Initializing cgroup subsys cpu Linux version 2.6.29-rc5 (root@brouette) (gcc version 4.3.3 (Debian 4.3.3-3) ) #1 SMP Sun Feb 15 11:15:54 CET 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007ff74000 (usable) BIOS-e820: 000000007ff74000 - 000000007ff76000 (ACPI NVS) BIOS-e820: 000000007ff76000 - 000000007ff97000 (ACPI data) BIOS-e820: 000000007ff97000 - 0000000080000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fecf0000 - 00000000fecf1000 (reserved) BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) DMI 2.3 present. last_pfn = 0x7ff74 max_arch_pfn = 0x100000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 kernel direct mapping tables up to 377fe000 @ 7000-c000 ACPI: RSDP 000FEB90, 0014 (r0 DELL ) ACPI: RSDT 000FD1CA, 0034 (r1 DELL 8300 8 ASL 61) ACPI: FACP 000FD1FE, 0074 (r1 DELL 8300 8 ASL 61) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT FFFC6E75, 2426 (r1 DELL dt_ex 1000 MSFT 100000D) ACPI: FACS 7FF74000, 0040 ACPI: SSDT FFFC93D8, 00BA (r1 DELL st_ex 1000 MSFT 100000D) ACPI: APIC 000FD272, 006C (r1 DELL 8300 8 ASL 61) ACPI: BOOT 000FD2DE, 0028 (r1 DELL 8300 8 ASL 61) ACPI: Local APIC address 0xfee00000 1159MB HIGHMEM available. 887MB LOWMEM available. mapped low ram: 0 - 377fe000 low ram: 00000000 - 377fe000 bootmap 00008000 - 0000ef00 (8 early reservations) ==> bootmem [0000000000 - 00377fe000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 0000500640] TEXT DATA BSS ==> [0000100000 - 0000500640] #4 [0000501000 - 0000504000] INIT_PG_TABLE ==> [0000501000 - 0000504000] #5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] #7 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] found SMP MP-table at [c00fe710] 000fe710 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x000377fe HighMem 0x000377fe -> 0x0007ff74 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x000000a0 0: 0x00000100 -> 0x0007ff74 On node 0 totalpages: 524052 free_area_init_node: node 0, pgdat c044ed80, node_mem_map c1000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3968 pages, LIFO batch:0 Normal zone: 1744 pages used for memmap Normal zone: 221486 pages, LIFO batch:31 HighMem zone: 2319 pages used for memmap HighMem zone: 294503 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information 4 Processors exceeds NR_CPUS limit of 2 SMP: Allowing 2 CPUs, 0 hotplug CPUs nr_irqs_gsi: 24 Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000) NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Allocating 36864 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519957 Kernel command line: root=/dev/sdb2 ro vga=0x307 selinux=0 elevator=cfq video=vesafb:mtrr:3 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 Experimental hierarchical RCU implementation. Experimental hierarchical RCU init done. CPU 0 irqstacks, hard=c04ae000 soft=c04ac000 PID hash table entries: 4096 (order: 12, 16384 bytes) Fast TSC calibration using PIT Detected 2992.546 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 2073812k/2096592k available (2449k kernel code, 21420k reserved, 1034k data, 248k init, 1187288k highmem) virtual kernel memory layout: fixmap : 0xfff9f000 - 0xfffff000 ( 384 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB) lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB) .init : 0xc046b000 - 0xc04a9000 ( 248 kB) .data : 0xc0364487 - 0xc0466e40 (1034 kB) .text : 0xc0100000 - 0xc0364487 (2449 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 5985.09 BogoMIPS (lpj=2992546) Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled using mwait in idle threads. Checking 'hlt' instruction... OK. ACPI: Core revision 20081204 ftrace: converting mcount calls to 0f 1f 44 00 00 ftrace: allocating 13232 entries in 52 pages ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 CPU 1 irqstacks, hard=c04af000 soft=c04ad000 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5983.76 BogoMIPS (lpj=2991881) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs Total of 2 processors activated (11968.85 BogoMIPS). net_namespace: 504 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfbb30, last bus=2 PCI: Using configuration type 1 for base access bio: create slab at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:00.0: reg 10 32bit mmio: [0xe8000000-0xefffffff] pci 0000:00:1d.0: reg 20 io port: [0xff80-0xff9f] pci 0000:00:1d.1: reg 20 io port: [0xff60-0xff7f] pci 0000:00:1d.2: reg 20 io port: [0xff40-0xff5f] pci 0000:00:1d.3: reg 20 io port: [0xff20-0xff3f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xffa80800-0xffa80bff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH4 GPIO pci 0000:00:1f.1: reg 10 io port: [0x1f0-0x1f7] pci 0000:00:1f.1: reg 14 io port: [0x3f4-0x3f7] pci 0000:00:1f.1: reg 18 io port: [0x170-0x177] pci 0000:00:1f.1: reg 1c io port: [0x374-0x377] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf] pci 0000:00:1f.1: reg 24 32bit mmio: [0xfebffc00-0xfebfffff] pci 0000:00:1f.2: reg 10 io port: [0xfe00-0xfe07] pci 0000:00:1f.2: reg 14 io port: [0xfe10-0xfe13] pci 0000:00:1f.2: reg 18 io port: [0xfe20-0xfe27] pci 0000:00:1f.2: reg 1c io port: [0xfe30-0xfe33] pci 0000:00:1f.2: reg 20 io port: [0xfea0-0xfeaf] pci 0000:00:1f.3: reg 20 io port: [0xefe0-0xefff] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff] pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xf7ffffff] pci 0000:01:00.0: reg 30 32bit mmio: [0xfea00000-0xfea1ffff] pci 0000:00:01.0: bridge 32bit mmio: [0xfd000000-0xfeafffff] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf0000000-0xf7ffffff] pci 0000:02:00.0: reg 10 io port: [0xdf20-0xdf3f] pci 0000:02:00.0: supports D1 D2 pci 0000:02:00.1: reg 10 io port: [0xdf18-0xdf1f] pci 0000:02:00.1: supports D1 D2 pci 0000:02:08.0: reg 10 32bit mmio: [0xfcfff000-0xfcffffff] pci 0000:02:08.0: reg 14 io port: [0xdf40-0xdf7f] pci 0000:02:08.0: supports D1 D2 pci 0000:02:08.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:08.0: PME# disabled pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge io port: [0xd000-0xdfff] pci 0000:00:1e.0: bridge 32bit mmio: [0xfcf00000-0xfcffffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15) SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:07: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling pnp 00:07: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 7 (0x800-0x87f), disabling pnp: PnP ACPI: found 8 devices ACPI: ACPI bus type pnp unregistered system 00:00: iomem range 0x0-0x9ffff could not be reserved system 00:00: iomem range 0x100000-0xffffff could not be reserved system 00:00: iomem range 0x1000000-0x7ff73fff could not be reserved system 00:00: iomem range 0xc0000-0xfffff could not be reserved system 00:00: iomem range 0xfec00000-0xfec0ffff has been reserved system 00:00: iomem range 0xfee00000-0xfee0ffff has been reserved system 00:00: iomem range 0xfed20000-0xfed8ffff has been reserved system 00:00: iomem range 0xfecf0000-0xfecf0fff has been reserved system 00:00: iomem range 0xffb00000-0xffbfffff has been reserved system 00:00: iomem range 0xffc00000-0xffffffff has been reserved system 00:07: ioport range 0xc00-0xc7f has been reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: disabled pci 0000:00:01.0: MEM window: 0xfd000000-0xfeafffff pci 0000:00:01.0: PREFETCH window: 0x000000f0000000-0x000000f7ffffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02 pci 0000:00:1e.0: IO window: 0xd000-0xdfff pci 0000:00:1e.0: MEM window: 0xfcf00000-0xfcffffff pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] pci_bus 0000:01: resource 0 mem: [0x0-0x0] pci_bus 0000:01: resource 1 mem: [0xfd000000-0xfeafffff] pci_bus 0000:01: resource 2 mem: [0xf0000000-0xf7ffffff] pci_bus 0000:01: resource 3 mem: [0x0-0x0] pci_bus 0000:02: resource 0 io: [0xd000-0xdfff] pci_bus 0000:02: resource 1 mem: [0xfcf00000-0xfcffffff] pci_bus 0000:02: resource 2 mem: [0x0-0x0] pci_bus 0000:02: resource 3 io: [0x00-0xffff] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 Simple Boot Flag value 0x87 read from CMOS RAM was invalid Simple Boot Flag at 0x7a set to 0x1 Machine check exception polling timer started. highmem bounce pool size: 64 pages SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 1733 io scheduler noop registered io scheduler anticipatory registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device pci 0000:02:08.0: Firmware left e100 interrupts enabled; disabling vesafb: framebuffer at 0xf0000000, mapped to 0xf8080000, using 2560k, total 131072k vesafb: mode is 1280x1024x8, linelength=1280, pages=1 vesafb: protected mode interface info at c000:f080 vesafb: pmi: set display start = c00cf0b6, set palette = c00cf120 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Console: switching to colour frame buffer device 160x64 fb0: VESA VGA frame buffer device input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 ACPI: Power Button (CM) [VBTN] processor ACPI_CPU:00: registered as cooling_device0 processor ACPI_CPU:01: registered as cooling_device1 Real Time Clock Driver v1.12b e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI e100: Copyright(c) 1999-2006 Intel Corporation e100 0000:02:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 e100 0000:02:08.0: PME# disabled e100: eth0: e100_probe: addr 0xfcfff000, irq 20, MAC addr 00:0c:f1:b6:ba:54 Driver 'sd' needs updating - please use bus_type methods ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata1: port disabled. ignoring. ata2.00: ATAPI: SAMSUNG DVD-ROM SD-616T, F310, max UDMA/33 ata2.01: ATAPI: SAMSUNG CD-R/RW SW-252S, R901, max UDMA/33 ata2.00: configured for UDMA/33 ata2.01: configured for UDMA/33 scsi 1:0:0:0: CD-ROM SAMSUNG DVD-ROM SD-616T F310 PQ: 0 ANSI: 5 scsi 1:0:0:0: Attached scsi generic sg0 type 5 scsi 1:0:1:0: CD-ROM SAMSUNG CD-R/RW SW-252S R901 PQ: 0 ANSI: 5 scsi 1:0:1:0: Attached scsi generic sg1 type 5 ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] ata_piix 0000:00:1f.2: setting latency timer to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0xfe00 ctl 0xfe10 bmdma 0xfea0 irq 18 ata4: SATA max UDMA/133 cmd 0xfe20 ctl 0xfe30 bmdma 0xfea8 irq 18 ata3.00: ATA-6: WDC WD740GD-75FLA0, 21.08U21, max UDMA/133 ata3.00: 144531250 sectors, multi 8: LBA48 ata3.00: applying bridge limits ata3.00: configured for UDMA/100 scsi 2:0:0:0: Direct-Access ATA WDC WD740GD-75FL 21.0 PQ: 0 ANSI: 5 sd 2:0:0:0: [sda] 144531250 512-byte hardware sectors: (74.0 GB/68.9 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sda] 144531250 512-byte hardware sectors: (74.0 GB/68.9 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 > sd 2:0:0:0: [sda] Attached SCSI disk sd 2:0:0:0: Attached scsi generic sg2 type 0 Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ata4.00: ATA-6: WDC WD740GD-75FLA0, 21.08U21, max UDMA/133 ata4.00: 144531250 sectors, multi 8: LBA48 ata4.00: applying bridge limits ata4.00: configured for UDMA/100 scsi 3:0:0:0: Direct-Access ATA WDC WD740GD-75FL 21.0 PQ: 0 ANSI: 5 sd 3:0:0:0: [sdb] 144531250 512-byte hardware sectors: (74.0 GB/68.9 GiB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdb] 144531250 512-byte hardware sectors: (74.0 GB/68.9 GiB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 > sd 3:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: Attached scsi generic sg3 type 0 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu Advanced Linux Sound Architecture Driver Version 1.0.18a. EMU10K1_Audigy 0000:02:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 Control name 'Sigmatel Surround Phase Inversion Playback Switch' truncated to 'Sigmatel Surround Phase Inversion Playback ' ALSA device list: #0: SB Live! [Unknown] (rev.10, serial:0x80671102) at 0xdf20, irq 21 TCP cubic registered NET: Registered protocol family 17 Using IPI No-Shortcut mode kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly on device 8:18. Freeing unused kernel memory: 248k freed parport_pc 00:06: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA] usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000ff80 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000ff60 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ff20 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Driver 'sr' needs updating - please use bus_type methods sr0: scsi3-mmc drive: 1x/48x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after sr1: scsi3-mmc drive: 48x/16x writer cd/rw xa/form2 cdda tray sr 1:0:1:0: Attached scsi CD-ROM sr1 ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xffa80800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb5: configuration #1 chosen from 1 choice input: PC Speaker as /devices/platform/pcspkr/input/input2 hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected usb 1-2: new full speed USB device using uhci_hcd and address 2 Adding 1212896k swap on /dev/sdb7. Priority:-1 extents:1 across:1212896k usb 1-2: configuration #1 chosen from 1 choice usb 2-1: new low speed USB device using uhci_hcd and address 2 EXT3 FS on sdb2, internal journal usb 2-1: configuration #1 chosen from 1 choice usb 3-2: new low speed USB device using uhci_hcd and address 2 generic-usb 0003:056D:0002.0001: claimed by neither input, hiddev nor hidraw usb 3-2: configuration #1 chosen from 1 choice input: HID 05af:0310 as /devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.0/input/input3 generic-usb 0003:05AF:0310.0002: input: USB HID v1.10 Keyboard [HID 05af:0310] on usb-0000:00:1d.1-1/input0 input: HID 05af:0310 as /devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.1/input/input4 generic-usb 0003:05AF:0310.0003: input: USB HID v1.10 Device [HID 05af:0310] on usb-0000:00:1d.1-1/input1 input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.2/usb3/3-2/3-2:1.0/input/input5 generic-usb 0003:046D:C51B.0004: input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.2-2/input0 generic-usb 0003:046D:C51B.0005: claimed by neither input, hiddev nor hidraw usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver XFS mounting filesystem sdb5 Ending clean XFS mount for filesystem: sdb5 XFS mounting filesystem sdb6 Ending clean XFS mount for filesystem: sdb6 XFS mounting filesystem sdb8 Ending clean XFS mount for filesystem: sdb8 XFS mounting filesystem sda5 Ending clean XFS mount for filesystem: sda5 e100: eth0 NIC Link is Up 100 Mbps Full Duplex lp0: using parport0 (interrupt-driven). warning: `ntpd' uses 32-bit capabilities (legacy support in use) CPU 1 is now offline SMP alternatives: switching to UP code SMP alternatives: switching to SMP code CPU 1 irqstacks, hard=c04af000 soft=c04ad000 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5984.41 BogoMIPS (lpj=2992209) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Switched to high resolution mode on CPU 1 Warning: Processor Platform Limit event detected, but not handled. Consider compiling CPUfreq support into your kernel.