| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <491C0C05.6040301@atmel.com>
Date: Thu, 13 Nov 2008 12:14:13 +0100
From: Nicolas Ferre <nicolas.ferre@...el.com>
To: Haavard Skinnemoen <hskinnemoen@...el.com>,
Pierre Ossman <drzeus@...eus.cx>
CC: Linux Kernel list <linux-kernel@...r.kernel.org>,
kernel@...32linux.org
Subject: [PATCH] mmc: atmel-mci: move atmel-mci.h file to include/linux
Needed to use the atmel-mci driver in a architecture
independent manner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@...el.com>
---
arch/avr32/boards/atngw100/setup.c | 2 +-
arch/avr32/boards/atstk1000/atstk1002.c | 2 +-
arch/avr32/boards/atstk1000/atstk1003.c | 2 +-
arch/avr32/boards/atstk1000/atstk1004.c | 2 +-
arch/avr32/include/asm/atmel-mci.h | 39 ------
arch/avr32/mach-at32ap/at32ap700x.c | 2 +-
drivers/mmc/host/atmel-mci.c | 2 +-
include/linux/atmel-mci.h | 39 ++++++
8 files changed, 45 insertions(+), 45 deletions(-)
delete mode 100644 arch/avr32/include/asm/atmel-mci.h
create mode 100644 include/linux/atmel-mci.h
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c
index 6c54580..ca6e1ff 100644
--- a/arch/avr32/boards/atngw100/setup.c
+++ b/arch/avr32/boards/atngw100/setup.c
@@ -19,8 +19,8 @@
#include <linux/types.h>
#include <linux/leds.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/setup.h>
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index 29e5b51..5a6380f 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -16,12 +16,12 @@
#include <linux/types.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
+#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <asm/io.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
diff --git a/arch/avr32/boards/atstk1000/atstk1003.c b/arch/avr32/boards/atstk1000/atstk1003.c
index be089d7..7b9ceee 100644
--- a/arch/avr32/boards/atstk1000/atstk1003.c
+++ b/arch/avr32/boards/atstk1000/atstk1003.c
@@ -17,9 +17,9 @@
#include <linux/spi/at73c213.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
diff --git a/arch/avr32/boards/atstk1000/atstk1004.c b/arch/avr32/boards/atstk1000/atstk1004.c
index 248ef23..3ff0498 100644
--- a/arch/avr32/boards/atstk1000/atstk1004.c
+++ b/arch/avr32/boards/atstk1000/atstk1004.c
@@ -17,11 +17,11 @@
#include <linux/spi/at73c213.h>
#include <linux/spi/spi.h>
+#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <asm/setup.h>
-#include <asm/atmel-mci.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
diff --git a/arch/avr32/include/asm/atmel-mci.h b/arch/avr32/include/asm/atmel-mci.h
deleted file mode 100644
index 59f3fad..0000000
--- a/arch/avr32/include/asm/atmel-mci.h
+++ /dev/null
@@ -1,39 +0,0 @@
-#ifndef __ASM_AVR32_ATMEL_MCI_H
-#define __ASM_AVR32_ATMEL_MCI_H
-
-#define ATMEL_MCI_MAX_NR_SLOTS 2
-
-struct dma_slave;
-
-/**
- * struct mci_slot_pdata - board-specific per-slot configuration
- * @bus_width: Number of data lines wired up the slot
- * @detect_pin: GPIO pin wired to the card detect switch
- * @wp_pin: GPIO pin wired to the write protect sensor
- *
- * If a given slot is not present on the board, @bus_width should be
- * set to 0. The other fields are ignored in this case.
- *
- * Any pins that aren't available should be set to a negative value.
- *
- * Note that support for multiple slots is experimental -- some cards
- * might get upset if we don't get the clock management exactly right.
- * But in most cases, it should work just fine.
- */
-struct mci_slot_pdata {
- unsigned int bus_width;
- int detect_pin;
- int wp_pin;
-};
-
-/**
- * struct mci_platform_data - board-specific MMC/SDcard configuration
- * @dma_slave: DMA slave interface to use in data transfers, or NULL.
- * @slot: Per-slot configuration data.
- */
-struct mci_platform_data {
- struct dma_slave *dma_slave;
- struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS];
-};
-
-#endif /* __ASM_AVR32_ATMEL_MCI_H */
diff --git a/arch/avr32/mach-at32ap/at32ap700x.c b/arch/avr32/mach-at32ap/at32ap700x.c
index 813b684..b0ad6da 100644
--- a/arch/avr32/mach-at32ap/at32ap700x.c
+++ b/arch/avr32/mach-at32ap/at32ap700x.c
@@ -15,8 +15,8 @@
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/usb/atmel_usba_udc.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/irq.h>
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 7a3f243..1e97916 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -25,8 +25,8 @@
#include <linux/stat.h>
#include <linux/mmc/host.h>
+#include <linux/atmel-mci.h>
-#include <asm/atmel-mci.h>
#include <asm/io.h>
#include <asm/unaligned.h>
diff --git a/include/linux/atmel-mci.h b/include/linux/atmel-mci.h
new file mode 100644
index 0000000..2a2213e
--- /dev/null
+++ b/include/linux/atmel-mci.h
@@ -0,0 +1,39 @@
+#ifndef __LINUX_ATMEL_MCI_H
+#define __LINUX_ATMEL_MCI_H
+
+#define ATMEL_MCI_MAX_NR_SLOTS 2
+
+struct dma_slave;
+
+/**
+ * struct mci_slot_pdata - board-specific per-slot configuration
+ * @bus_width: Number of data lines wired up the slot
+ * @detect_pin: GPIO pin wired to the card detect switch
+ * @wp_pin: GPIO pin wired to the write protect sensor
+ *
+ * If a given slot is not present on the board, @bus_width should be
+ * set to 0. The other fields are ignored in this case.
+ *
+ * Any pins that aren't available should be set to a negative value.
+ *
+ * Note that support for multiple slots is experimental -- some cards
+ * might get upset if we don't get the clock management exactly right.
+ * But in most cases, it should work just fine.
+ */
+struct mci_slot_pdata {
+ unsigned int bus_width;
+ int detect_pin;
+ int wp_pin;
+};
+
+/**
+ * struct mci_platform_data - board-specific MMC/SDcard configuration
+ * @dma_slave: DMA slave interface to use in data transfers, or NULL.
+ * @slot: Per-slot configuration data.
+ */
+struct mci_platform_data {
+ struct dma_slave *dma_slave;
+ struct mci_slot_pdata slot[ATMEL_MCI_MAX_NR_SLOTS];
+};
+
+#endif /* __LINUX_ATMEL_MCI_H */
--
1.5.3.7
--
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists