| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <49798F33.8070906@cfl.rr.com>
Date: Fri, 23 Jan 2009 04:34:43 -0500
From: Mark Hounschell <dmarkh@....rr.com>
To: markh@...pro.net
CC: Andreas Herrmann <andreas.herrmann3@....com>,
john stultz <johnstul@...ibm.com>,
linux-kernel <linux-kernel@...r.kernel.org>,
Thomas Gleixner <tglx@...utronix.de>,
Borislav Petkov <borislav.petkov@....com>
Subject: Re: PROBLEM: Can't boot a (HZ = 1000) kernel using an AMD Phenom-II
processor
Mark Hounschell wrote:
> Andreas Herrmann wrote:
>> On Tue, Jan 20, 2009 at 04:08:41AM -0500, Mark Hounschell wrote:
>>> john stultz wrote:
>>>> On Sun, Jan 18, 2009 at 4:38 AM, Mark Hounschell <dmarkh@....rr.com> wrote:
>>>>> I upgraded from a Phenom to a Phenom-II processor and I could no longer boot.
>>>>>
>>>>> I have tried kernels from 2.6.26 through 2.6.28.
>>>>>
>>>>> I _can_ however boot these kernels when they are configured for HZ = 250. I
>>>>> haven't tried HZ = 300. But certainly if HZ = 1000 the boot hangs at the spot
>>>>> indicated below in the dmesg output.
>>>>>
>>>>> The machine is up and stable running 2.6.26.8 with a (HZ = 1000) configured kernel.
>>>>>
>>>>> While running a 2.6.26.8 kernel configured for HZ = 250:
>>>> [snip]
>>>>> vmalloc : 0xf4800000 - 0xff7fe000 ( 175 MB)
>>>>> lowmem : 0xc0000000 - 0xf4000000 ( 832 MB)
>>>>> .init : 0xc0373000 - 0xc03a9000 ( 216 kB)
>>>>> .data : 0xc02b5336 - 0xc036c6d0 ( 732 kB)
>>>>> .text : 0xc0100000 - 0xc02b5336 (1748 kB)
>>>>> Checking if this processor honours the WP bit even in supervisor mode...Ok.
>>>>>
>>>>>
>>>>> The 2.6.26.8 kernel hangs up right here.
>>>>>
>>>>>
>>>>> CPA: page pool initialized 1 of 1 pages preallocated
>>>>> SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
>>>>> hpet clockevent registered
>>>>> calibrate_delay_direct() failed to get a good estimate for loops_per_jiffy.
>>>> This looks suspect. Probably something is off with the timer
>>>> interrupt, that's causing the calibration to be way off.
>>>>
>>>> Does booting with hpet=disable change anything?
>>>>
>>>> thanks
>>>> -john
>>> John,
>>>
>>> I tried this with 2.6.26, 2.6.28, and 2.6.29-rc2. It didn't change anything.
>> Hi Mark,
>>
>> I just want to second what Boris already stated.
>> Obviously your BIOS doesn't properly initialize your CPU.
>>
>> Your BIOS programs the processor name string as
>> "AMD Processor model unknown"
>>
>> I would have expected to see something like "AMD Phenom(tm) II X4"
>>
>> This shows that the BIOS doesn't know your CPU model and it is an
>> indication that your CPU is not correctly initialized. Phenom II is a
>> different CPU model than Phenom and several configuration bits
>> (e.g. MSRs, CPU config space) need different settings from BIOS
>> or they even were reserved in previous family 10h CPU models.
>>
>> IMHO it is a waste of time to try to debug/fix your problem from OS.
>> First you should update your BIOS. You need to check the "CPU
>> support"-information from your motherboard vendor to see whether your
>> motherboard supports Phenom II and which BIOS is required.
>>
>
> Understood and agreed with.
>
>> If you know that your BIOS/motherboard are supposed to support Phenom II
>> and the problem persists then it is a different game and we should
>> definitely look into your problem.
>>
>> So what's your BIOS version and motherboard vendor/model?
>> (And output of dmidecode would be helpful.)
>>
>>
>
> The MB is a Biostar TA770+. It is not yet listed as one with new
> BIOS support for the Phenom-II. Only the TA770+ SE is at the moment.
> The only difference in the Sata port arrangement and the BIOS type.
>
> I guess I'll just keep pinging them.
>
> Regards
> Mark
>
OK I have now the official bios for this CPU/MB combo. I still cannot boot a
1000 HZ kernel. Here is my new dmesg while running a 250Hz kernel.
Initializing cgroup subsys cpuset
Linux version 2.6.26.8 (root@...ley) (gcc version 4.3.1 20080507 (prerelease)
[gcc-4_3-branch revision 135036] (SUSE Linux) ) #2 SMP PREEMPT Sat Jan 17
16:37:58 EST 2009
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bffe0000 (usable)
BIOS-e820: 00000000bffe0000 - 00000000bffe3000 (ACPI NVS)
BIOS-e820: 00000000bffe3000 - 00000000bfff0000 (ACPI data)
BIOS-e820: 00000000bfff0000 - 00000000c0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Warning only 4GB will be used.
Use a HIGHMEM64G enabled kernel.
3264MB HIGHMEM available.
832MB LOWMEM available.
found SMP MP-table at [c00f3f00] 000f3f00
Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 212992
HighMem 212992 -> 1048576
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 1048576
On node 0 totalpages: 1048576
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1632 pages used for memmap
Normal zone: 207264 pages, LIFO batch:31
HighMem zone: 6528 pages used for memmap
HighMem zone: 829056 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
DMI 2.5 present.
ACPI: RSDP 000F7FB0, 0024 (r2 RX780 )
ACPI: XSDT BFFE3080, 004C (r1 RX780 AWRDACPI 42302E31 AWRD 0)
ACPI: FACP BFFE8C80, 00F4 (r3 RX780 AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT BFFE3200, 5A71 (r1 RX780 AWRDACPI 1000 MSFT 100000E)
ACPI: FACS BFFE0000, 0040
ACPI: SSDT BFFE8E40, 088C (r1 PTLTD POWERNOW 1 LTP 1)
ACPI: HPET BFFE9700, 0038 (r1 RX780 AWRDACPI 42302E31 AWRD 98)
ACPI: MCFG BFFE9740, 003C (r1 RX780 AWRDACPI 42302E31 AWRD 0)
ACPI: APIC BFFE8D80, 0084 (r1 RX780 AWRDACPI 42302E31 AWRD 0)
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x10b9a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
PERCPU: Allocating 38788 bytes of per cpu data
NR_CPUS: 32, nr_cpu_ids: 4
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
Kernel command line: root=/dev/sda5 hwprobe=-modules.pata apm=off selinux=0
noresume splash=silent bigphysarea=0x4000 vmalloc=192M vga=0x317
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Preemptible RCU implementation.
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 3000.279 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3031940k/4194304k available (1748k kernel code, 112564k reserved, 732k
data, 216k init, 2293632k highmem)
virtual kernel memory layout:
fixmap : 0xffe15000 - 0xfffff000 (1960 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf4800000 - 0xff7fe000 ( 175 MB)
lowmem : 0xc0000000 - 0xf4000000 ( 832 MB)
.init : 0xc0373000 - 0xc03a9000 ( 216 kB)
.data : 0xc02b5336 - 0xc036c6d0 ( 732 kB)
.text : 0xc0100000 - 0xc02b5336 (1748 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
hpet clockevent registered
calibrate_delay_direct() failed to get a good estimate for loops_per_jiffy.
Probably due to long platform interrupts. Consider using "lpj=" boot option.
Calibrating delay loop... 3948.54 BogoMIPS (lpj=7897088)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0(4) -> Core 0
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080321
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: AMD Phenom(tm) II X4 940 Processor stepping 02
Booting processor 1/1 ip 2000
Initializing CPU#1
Calibrating delay using timer specific routine.. 6000.48 BogoMIPS (lpj=12000961)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1(4) -> Core 1
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Phenom(tm) II X4 940 Processor stepping 02
Booting processor 2/2 ip 2000
Initializing CPU#2
Calibrating delay using timer specific routine.. 6000.48 BogoMIPS (lpj=12000966)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 2(4) -> Core 2
x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106
CPU2: AMD Phenom(tm) II X4 940 Processor stepping 02
Booting processor 3/3 ip 2000
Initializing CPU#3
Calibrating delay using timer specific routine.. 6000.48 BogoMIPS (lpj=12000974)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 3(4) -> Core 3
x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106
CPU3: AMD Phenom(tm) II X4 940 Processor stepping 02
Brought up 4 CPUs
Total of 4 processors activated (21949.99 BogoMIPS).
net_namespace: 660 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:12.0: set SATA to AHCI mode
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE6._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0d: mem resource (0xfed00000-0xfed000ff) overlaps 0000:00:00.0 BAR 3
(0xe0000000-0xffffffff), disabling
pnp 00:0d: mem resource (0xffff0000-0xffffffff) overlaps 0000:00:00.0 BAR 3
(0xe0000000-0xffffffff), disabling
pnp 00:0d: mem resource (0xfec00000-0xfec00fff) overlaps 0000:00:00.0 BAR 3
(0xe0000000-0xffffffff), disabling
pnp 00:0d: mem resource (0xfee00000-0xfee00fff) overlaps 0000:00:00.0 BAR 3
(0xe0000000-0xffffffff), disabling
pnp 00:0d: mem resource (0xfff80000-0xfffeffff) overlaps 0000:00:00.0 BAR 3
(0xe0000000-0xffffffff), disabling
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: Cannot allocate resource region 3 of device 0000:00:00.0
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
ACPI: RTC can wake from S4
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 1
system 00:01: ioport range 0x4100-0x411f has been reserved
system 00:01: ioport range 0x228-0x22f has been reserved
system 00:01: ioport range 0x40b-0x40b has been reserved
system 00:01: ioport range 0x4d6-0x4d6 has been reserved
system 00:01: ioport range 0xc00-0xc01 has been reserved
system 00:01: ioport range 0xc14-0xc14 has been reserved
system 00:01: ioport range 0xc50-0xc52 has been reserved
system 00:01: ioport range 0xc6c-0xc6d has been reserved
system 00:01: ioport range 0xc6f-0xc6f has been reserved
system 00:01: ioport range 0xcd0-0xcd1 has been reserved
system 00:01: ioport range 0xcd2-0xcd3 has been reserved
system 00:01: ioport range 0xcd4-0xcdf has been reserved
system 00:01: ioport range 0x4000-0x40fe has been reserved
system 00:01: ioport range 0x4210-0x4217 has been reserved
system 00:01: ioport range 0xb10-0xb1f has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x220-0x225 has been reserved
system 00:0d: iomem range 0xf0000-0xfffff could not be reserved
system 00:0d: iomem range 0x0-0x1fffff could not be reserved
system 00:0d: iomem range 0xbffe0000-0xbfffffff could not be reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0x100000-0xbffdffff could not be reserved
PCI: Bridge: 0000:00:02.0
IO window: d000-dfff
MEM window: 0xf8000000-0xfbffffff
PREFETCH window: 0x00000000c0000000-0x00000000dfffffff
PCI: Bridge: 0000:00:04.0
IO window: c000-cfff
MEM window: 0xfdc00000-0xfdcfffff
PREFETCH window: 0x00000000fdb00000-0x00000000fdbfffff
PCI: Bridge: 0000:00:06.0
IO window: b000-bfff
MEM window: 0xfda00000-0xfdafffff
PREFETCH window: 0x00000000fdf00000-0x00000000fdffffff
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: 0xfde00000-0xfdefffff
PREFETCH window: 0x00000000fdd00000-0x00000000fddfffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: 0xfd900000-0xfd9fffff
PREFETCH window: 0x00000000fd800000-0x00000000fd8fffff
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:04.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:07.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 10039k freed
audit: initializing netlink socket (disabled)
type=2000 audit(1232684854.924:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
bigphysarea: Allocated 16384 pages at 0xc3038000.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1462
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
vesafb: framebuffer at 0xf9000000, mapped to 0xf4880000, using 3072k, total 14336k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:b0a0
vesafb: pmi: set display start = c00cb103, set palette = c00cb15e
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0
3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
logips2pp: Detected unknown logitech mouse model 11
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
Using IPI No-Shortcut mode
Freeing unused kernel memory: 216k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
ACPI: PCI Interrupt 0000:03:00.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:03:00.1 to 64
scsi0 : pata_jmicron
scsi1 : pata_jmicron
ata1: PATA max UDMA/100 cmd 0xbf00 ctl 0xbe00 bmdma 0xbb00 irq 19
ata2: PATA max UDMA/100 cmd 0xbd00 ctl 0xbc00 bmdma 0xbb08 irq 19
ahci 0000:00:12.0: version 3.0
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
ata3: SATA max UDMA/133 abar m1024@...e02f000 port 0xfe02f100 irq 22
ata4: SATA max UDMA/133 abar m1024@...e02f000 port 0xfe02f180 irq 22
ata5: SATA max UDMA/133 abar m1024@...e02f000 port 0xfe02f200 irq 22
ata6: SATA max UDMA/133 abar m1024@...e02f000 port 0xfe02f280 irq 22
ata3: softreset failed (device not ready)
ata3: failed due to HW bug, retry pmp=0
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
ata3.00: configured for UDMA/133
ata4: softreset failed (device not ready)
ata4: failed due to HW bug, retry pmp=0
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
ata4.00: configured for UDMA/133
ata5: softreset failed (device not ready)
ata5: failed due to HW bug, retry pmp=0
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133
ata5.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
ata5.00: configured for UDMA/133
ata6: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:03:00.0 to 64
scsi6 : ahci
scsi7 : ahci
ata7: SATA max UDMA/133 abar m8192@...dafe000 port 0xfdafe100 irq 18
ata8: SATA max UDMA/133 abar m8192@...dafe000 port 0xfdafe180 irq 18
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SB600_PATA: IDE controller (0x1002:0x438c rev 0x00) at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf900-0xf907
Probing IDE interface ide0...
hda: ST3120023A, ATA DISK drive
hdb: TSSTcorpCD/DVDW TS-H552B, ATAPI CD/DVD-ROM drive
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/33 mode selected
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 21 (level, low) -> IRQ 21
scsi8 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 2930CU SCSI adapter>
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
scsi 8:0:0:0: Direct-Access SEAGATE ST15150N 5052 PQ: 0 ANSI: 2
scsi8:A:0:0: Tagged Queuing enabled. Depth 32
target8:0:0: Beginning Domain Validation
target8:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
target8:0:0: Domain Validation skipping write tests
target8:0:0: Ending Domain Validation
scsi 8:0:2:0: Sequential-Access ARCHIVE Python 01931-XXX 5.63 PQ: 0 ANSI: 2
target8:0:2: Beginning Domain Validation
target8:0:2: FAST-10 SCSI 7.8 MB/s ST (128 ns, offset 15)
target8:0:2: Domain Validation skipping write tests
target8:0:2: Ending Domain Validation
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:04:00.0 to 64
sky2 0000:04:00.0: v1.21 addr 0xfdefc000 irq 19 Yukon-EC Ultra (0xb4) rev 5
sky2 eth0: addr 00:e0:4d:7a:8c:ee
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda:<6>usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
sda1 sda2 sda3 <<6>ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus
number 1
sda5<6>ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
sda6<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
sda7<6>ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
sda8<6>hub 1-0:1.0: USB hub found
sda9<6>hub 1-0:1.0: 10 ports detected
sda10 >
sd 2:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7<6>usb usb1: New USB device found,
idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
sdb8<6>usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.26.8-lcrs ehci_hcd
usb usb1: SerialNumber: 0000:00:13.5
sdb9<6>ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
sdb10 >
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sdc: sdc1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 4:0:0:0: [sdc] Attached SCSI disk
sd 8:0:0:0: [sdd] Unsupported sector size 768.
sd 8:0:0:0: [sdd] 0 512-byte hardware sectors (0 MB)
sd 8:0:0:0: [sdd] Write Protect is off
sd 8:0:0:0: [sdd] Mode Sense: ab 00 10 08
sd 8:0:0:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA
sd 8:0:0:0: [sdd] Attached SCSI disk
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.26.8-lcrs ohci_hcd
usb usb2: SerialNumber: 0000:00:13.0
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
usb 1-1: new high speed USB device using ehci_hcd and address 2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: New USB device found, idVendor=03f0, idProduct=5111
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Photosmart 3200 series
usb 1-1: Manufacturer: HP
usb 1-1: SerialNumber: MY5B98310Z045K
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.26.8-lcrs ohci_hcd
usb usb3: SerialNumber: 0000:00:13.1
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.26.8-lcrs ohci_hcd
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb usb4: SerialNumber: 0000:00:13.2
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.26.8-lcrs ohci_hcd
usb usb5: SerialNumber: 0000:00:13.3
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
usb 1-2: New USB device found, idVendor=0424, idProduct=2504
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: OHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.26.8-lcrs ohci_hcd
usb usb6: SerialNumber: 0000:00:13.4
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: Attached scsi generic sg1 type 0
sd 4:0:0:0: Attached scsi generic sg2 type 0
sd 8:0:0:0: Attached scsi generic sg3 type 0
scsi 8:0:2:0: Attached scsi generic sg4 type 1
hda: max request size: 128KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1
Linux agpgart interface v0.103
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5111
usbcore: registered new interface driver usblp
st: Version 20080224, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
st 8:0:2:0: Attached scsi tape st0
st 8:0:2:0: st0: try direct i/o: yes (alignment 4 B)
IT8718 SuperIO detected.
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
Initializing USB Mass Storage driver...
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
eth1: (PCI Express:2.5GB/s:Width x1) 00:1b:21:0f:09:1b
eth1: Intel(R) PRO/1000 Network Connection
eth1: MAC: 1, PHY: 4, PBA No: d50854-003
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
ppdev: user-space parallel port driver
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.1.1.1 2009/01/04 11:41:44 markh Exp $
Driver 'osst' needs updating - please use bus_type methods
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
nvidia: module license 'NVIDIA' taints kernel.
st0: Block limits 1 - 16777215 bytes.
ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
ALSA sound/pci/hda/hda_codec.c:3021: autoconfig: line_outs=4
(0x14/0x15/0x16/0x17/0x0)
ALSA sound/pci/hda/hda_codec.c:3025: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3029: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3030: mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3038: inputs: mic=0x18, fmic=0x19, line=0x1a,
fline=0x0, cd=0x0, aux=0x0
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 177.82 Tue Nov 4 13:35:57 PST 2008
Adding 8393952k swap on /dev/sda2. Priority:-1 extents:1 across:8393952k
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@...hat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
scsi 9:0:0:0: Direct-Access HP Photosmart 3210 1.00 PQ: 0 ANSI: 2
sd 9:0:0:0: [sde] Attached SCSI removable disk
fuse init (API version 7.9)
sd 9:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
sky2 eth0: enabling interface
ADDRCONF(NETDEV_UP): eth0: link is not ready
ADDRCONF(NETDEV_UP): eth1: link is not ready
sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
warning: `ntpd' uses deprecated v2 capabilities in a way that may be insecure.
hda-intel: Invalid position buffer, using LPIB read method instead.
NET: Registered protocol family 4
NET: Registered protocol family 3
NET: Registered protocol family 5
Regards
Mark
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists