */
+
+ if (!hc->plx_origmembase) {
+ printk(KERN_WARNING
+ "HFC-multi: No IO-Memory for PCI PLX bridge found\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ hc->plx_membase = ioremap(hc->plx_origmembase, 0x80);
+ if (!hc->plx_membase) {
+ printk(KERN_WARNING
+ "HFC-multi: failed to remap plx address space. "
+ "(internal error)\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+ printk(KERN_INFO
+ "HFC-multi: plx_membase:%#lx plx_origmembase:%#lx\n",
+ (u_long)hc->plx_membase, hc->plx_origmembase);
+
+ hc->pci_origmembase = hc->pci_dev->resource[2].start;
+ /* MEMBASE 1 is PLX PCI Bridge */
+ if (!hc->pci_origmembase) {
+ printk(KERN_WARNING
+ "HFC-multi: No IO-Memory for PCI card found\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ hc->pci_membase = ioremap(hc->pci_origmembase, 0x400);
+ if (!hc->pci_membase) {
+ printk(KERN_WARNING "HFC-multi: failed to remap io "
+ "address space. (internal error)\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ printk(KERN_INFO
+ "card %d: defined at MEMBASE %#lx (%#lx) IRQ %d HZ %d "
+ "leds-type %d\n",
+ hc->id, (u_long)hc->pci_membase, hc->pci_origmembase,
+ hc->pci_dev->irq, HZ, hc->leds);
+ pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO);
+ break;
+ case HFC_IO_MODE_PCIMEM:
+ hc->pci_origmembase = hc->pci_dev->resource[1].start;
+ if (!hc->pci_origmembase) {
+ printk(KERN_WARNING
+ "HFC-multi: No IO-Memory for PCI card found\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ hc->pci_membase = ioremap(hc->pci_origmembase, 256);
+ if (!hc->pci_membase) {
+ printk(KERN_WARNING
+ "HFC-multi: failed to remap io address space. "
+ "(internal error)\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+ printk(KERN_INFO "card %d: defined at MEMBASE %#lx (%#lx) IRQ %d "
+ "HZ %d leds-type %d\n", hc->id, (u_long)hc->pci_membase,
+ hc->pci_origmembase, hc->pci_dev->irq, HZ, hc->leds);
+ pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_MEMIO);
+ break;
+ case HFC_IO_MODE_REGIO:
+ hc->pci_iobase = (u_int) hc->pci_dev->resource[0].start;
+ if (!hc->pci_iobase) {
+ printk(KERN_WARNING
+ "HFC-multi: No IO for PCI card found\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ if (!request_region(hc->pci_iobase, 8, "hfcmulti")) {
+ printk(KERN_WARNING "HFC-multi: failed to request "
+ "address space at 0x%08lx (internal error)\n",
+ hc->pci_iobase);
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ printk(KERN_INFO
+ "%s %s: defined at IOBASE %#x IRQ %d HZ %d leds-type %d\n",
+ m->vendor_name, m->card_name, (u_int) hc->pci_iobase,
+ hc->pci_dev->irq, HZ, hc->leds);
+ pci_write_config_word(hc->pci_dev, PCI_COMMAND, PCI_ENA_REGIO);
+ break;
+ default:
+ printk(KERN_WARNING "HFC-multi: Invalid IO mode.\n");
+ pci_disable_device(hc->pci_dev);
+ return -EIO;
+ }
+
+ pci_set_drvdata(hc->pci_dev, hc);
+
+ /* At this point the needed PCI config is done */
+ /* fifos are still not enabled */
+ return 0;
+}
+
+
+/*
+ * remove port
+ */
+
+static void
+release_port(struct hfc_multi *hc, struct dchannel *dch)
+{
+ int pt, ci, i = 0;
+ u_long flags;
+ struct bchannel *pb;
+
+ ci = dch->slot;
+ pt = hc->chan[ci].port;
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: entered for port %d\n",
+ __func__, pt + 1);
+
+ if (pt >= hc->ports) {
+ printk(KERN_WARNING "%s: ERROR port out of range (%d).\n",
+ __func__, pt + 1);
+ return;
+ }
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: releasing port=%d\n",
+ __func__, pt + 1);
+
+ if (dch->dev.D.protocol == ISDN_P_TE_S0)
+ l1_event(dch->l1, CLOSE_CHANNEL);
+
+ hc->chan[ci].dch = NULL;
+
+ if (hc->created[pt]) {
+ hc->created[pt] = 0;
+ mISDN_unregister_device(&dch->dev);
+ }
+
+ spin_lock_irqsave(&hc->lock, flags);
+
+ if (dch->timer.function) {
+ del_timer(&dch->timer);
+ dch->timer.function = NULL;
+ }
+
+ if (hc->type == 1) { /* E1 */
+ /* remove sync */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ hc->syncronized = 0;
+ plxsd_checksync(hc, 1);
+ }
+ /* free channels */
+ for (i = 0; i <= 31; i++) {
+ if (hc->chan[i].bch) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: free port %d channel %d\n",
+ __func__, hc->chan[i].port+1, i);
+ pb = hc->chan[i].bch;
+ hc->chan[i].bch = NULL;
+ spin_unlock_irqrestore(&hc->lock, flags);
+ mISDN_freebchannel(pb);
+ kfree(pb);
+ kfree(hc->chan[i].coeff);
+ spin_lock_irqsave(&hc->lock, flags);
+ }
+ }
+ } else {
+ /* remove sync */
+ if (test_bit(HFC_CHIP_PLXSD, &hc->chip)) {
+ hc->syncronized &=
+ ~(1 << hc->chan[ci].port);
+ plxsd_checksync(hc, 1);
+ }
+ /* free channels */
+ if (hc->chan[ci - 2].bch) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: free port %d channel %d\n",
+ __func__, hc->chan[ci - 2].port+1,
+ ci - 2);
+ pb = hc->chan[ci - 2].bch;
+ hc->chan[ci - 2].bch = NULL;
+ spin_unlock_irqrestore(&hc->lock, flags);
+ mISDN_freebchannel(pb);
+ kfree(pb);
+ kfree(hc->chan[ci - 2].coeff);
+ spin_lock_irqsave(&hc->lock, flags);
+ }
+ if (hc->chan[ci - 1].bch) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: free port %d channel %d\n",
+ __func__, hc->chan[ci - 1].port+1,
+ ci - 1);
+ pb = hc->chan[ci - 1].bch;
+ hc->chan[ci - 1].bch = NULL;
+ spin_unlock_irqrestore(&hc->lock, flags);
+ mISDN_freebchannel(pb);
+ kfree(pb);
+ kfree(hc->chan[ci - 1].coeff);
+ spin_lock_irqsave(&hc->lock, flags);
+ }
+ }
+
+ spin_unlock_irqrestore(&hc->lock, flags);
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: free port %d channel D\n", __func__, pt);
+ mISDN_freedchannel(dch);
+ kfree(dch);
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: done!\n", __func__);
+}
+
+static void
+release_card(struct hfc_multi *hc)
+{
+ u_long flags;
+ int ch;
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: release card (%d) entered\n",
+ __func__, hc->id);
+
+ spin_lock_irqsave(&hc->lock, flags);
+ disable_hwirq(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+
+ udelay(1000);
+
+ /* dimm leds */
+ if (hc->leds)
+ hfcmulti_leds(hc);
+
+ /* disable D-channels & B-channels */
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: disable all channels (d and b)\n",
+ __func__);
+ for (ch = 0; ch <= 31; ch++) {
+ if (hc->chan[ch].dch)
+ release_port(hc, hc->chan[ch].dch);
+ }
+
+ /* release hardware & irq */
+ if (hc->irq) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: free irq %d\n",
+ __func__, hc->irq);
+ free_irq(hc->irq, hc);
+ hc->irq = 0;
+
+ }
+ release_io_hfcmulti(hc);
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: remove instance from list\n",
+ __func__);
+ list_del(&hc->list);
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: delete instance\n", __func__);
+ if (hc == syncmaster)
+ syncmaster = NULL;
+ kfree(hc);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_WARNING "%s: card successfully removed\n",
+ __func__);
+}
+
+static int
+init_e1_port(struct hfc_multi *hc, struct hm_map *m)
+{
+ struct dchannel *dch;
+ struct bchannel *bch;
+ int ch, ret = 0;
+ char name[MISDN_MAX_IDLEN];
+
+ dch = kzalloc(sizeof(struct dchannel), GFP_KERNEL);
+ if (!dch)
+ return -ENOMEM;
+ dch->debug = debug;
+ mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change);
+ dch->hw = hc;
+ dch->dev.Dprotocols = (1 << ISDN_P_TE_E1) | (1 << ISDN_P_NT_E1);
+ dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) |
+ (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK));
+ dch->dev.D.send = handle_dmsg;
+ dch->dev.D.ctrl = hfcm_dctrl;
+ dch->dev.nrbchan = (hc->dslot)?30:31;
+ dch->slot = hc->dslot;
+ hc->chan[hc->dslot].dch = dch;
+ hc->chan[hc->dslot].port = 0;
+ hc->chan[hc->dslot].nt_timer = -1;
+ for (ch = 1; ch <= 31; ch++) {
+ if (ch == hc->dslot) /* skip dchannel */
+ continue;
+ bch = kzalloc(sizeof(struct bchannel), GFP_KERNEL);
+ if (!bch) {
+ printk(KERN_ERR "%s: no memory for bchannel\n",
+ __func__);
+ ret = -ENOMEM;
+ goto free_chan;
+ }
+ hc->chan[ch].coeff = kzalloc(512, GFP_KERNEL);
+ if (!hc->chan[ch].coeff) {
+ printk(KERN_ERR "%s: no memory for coeffs\n",
+ __func__);
+ ret = -ENOMEM;
+ goto free_chan;
+ }
+ bch->nr = ch;
+ bch->slot = ch;
+ bch->debug = debug;
+ mISDN_initbchannel(bch, MAX_DATA_MEM);
+ bch->hw = hc;
+ bch->ch.send = handle_bmsg;
+ bch->ch.ctrl = hfcm_bctrl;
+ bch->ch.nr = ch;
+ list_add(&bch->ch.list, &dch->dev.bchannels);
+ hc->chan[ch].bch = bch;
+ hc->chan[ch].port = 0;
+ test_and_set_bit(bch->nr, &dch->dev.channelmap[0]);
+ }
+ /* set optical line type */
+ if (port[Port_cnt] & 0x001) {
+ if (!m->opticalsupport) {
+ printk(KERN_INFO
+ "This board has no optical "
+ "support\n");
+ } else {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PORT set optical "
+ "interfacs: card(%d) "
+ "port(%d)\n",
+ __func__,
+ HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_OPTICAL,
+ &hc->chan[hc->dslot].cfg);
+ }
+ }
+ /* set LOS report */
+ if (port[Port_cnt] & 0x004) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT set "
+ "LOS report: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_REPORT_LOS,
+ &hc->chan[hc->dslot].cfg);
+ }
+ /* set AIS report */
+ if (port[Port_cnt] & 0x008) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT set "
+ "AIS report: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_REPORT_AIS,
+ &hc->chan[hc->dslot].cfg);
+ }
+ /* set SLIP report */
+ if (port[Port_cnt] & 0x010) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PORT set SLIP report: "
+ "card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_REPORT_SLIP,
+ &hc->chan[hc->dslot].cfg);
+ }
+ /* set RDI report */
+ if (port[Port_cnt] & 0x020) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PORT set RDI report: "
+ "card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_REPORT_RDI,
+ &hc->chan[hc->dslot].cfg);
+ }
+ /* set CRC-4 Mode */
+ if (!(port[Port_cnt] & 0x100)) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT turn on CRC4 report:"
+ " card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CFG_CRC4,
+ &hc->chan[hc->dslot].cfg);
+ } else {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT turn off CRC4"
+ " report: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ }
+ /* set forced clock */
+ if (port[Port_cnt] & 0x0200) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT force getting clock from "
+ "E1: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CHIP_E1CLOCK_GET, &hc->chip);
+ } else
+ if (port[Port_cnt] & 0x0400) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT force putting clock to "
+ "E1: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CHIP_E1CLOCK_PUT, &hc->chip);
+ }
+ /* set JATT PLL */
+ if (port[Port_cnt] & 0x0800) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: PORT disable JATT PLL on "
+ "E1: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, 1);
+ test_and_set_bit(HFC_CHIP_RX_SYNC, &hc->chip);
+ }
+ /* set elastic jitter buffer */
+ if (port[Port_cnt] & 0x3000) {
+ hc->chan[hc->dslot].jitter = (port[Port_cnt]>>12) & 0x3;
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PORT set elastic "
+ "buffer to %d: card(%d) port(%d)\n",
+ __func__, hc->chan[hc->dslot].jitter,
+ HFC_cnt + 1, 1);
+ } else
+ hc->chan[hc->dslot].jitter = 2; /* default */
+ snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-e1.%d", HFC_cnt + 1);
+ ret = mISDN_register_device(&dch->dev, name);
+ if (ret)
+ goto free_chan;
+ hc->created[0] = 1;
+ return ret;
+free_chan:
+ release_port(hc, dch);
+ return ret;
+}
+
+static int
+init_multi_port(struct hfc_multi *hc, int pt)
+{
+ struct dchannel *dch;
+ struct bchannel *bch;
+ int ch, i, ret = 0;
+ char name[MISDN_MAX_IDLEN];
+
+ dch = kzalloc(sizeof(struct dchannel), GFP_KERNEL);
+ if (!dch)
+ return -ENOMEM;
+ dch->debug = debug;
+ mISDN_initdchannel(dch, MAX_DFRAME_LEN_L1, ph_state_change);
+ dch->hw = hc;
+ dch->dev.Dprotocols = (1 << ISDN_P_TE_S0) | (1 << ISDN_P_NT_S0);
+ dch->dev.Bprotocols = (1 << (ISDN_P_B_RAW & ISDN_P_B_MASK)) |
+ (1 << (ISDN_P_B_HDLC & ISDN_P_B_MASK));
+ dch->dev.D.send = handle_dmsg;
+ dch->dev.D.ctrl = hfcm_dctrl;
+ dch->dev.nrbchan = 2;
+ i = pt << 2;
+ dch->slot = i + 2;
+ hc->chan[i + 2].dch = dch;
+ hc->chan[i + 2].port = pt;
+ hc->chan[i + 2].nt_timer = -1;
+ for (ch = 0; ch < dch->dev.nrbchan; ch++) {
+ bch = kzalloc(sizeof(struct bchannel), GFP_KERNEL);
+ if (!bch) {
+ printk(KERN_ERR "%s: no memory for bchannel\n",
+ __func__);
+ ret = -ENOMEM;
+ goto free_chan;
+ }
+ hc->chan[i + ch].coeff = kzalloc(512, GFP_KERNEL);
+ if (!hc->chan[i + ch].coeff) {
+ printk(KERN_ERR "%s: no memory for coeffs\n",
+ __func__);
+ ret = -ENOMEM;
+ goto free_chan;
+ }
+ bch->nr = ch + 1;
+ bch->slot = i + ch;
+ bch->debug = debug;
+ mISDN_initbchannel(bch, MAX_DATA_MEM);
+ bch->hw = hc;
+ bch->ch.send = handle_bmsg;
+ bch->ch.ctrl = hfcm_bctrl;
+ bch->ch.nr = ch + 1;
+ list_add(&bch->ch.list, &dch->dev.bchannels);
+ hc->chan[i + ch].bch = bch;
+ hc->chan[i + ch].port = pt;
+ test_and_set_bit(bch->nr, &dch->dev.channelmap[0]);
+ }
+ /* set master clock */
+ if (port[Port_cnt] & 0x001) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PROTOCOL set master clock: "
+ "card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, pt + 1);
+ if (dch->dev.D.protocol != ISDN_P_TE_S0) {
+ printk(KERN_ERR "Error: Master clock "
+ "for port(%d) of card(%d) is only"
+ " possible with TE-mode\n",
+ pt + 1, HFC_cnt + 1);
+ ret = -EINVAL;
+ goto free_chan;
+ }
+ if (hc->masterclk >= 0) {
+ printk(KERN_ERR "Error: Master clock "
+ "for port(%d) of card(%d) already "
+ "defined for port(%d)\n",
+ pt + 1, HFC_cnt + 1, hc->masterclk+1);
+ ret = -EINVAL;
+ goto free_chan;
+ }
+ hc->masterclk = pt;
+ }
+ /* set transmitter line to non capacitive */
+ if (port[Port_cnt] & 0x002) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PROTOCOL set non capacitive "
+ "transmitter: card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, pt + 1);
+ test_and_set_bit(HFC_CFG_NONCAP_TX,
+ &hc->chan[i + 2].cfg);
+ }
+ /* disable E-channel */
+ if (port[Port_cnt] & 0x004) {
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: PROTOCOL disable E-channel: "
+ "card(%d) port(%d)\n",
+ __func__, HFC_cnt + 1, pt + 1);
+ test_and_set_bit(HFC_CFG_DIS_ECHANNEL,
+ &hc->chan[i + 2].cfg);
+ }
+ snprintf(name, MISDN_MAX_IDLEN - 1, "hfc-%ds.%d/%d",
+ hc->type, HFC_cnt + 1, pt + 1);
+ ret = mISDN_register_device(&dch->dev, name);
+ if (ret)
+ goto free_chan;
+ hc->created[pt] = 1;
+ return ret;
+free_chan:
+ release_port(hc, dch);
+ return ret;
+}
+
+static int
+hfcmulti_init(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct hm_map *m = (struct hm_map *)ent->driver_data;
+ int ret_err = 0;
+ int pt;
+ struct hfc_multi *hc;
+ u_long flags;
+ u_char dips = 0, pmj = 0; /* dip settings, port mode Jumpers */
+
+ if (HFC_cnt >= MAX_CARDS) {
+ printk(KERN_ERR "too many cards (max=%d).\n",
+ MAX_CARDS);
+ return -EINVAL;
+ }
+ if ((type[HFC_cnt] & 0xff) && (type[HFC_cnt] & 0xff) != m->type) {
+ printk(KERN_WARNING "HFC-MULTI: Card '%s:%s' type %d found but "
+ "type[%d] %d was supplied as module parameter\n",
+ m->vendor_name, m->card_name, m->type, HFC_cnt,
+ type[HFC_cnt] & 0xff);
+ printk(KERN_WARNING "HFC-MULTI: Load module without parameters "
+ "first, to see cards and their types.");
+ return -EINVAL;
+ }
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: Registering %s:%s chip type %d (0x%x)\n",
+ __func__, m->vendor_name, m->card_name, m->type,
+ type[HFC_cnt]);
+
+ /* allocate card+fifo structure */
+ hc = kzalloc(sizeof(struct hfc_multi), GFP_KERNEL);
+ if (!hc) {
+ printk(KERN_ERR "No kmem for HFC-Multi card\n");
+ return -ENOMEM;
+ }
+ spin_lock_init(&hc->lock);
+ hc->mtyp = m;
+ hc->type = m->type;
+ hc->ports = m->ports;
+ hc->id = HFC_cnt;
+ hc->pcm = pcm[HFC_cnt];
+ hc->io_mode = iomode[HFC_cnt];
+ if (dslot[HFC_cnt] < 0) {
+ hc->dslot = 0;
+ printk(KERN_INFO "HFC-E1 card has disabled D-channel, but "
+ "31 B-channels\n");
+ } if (dslot[HFC_cnt] > 0 && dslot[HFC_cnt] < 32) {
+ hc->dslot = dslot[HFC_cnt];
+ printk(KERN_INFO "HFC-E1 card has alternating D-channel on "
+ "time slot %d\n", dslot[HFC_cnt]);
+ } else
+ hc->dslot = 16;
+
+ /* set chip specific features */
+ hc->masterclk = -1;
+ if (type[HFC_cnt] & 0x100) {
+ test_and_set_bit(HFC_CHIP_ULAW, &hc->chip);
+ silence = 0xff; /* ulaw silence */
+ } else
+ silence = 0x2a; /* alaw silence */
+ if (!(type[HFC_cnt] & 0x200))
+ test_and_set_bit(HFC_CHIP_DTMF, &hc->chip);
+
+ if (type[HFC_cnt] & 0x800)
+ test_and_set_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
+ if (type[HFC_cnt] & 0x1000) {
+ test_and_set_bit(HFC_CHIP_PCM_MASTER, &hc->chip);
+ test_and_clear_bit(HFC_CHIP_PCM_SLAVE, &hc->chip);
+ }
+ if (type[HFC_cnt] & 0x4000)
+ test_and_set_bit(HFC_CHIP_EXRAM_128, &hc->chip);
+ if (type[HFC_cnt] & 0x8000)
+ test_and_set_bit(HFC_CHIP_EXRAM_512, &hc->chip);
+ hc->slots = 32;
+ if (type[HFC_cnt] & 0x10000)
+ hc->slots = 64;
+ if (type[HFC_cnt] & 0x20000)
+ hc->slots = 128;
+ if (type[HFC_cnt] & 0x80000) {
+ test_and_set_bit(HFC_CHIP_WATCHDOG, &hc->chip);
+ hc->wdcount = 0;
+ hc->wdbyte = V_GPIO_OUT2;
+ printk(KERN_NOTICE "Watchdog enabled\n");
+ }
+
+ /* setup pci, hc->slots may change due to PLXSD */
+ ret_err = setup_pci(hc, pdev, ent);
+ if (ret_err) {
+ if (hc == syncmaster)
+ syncmaster = NULL;
+ kfree(hc);
+ return ret_err;
+ }
+
+ /* crate channels */
+ for (pt = 0; pt < hc->ports; pt++) {
+ if (Port_cnt >= MAX_PORTS) {
+ printk(KERN_ERR "too many ports (max=%d).\n",
+ MAX_PORTS);
+ ret_err = -EINVAL;
+ goto free_card;
+ }
+ if (hc->type == 1)
+ ret_err = init_e1_port(hc, m);
+ else
+ ret_err = init_multi_port(hc, pt);
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG
+ "%s: Registering D-channel, card(%d) port(%d)"
+ "result %d\n",
+ __func__, HFC_cnt + 1, pt, ret_err);
+
+ if (ret_err) {
+ while (pt) { /* release already registered ports */
+ pt--;
+ release_port(hc, hc->chan[(pt << 2) + 2].dch);
+ }
+ goto free_card;
+ }
+ Port_cnt++;
+ }
+
+ /* disp switches */
+ switch (m->dip_type) {
+ case DIP_4S:
+ /*
+ * get DIP Setting for beroNet 1S/2S/4S cards
+ * check if Port Jumper config matches
+ * module param 'protocol'
+ * DIP Setting: (collect GPIO 13/14/15 (R_GPIO_IN1) +
+ * GPI 19/23 (R_GPI_IN2))
+ */
+ dips = ((~HFC_inb(hc, R_GPIO_IN1) & 0xE0) >> 5) |
+ ((~HFC_inb(hc, R_GPI_IN2) & 0x80) >> 3) |
+ (~HFC_inb(hc, R_GPI_IN2) & 0x08);
+
+ /* Port mode (TE/NT) jumpers */
+ pmj = ((HFC_inb(hc, R_GPI_IN3) >> 4) & 0xf);
+
+ if (test_bit(HFC_CHIP_B410P, &hc->chip))
+ pmj = ~pmj & 0xf;
+
+ printk(KERN_INFO "%s: %s DIPs(0x%x) jumpers(0x%x)\n",
+ m->vendor_name, m->card_name, dips, pmj);
+ break;
+ case DIP_8S:
+ /*
+ * get DIP Setting for beroNet 8S0+ cards
+ *
+ * enable PCI auxbridge function
+ */
+ HFC_outb(hc, R_BRG_PCM_CFG, 1 | V_PCM_CLK);
+ /* prepare access to auxport */
+ outw(0x4000, hc->pci_iobase + 4);
+ /*
+ * some dummy reads are required to
+ * read valid DIP switch data
+ */
+ dips = inb(hc->pci_iobase);
+ dips = inb(hc->pci_iobase);
+ dips = inb(hc->pci_iobase);
+ dips = ~inb(hc->pci_iobase) & 0x3F;
+ outw(0x0, hc->pci_iobase + 4);
+ /* disable PCI auxbridge function */
+ HFC_outb(hc, R_BRG_PCM_CFG, V_PCM_CLK);
+ printk(KERN_INFO "%s: %s DIPs(0x%x)\n",
+ m->vendor_name, m->card_name, dips);
+ break;
+ case DIP_E1:
+ /*
+ * get DIP Setting for beroNet E1 cards
+ * DIP Setting: collect GPI 4/5/6/7 (R_GPI_IN0)
+ */
+ dips = (~HFC_inb(hc, R_GPI_IN0) & 0xF0)>>4;
+ printk(KERN_INFO "%s: %s DIPs(0x%x)\n",
+ m->vendor_name, m->card_name, dips);
+ break;
+ }
+
+ /* add to list */
+ spin_lock_irqsave(&HFClock, flags);
+ list_add_tail(&hc->list, &HFClist);
+ spin_unlock_irqrestore(&HFClock, flags);
+
+ /* initialize hardware */
+ ret_err = init_card(hc);
+ if (ret_err) {
+ printk(KERN_ERR "init card returns %d\n", ret_err);
+ release_card(hc);
+ return ret_err;
+ }
+
+ /* start IRQ and return */
+ spin_lock_irqsave(&hc->lock, flags);
+ enable_hwirq(hc);
+ spin_unlock_irqrestore(&hc->lock, flags);
+ return 0;
+
+free_card:
+ release_io_hfcmulti(hc);
+ if (hc == syncmaster)
+ syncmaster = NULL;
+ kfree(hc);
+ return ret_err;
+}
+
+static void __devexit hfc_remove_pci(struct pci_dev *pdev)
+{
+ struct hfc_multi *card = pci_get_drvdata(pdev);
+ u_long flags;
+
+ if (debug)
+ printk(KERN_INFO "removing hfc_multi card vendor:%x "
+ "device:%x subvendor:%x subdevice:%x\n",
+ pdev->vendor, pdev->device,
+ pdev->subsystem_vendor, pdev->subsystem_device);
+
+ if (card) {
+ spin_lock_irqsave(&HFClock, flags);
+ release_card(card);
+ spin_unlock_irqrestore(&HFClock, flags);
+ } else {
+ if (debug)
+ printk(KERN_WARNING "%s: drvdata allready removed\n",
+ __func__);
+ }
+}
+
+#define VENDOR_CCD "Cologne Chip AG"
+#define VENDOR_BN "beroNet GmbH"
+#define VENDOR_DIG "Digium Inc."
+#define VENDOR_JH "Junghanns.NET GmbH"
+#define VENDOR_PRIM "PrimuX"
+
+static const struct hm_map hfcm_map[] = {
+/*0*/ {VENDOR_BN, "HFC-1S Card (mini PCI)", 4, 1, 1, 3, 0, DIP_4S, 0},
+/*1*/ {VENDOR_BN, "HFC-2S Card", 4, 2, 1, 3, 0, DIP_4S},
+/*2*/ {VENDOR_BN, "HFC-2S Card (mini PCI)", 4, 2, 1, 3, 0, DIP_4S, 0},
+/*3*/ {VENDOR_BN, "HFC-4S Card", 4, 4, 1, 2, 0, DIP_4S, 0},
+/*4*/ {VENDOR_BN, "HFC-4S Card (mini PCI)", 4, 4, 1, 2, 0, 0, 0},
+/*5*/ {VENDOR_CCD, "HFC-4S Eval (old)", 4, 4, 0, 0, 0, 0, 0},
+/*6*/ {VENDOR_CCD, "HFC-4S IOB4ST", 4, 4, 1, 2, 0, 0, 0},
+/*7*/ {VENDOR_CCD, "HFC-4S", 4, 4, 1, 2, 0, 0, 0},
+/*8*/ {VENDOR_DIG, "HFC-4S Card", 4, 4, 0, 2, 0, 0, HFC_IO_MODE_REGIO},
+/*9*/ {VENDOR_CCD, "HFC-4S Swyx 4xS0 SX2 QuadBri", 4, 4, 1, 2, 0, 0, 0},
+/*10*/ {VENDOR_JH, "HFC-4S (junghanns 2.0)", 4, 4, 1, 2, 0, 0, 0},
+/*11*/ {VENDOR_PRIM, "HFC-2S Primux Card", 4, 2, 0, 0, 0, 0, 0},
+
+/*12*/ {VENDOR_BN, "HFC-8S Card", 8, 8, 1, 0, 0, 0, 0},
+/*13*/ {VENDOR_BN, "HFC-8S Card (+)", 8, 8, 1, 8, 0, DIP_8S,
+ HFC_IO_MODE_REGIO},
+/*14*/ {VENDOR_CCD, "HFC-8S Eval (old)", 8, 8, 0, 0, 0, 0, 0},
+/*15*/ {VENDOR_CCD, "HFC-8S IOB4ST Recording", 8, 8, 1, 0, 0, 0, 0},
+
+/*16*/ {VENDOR_CCD, "HFC-8S IOB8ST", 8, 8, 1, 0, 0, 0, 0},
+/*17*/ {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0},
+/*18*/ {VENDOR_CCD, "HFC-8S", 8, 8, 1, 0, 0, 0, 0},
+
+/*19*/ {VENDOR_BN, "HFC-E1 Card", 1, 1, 0, 1, 0, DIP_E1, 0},
+/*20*/ {VENDOR_BN, "HFC-E1 Card (mini PCI)", 1, 1, 0, 1, 0, 0, 0},
+/*21*/ {VENDOR_BN, "HFC-E1+ Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0},
+/*22*/ {VENDOR_BN, "HFC-E1 Card (Dual)", 1, 1, 0, 1, 0, DIP_E1, 0},
+
+/*23*/ {VENDOR_CCD, "HFC-E1 Eval (old)", 1, 1, 0, 0, 0, 0, 0},
+/*24*/ {VENDOR_CCD, "HFC-E1 IOB1E1", 1, 1, 0, 1, 0, 0, 0},
+/*25*/ {VENDOR_CCD, "HFC-E1", 1, 1, 0, 1, 0, 0, 0},
+
+/*26*/ {VENDOR_CCD, "HFC-4S Speech Design", 4, 4, 0, 0, 0, 0,
+ HFC_IO_MODE_PLXSD},
+/*27*/ {VENDOR_CCD, "HFC-E1 Speech Design", 1, 1, 0, 0, 0, 0,
+ HFC_IO_MODE_PLXSD},
+/*28*/ {VENDOR_CCD, "HFC-4S OpenVox", 4, 4, 1, 0, 0, 0, 0},
+/*29*/ {VENDOR_CCD, "HFC-2S OpenVox", 4, 2, 1, 0, 0, 0, 0},
+/*30*/ {VENDOR_CCD, "HFC-8S OpenVox", 8, 8, 1, 0, 0, 0, 0},
+};
+
+#undef H
+#define H(x) ((unsigned long)&hfcm_map[x])
+static struct pci_device_id hfmultipci_ids[] __devinitdata = {
+
+ /* Cards with HFC-4S Chip */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN1SM, 0, 0, H(0)}, /* BN1S mini PCI */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN2S, 0, 0, H(1)}, /* BN2S */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN2SM, 0, 0, H(2)}, /* BN2S mini PCI */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN4S, 0, 0, H(3)}, /* BN4S */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN4SM, 0, 0, H(4)}, /* BN4S mini PCI */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_DEVICE_ID_CCD_HFC4S, 0, 0, H(5)}, /* Old Eval */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_IOB4ST, 0, 0, H(6)}, /* IOB4ST */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_HFC4S, 0, 0, H(7)}, /* 4S */
+ { PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S,
+ PCI_VENDOR_ID_DIGIUM, PCI_DEVICE_ID_DIGIUM_HFC4S, 0, 0, H(8)},
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_SWYX4S, 0, 0, H(9)}, /* 4S Swyx */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_JH4S20, 0, 0, H(10)},
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_PMX2S, 0, 0, H(11)}, /* Primux */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_OV4S, 0, 0, H(28)}, /* OpenVox 4 */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_OV2S, 0, 0, H(29)}, /* OpenVox 2 */
+
+ /* Cards with HFC-8S Chip */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN8S, 0, 0, H(12)}, /* BN8S */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BN8SP, 0, 0, H(13)}, /* BN8S+ */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_DEVICE_ID_CCD_HFC8S, 0, 0, H(14)}, /* old Eval */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_IOB8STR, 0, 0, H(15)},
+ /* IOB8ST Recording */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_IOB8ST, 0, 0, H(16)}, /* IOB8ST */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_IOB8ST_1, 0, 0, H(17)}, /* IOB8ST */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_HFC8S, 0, 0, H(18)}, /* 8S */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_OV8S, 0, 0, H(30)}, /* OpenVox 8 */
+
+
+ /* Cards with HFC-E1 Chip */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BNE1, 0, 0, H(19)}, /* BNE1 */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BNE1M, 0, 0, H(20)}, /* BNE1 mini PCI */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BNE1DP, 0, 0, H(21)}, /* BNE1 + (Dual) */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_BNE1D, 0, 0, H(22)}, /* BNE1 (Dual) */
+
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_DEVICE_ID_CCD_HFCE1, 0, 0, H(23)}, /* Old Eval */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_IOB1E1, 0, 0, H(24)}, /* IOB1E1 */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_HFCE1, 0, 0, H(25)}, /* E1 */
+
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_SPD4S, 0, 0, H(26)}, /* PLX PCI Bridge */
+ { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9030, PCI_VENDOR_ID_CCD,
+ PCI_SUBDEVICE_ID_CCD_SPDE1, 0, 0, H(27)}, /* PLX PCI Bridge */
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC4S, PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, 0},
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFC8S, PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, 0},
+ { PCI_VENDOR_ID_CCD, PCI_DEVICE_ID_CCD_HFCE1, PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, 0},
+ {0, }
+};
+#undef H
+
+MODULE_DEVICE_TABLE(pci, hfmultipci_ids);
+
+static int
+hfcmulti_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct hm_map *m = (struct hm_map *)ent->driver_data;
+ int ret;
+
+ if (m == NULL) {
+ if (ent->vendor == PCI_VENDOR_ID_CCD)
+ if (ent->device == PCI_DEVICE_ID_CCD_HFC4S ||
+ ent->device == PCI_DEVICE_ID_CCD_HFC8S ||
+ ent->device == PCI_DEVICE_ID_CCD_HFCE1)
+ printk(KERN_ERR
+ "unknown HFC multiport controller "
+ "(vendor:%x device:%x subvendor:%x "
+ "subdevice:%x) Please contact the "
+ "driver maintainer for support.\n",
+ ent->vendor, ent->device,
+ ent->subvendor, ent->subdevice);
+ return -ENODEV;
+ }
+ ret = hfcmulti_init(pdev, ent);
+ if (ret)
+ return ret;
+ HFC_cnt++;
+ printk(KERN_INFO "%d devices registered\n", HFC_cnt);
+ return 0;
+}
+
+static struct pci_driver hfcmultipci_driver = {
+ .name = "hfc_multi",
+ .probe = hfcmulti_probe,
+ .remove = __devexit_p(hfc_remove_pci),
+ .id_table = hfmultipci_ids,
+};
+
+static void __exit
+HFCmulti_cleanup(void)
+{
+ struct hfc_multi *card, *next;
+
+ /* unload interrupt function symbol */
+ if (hfc_interrupt)
+ symbol_put(ztdummy_extern_interrupt);
+ if (register_interrupt)
+ symbol_put(ztdummy_register_interrupt);
+ if (unregister_interrupt) {
+ if (interrupt_registered) {
+ interrupt_registered = 0;
+ unregister_interrupt();
+ }
+ symbol_put(ztdummy_unregister_interrupt);
+ }
+
+ list_for_each_entry_safe(card, next, &HFClist, list)
+ release_card(card);
+ /* get rid of all devices of this driver */
+ pci_unregister_driver(&hfcmultipci_driver);
+}
+
+static int __init
+HFCmulti_init(void)
+{
+ int err;
+
+#ifdef IRQ_DEBUG
+ printk(KERN_ERR "%s: IRQ_DEBUG IS ENABLED!\n", __func__);
+#endif
+
+ spin_lock_init(&HFClock);
+ spin_lock_init(&plx_lock);
+
+ if (debug & DEBUG_HFCMULTI_INIT)
+ printk(KERN_DEBUG "%s: init entered\n", __func__);
+
+#ifdef __BIG_ENDIAN
+#error "not running on big endian machines now"
+#endif
+ hfc_interrupt = symbol_get(ztdummy_extern_interrupt);
+ register_interrupt = symbol_get(ztdummy_register_interrupt);
+ unregister_interrupt = symbol_get(ztdummy_unregister_interrupt);
+ printk(KERN_INFO "mISDN: HFC-multi driver %s\n",
+ hfcmulti_revision);
+
+ switch (poll) {
+ case 0:
+ poll_timer = 6;
+ poll = 128;
+ break;
+ /*
+ * wenn dieses break nochmal verschwindet,
+ * gibt es heisse ohren :-)
+ * "without the break you will get hot ears ???"
+ */
+ case 8:
+ poll_timer = 2;
+ break;
+ case 16:
+ poll_timer = 3;
+ break;
+ case 32:
+ poll_timer = 4;
+ break;
+ case 64:
+ poll_timer = 5;
+ break;
+ case 128:
+ poll_timer = 6;
+ break;
+ case 256:
+ poll_timer = 7;
+ break;
+ default:
+ printk(KERN_ERR
+ "%s: Wrong poll value (%d).\n", __func__, poll);
+ err = -EINVAL;
+ return err;
+
+ }
+
+ err = pci_register_driver(&hfcmultipci_driver);
+ if (err < 0) {
+ printk(KERN_ERR "error registering pci driver: %x\n", err);
+ if (hfc_interrupt)
+ symbol_put(ztdummy_extern_interrupt);
+ if (register_interrupt)
+ symbol_put(ztdummy_register_interrupt);
+ if (unregister_interrupt) {
+ if (interrupt_registered) {
+ interrupt_registered = 0;
+ unregister_interrupt();
+ }
+ symbol_put(ztdummy_unregister_interrupt);
+ }
+ return err;
+ }
+ return 0;
+}
+
+
+module_init(HFCmulti_init);
+module_exit(HFCmulti_cleanup);
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index c3b1761..ffe479b 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1832,7 +1832,13 @@
#define PCI_DEVICE_ID_MOXA_C320 0x3200
#define PCI_VENDOR_ID_CCD 0x1397
+#define PCI_DEVICE_ID_CCD_HFC4S 0x08B4
+#define PCI_SUBDEVICE_ID_CCD_PMX2S 0x1234
+#define PCI_DEVICE_ID_CCD_HFC8S 0x16B8
#define PCI_DEVICE_ID_CCD_2BD0 0x2bd0
+#define PCI_DEVICE_ID_CCD_HFCE1 0x30B1
+#define PCI_SUBDEVICE_ID_CCD_SPD4S 0x3136
+#define PCI_SUBDEVICE_ID_CCD_SPDE1 0x3137
#define PCI_DEVICE_ID_CCD_B000 0xb000
#define PCI_DEVICE_ID_CCD_B006 0xb006
#define PCI_DEVICE_ID_CCD_B007 0xb007
@@ -1842,8 +1848,32 @@
#define PCI_DEVICE_ID_CCD_B00B 0xb00b
#define PCI_DEVICE_ID_CCD_B00C 0xb00c
#define PCI_DEVICE_ID_CCD_B100 0xb100
+#define PCI_SUBDEVICE_ID_CCD_IOB4ST 0xB520
+#define PCI_SUBDEVICE_ID_CCD_IOB8STR 0xB521
+#define PCI_SUBDEVICE_ID_CCD_IOB8ST 0xB522
+#define PCI_SUBDEVICE_ID_CCD_IOB1E1 0xB523
+#define PCI_SUBDEVICE_ID_CCD_SWYX4S 0xB540
+#define PCI_SUBDEVICE_ID_CCD_JH4S20 0xB550
+#define PCI_SUBDEVICE_ID_CCD_IOB8ST_1 0xB552
+#define PCI_SUBDEVICE_ID_CCD_BN4S 0xB560
+#define PCI_SUBDEVICE_ID_CCD_BN8S 0xB562
+#define PCI_SUBDEVICE_ID_CCD_BNE1 0xB563
+#define PCI_SUBDEVICE_ID_CCD_BNE1D 0xB564
+#define PCI_SUBDEVICE_ID_CCD_BNE1DP 0xB565
+#define PCI_SUBDEVICE_ID_CCD_BN2S 0xB566
+#define PCI_SUBDEVICE_ID_CCD_BN1SM 0xB567
+#define PCI_SUBDEVICE_ID_CCD_BN4SM 0xB568
+#define PCI_SUBDEVICE_ID_CCD_BN2SM 0xB569
+#define PCI_SUBDEVICE_ID_CCD_BNE1M 0xB56A
+#define PCI_SUBDEVICE_ID_CCD_BN8SP 0xB56B
+#define PCI_SUBDEVICE_ID_CCD_HFC4S 0xB620
+#define PCI_SUBDEVICE_ID_CCD_HFC8S 0xB622
#define PCI_DEVICE_ID_CCD_B700 0xb700
#define PCI_DEVICE_ID_CCD_B701 0xb701
+#define PCI_SUBDEVICE_ID_CCD_HFCE1 0xC523
+#define PCI_SUBDEVICE_ID_CCD_OV2S 0xE884
+#define PCI_SUBDEVICE_ID_CCD_OV4S 0xE888
+#define PCI_SUBDEVICE_ID_CCD_OV8S 0xE998
#define PCI_VENDOR_ID_EXAR 0x13a8
#define PCI_DEVICE_ID_EXAR_XR17C152 0x0152
@@ -2523,6 +2553,9 @@
#define PCI_VENDOR_ID_3COM_2 0xa727
+#define PCI_VENDOR_ID_DIGIUM 0xd161
+#define PCI_DEVICE_ID_DIGIUM_HFC4S 0xb410
+
#define PCI_SUBVENDOR_ID_EXSYS 0xd84d
#define PCI_SUBDEVICE_ID_EXSYS_4014 0x4014
#define PCI_SUBDEVICE_ID_EXSYS_4055 0x4055
--
1.5.6.4
--
Karsten Keil
SuSE Labs
ISDN and VOIP development
SUSE LINUX Products GmbH, Maxfeldstr.5 90409 Nuernberg, GF: Markus Rex, HRB 16746 (AG Nuernberg)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists