BIOS EBDA/lowmem at: 0009f800/0009f800 Linux version 2.6.28-rc9c3 (greearb@fs2.candelatech.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #17 PREEMPT Wed Feb 4 23:06:01 PST 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003eef0000 (usable) BIOS-e820: 000000003eef0000 - 000000003ef00000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) DMI 2.3 present. Phoenix BIOS detected: BIOS may corrupt low RAM, working it around. last_pfn = 0x3eef0 max_arch_pfn = 0x100000 Warning only 895MB will be used. Use a HIGHMEM enabled kernel. kernel direct mapping tables up to 37faa000 @ 10000-16000 RAMDISK: 37d20000 - 37fefc35 Allocated new RAMDISK: 0055d000 - 0082cc35 Move RAMDISK from 0000000037d20000 - 0000000037fefc34 to 0055d000 - 0082cc34 ACPI Error (tbxfroot-0218): A valid RSDP was not found [20080926] 895MB LOWMEM available. mapped low ram: 0 - 37faa000 low ram: 00000000 - 37faa000 bootmap 00012000 - 00018ff8 (7 early reservations) ==> bootmem [0000000000 - 0037faa000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000100000 - 0000559308] TEXT DATA BSS ==> [0000100000 - 0000559308] #2 [000055a000 - 000055d000] INIT_PG_TABLE ==> [000055a000 - 000055d000] #3 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] #4 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000] #5 [000055d000 - 000082cc35] NEW RAMDISK ==> [000055d000 - 000082cc35] #6 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000] found SMP MP-table at [c00f3520] 000f3520 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 Normal 0x00001000 -> 0x00037faa Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009f 0: 0x00000100 -> 0x00037faa On node 0 totalpages: 229177 free_area_init_node: node 0, pgdat c04b81c0, node_mem_map c1000200 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3951 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223434 pages, LIFO batch:31 Movable zone: 0 pages used for memmap ACPI: No APIC-table, disabling MPS No local APIC present or hardware disabled Allocating PCI resources starting at 40000000 (gap: 3ef00000:bfd00000) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227385 Kernel command line: ro root=LABEL=/ ide=nodma ide_core.nodma=0.1 ide_core.nodma=0.0 console=ttyS0,38400 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Fast TSC calibration using PIT Detected 997.603 MHz processor. Console: colour VGA+ 80x25 console [ttyS0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 901232k/917160k available (2535k kernel code, 15364k reserved, 1312k data, 308k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffac000 - 0xfffff000 ( 332 kB) vmalloc : 0xf87aa000 - 0xfffaa000 ( 120 MB) lowmem : 0xc0000000 - 0xf7faa000 ( 895 MB) .init : 0xc04c6000 - 0xc0513000 ( 308 kB) .data : 0xc0379ed6 - 0xc04c205c (1312 kB) .text : 0xc0100000 - 0xc0379ed6 (2535 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. Calibrating delay loop (skipped), value calculated using timer frequency.. 1995.20 BogoMIPS (lpj=997603) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 128K (64 bytes/line) CPU: Centaur VIA Esther processor 1000MHz stepping 09 Checking 'hlt' instruction... OK. Freeing SMP alternatives: 0k freed ACPI: Core revision 20080926 ACPI Exception (tbxface-0627): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20080926] ACPI: Unable to load the System Description Tables ------------[ cut here ]------------ WARNING: at /home/greearb/git/linux-2.6.linus/kernel/time/clockevents.c:46 clockevent_delta2ns+0xaf/0xc0() Modules linked in: Pid: 1, comm: swapper Not tainted 2.6.28-rc9c3 #17 Call Trace: [] warn_on_slowpath+0x5f/0x90 [] lapic_cal_handler+0x8d/0xe0 [] _spin_lock_irqsave+0x20/0x30 [] _spin_unlock_irqrestore+0x14/0x30 [] handle_level_irq+0x9b/0xe0 [] irq_exit+0x4d/0x80 [] do_IRQ+0x55/0xb0 [] tick_handle_periodic+0x0/0x70 [] common_interrupt+0x23/0x30 [] tick_handle_periodic+0x0/0x70 [] clockevent_delta2ns+0xaf/0xc0 [] setup_boot_APIC_clock+0x1e9/0x580 [] schedule_tail+0xf/0x40 [] setup_apic_nmi_watchdog+0x15/0x60 [] APIC_init_uniprocessor+0x8d/0x100 [] kernel_init+0x47/0xe0 [] kernel_init+0x0/0xe0 [] kernel_thread_helper+0x7/0x10 ---[ end trace 4eaa2a86a8e2da22 ]--- APIC frequency too slow, disabling apic timer net_namespace: 740 bytes NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf9f30, last bus=1 PCI: Using configuration type 1 for base access ACPI: Interpreter disabled. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) pci 0000:00:00.0: reg 10 32bit mmio: [0xe8000000-0xefffffff] pci 0000:00:01.0: supports D1 pci 0000:00:08.0: reg 10 io port: [0xd000-0xd0ff] pci 0000:00:08.0: reg 14 32bit mmio: [0xf6000000-0xf60000ff] pci 0000:00:08.0: supports D1 D2 pci 0000:00:08.0: PME# supported from D1 D2 D3hot D3cold pci 0000:00:08.0: PME# disabled pci 0000:00:09.0: reg 10 io port: [0xd400-0xd4ff] pci 0000:00:09.0: reg 14 32bit mmio: [0xf6001000-0xf60010ff] pci 0000:00:09.0: supports D1 D2 pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold pci 0000:00:09.0: PME# disabled pci 0000:00:0a.0: reg 10 io port: [0xd800-0xd8ff] pci 0000:00:0a.0: reg 14 32bit mmio: [0xf6002000-0xf60020ff] pci 0000:00:0a.0: supports D1 D2 pci 0000:00:0a.0: PME# supported from D1 D2 D3hot D3cold pci 0000:00:0a.0: PME# disabled pci 0000:00:0b.0: reg 10 io port: [0xdc00-0xdcff] pci 0000:00:0b.0: reg 14 32bit mmio: [0xf6003000-0xf60030ff] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D1 D2 D3hot D3cold pci 0000:00:0b.0: PME# disabled pci 0000:00:0f.0: reg 10 io port: [0xe800-0xe807] pci 0000:00:0f.0: reg 14 io port: [0xe400-0xe403] pci 0000:00:0f.0: reg 18 io port: [0xe500-0xe507] pci 0000:00:0f.0: reg 1c io port: [0xe600-0xe603] pci 0000:00:0f.0: reg 20 io port: [0xe700-0xe70f] pci 0000:00:0f.0: reg 24 io port: [0xe000-0xe0ff] pci 0000:00:0f.1: reg 20 io port: [0xe900-0xe90f] pci 0000:00:10.0: reg 20 io port: [0xea00-0xea1f] pci 0000:00:10.0: supports D1 D2 pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.0: PME# disabled pci 0000:00:10.1: reg 20 io port: [0x00-0x1f] pci 0000:00:10.1: supports D1 D2 pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.1: PME# disabled pci 0000:00:10.2: reg 20 io port: [0x00-0x1f] pci 0000:00:10.2: supports D1 D2 pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.2: PME# disabled pci 0000:00:10.3: reg 20 io port: [0x00-0x1f] pci 0000:00:10.3: supports D1 D2 pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.3: PME# disabled pci 0000:00:10.4: reg 10 32bit mmio: [0xf6004000-0xf60040ff] pci 0000:00:10.4: supports D1 D2 pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.4: PME# disabled HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:01:00.0: reg 10 32bit mmio: [0xf0000000-0xf3ffffff] pci 0000:01:00.0: reg 14 32bit mmio: [0xf4000000-0xf4ffffff] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] pci 0000:01:00.0: supports D1 D2 pci 0000:00:01.0: bridge 32bit mmio: [0xf4000000-0xf5ffffff] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf0000000-0xf3ffffff] pci 0000:00:11.0: VIA IRQ router [1106:3227] PCI: setting IRQ 10 as level-triggered pci 0000:00:0f.1: found PCI INT A -> IRQ 10 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:08.0 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:10.0 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:10.1 PCI: setting IRQ 11 as level-triggered pci 0000:00:10.2: found PCI INT B -> IRQ 11 pci 0000:00:10.2: sharing IRQ 11 with 0000:00:09.0 pci 0000:00:10.2: sharing IRQ 11 with 0000:00:0f.0 pci 0000:00:10.2: sharing IRQ 11 with 0000:00:10.3 pnp: PnP ACPI: disabled pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: disabled pci 0000:00:01.0: MEM window: 0xf4000000-0xf5ffffff pci 0000:00:01.0: PREFETCH window: 0x000000f0000000-0x000000f3ffffff pci 0000:00:01.0: setting latency timer to 64 bus: 00 index 0 io port: [0x00-0xffff] bus: 00 index 1 mmio: [0x000000-0xffffffff] bus: 01 index 0 mmio: [0x0-0x0] bus: 01 index 1 mmio: [0xf4000000-0xf5ffffff] bus: 01 index 2 mmio: [0xf0000000-0xf3ffffff] bus: 01 index 3 mmio: [0x0-0x0] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 8, 1310720 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 2879k freed platform rtc_cmos: registered platform RTC device (no PNP device found) apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) audit: initializing netlink socket (disabled) type=2000 audit(1233817727.201:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1766 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: VIA PCI bridge detected.Disabling DAC. Clocksource tsc unstable (delta = 155908557 ns) pci 0000:00:10.4: EHCI: BIOS handoff failed (BIOS bug?) 01010001 pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message pci 0000:01:00.0: Boot video device Real Time Clock Driver v1.12ac VIA RNG detected Linux agpgart interface v0.103 agpgart: Detected VIA VT3314 chipset agpgart-via 0000:00:00.0: AGP aperture is 128M @ 0xe8000000 [drm] Initialized drm 1.1.0 20060810 Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A brd: module loaded Uniform Multi-Platform E-IDE driver via82cxxx 0000:00:0f.1: VIA vt8237 (rev 00) IDE UDMA133 via82cxxx 0000:00:0f.1: IDE controller (0x1106:0x0571 rev 0x06) pci 0000:00:0f.1: found PCI INT A -> IRQ 10 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:08.0 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:10.0 pci 0000:00:0f.1: sharing IRQ 10 with 0000:00:10.1 pci 0000:00:0f.1: VIA VLink IRQ fixup, from 255 to 10 via82cxxx 0000:00:0f.1: not 100% native mode: will probe irqs later ide: disallowing DMA for hda ide: disallowing DMA for hdb ide0: BM-DMA at 0xe900-0xe907 ide1: BM-DMA at 0xe908-0xe90f Probing IDE interface ide0... hdb: , ATA DISK drive hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO2 hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO2 Probing IDE interface ide1... ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports ide-gd driver 1.18 hdb: max request size: 128KiB hdb: 3915072 sectors (2004 MB) w/1KiB Cache, CHS=3884/16/63 hdb: hdb1 ide-cd driver 5.00 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 IO APIC resources could be not be allocated. Using IPI Shortcut mode Freeing unused kernel memory: 308k freed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: setting IRQ 9 as level-triggered ehci_hcd 0000:00:10.4: found PCI INT C -> IRQ 9 ehci_hcd 0000:00:10.4: sharing IRQ 9 with 0000:00:0a.0 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: irq 9, io mem 0xf6004000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:10.0: found PCI INT A -> IRQ 10 uhci_hcd 0000:00:10.0: sharing IRQ 10 with 0000:00:08.0 uhci_hcd 0000:00:10.0: sharing IRQ 10 with 0000:00:0f.1 uhci_hcd 0000:00:10.0: sharing IRQ 10 with 0000:00:10.1 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 10, io base 0x0000ea00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: enabling device (0000 -> 0001) uhci_hcd 0000:00:10.1: found PCI INT A -> IRQ 10 uhci_hcd 0000:00:10.1: sharing IRQ 10 with 0000:00:08.0 uhci_hcd 0000:00:10.1: sharing IRQ 10 with 0000:00:0f.1 uhci_hcd 0000:00:10.1: sharing IRQ 10 with 0000:00:10.0 uhci_hcd 0000:00:10.1: VIA VLink IRQ fixup, from 0 to 10 uhci_hcd 0000:00:10.1: UHCI Host Controller input: ImExPS/2 Generic Explorer Mouse as /class/input/input0 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 10, io base 0x00001000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: enabling device (0000 -> 0001) uhci_hcd 0000:00:10.2: found PCI INT B -> IRQ 11 uhci_hcd 0000:00:10.2: sharing IRQ 11 with 0000:00:09.0 uhci_hcd 0000:00:10.2: sharing IRQ 11 with 0000:00:0f.0 uhci_hcd 0000:00:10.2: sharing IRQ 11 with 0000:00:10.3 uhci_hcd 0000:00:10.2: VIA VLink IRQ fixup, from 0 to 11 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 input: AT Translated Set 2 keyboard as /class/input/input1 uhci_hcd 0000:00:10.2: irq 11, io base 0x00001020 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:10.3: enabling device (0000 -> 0001) uhci_hcd 0000:00:10.3: found PCI INT B -> IRQ 11 uhci_hcd 0000:00:10.3: sharing IRQ 11 with 0000:00:09.0 uhci_hcd 0000:00:10.3: sharing IRQ 11 with 0000:00:0f.0 uhci_hcd 0000:00:10.3: sharing IRQ 11 with 0000:00:10.2 uhci_hcd 0000:00:10.3: VIA VLink IRQ fixup, from 0 to 11 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 11, io base 0x00001040 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected SCSI subsystem initialized Driver 'sd' needs updating - please use bus_type methods Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. 8139too Fast Ethernet driver 0.9.28 8139too 0000:00:08.0: found PCI INT A -> IRQ 10 8139too 0000:00:08.0: sharing IRQ 10 with 0000:00:0f.1 8139too 0000:00:08.0: sharing IRQ 10 with 0000:00:10.0 8139too 0000:00:08.0: sharing IRQ 10 with 0000:00:10.1 eth0: RealTek RTL8139 at 0xf88be000, 00:03:2d:0c:d0:23, IRQ 10 eth0: Identified 8139 chip type 'RTL-8100B/8139D' 8139too 0000:00:09.0: found PCI INT A -> IRQ 11 8139too 0000:00:09.0: sharing IRQ 11 with 0000:00:0f.0 8139too 0000:00:09.0: sharing IRQ 11 with 0000:00:10.2 8139too 0000:00:09.0: sharing IRQ 11 with 0000:00:10.3 eth1: RealTek RTL8139 at 0xf87be000, 00:03:2d:0c:d0:22, IRQ 11 eth1: Identified 8139 chip type 'RTL-8100B/8139D' 8139too 0000:00:0a.0: found PCI INT A -> IRQ 9 8139too 0000:00:0a.0: sharing IRQ 9 with 0000:00:10.4 eth2: RealTek RTL8139 at 0xf87c2000, 00:03:2d:0c:d0:21, IRQ 9 eth2: Identified 8139 chip type 'RTL-8100B/8139D' PCI: setting IRQ 5 as level-triggered 8139too 0000:00:0b.0: found PCI INT A -> IRQ 5 eth3: RealTek RTL8139 at 0xf87c6000, 00:03:2d:0c:d0:20, IRQ 5 eth3: Identified 8139 chip type 'RTL-8100B/8139D' 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) input: PC Speaker as /class/input/input2 EXT3 FS on hdb1, internal journal warning: process `kudzu' used the deprecated sysctl system call with 1.23. NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth3: link up, 100Mbps, full-duplex, lpa 0xC5E1 RPC: Registered udp transport module. RPC: Registered tcp transport module. warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use) eth3: no IPv6 routers present pktgen v2.70: Packet Generator for packet performance testing. wanlink: version magic '2.6.29-rc3c3 preempt mod_unload VIAC3-2 ' should be '2.6.28-rc9c3 preempt mod_unload VIAC3-2 ' eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 eth2: link down ADDRCONF(NETDEV_UP): eth2: link is not ready eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 eth1: link up, 100Mbps, full-duplex, lpa 0x41E1 ip_tables: (C) 2000-2006 Netfilter Core Team eth0: no IPv6 routers present