BIOS EBDA/lowmem at: 0009f000/0009f000 Initializing cgroup subsys cpuset Linux version 2.6.28.3-250Hz (root@harley) (gcc version 4.3.1 20080507 (prerelease) [gcc-4_3-branch revision 135036] (SUSE Linux) ) #7 SMP PREEMPT Fri Feb 2 0 09:01:54 EST 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000bffe0000 (usable) BIOS-e820: 00000000bffe0000 - 00000000bffe3000 (ACPI NVS) BIOS-e820: 00000000bffe3000 - 00000000bfff0000 (ACPI data) BIOS-e820: 00000000bfff0000 - 00000000c0000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000140000000 (usable) DMI 2.5 present. Phoenix BIOS detected: BIOS may corrupt low RAM, working it around. last_pfn = 0xbffe0 max_arch_pfn = 0x100000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 RAMDISK: 374cf000 - 37fef1ba Allocated new RAMDISK: 004a7000 - 00fc71ba Move RAMDISK from 00000000374cf000 - 0000000037fef1b9 to 004a7000 - 00fc71b9 ACPI: RSDP 000F7FB0, 0024 (r2 RX780 ) ACPI: XSDT BFFE3080, 004C (r1 RX780 AWRDACPI 42302E31 AWRD 0) ACPI: FACP BFFE8C80, 00F4 (r3 RX780 AWRDACPI 42302E31 AWRD 0) FADT: X_PM1a_EVT_BLK.bit_width (8) does not match PM1_EVT_LEN (4) ACPI: DSDT BFFE3200, 5A71 (r1 RX780 AWRDACPI 1000 MSFT 100000E) ACPI: FACS BFFE0000, 0040 ACPI: SSDT BFFE8E40, 088C (r1 PTLTD POWERNOW 1 LTP 1) ACPI: HPET BFFE9700, 0038 (r1 RX780 AWRDACPI 42302E31 AWRD 98) ACPI: MCFG BFFE9740, 003C (r1 RX780 AWRDACPI 42302E31 AWRD 0) ACPI: APIC BFFE8D80, 0084 (r1 RX780 AWRDACPI 42302E31 AWRD 0) 2183MB HIGHMEM available. 887MB LOWMEM available. mapped low ram: 0 - 377fe000 low ram: 00000000 - 377fe000 bootmap 00012000 - 00018f00 (9 early reservations) ==> bootmem [0000000000 - 00377fe000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 00004a3c54] TEXT DATA BSS ==> [0000100000 - 00004a3c54] #4 [00004a4000 - 00004a7000] INIT_PG_TABLE ==> [00004a4000 - 00004a7000] #5 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 - 0000100000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000] #7 [00004a7000 - 0000fc71ba] NEW RAMDISK ==> [00004a7000 - 0000fc71ba] #8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000] Scan SMP from c0000000 for 1024 bytes. Scan SMP from c009fc00 for 1024 bytes. Scan SMP from c00f0000 for 65536 bytes. found SMP MP-table at [c00f3f00] 000f3f00 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 Normal 0x00001000 -> 0x000377fe HighMem 0x000377fe -> 0x000bffe0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009f 0: 0x00000100 -> 0x000bffe0 ACPI: PM-Timer IO Port: 0x4008 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) Enabling APIC mode: Flat. Using 1 I/O APICs ACPI: HPET id: 0x10b9a201 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information SMP: Allowing 4 CPUs, 0 hotplug CPUs mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Allocating PCI resources starting at c2000000 (gap: c0000000:20000000) PERCPU: Allocating 36864 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 780143 Kernel command line: root=/dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part5 apm=off selinux=0 noresume splash=silent apic=debug hpet=debug console=ttyS0,19200n 8 vga=normal Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 Preemptible RCU implementation. PID hash table entries: 4096 (order: 12, 16384 bytes) Fast TSC calibration using PIT Detected 3000.190 MHz processor. Console: colour VGA+ 80x25 console [ttyS0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 3103452k/3145600k available (1836k kernel code, 40788k reserved, 1098k data, 276k init, 2236296k highmem) virtual kernel memory layout: fixmap : 0xffe19000 - 0xfffff000 (1944 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB) lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB) .init : 0xc03e3000 - 0xc0428000 ( 276 kB) .data : 0xc02cb157 - 0xc03ddc4c (1098 kB) .text : 0xc0100000 - 0xc02cb157 (1836 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 HPET: 4 timers in total, 0 timers will be used for per-cpu timer Calibrating delay loop (skipped), value calculated using timer frequency.. 6000.38 BogoMIPS (lpj=12000760) Security Framework initialized Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 using C1E aware idle routine Checking 'hlt' instruction... OK. ACPI: Core revision 20080926 Getting VERSION: 80050010 Getting VERSION: 80050010 Getting ID: 0 Getting ID: f000000 Getting LVT0: 700 Getting LVT1: 400 enabled ExtINT on CPU#0 ENABLING IO-APIC IRQs ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: AMD Phenom(tm) II X4 940 Processor stepping 02 Using local APIC timer interrupts. calibrating APIC timer ... ... lapic delta = 1250071 ... PM timer delta = 357950 ... PM timer result ok ..... delta 1250071 ..... mult: 53686785 ..... calibration result: 800045 ..... CPU clock speed is 3000.0679 MHz. ..... host bus clock speed is 200.0045 MHz. Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 masked ExtINT on CPU#1 Calibrating delay using timer specific routine.. 6000.41 BogoMIPS (lpj=12000822) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: AMD Phenom(tm) II X4 940 Processor stepping 02 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Booting processor 2 APIC 0x2 ip 0x6000 Initializing CPU#2 masked ExtINT on CPU#2 Calibrating delay using timer specific routine.. 6000.40 BogoMIPS (lpj=12000818) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 CPU2: AMD Phenom(tm) II X4 940 Processor stepping 02 checking TSC synchronization [CPU#0 -> CPU#2]: passed. Booting processor 3 APIC 0x3 ip 0x6000 Initializing CPU#3 masked ExtINT on CPU#3 Calibrating delay using timer specific routine.. 6000.41 BogoMIPS (lpj=12000824) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 CPU3: AMD Phenom(tm) II X4 940 Processor stepping 02 checking TSC synchronization [CPU#0 -> CPU#3]: passed. Brought up 4 CPUs Total of 4 processors activated (24001.61 BogoMIPS). net_namespace: 776 bytes NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 PCI: MCFG area at e0000000 reserved in E820 PCI: Using MMCONFIG for extended config space PCI: Using configuration type 1 for base access ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:02.0: PME# supported from D0 D3hot D3cold pci 0000:00:02.0: PME# disabled pci 0000:00:04.0: PME# supported from D0 D3hot D3cold pci 0000:00:04.0: PME# disabled pci 0000:00:06.0: PME# supported from D0 D3hot D3cold pci 0000:00:06.0: PME# disabled pci 0000:00:07.0: PME# supported from D0 D3hot D3cold pci 0000:00:07.0: PME# disabled pci 0000:00:12.0: set SATA to AHCI mode pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot pci 0000:00:13.5: PME# disabled pci 0000:00:14.2: PME# supported from D0 D3hot D3cold pci 0000:00:14.2: PME# disabled pci 0000:02:00.0: PME# supported from D0 D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:03:00.0: PME# supported from D3hot pci 0000:03:00.0: PME# disabled pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:04:00.0: PME# disabled pci 0000:00:14.4: transparent bridge ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled. PCI: Using ACPI for IRQ routing pci 0000:00:00.0: BAR 3: can't allocate resource ... APIC ID: 00000000 (0) ... APIC VERSION: 80050010 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000010000000000000000 ... APIC ID: 01000000 (1) ... APIC VERSION: 80050010 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000010000000000000000 ... APIC ID: 02000000 (2) ... APIC VERSION: 80050010 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000010000000000001000 ... APIC ID: 03000000 (3) ... APIC VERSION: 80050010 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000000000000000000000 00000000000000010000000000001000 testing the IO APIC....................... .................................... done. hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 hpet0: 4 comparators, 32-bit 14.318180 MHz counter Switched to NOHz mode on CPU #0 Switched to NOHz mode on CPU #1 Switched to NOHz mode on CPU #2 Switched to NOHz mode on CPU #3 pnp: PnP ACPI init ACPI: bus type pnp registered pnp 00:0d: mem resource (0xf0000-0xfffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling pnp 00:0d: mem resource (0x0-0x1fffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling pnp 00:0d: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling pnp 00:0d: mem resource (0x100000-0xbffdffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP system 00:01: ioport range 0x4100-0x411f has been reserved system 00:01: ioport range 0x228-0x22f has been reserved system 00:01: ioport range 0x40b-0x40b has been reserved system 00:01: ioport range 0x4d6-0x4d6 has been reserved system 00:01: ioport range 0xc00-0xc01 has been reserved system 00:01: ioport range 0xc14-0xc14 has been reserved system 00:01: ioport range 0xc50-0xc52 has been reserved system 00:01: ioport range 0xc6c-0xc6d has been reserved system 00:01: ioport range 0xc6f-0xc6f has been reserved system 00:01: ioport range 0xcd0-0xcd1 has been reserved system 00:01: ioport range 0xcd2-0xcd3 has been reserved system 00:01: ioport range 0xcd4-0xcdf has been reserved system 00:01: ioport range 0x4000-0x40fe has been reserved system 00:01: ioport range 0x4210-0x4217 has been reserved system 00:01: ioport range 0xb10-0xb1f has been reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: ioport range 0x220-0x225 has been reserved system 00:0d: iomem range 0xfed00000-0xfed000ff has been reserved system 00:0d: iomem range 0xbffe0000-0xbfffffff could not be reserved system 00:0d: iomem range 0xffff0000-0xffffffff has been reserved system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0d: iomem range 0xfff80000-0xfffeffff has been reserved pci 0000:00:02.0: PCI bridge, secondary bus 0000:01 pci 0000:00:02.0: IO window: 0xd000-0xdfff pci 0000:00:02.0: MEM window: 0xf8000000-0xfbffffff pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000dfffffff pci 0000:00:04.0: PCI bridge, secondary bus 0000:02 pci 0000:00:04.0: IO window: 0xc000-0xcfff pci 0000:00:04.0: MEM window: 0xfdb00000-0xfdbfffff pci 0000:00:04.0: PREFETCH window: 0x000000fda00000-0x000000fdafffff pci 0000:00:06.0: PCI bridge, secondary bus 0000:03 pci 0000:00:06.0: IO window: 0xb000-0xbfff pci 0000:00:06.0: MEM window: 0xfdf00000-0xfdffffff pci 0000:00:06.0: PREFETCH window: 0x000000fde00000-0x000000fdefffff pci 0000:00:07.0: PCI bridge, secondary bus 0000:04 pci 0000:00:07.0: IO window: 0xe000-0xefff pci 0000:00:07.0: MEM window: 0xfdd00000-0xfddfffff pci 0000:00:07.0: PREFETCH window: 0x000000fdc00000-0x000000fdcfffff pci 0000:00:14.4: PCI bridge, secondary bus 0000:05 pci 0000:00:14.4: IO window: 0xa000-0xafff pci 0000:00:14.4: MEM window: 0xfd900000-0xfd9fffff pci 0000:00:14.4: PREFETCH window: 0x000000fd800000-0x000000fd8fffff pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:06.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 bus: 00 index 0 io port: [0x00-0xffff] bus: 00 index 1 mmio: [0x000000-0xffffffff] bus: 01 index 0 io port: [0xd000-0xdfff] bus: 01 index 1 mmio: [0xf8000000-0xfbffffff] bus: 01 index 2 mmio: [0xc0000000-0xdfffffff] bus: 01 index 3 mmio: [0x0-0x0] bus: 02 index 0 io port: [0xc000-0xcfff] bus: 02 index 1 mmio: [0xfdb00000-0xfdbfffff] bus: 02 index 2 mmio: [0xfda00000-0xfdafffff] bus: 02 index 3 mmio: [0x0-0x0] bus: 03 index 0 io port: [0xb000-0xbfff] bus: 03 index 1 mmio: [0xfdf00000-0xfdffffff] bus: 03 index 2 mmio: [0xfde00000-0xfdefffff] bus: 03 index 3 mmio: [0x0-0x0] bus: 04 index 0 io port: [0xe000-0xefff] bus: 04 index 1 mmio: [0xfdd00000-0xfddfffff] bus: 04 index 2 mmio: [0xfdc00000-0xfdcfffff] bus: 04 index 3 mmio: [0x0-0x0] bus: 05 index 0 io port: [0xa000-0xafff] bus: 05 index 1 mmio: [0xfd900000-0xfd9fffff] bus: 05 index 2 mmio: [0xfd800000-0xfd8fffff] bus: 05 index 3 io port: [0x00-0xffff] bus: 05 index 4 mmio: [0x000000-0xffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 Unpacking initramfs... done Freeing initrd memory: 11392k freed audit: initializing netlink socket (disabled) type=2000 audit(1235121981.180:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1717 alg: No test for stdrng (krng) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pcieport-driver 0000:00:02.0: found MSI capability pcieport-driver 0000:00:04.0: found MSI capability pcieport-driver 0000:00:06.0: found MSI capability pcieport-driver 0000:00:07.0: found MSI capability isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 Using IPI No-Shortcut mode Freeing unused kernel memory: 276k freed doing fast boot Boot logging started on /dev/ttSCSI subsystem initialized yS0(/dev/console) at Fri Feb 20 pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001) 09:26:22 2009 pata_jmicron 0000:03:00.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 scsi0 : pata_jmicron FATAL: Module prscsi1 : pata_jmicron ocessor not founata1: PATA max UDMA/100 cmd 0xbf00 ctl 0xbe00 bmdma 0xbb00 irq 19 ata2: PATA max UDMA/100 cmd 0xbd00 ctl 0xbc00 bmdma 0xbb08 irq 19 d. FATAL: Module thermal not found. logips2pp: Detected unknown logitech mouse model 11 ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio scsi2 : ahci scsi3 : ahci scsi4 : ahci scsi5 : ahci ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22 ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22 ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22 ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22 input: ImPS/2 Logitech Wheel Mouse as /class/input/input2 ata3: softreset failed (device not ready) ata3: failed due to HW bug, retry pmp=0 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32) ata3.00: SB600 AHCI: limiting to 255 sectors per cmd ata3.00: SB600 AHCI: limiting to 255 sectors per cmd ata3.00: configured for UDMA/133 ata4: softreset failed (device not ready) ata4: failed due to HW bug, retry pmp=0 ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 ata4.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32) ata4.00: SB600 AHCI: limiting to 255 sectors per cmd ata4.00: SB600 AHCI: limiting to 255 sectors per cmd ata4.00: configured for UDMA/133 ata5: softreset failed (device not ready) ata5: failed due to HW bug, retry pmp=0 ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 ata5.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32) ata5.00: SB600 AHCI: limiting to 255 sectors per cmd ata5.00: SB600 AHCI: limiting to 255 sectors per cmd ata5.00: configured for UDMA/133 ata6: SATA link down (SStatus 0 SControl 300) scsi 2:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 3:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 scsi 4:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 ahci 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part scsi6 : ahci scsi7 : ahci ata7: SATA max UDMA/133 abar m8192@0xfdffe000 port 0xfdffe100 irq 18 ata8: SATA max UDMA/133 abar m8192@0xfdffe000 port 0xfdffe180 irq 18 ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) Uniform Multi-Platform E-IDE driver atiixp 0000:00:14.1: IDE controller (0x1002:0x438c rev 0x00) ATIIXP_IDE 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 atiixp 0000:00:14.1: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf900-0xf907 hda: ST3120023A, ATA DISK drive hdb: TSSTcorpCD/DVDW TS-H552B, ATAPI CD/DVD-ROM drive hda: UDMA/100 mode selected hdb: UDMA/33 mode selected ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 aic7xxx 0000:05:06.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 scsi8 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs scsi 8:0:0:0: Direct-Access SEAGATE ST15150N 5052 PQ: 0 ANSI: 2 scsi8:A:0:0: Tagged Queuing enabled. Depth 32 target8:0:0: Beginning Domain Validation target8:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target8:0:0: Domain Validation skipping write tests target8:0:0: Ending Domain Validation scsi 8:0:2:0: Sequential-Access ARCHIVE Python 01931-XXX 5.63 PQ: 0 ANSI: 2 target8:0:2: Beginning Domain Validation target8:0:2: FAST-10 SCSI 7.8 MB/s ST (128 ns, offset 15) target8:0:2: Domain Validation skipping write tests target8:0:2: Ending Domain Validation FATAL: Module fan not found. BIOS EDD facility v0.16 2004-Jun-25, 4 devices found sky2 driver version 1.22 sky2 0000:04:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 sky2 0000:04:00.0: Yukon-2 EC Ultra chip revision 5 sky2 0000:04:00.0: Marvell Yukon 88E8056 Gigabit Ethernet Controller sky2 eth0: addr 00:e0:4d:7a:8c:ee Intel(R) PRO/1000 Network Driver - version 7.3.20-k3-NAPI Copyright (c) 1999-2006 Intel Corporation. Creating device nodes with udev Driver 'sd' needs updating - please use bus_type methods sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB) usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after ohci_hcd 0000:00:13.0: OHCI Host Controller sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 2:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 2:0:0:0: [sda] Write Protect is off sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 > ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 sd 2:0:0:0: [sda] Attached SCSI disk sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000 sd 3:0:0:0: [sdb] Attached SCSI disk sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sdc] 625142448 512-byte hardware sectors: (320 GB/298 GiB) sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 4:0:0:0: [sdc] Attached SCSI disk usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 sd 8:0:0:0: [sdd] READ CAPACITY failed sd 8:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK sd 8:0:0:0: [sdd] Sense Key : Medium Error [current] sd 8:0:0:0: [sdd] Add. Sense: Medium format corrupted sd 8:0:0:0: [sdd] Write Protect is off sd 8:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 8:0:0:0: [sdd] Attached SCSI disk usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.28.3-250Hz ohci_hcd usb usb1: SerialNumber: 0000:00:13.0 ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19 ehci_hcd 0000:00:13.5: EHCI Host Controller ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround ehci_hcd 0000:00:13.5: debug port 1 usb 1-1: new full speed USB device using ohci_hcd and address 2 ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000 ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: EHCI Host Controller usb usb2: Manufacturer: Linux 2.6.28.3-250Hz ehci_hcd usb usb2: SerialNumber: 0000:00:13.5 ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000 usb usb3: configuration #1 chosen from 1 choice usb 1-1: device not accepting address 2, error -62 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 1-0:1.0: unable to enumerate USB device on port 1 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.28.3-250Hz ohci_hcd usb usb3: SerialNumber: 0000:00:13.1 ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.2: OHCI Host Controller ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found usb 2-1: new high speed USB device using ehci_hcd and address 2 hub 4-0:1.0: 2 ports detected usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.28.3-250Hz ohci_hcd usb usb4: SerialNumber: 0000:00:13.2 usb 2-1: configuration #1 chosen from 1 choice usb 2-1: New USB device found, idVendor=03f0, idProduct=5111 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Photosmart 3200 series usb 2-1: Manufacturer: HP usb 2-1: SerialNumber: MY5B98310Z045K ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 ohci_hcd 0000:00:13.3: OHCI Host Controller ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5 ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: OHCI Host Controller usb usb5: Manufacturer: Linux 2.6.28.3-250Hz ohci_hcd usb usb5: SerialNumber: 0000:00:13.3 usb 1-2: new full speed USB device using ohci_hcd and address 4 ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.4: OHCI Host Controller ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6 ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000 usb 1-2: device descriptor read/64, error -62 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: OHCI Host Controller usb usb6: Manufacturer: Linux 2.6.28.3-250Hz ohci_hcd usb 1-2: device descriptor read/64, error -62 usb usb6: SerialNumber: 0000:00:13.4 Waiting for device /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part5 to appear: ok showconsole: Warning: the ioctl TIOCGDEV is not known by the kernel fsck 1.40.8 (13-Mar-2008) [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/dusb 1-2: new full speed USB device using ohci_hcd and address 5 isk/by-id/ata-ST3320620AS_6QF4HDV5-part5 usb 1-2: device descriptor read/64, error -62 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part5: Superblock last kjournald starting. Commit interval 5 seconds write time is inEXT3 FS on sda5, the future. FIinternal journal XED. /dev/diskEXT3-fs: mounted filesystem with ordered data mode. /by-id/ata-ST3320620AS_6QF4HDV5-part5: clean, 346619/3280320 files, 4787045/6554512 blocks fsck succeeded. Mounting root device read-write. Mounting root /dev/disk/by-id/ata-ST3320620AS_6Qusb 1-2: device descriptor read/64, error -62 F4HDV5-part5 usb 1-2: new full speed USB device using ohci_hcd and address 6 INIT: version 2.86 booting usb 1-2: device not accepting address 6, error -62 usb 1-2: new full speed USB device using ohci_hcd and address 7 System Boot Control: Running /etc/init.d/boot Mounting procfs at /proc sb 1-2: device not accepting address 7, error -62 mdone ub 1-0:1.0: unable to enumerate USB device on port 2 h Mounting sysfs at /sys done Mounting debugfs at /sys/kernel/debug done Initializing /dev done Mounting devpts at /dev/pts done done Starting udevd: sd 2:0:0:0: Attached scsi generic sg0 type 0 sd 3:0:0:0: Attached scsi generic sg1 type 0 sd 4:0:0:0: Attached scsi generic sg2 type 0 sd 8:0:0:0: Attached scsi generic sg3 type 0 scsi 8:0:2:0: Attached scsi generic sg4 type 1 e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 e1000e: Copyright (c) 1999-2008 Intel Corporation. e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 0000:02:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:1b:21:0f:09:1b st: Version 20080504, fixed bufsize 32768, s/g segs 256 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection 0000:02:00.0: eth1: MAC: 1, PHY: 4, PBA No: d50854-003 Driver 'st' needs updating - please use bus_type methods st 8:0:2:0: Attached scsi tape st0 st 8:0:2:0: st0: try direct i/o: yes (alignment 4 B) Linux agpgart interface v0.103 Initializing USB Mass Storage driver... scsi9 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage ide-gd driver 1.18 hda: max request size: 128KiB hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63 hda: cache flushes supported hda: hda1 USB Mass Storage support registered. usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x5111 rtc_cmos 00:04: RTC can wake from S4 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, 242 bytes nvram, hpet irqs usbcore: registered new interface driver usblp osst :I: Tape driver with OnStream support version 0.99.4 osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0 Driver 'osst' needs updating - please use bus_type methods ide-cd driver 5.00 ide-cd: hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 IT8718 SuperIO detected. parport_pc 00:0a: reported by Plug and Play ACPI parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ppdev: user-space parallel port driver hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... done Loading required kernel modules done Activating swap-devices in /etc/fstab... Adding 8393952k swap on /dev/sda2. Priority:-1 extents:1 across:8393952k Adding 8393952k swap on /dev/sdb2. Priority:-2 extents:1 across:83939done showconsole: Warning: the ioctl TIOCGDEV is not known by the kernel mount: according to mtab, /dev/sda5 is already mounted on / Setting up the hardware clock done Activating device mapper... device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com done Checking file systems... fsck 1.40.8 (13-Mar-2008) Checking all file systems. [/sbin/fsck.ext3 (1) -- /11.1] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part5 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part5: clean, 244963/1640160 files, 1886024/6554512 blocks [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part1 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part1: clean, 141/131616 files, 97801/263056 blocks [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part6 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part6: clean, 84104/5903072 files, 1455969/11797726 blocks [/sbin/fsck.ext3 (1) -- /misc] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part7 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part7: clean, 10/8536064 files, 313923/17040940 blocks [/sbin/fsck.ext3 (1) -- /usr/local] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part8 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part8: clean, 10111/656000 files, 562964/1311297 blocks [/sbin/fsck.ext3 (1) -- /usr/src] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part9 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part9: clean, 988853/6557152 files, 10060855/13109032 blocks [/sbin/fsck.ext3 (1) -- /misc1] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part10 /dev/disk/by-id/ata-ST3320620AS_6QF4HDV5-part10: clean, 13/12992512 files, 455787/25967056 blocks [/sbin/fsck.ext3 (1) -- /11.1/boot] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part1 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part1: clean, 50/65808 files, 23165/263056 blocks [/sbin/fsck.ext3 (1) -- /11.1/home] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part6 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part6: clean, 85254/2951536 files, 1459985/11797726 blocks [/sbin/fsck.ext3 (1) -- /11.1/misc] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part7 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part7: clean, 10/4268032 files, 313922/17040940 blocks [/sbin/fsck.ext3 (1) -- /11.1/usr/local] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part8 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part8: clean, 10114/328000 files, 562986/1311297 blocks [/sbin/fsck.ext3 (1) -- /11.1/usr/src] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part9 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part9: clean, 224708/3278576 files, 2125826/13109032 blocks [/sbin/fsck.ext3 (1) -- /11.1/misc1] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part10 scsi 9:0:0:0: Direct-Access HP Photosmart 3210 1.00 PQ: 0 ANSI: 2 sd 9:0:0:0: [sde] Attached SCSI removable disk sd 9:0:0:0: Attached scsi generic sg5 type 0 /dev/disk/by-id/ata-ST3320620AS_6QF4HZYT-part10: clean, 11/6496256 files, 455784/25967056 blocks [/sbin/fsck.ext3 (1) -- /local] fsck.ext3 -a /dev/disk/by-id/ata-ST3320620AS_6QF4HDWN-part1 /dev/disk/by-id/ata-ST3320620AS_6QF4HDWN-part1: clean, 1673848/39075840 files, 21295338/78142160 blocks [/sbin/fsck.ext3 (1) -- /lcrs] fsck.ext3 -a /dev/disk/by-id/ata-ST3120023A_3KA0P431-part1 /dev/disk/by-id/ata-ST3120023A_3KA0P431-part1: clean, 32325/14663680 files, 24187969/29302552 blloop: module loaded ocks done journald starting. Commit interval 5 seconds XT3 FS odointernal journal ne EXT3-fs: mounted filesystem with ordered data mode. Mounting local file systems... kjournald starting. Commit interval 5 seconds proc on /proc tyEXT3 FS on sda6, internal journal pe proc (rw) syEXT3-fs: mounted filesystem with ordered data mode. sfs on /sys type sysfs (rw) debkjournald starting. Commit interval 5 seconds ugfs on /sys/kerEXT3 FS on sda7, internal journal nel/debug type dEXT3-fs: mounted filesystem with ordered data mode. ebugfs (rw) udev on /dev type tmpfs (rw) devptkjournald starting. Commit interval 5 seconds s on /dev/pts tyEXT3 FS on sda8, pe devpts (rw,mointernal journal de=0620,gid=5) EXT3-fs: mounted filesystem with ordered data mode. /dev/sda1 on /boot type ext3 (rw,acl,user_xattr)kjournald starting. Commit interval 5 seconds /dev/sda6 on /EXT3 FS on sda9, internal journal home type ext3 (EXT3-fs: mounted filesystem with ordered data mode. rw,acl,user_xattr) /dev/sda7 on /misc type ext3 (rw,acl,user_xakjournald starting. Commit interval 5 seconds ttr) /dev/sda8 EXT3 FS on sda10, internal journal on /usr/local tyEXT3-fs: mounted filesystem with ordered data mode. pe ext3 (rw,acl,user_xattr) /dev/sda9 on /usr/src type ext3 (rw,acl,user_xattr)kjournald starting. Commit interval 5 seconds /dev/sda10 on EXT3 FS on sdb5, internal journal /misc1 type ext3EXT3-fs: mounted filesystem with ordered data mode. (rw,acl,user_xattr) /dev/sdb5 on /11.1 type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb1, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb1 on /11.1/boot type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb6, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb6 on /11.1/home type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb7, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb7 on /11.1/misc type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb8, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb8 on /11.1/usr/local type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb9, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb9 on /11.1/usr/src type ext3 (rw,acl,user_xattr) kjournald starting. Commit interval 5 seconds EXT3 FS on sdb10, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdb10 on /11.1/misc1 type ext3 (rw,acl,userkjournald starting. Commit interval 5 seconds _xattr) EXT3 FS on sdc1, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sdc1 on /local type ext3 (rkjournald starting. Commit interval 5 seconds w,acl,user_xattrEXT3 FS on hda1, ) internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/hda1 on /lcrs type ext3 (rw,acl,user_xattr) done Retry device configuration: done Configuring serial ports... /dev/ttyS0 at 0x03f8 (irq = 4) is a 16550A Configured serial ports done fuse init (API version 7.10) Loading fuse module done Mounting fuse control filesystem done Setting current sysctl status from /etc/sysctl.conf net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.rp_filter = 1 fs.inotify.max_user_watches = 65536 net.ipv4.conf.default.promote_secondaries = 1 net.ipv4.conf.all.promote_secondaries = 1 done Mounting securityfs on /sys/kernel/security done ls: cannot access /sys/module/apparmor: No such file or directory ls: cannot access /sys/module/apparmor: No such file or directory Loading AppArmor module failed Enabling syn flood protection done Disabling IP forwarding done done Creating /var/log/boot.msg done showconsole: Warning: the ioctl TIOCGDEV is not known by the kernel Activating remaining swap-devices in /etc/fstab... done Setting up hostname 'harley' done Setting up loopback interface lo lo IP address: 127.0.0.1/8 IP address: 127.0.0.2/8 done System Boot Control: The system has been set up Failed features: boot.apparmor Skipped features: boot.cycle System Boot Control: Running /etc/init.d/boot.local Linking /usr/src/linix to /usr/src/linux-2.6.28.3-250Hz No rtom kernel driver found in /lib/modules/2.6.28.3-250Hz/misc kernel.shmmax = 81943040 done INIT: Entering runlevel: 5 Boot logging started on /dev/ttyS0(/dev/console) at Fri Feb 20 09:27:00 2009 Master Resource Control: previous runlevel: N, switching to runlevel: 5 mkdir: cannot create directory `/dev/cpuset': File exists mount: cpuset already mounted or /dev/cpuset busy mount: according to mtab, cpuset is already mounted on /dev/cpuset acpid: starting up Starting resource manager done Starting acpid done Initializing random number generator done acpid: 1 rule loaded Starting D-Bus daemonStarting syslog services done done Starting ConsoleKit done NET: Registered protocol family 10 lo: Disabled Privacy Extensions ip6_tables: (C) 2000-2006 Netfilter Core Team Loading CPUFreq modules (CPUFreq not supported) Starting HAL daemonip_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. Starting Firewall Initialization (phase 1 of 2) done done Setting up network interfaces: lo lo IP address: 127.0.0.1/8 IP address: 127.0.0.2/8 done eth0 device: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller (rev 13) eth0 IP address: 10.10.10.100/24 done eth1 device: Intel Corporation 82572EI Gigabit Ethernet Controller (Copper) (rev 06) eth1 IP address: 192.168.10.100/24 done Waiting for mandatory devices: eth2 eth3 __NSC__ 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 eth2 No interface found failed eth3 No interface found failed Setting up service network . . . . . . . . . . . . . . failed Starting service kdm done Mount CIFS File Systems unused VMware Server is installed, but it has not been (correctly) configured for the running kernel. To (re-)configure it, invoke the following command: /usr/bin/vmware-config.pl. Starting RPC portmap daemon done Loading Module rfm2g. ========================================================= COPYRIGHT NOTICE Copyright (C) 2002, 2004 GE Fanuc Embedded Systems, Inc. International Copyright Secured. All Rights Reserved. ========================================================= cat: /proc/rfm2g: No such file or directory /etc/init.d/rfm2g_init: line 84: [: 0: unary operator expected chmod: cannot access `/dev/rfm2g[0-4]': No such file or directory failed Starting auditd done Starting SSH daemon done Starting cupsd done Starting Avahi daemon. done Starting Avahi DNS Configuration daemon done Initializing gpib boards FATAL: Module tnt4882 not found. failed to open device file '/dev/gpib0' main: No such file or directory failed to open device file '/dev/gpib1' main: No such file or directory failed Loading keymap i386/qwerty/us.map.gz done Clearing PCIRMS Sram Memory prm_clear_sram: prm_mmap_open failed: No such device PCIRMS Board 0 SRAM Cleared with option local done Loading compose table latin1.add done Start Unicode mode done Loading console font lat9w-16.psfu -m trivial G0:loadable done ntpd: time slew +0.025589s Starting network time protocol daemon (NTPD) done Starting Name Service Cache Daemon done Starting mail service (Postfix) done Starting CRON daemon done Starting Firewall Initialization (phase 2 of 2) SuSEfirewall2: Warning: no default firewall zone defined, assuming 'ext' done done Master Resource Control: runlevel 5 has been reached Failed services in runlevel 5: network vmware gpib rfm2g_init Skipped services in runlevel 5: smbfs prm prm_dmatest prm_healthy splash Offline