Linux version 2.6.29-rc5.SMP.K8-64-00122-g5955c7a-dirty (root@secdev) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #21 SMP Tue Feb 17 18:41:12 PST 2009 Command line: auto BOOT_IMAGE=test2 ro root=803 console=ttyS1,9600n8 console=tty1 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 0000000000093800 (usable) BIOS-e820: 0000000000093800 - 0000000000094c00 (reserved) BIOS-e820: 00000000000eadc0 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000dfff0000 (usable) BIOS-e820: 00000000dfff0000 - 00000000dfffe000 (ACPI data) BIOS-e820: 00000000dfffe000 - 00000000e0000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000820000000 (usable) DMI present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. last_pfn = 0x820000 max_arch_pfn = 0x100000000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 last_pfn = 0xdfff0 max_arch_pfn = 0x100000000 init_memory_mapping: 0000000000000000-00000000dfff0000 0000000000 - 00dfe00000 page 2M 00dfe00000 - 00dfff0000 page 4k kernel direct mapping tables up to dfff0000 @ 10000-16000 last_map_addr: dfff0000 end: dfff0000 init_memory_mapping: 0000000100000000-0000000820000000 0100000000 - 0820000000 page 2M kernel direct mapping tables up to 820000000 @ 14000-36000 last_map_addr: 820000000 end: 820000000 ACPI: RSDP 000F9440, 0014 (r0 ACPIAM) ACPI: RSDT DFFF0000, 0034 (r1 A M I OEMRSDT 6000714 MSFT 97) ACPI: FACP DFFF0200, 0084 (r2 A M I OEMFACP 6000714 MSFT 97) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT DFFF0440, 5218 (r1 WTF4V WTF4V034 34 INTL 2002026) ACPI: FACS DFFFE000, 0040 ACPI: APIC DFFF0390, 00B0 (r1 A M I OEMAPIC 6000714 MSFT 97) ACPI: OEMB DFFFE040, 0063 (r1 A M I AMI_OEM 6000714 MSFT 97) ACPI: SRAT DFFF5660, 01A0 (r1 AMD HAMMER 1 AMD 1) ACPI: Local APIC address 0xfee00000 SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 0 -> APIC 1 -> Node 0 SRAT: PXM 1 -> APIC 2 -> Node 1 SRAT: PXM 1 -> APIC 3 -> Node 1 SRAT: PXM 2 -> APIC 4 -> Node 2 SRAT: PXM 2 -> APIC 5 -> Node 2 SRAT: PXM 3 -> APIC 6 -> Node 3 SRAT: PXM 3 -> APIC 7 -> Node 3 SRAT: Node 0 PXM 0 0-a0000 SRAT: Node 0 PXM 0 100000-e0000000 SRAT: Node 0 PXM 0 100000000-220000000 SRAT: Node 1 PXM 1 220000000-420000000 SRAT: Node 2 PXM 2 420000000-620000000 SRAT: Node 3 PXM 3 620000000-820000000 NUMA: Allocated memnodemap from 31000 - 41440 NUMA: Using 20 for the hash shift. Bootmem setup node 0 0000000000000000-0000000220000000 NODE_DATA [0000000000041440 - 000000000004343f] bootmap [0000000000044000 - 0000000000087fff] pages 44 (7 early reservations) ==> bootmem [0000000000 - 0220000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] #2 [0000200000 - 0000975dc4] TEXT DATA BSS ==> [0000200000 - 0000975dc4] #3 [0000093c00 - 0000100000] BIOS reserved ==> [0000093c00 - 0000100000] #4 [0000010000 - 0000014000] PGTABLE ==> [0000010000 - 0000014000] #5 [0000014000 - 0000031000] PGTABLE ==> [0000014000 - 0000031000] #6 [0000031000 - 0000041440] MEMNODEMAP ==> [0000031000 - 0000041440] Bootmem setup node 1 0000000220000000-0000000420000000 NODE_DATA [0000000220000000 - 0000000220001fff] bootmap [0000000220002000 - 0000000220041fff] pages 40 (7 early reservations) ==> bootmem [0220000000 - 0420000000] #0 [0000000000 - 0000001000] BIOS data page #1 [0000006000 - 0000008000] TRAMPOLINE #2 [0000200000 - 0000975dc4] TEXT DATA BSS #3 [0000093c00 - 0000100000] BIOS reserved #4 [0000010000 - 0000014000] PGTABLE #5 [0000014000 - 0000031000] PGTABLE #6 [0000031000 - 0000041440] MEMNODEMAP Bootmem setup node 2 0000000420000000-0000000620000000 NODE_DATA [0000000420000000 - 0000000420001fff] bootmap [0000000420002000 - 0000000420041fff] pages 40 (7 early reservations) ==> bootmem [0420000000 - 0620000000] #0 [0000000000 - 0000001000] BIOS data page #1 [0000006000 - 0000008000] TRAMPOLINE #2 [0000200000 - 0000975dc4] TEXT DATA BSS #3 [0000093c00 - 0000100000] BIOS reserved #4 [0000010000 - 0000014000] PGTABLE #5 [0000014000 - 0000031000] PGTABLE #6 [0000031000 - 0000041440] MEMNODEMAP Bootmem setup node 3 0000000620000000-0000000820000000 NODE_DATA [0000000620000000 - 0000000620001fff] bootmap [0000000620002000 - 0000000620041fff] pages 40 (7 early reservations) ==> bootmem [0620000000 - 0820000000] #0 [0000000000 - 0000001000] BIOS data page #1 [0000006000 - 0000008000] TRAMPOLINE #2 [0000200000 - 0000975dc4] TEXT DATA BSS #3 [0000093c00 - 0000100000] BIOS reserved #4 [0000010000 - 0000014000] PGTABLE #5 [0000014000 - 0000031000] PGTABLE #6 [0000031000 - 0000041440] MEMNODEMAP found SMP MP-table at [ffff8800000ff780] 000ff780 [ffffe20007700000-ffffe200077fffff] potential offnode page_structs [ffffe20000000000-ffffe200077fffff] PMD -> [ffff880028200000-ffff88002f3fffff] on node 0 [ffffe2000e700000-ffffe2000e7fffff] potential offnode page_structs [ffffe20007800000-ffffe2000e7fffff] PMD -> [ffff880220200000-ffff8802271fffff] on node 1 [ffffe20015700000-ffffe200157fffff] potential offnode page_structs [ffffe2000e800000-ffffe200157fffff] PMD -> [ffff880420200000-ffff8804271fffff] on node 2 [ffffe20015800000-ffffe2001c7fffff] PMD -> [ffff880620200000-ffff8806271fffff] on node 3 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 DMA32 0x00001000 -> 0x00100000 Normal 0x00100000 -> 0x00820000 Movable zone start PFN for each node early_node_map[6] active PFN ranges 0: 0x00000010 -> 0x00000093 0: 0x00000100 -> 0x000dfff0 0: 0x00100000 -> 0x00220000 1: 0x00220000 -> 0x00420000 2: 0x00420000 -> 0x00620000 3: 0x00620000 -> 0x00820000 On node 0 totalpages: 2097011 DMA zone: 56 pages used for memmap DMA zone: 2071 pages reserved DMA zone: 1844 pages, LIFO batch:0 DMA32 zone: 14280 pages used for memmap DMA32 zone: 899112 pages, LIFO batch:31 Normal zone: 16128 pages used for memmap Normal zone: 1163520 pages, LIFO batch:31 On node 1 totalpages: 2097152 Normal zone: 28672 pages used for memmap Normal zone: 2068480 pages, LIFO batch:31 On node 2 totalpages: 2097152 Normal zone: 28672 pages used for memmap Normal zone: 2068480 pages, LIFO batch:31 On node 3 totalpages: 2097152 Normal zone: 28672 pages used for memmap Normal zone: 2068480 pages, LIFO batch:31 Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override Detected use of extended apic ids on hypertransport bus Detected use of extended apic ids on hypertransport bus Detected use of extended apic ids on hypertransport bus Detected use of extended apic ids on hypertransport bus ACPI: PM-Timer IO Port: 0x2008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x04] enabled) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x05] enabled) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x06] enabled) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x09] address[0xfebfc000] gsi_base[24]) IOAPIC[1]: apic_id 9, version 0, address 0xfebfc000, GSI 24-47 ACPI: IOAPIC (id[0x0a] address[0xfebfe000] gsi_base[72]) IOAPIC[2]: apic_id 10, version 0, address 0xfebfe000, GSI 72-78 ACPI: IOAPIC (id[0x0b] address[0xfebff000] gsi_base[79]) IOAPIC[3]: apic_id 11, version 0, address 0xfebff000, GSI 79-85 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information SMP: Allowing 8 CPUs, 0 hotplug CPUs nr_irqs_gsi: 86 Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000) NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:4 PERCPU: Allocating 40960 bytes of per cpu data Built 4 zonelists in Zone order, mobility grouping on. Total pages: 8269916 Policy zone: Normal Kernel command line: auto BOOT_IMAGE=test2 ro root=803 console=ttyS1,9600n8 console=tty1 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Fast TSC calibration using PIT Detected 2814.492 MHz processor. spurious 8259A interrupt: IRQ7. Console: colour VGA+ 80x25 console [tty1] enabled console [ttyS1] enabled Checking aperture... No AGP bridge found Node 0: aperture @ f4000000 size 64 MB Node 1: aperture @ f4000000 size 64 MB Node 2: aperture @ f4000000 size 64 MB Node 3: aperture @ f4000000 size 64 MB Memory: 33084308k/34078720k available (3910k kernel code, 524852k absent, 469560k reserved, 1814k data, 372k init) Calibrating delay loop (skipped), value calculated using timer frequency.. 5628.98 BogoMIPS (lpj=11257968) Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes) Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0/0x0 -> Node 0 tseg: 0000000000 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 using C1E aware idle routine ACPI: Core revision 20081204 Setting APIC routing to flat ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 CPU0: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5629.23 BogoMIPS (lpj=11258478) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1/0x1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 2 APIC 0x2 ip 0x6000 Initializing CPU#2 Calibrating delay using timer specific routine.. 5629.24 BogoMIPS (lpj=11258499) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2/0x2 -> Node 1 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 0 x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 CPU2: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 3 APIC 0x3 ip 0x6000 Initializing CPU#3 Calibrating delay using timer specific routine.. 5629.25 BogoMIPS (lpj=11258500) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3/0x3 -> Node 1 CPU: Physical Processor ID: 1 CPU: Processor Core ID: 1 x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 CPU3: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 4 APIC 0x4 ip 0x6000 Initializing CPU#4 Calibrating delay using timer specific routine.. 5629.25 BogoMIPS (lpj=11258500) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 4/0x4 -> Node 2 CPU: Physical Processor ID: 2 CPU: Processor Core ID: 0 x86 PAT enabled: cpu 4, old 0x7040600070406, new 0x7010600070106 CPU4: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 5 APIC 0x5 ip 0x6000 Initializing CPU#5 Calibrating delay using timer specific routine.. 5629.26 BogoMIPS (lpj=11258522) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 5/0x5 -> Node 2 CPU: Physical Processor ID: 2 CPU: Processor Core ID: 1 x86 PAT enabled: cpu 5, old 0x7040600070406, new 0x7010600070106 CPU5: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 6 APIC 0x6 ip 0x6000 Initializing CPU#6 Calibrating delay using timer specific routine.. 5629.25 BogoMIPS (lpj=11258505) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 6/0x6 -> Node 3 CPU: Physical Processor ID: 3 CPU: Processor Core ID: 0 x86 PAT enabled: cpu 6, old 0x7040600070406, new 0x7010600070106 CPU6: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Booting processor 7 APIC 0x7 ip 0x6000 Initializing CPU#7 Calibrating delay using timer specific routine.. 5629.24 BogoMIPS (lpj=11258486) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 7/0x7 -> Node 3 CPU: Physical Processor ID: 3 CPU: Processor Core ID: 1 x86 PAT enabled: cpu 7, old 0x7040600070406, new 0x7010600070106 CPU7: Dual-Core AMD Opteron(tm) Processor 8220 stepping 03 Brought up 8 CPUs Total of 8 processors activated (45033.72 BogoMIPS). net_namespace: 1352 bytes xor: automatically using best checksumming function: generic_sse generic_sse: 8671.000 MB/sec xor: using function: generic_sse (8671.000 MB/sec) NET: Registered protocol family 16 node 0 link 2: io port [9000, cfff] node 1 link 1: io port [d000, ffff] node 1 link 1: io port [1000, 1fff] TOM: 00000000e0000000 aka 3584M node 1 link 1: mmio [fe200000, febfffff] node 1 link 1: mmio [fd500000, fd5fffff] node 0 link 2: mmio [fd600000, fd7fffff] node 0 link 2: mmio [e0000000, e3ffffff] node 1 link 1: mmio [e8000000, ebffffff] node 0 link 2: mmio [a0000, bffff] TOM2: 0000000820000000 aka 33280M bus: [00,05] on node 0 link 2 bus: 00 index 0 io port: [2000, cfff] bus: 00 index 1 io port: [0, fff] bus: 00 index 2 mmio: [fd600000, fe1fffff] bus: 00 index 3 mmio: [e0000000, e7ffffff] bus: 00 index 4 mmio: [a0000, bffff] bus: 00 index 5 mmio: [fec00000, ffffffff] bus: 00 index 6 mmio: [ec000000, fd4fffff] bus: 00 index 7 mmio: [820000000, fcffffffff] bus: [80,84] on node 1 link 1 bus: 80 index 0 io port: [d000, ffff] bus: 80 index 1 io port: [1000, 1fff] bus: 80 index 2 mmio: [fe200000, febfffff] bus: 80 index 3 mmio: [fd500000, fd5fffff] bus: 80 index 4 mmio: [e8000000, ebffffff] ACPI: bus type pci registered PCI: Using configuration type 1 for base access bio: create slab at 0 ACPI: EC: Look up EC in DSDT ACPI: Denied BIOS AML access to invalid port 0x21+0x1 (PIC0) ACPI Exception (dsopcode-0419): AE_AML_ILLEGAL_ADDRESS, During address validation of OpRegion [IRQM] [20081204] ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:00:01.1: reg 10 io port: [0xa400-0xa41f] pci 0000:00:01.1: reg 20 io port: [0x2300-0x233f] pci 0000:00:01.1: reg 24 io port: [0x2340-0x237f] pci 0000:00:01.1: PME# supported from D3hot D3cold pci 0000:00:01.1: PME# disabled pci 0000:00:02.0: reg 10 32bit mmio: [0xfe1fc000-0xfe1fcfff] pci 0000:00:02.0: supports D1 D2 pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:02.0: PME# disabled pci 0000:00:02.1: reg 10 32bit mmio: [0xfe1fdc00-0xfe1fdcff] pci 0000:00:02.1: supports D1 D2 pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:02.1: PME# disabled pci 0000:00:06.0: reg 20 io port: [0xd00-0xd0f] pci 0000:00:07.0: reg 10 io port: [0xb800-0xb807] pci 0000:00:07.0: reg 14 io port: [0xb400-0xb403] pci 0000:00:07.0: reg 18 io port: [0xb000-0xb007] pci 0000:00:07.0: reg 1c io port: [0xac00-0xac03] pci 0000:00:07.0: reg 20 io port: [0xa800-0xa80f] pci 0000:00:07.0: reg 24 32bit mmio: [0xfe1fe000-0xfe1fefff] pci 0000:00:08.0: reg 10 io port: [0xcc00-0xcc07] pci 0000:00:08.0: reg 14 io port: [0xc800-0xc803] pci 0000:00:08.0: reg 18 io port: [0xc400-0xc407] pci 0000:00:08.0: reg 1c io port: [0xc000-0xc003] pci 0000:00:08.0: reg 20 io port: [0xbc00-0xbc0f] pci 0000:00:08.0: reg 24 32bit mmio: [0xfe1ff000-0xfe1fffff] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0b.0: PME# disabled pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0c.0: PME# disabled pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0d.0: PME# disabled pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0e.0: PME# disabled pci 0000:05:06.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff] pci 0000:05:06.0: reg 14 32bit mmio: [0xfdc00000-0xfdc3ffff] pci 0000:05:06.0: reg 18 io port: [0x9000-0x907f] pci 0000:05:06.0: supports D1 D2 pci 0000:05:07.0: reg 10 32bit mmio: [0xfe0ff800-0xfe0fffff] pci 0000:05:07.0: reg 14 32bit mmio: [0xfe0f8000-0xfe0fbfff] pci 0000:05:07.0: supports D1 D2 pci 0000:05:07.0: PME# supported from D0 D1 D2 D3hot pci 0000:05:07.0: PME# disabled pci 0000:00:09.0: transparent bridge pci 0000:00:09.0: bridge io port: [0x9000-0x9fff] pci 0000:00:09.0: bridge 32bit mmio: [0xfd800000-0xfe0fffff] pci 0000:00:09.0: bridge 32bit mmio pref: [0xfb400000-0xfd3fffff] pci 0000:03:00.0: reg 10 64bit mmio: [0xfd7f0000-0xfd7fffff] pci 0000:03:00.0: PME# supported from D3hot D3cold pci 0000:03:00.0: PME# disabled pci 0000:00:0c.0: bridge 32bit mmio: [0xfd700000-0xfd7fffff] pci 0000:02:00.0: reg 10 64bit mmio: [0xfd6f0000-0xfd6fffff] pci 0000:02:00.0: PME# supported from D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:00:0d.0: bridge 32bit mmio: [0xfd600000-0xfd6fffff] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Root Bridge [PCIB] (0000:80) pci 0000:80:01.0: reg 14 32bit mmio: [0xfebfc000-0xfebfcfff] pci 0000:80:08.0: reg 10 io port: [0xfc00-0xfc07] pci 0000:80:08.0: reg 14 io port: [0xf800-0xf803] pci 0000:80:08.0: reg 18 io port: [0xf400-0xf407] pci 0000:80:08.0: reg 1c io port: [0xf000-0xf003] pci 0000:80:08.0: reg 20 io port: [0xec00-0xec0f] pci 0000:80:08.0: reg 24 32bit mmio: [0xfebfd000-0xfebfdfff] pci 0000:80:0d.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:80:0d.0: PME# disabled pci 0000:80:0e.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:80:0e.0: PME# disabled pci 0000:80:10.1: reg 10 64bit mmio: [0xfebfe000-0xfebfefff] pci 0000:80:11.1: reg 10 64bit mmio: [0xfebff000-0xfebfffff] pci 0000:82:03.0: reg 10 io port: [0xd800-0xd8ff] pci 0000:82:03.0: reg 14 64bit mmio: [0xfeafc000-0xfeafffff] pci 0000:82:03.0: reg 1c 64bit mmio: [0xfeae0000-0xfeaeffff] pci 0000:82:03.0: reg 30 32bit mmio: [0xfe400000-0xfe7fffff] pci 0000:82:03.0: supports D1 D2 pci 0000:80:10.0: bridge io port: [0xd000-0xdfff] pci 0000:80:10.0: bridge 32bit mmio: [0xfe200000-0xfeafffff] ACPI: PCI Interrupt Routing Table [\_SB_.PCIB._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGA._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCIB.POGB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *5 ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *5 ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *7 ACPI: PCI Interrupt Link [LNKE] (IRQs 16 17 18 19) *0, disabled. ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *9 ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *11 ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled. ACPI: PCI Interrupt Link [LKSM] (IRQs 20 21 22) *5 ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *11 ACPI: PCI Interrupt Link [LTIE] (IRQs 20 21 22) *10 ACPI: PCI Interrupt Link [LN2A] (IRQs 40 41 42 43) *0, disabled. ACPI: PCI Interrupt Link [LN2B] (IRQs 40 41 42 43) *0, disabled. ACPI: PCI Interrupt Link [LN2C] (IRQs 40 41 42 43) *0, disabled. ACPI: PCI Interrupt Link [LN2D] (IRQs 40 41 42 43) *0, disabled. ACPI: PCI Interrupt Link [LK2N] (IRQs 44 45 46 47) *0, disabled. ACPI: PCI Interrupt Link [LT3D] (IRQs 44 45 46 47) *0, disabled. ACPI: PCI Interrupt Link [LT2E] (IRQs 44 45 46 47) *0, disabled. ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - EE, should be EB [20081204] SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ f4000000 size 65536 KB init_memory_mapping: 00000000f4000000-00000000f8000000 00f4000000 - 00f8000000 page 2M last_map_addr: f8000000 end: f8000000 PCI-DMA: using GART IOMMU. PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 15 devices ACPI: ACPI bus type pnp unregistered system 00:07: ioport range 0x190-0x193 has been reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: iomem range 0xffb80000-0xfffffffe has been reserved system 00:07: iomem range 0xdfefc000-0xdfefcfff could not be reserved system 00:07: iomem range 0xdfefd000-0xdfefd3ff could not be reserved system 00:07: iomem range 0xdfefe000-0xdfefe3ff could not be reserved system 00:07: iomem range 0xdfeff000-0xdfefffff could not be reserved system 00:07: iomem range 0xfefff000-0xfeffffff has been reserved system 00:08: ioport range 0xca2-0xca3 has been reserved system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved system 00:08: iomem range 0xfee00000-0xfeefffff could not be reserved system 00:08: iomem range 0xfe200000-0xfebfffff could not be reserved system 00:08: iomem range 0xfd500000-0xfd5fffff has been reserved system 00:0b: ioport range 0xa00-0xa0f has been reserved system 00:0c: iomem range 0xe0000000-0xefffffff could not be reserved system 00:0d: iomem range 0x0-0x9ffff could not be reserved system 00:0d: iomem range 0xc0000-0xdffff has been reserved system 00:0d: iomem range 0xe0000-0xfffff could not be reserved system 00:0d: iomem range 0x100000-0xdfffffff could not be reserved pci 0000:00:09.0: PCI bridge, secondary bus 0000:05 Switched to high resolution mode on CPU 0 pci 0000:00:09.0: IO window: 0x9000-0x9fff Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 5 Switched to high resolution mode on CPU 4 Switched to high resolution mode on CPU 3 Switched to high resolution mode on CPU 2 Switched to high resolution mode on CPU 7 Switched to high resolution mode on CPU 6 pci 0000:00:09.0: MEM window: 0xfd800000-0xfe0fffff pci 0000:00:09.0: PREFETCH window: 0x000000fb400000-0x000000fd3fffff pci 0000:00:0b.0: PCI bridge, secondary bus 0000:04 pci 0000:00:0b.0: IO window: disabled pci 0000:00:0b.0: MEM window: disabled pci 0000:00:0b.0: PREFETCH window: disabled pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03 pci 0000:00:0c.0: IO window: disabled pci 0000:00:0c.0: MEM window: 0xfd700000-0xfd7fffff pci 0000:00:0c.0: PREFETCH window: disabled pci 0000:00:0d.0: PCI bridge, secondary bus 0000:02 pci 0000:00:0d.0: IO window: disabled pci 0000:00:0d.0: MEM window: 0xfd600000-0xfd6fffff pci 0000:00:0d.0: PREFETCH window: disabled pci 0000:00:0e.0: PCI bridge, secondary bus 0000:01 pci 0000:00:0e.0: IO window: disabled pci 0000:00:0e.0: MEM window: disabled pci 0000:00:0e.0: PREFETCH window: disabled pci 0000:00:09.0: setting latency timer to 64 pci 0000:00:0b.0: setting latency timer to 64 pci 0000:00:0c.0: setting latency timer to 64 pci 0000:00:0d.0: setting latency timer to 64 pci 0000:00:0e.0: setting latency timer to 64 pci 0000:80:0d.0: PCI bridge, secondary bus 0000:84 pci 0000:80:0d.0: IO window: disabled pci 0000:80:0d.0: MEM window: disabled pci 0000:80:0d.0: PREFETCH window: disabled pci 0000:80:0e.0: PCI bridge, secondary bus 0000:83 pci 0000:80:0e.0: IO window: disabled pci 0000:80:0e.0: MEM window: disabled pci 0000:80:0e.0: PREFETCH window: disabled pci 0000:80:10.0: PCI bridge, secondary bus 0000:82 pci 0000:80:10.0: IO window: 0xd000-0xdfff pci 0000:80:10.0: MEM window: 0xfe200000-0xfeafffff pci 0000:80:10.0: PREFETCH window: disabled pci 0000:80:11.0: PCI bridge, secondary bus 0000:81 pci 0000:80:11.0: IO window: disabled pci 0000:80:11.0: MEM window: disabled pci 0000:80:11.0: PREFETCH window: disabled pci 0000:80:0d.0: setting latency timer to 64 pci 0000:80:0e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x2000-0xcfff] pci_bus 0000:00: resource 1 io: [0x00-0xfff] pci_bus 0000:00: resource 2 mem: [0xfd600000-0xfe1fffff] pci_bus 0000:00: resource 3 mem: [0xe0000000-0xe7ffffff] pci_bus 0000:00: resource 4 mem: [0x0a0000-0x0bffff] pci_bus 0000:00: resource 5 mem: [0xfec00000-0xffffffff] pci_bus 0000:00: resource 6 mem: [0xec000000-0xfd4fffff] pci_bus 0000:00: resource 7 mem: [0x820000000-0xfcffffffff] pci_bus 0000:05: resource 0 io: [0x9000-0x9fff] pci_bus 0000:05: resource 1 mem: [0xfd800000-0xfe0fffff] pci_bus 0000:05: resource 2 mem: [0xfb400000-0xfd3fffff] pci_bus 0000:05: resource 3 io: [0x2000-0xcfff] pci_bus 0000:05: resource 4 io: [0x00-0xfff] pci_bus 0000:05: resource 5 mem: [0xfd600000-0xfe1fffff] pci_bus 0000:05: resource 6 mem: [0xe0000000-0xe7ffffff] pci_bus 0000:05: resource 7 mem: [0x0a0000-0x0bffff] pci_bus 0000:05: resource 8 mem: [0xfec00000-0xffffffff] pci_bus 0000:05: resource 9 mem: [0xec000000-0xfd4fffff] pci_bus 0000:05: resource 10 mem: [0x820000000-0xfcffffffff] pci_bus 0000:04: resource 0 mem: [0x0-0x0] pci_bus 0000:04: resource 1 mem: [0x0-0x0] pci_bus 0000:04: resource 2 mem: [0x0-0x0] pci_bus 0000:04: resource 3 mem: [0x0-0x0] pci_bus 0000:03: resource 0 mem: [0x0-0x0] pci_bus 0000:03: resource 1 mem: [0xfd700000-0xfd7fffff] pci_bus 0000:03: resource 2 mem: [0x0-0x0] pci_bus 0000:03: resource 3 mem: [0x0-0x0] pci_bus 0000:02: resource 0 mem: [0x0-0x0] pci_bus 0000:02: resource 1 mem: [0xfd600000-0xfd6fffff] pci_bus 0000:02: resource 2 mem: [0x0-0x0] pci_bus 0000:02: resource 3 mem: [0x0-0x0] pci_bus 0000:01: resource 0 mem: [0x0-0x0] pci_bus 0000:01: resource 1 mem: [0x0-0x0] pci_bus 0000:01: resource 2 mem: [0x0-0x0] pci_bus 0000:01: resource 3 mem: [0x0-0x0] pci_bus 0000:80: resource 0 io: [0xd000-0xffff] pci_bus 0000:80: resource 1 io: [0x1000-0x1fff] pci_bus 0000:80: resource 2 mem: [0xfe200000-0xfebfffff] pci_bus 0000:80: resource 3 mem: [0xfd500000-0xfd5fffff] pci_bus 0000:80: resource 4 mem: [0xe8000000-0xebffffff] pci_bus 0000:84: resource 0 mem: [0x0-0x0] pci_bus 0000:84: resource 1 mem: [0x0-0x0] pci_bus 0000:84: resource 2 mem: [0x0-0x0] pci_bus 0000:84: resource 3 mem: [0x0-0x0] pci_bus 0000:83: resource 0 mem: [0x0-0x0] pci_bus 0000:83: resource 1 mem: [0x0-0x0] pci_bus 0000:83: resource 2 mem: [0x0-0x0] pci_bus 0000:83: resource 3 mem: [0x0-0x0] pci_bus 0000:82: resource 0 io: [0xd000-0xdfff] pci_bus 0000:82: resource 1 mem: [0xfe200000-0xfeafffff] pci_bus 0000:82: resource 2 mem: [0x0-0x0] pci_bus 0000:82: resource 3 mem: [0x0-0x0] pci_bus 0000:81: resource 0 mem: [0x0-0x0] pci_bus 0000:81: resource 1 mem: [0x0-0x0] pci_bus 0000:81: resource 2 mem: [0x0-0x0] pci_bus 0000:81: resource 3 mem: [0x0-0x0] NET: Registered protocol family 2 IP route cache hash table entries: 1048576 (order: 11, 8388608 bytes) TCP established hash table entries: 524288 (order: 11, 8388608 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered NET: Registered protocol family 1 NTFS driver 2.1.29 [Flags: R/W]. SGI XFS with security attributes, large block/inode numbers, no debug enabled msgmni has been set to 32768 alg: No test for cipher_null (cipher_null-generic) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) alg: No test for stdrng (krng) async_tx: api initialized (sync-only) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered pci 0000:00:00.0: Enabling HT MSI Mapping pci 0000:00:0b.0: Found disabled HT MSI Mapping pci 0000:00:00.0: Found enabled HT MSI Mapping pci 0000:00:0b.0: Enabling HT MSI Mapping pci 0000:00:0c.0: Found disabled HT MSI Mapping pci 0000:00:00.0: Found enabled HT MSI Mapping pci 0000:00:0c.0: Enabling HT MSI Mapping pci 0000:00:0d.0: Found disabled HT MSI Mapping pci 0000:00:00.0: Found enabled HT MSI Mapping pci 0000:00:0d.0: Enabling HT MSI Mapping pci 0000:00:0e.0: Found disabled HT MSI Mapping pci 0000:00:00.0: Found enabled HT MSI Mapping pci 0000:00:0e.0: Enabling HT MSI Mapping pci 0000:80:00.0: Enabling HT MSI Mapping pci 0000:80:0d.0: Found disabled HT MSI Mapping pci 0000:80:00.0: Found enabled HT MSI Mapping pci 0000:80:0d.0: Enabling HT MSI Mapping pci 0000:80:0e.0: Found disabled HT MSI Mapping pci 0000:80:00.0: Found enabled HT MSI Mapping pci 0000:80:0e.0: Enabling HT MSI Mapping pci 0000:80:10.0: Found disabled HT MSI Mapping pci 0000:80:10.0: MSI quirk detected; subordinate MSI disabled pci 0000:80:11.0: Found disabled HT MSI Mapping pci 0000:80:11.0: MSI quirk detected; subordinate MSI disabled pcieport-driver 0000:00:0b.0: setting latency timer to 64 pcieport-driver 0000:00:0b.0: irq 86 for MSI/MSI-X pcieport-driver 0000:00:0c.0: setting latency timer to 64 pcieport-driver 0000:00:0c.0: irq 87 for MSI/MSI-X pcieport-driver 0000:00:0d.0: setting latency timer to 64 pcieport-driver 0000:00:0d.0: irq 88 for MSI/MSI-X pcieport-driver 0000:00:0e.0: setting latency timer to 64 pcieport-driver 0000:00:0e.0: irq 89 for MSI/MSI-X pcieport-driver 0000:80:0d.0: setting latency timer to 64 pcieport-driver 0000:80:0d.0: irq 90 for MSI/MSI-X pcieport-driver 0000:80:0e.0: setting latency timer to 64 pcieport-driver 0000:80:0e.0: irq 91 for MSI/MSI-X lp: driver loaded but no devices found Real Time Clock Driver v1.12b Linux agpgart interface v0.103 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A floppy0: no floppy controllers found brd: module loaded loop: module loaded nbd: registered device at major 43 Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008) bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI e100: Copyright(c) 1999-2006 Intel Corporation tg3.c:v3.97 (December 10, 2008) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 19 tg3 0000:03:00.0: PCI INT A -> Link[LNKA] -> GSI 19 (level, low) -> IRQ 19 tg3 0000:03:00.0: setting latency timer to 64 tg3 0000:03:00.0: PME# disabled eth0: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:d0:68:12:f6:fd eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1]) eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] eth0: dma_rwctrl[76180000] dma_mask[64-bit] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 18 tg3 0000:02:00.0: PCI INT A -> Link[LNKD] -> GSI 18 (level, low) -> IRQ 18 tg3 0000:02:00.0: setting latency timer to 64 tg3 0000:02:00.0: PME# disabled eth1: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:d0:68:12:f6:fc eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1]) eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] eth1: dma_rwctrl[76180000] dma_mask[64-bit] tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky Adaptec aacraid driver 1.1-5[2456]-ms QLogic Fibre Channel HBA Driver: 8.03.00-k2 megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) megasas: 00.00.04.01 Thu July 24 11:41:51 PST 2008 3ware 9000 Storage Controller device driver for Linux v2.26.02.011. st: Version 20081215, fixed bufsize 32768, s/g segs 256 Driver 'st' needs updating - please use bus_type methods Driver 'sd' needs updating - please use bus_type methods Driver 'sr' needs updating - please use bus_type methods SCSI Media Changer driver v0.25 Driver 'ch' needs updating - please use bus_type methods sata_nv 0000:00:07.0: version 3.5 ACPI: PCI Interrupt Link [LTID] enabled at IRQ 22 sata_nv 0000:00:07.0: PCI INT A -> Link[LTID] -> GSI 22 (level, low) -> IRQ 22 sata_nv 0000:00:07.0: setting latency timer to 64 scsi0 : sata_nv scsi1 : sata_nv ata1: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xa800 irq 22 ata2: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa808 irq 22 ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) ACPI: PCI Interrupt Link [LTIE] enabled at IRQ 21 sata_nv 0000:00:08.0: PCI INT A -> Link[LTIE] -> GSI 21 (level, low) -> IRQ 21 sata_nv 0000:00:08.0: setting latency timer to 64 scsi2 : sata_nv scsi3 : sata_nv ata3: SATA max UDMA/133 cmd 0xcc00 ctl 0xc800 bmdma 0xbc00 irq 21 ata4: SATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xbc08 irq 21 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ACPI: PCI Interrupt Link [LT2E] enabled at IRQ 47 sata_nv 0000:80:08.0: PCI INT A -> Link[LT2E] -> GSI 47 (level, low) -> IRQ 47 sata_nv 0000:80:08.0: setting latency timer to 64 scsi4 : sata_nv scsi5 : sata_nv ata5: SATA max UDMA/133 cmd 0xfc00 ctl 0xf800 bmdma 0xec00 irq 47 ata6: SATA max UDMA/133 cmd 0xf400 ctl 0xf000 bmdma 0xec08 irq 47 ata5: SATA link down (SStatus 0 SControl 300) ata6: SATA link down (SStatus 0 SControl 300) pata_amd 0000:00:06.0: version 0.3.11 pata_amd 0000:00:06.0: setting latency timer to 64 scsi6 : pata_amd scsi7 : pata_amd ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xd00 irq 14 ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xd08 irq 15 ata7.01: ATAPI: TSSTcorpCD-ROM TS-L162C, MO00, max UDMA/33 ata7: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc00000) ACPI=0x701f (900:54:0x14) ata7.01: configured for UDMA/33 scsi 6:0:1:0: CD-ROM TSSTcorp CD-ROM TS-L162C MO00 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 6:0:1:0: Attached scsi CD-ROM sr0 sr 6:0:1:0: Attached scsi generic sg0 type 5 I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.04.07 Copyright (c) 1999-2008 LSI Corporation Fusion MPT SPI Host driver 3.04.07 Fusion MPT FC Host driver 3.04.07 Fusion MPT SAS Host driver 3.04.07 mptsas 0000:82:03.0: PCI INT A -> GSI 75 (level, low) -> IRQ 75 mptbase: ioc0: Initiating bringup ioc0: LSISAS1068 B1: Capabilities={Initiator} scsi8 : ioc0: LSISAS1068 B1, FwRev=01120000h, Ports=1, MaxQ=511, IRQ=75 scsi 8:0:0:0: Direct-Access SEAGATE ST3146855SS RS02 PQ: 0 ANSI: 5 scsi 8:0:0:0: Attached scsi generic sg1 type 0 scsi 8:0:1:0: Direct-Access SEAGATE ST3146855SS RS02 PQ: 0 ANSI: 5 scsi 8:0:1:0: Attached scsi generic sg2 type 0 scsi 8:1:0:0: Direct-Access LSILOGIC Logical Volume 3000 PQ: 0 ANSI: 2 sd 8:1:0:0: [sda] 285155328 512-byte hardware sectors: (145 GB/135 GiB) sd 8:1:0:0: [sda] Write Protect is off sd 8:1:0:0: [sda] Mode Sense: 03 00 00 08 sd 8:1:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 8:1:0:0: [sda] 285155328 512-byte hardware sectors: (145 GB/135 GiB) sd 8:1:0:0: [sda] Write Protect is off sd 8:1:0:0: [sda] Mode Sense: 03 00 00 08 sd 8:1:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 8:1:0:0: [sda] Attached SCSI disk sd 8:1:0:0: Attached scsi generic sg3 type 0 Fusion MPT misc device (ioctl) driver 3.04.07 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 ACPI: I/O resource nForce2_smbus [0x2300-0x233f] conflicts with ACPI region SMRG [0x2300-0x2304] ACPI: Device needs an ACPI driver i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2300 i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2340 hdaps: supported laptop not found! hdaps: driver init failed (ret=-19)! k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 k8temp 0000:00:19.3: Temperature readouts might be wrong - check erratum #141 k8temp 0000:00:1a.3: Temperature readouts might be wrong - check erratum #141 k8temp 0000:00:1b.3: Temperature readouts might be wrong - check erratum #141 md: raid1 personality registered for level 1 raid6: int64x1 2540 MB/s raid6: int64x2 3386 MB/s raid6: int64x4 3191 MB/s raid6: int64x8 2263 MB/s raid6: sse2x1 3888 MB/s raid6: sse2x2 5188 MB/s raid6: sse2x4 5257 MB/s raid6: using algorithm sse2x4 (5257 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 cpuidle: using governor ladder cpuidle: using governor menu oprofile: using NMI interrupt. Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ctnetlink v0.93: registering with nfnetlink. NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. UDF-fs: No VRS found XFS mounting filesystem sda3 Ending clean XFS mount for filesystem: sda3 VFS: Mounted root (xfs filesystem) readonly on device 8:3. Freeing unused kernel memory: 372k freed Adding 2048276k swap on /dev/sda1. Priority:-1 extents:1 across:2048276k XFS mounting filesystem sda4 Ending clean XFS mount for filesystem: sda4 warning: `ntpd' uses 32-bit capabilities (legacy support in use) tg3 0000:03:00.0: PME# disabled tg3: eth0: Link is up at 1000 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX.