| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20090407155120.18020.62933.stgit@t61.ukuu.org.uk>
Date: Tue, 07 Apr 2009 16:52:26 +0100
From: Alan Cox <alan@...rguk.ukuu.org.uk>
To: torvalds@...ux-foundation.org, linux-kernel@...r.kernel.org
Subject: [PATCH 07/11] tty: Blackin CTS/RTS
From: Sonic Zhang <sonic.zhang@...log.com>
Both software emulated and hardware based CTS and RTS are enabled in serial
driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem device
not as a host device. In order to test it under Linux, please nake a
cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@...log.com>
Signed-off-by: Bryan Wu <cooloney@...nel.org>
Signed-off-by: Andrew Morton <akpm@...ux-foundation.org>
Signed-off-by: Alan Cox <alan@...rguk.ukuu.org.uk>
---
.../mach-bf518/include/mach/bfin_serial_5xx.h | 10 +
.../mach-bf527/include/mach/bfin_serial_5xx.h | 10 +
.../mach-bf533/include/mach/bfin_serial_5xx.h | 9 +
.../mach-bf537/include/mach/bfin_serial_5xx.h | 10 +
.../mach-bf538/include/mach/bfin_serial_5xx.h | 10 +
.../mach-bf548/include/mach/bfin_serial_5xx.h | 72 ++++-----
.../mach-bf561/include/mach/bfin_serial_5xx.h | 9 +
drivers/serial/Kconfig | 26 ++-
drivers/serial/bfin_5xx.c | 169 ++++++++++++++------
9 files changed, 209 insertions(+), 116 deletions(-)
diff --git a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
index e21c1c3..0fb2ce5 100644
--- a/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf518/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -87,6 +87,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -125,6 +126,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -140,6 +142,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART0_RX,
+ IRQ_UART0_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART0_TX,
CH_UART0_RX,
@@ -154,6 +157,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02000,
IRQ_UART1_RX,
+ IRQ_UART1_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART1_TX,
CH_UART1_RX,
diff --git a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
index d2b160c..a625659 100644
--- a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -87,6 +87,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -125,6 +126,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -140,6 +142,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART0_RX,
+ IRQ_UART0_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART0_TX,
CH_UART0_RX,
@@ -154,6 +157,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02000,
IRQ_UART1_RX,
+ IRQ_UART1_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART1_TX,
CH_UART1_RX,
diff --git a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
index 70356dd..a3789d7 100644
--- a/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf533/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -74,6 +74,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -116,6 +117,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -130,6 +132,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART_RX,
+ IRQ_UART_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART_TX,
CH_UART_RX,
diff --git a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
index d46fc4f..b86662f 100644
--- a/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf537/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -87,6 +87,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -124,6 +125,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -139,6 +141,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART0_RX,
+ IRQ_UART0_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART0_TX,
CH_UART0_RX,
@@ -153,6 +156,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02000,
IRQ_UART1_RX,
+ IRQ_UART1_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART1_TX,
CH_UART1_RX,
diff --git a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
index 3c2811e..c536551 100644
--- a/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf538/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -87,6 +87,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -125,6 +126,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -140,6 +142,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART0_RX,
+ IRQ_UART0_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART0_TX,
CH_UART0_RX,
@@ -154,6 +157,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02000,
IRQ_UART1_RX,
+ IRQ_UART1_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART1_TX,
CH_UART1_RX,
diff --git a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
index 388e232..2d1b5fa 100644
--- a/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf548/include/mach/bfin_serial_5xx.h
@@ -46,41 +46,27 @@
#define UART_PUT_CHAR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_THR),v)
#define UART_PUT_DLL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLL),v)
#define UART_SET_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER_SET),v)
-#define UART_CLEAR_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER_CLEAR),v)
+#define UART_CLEAR_IER(uart,v) bfin_write16(((uart)->port.membase + OFFSET_IER_CLEAR),v)
#define UART_PUT_DLH(uart,v) bfin_write16(((uart)->port.membase + OFFSET_DLH),v)
#define UART_PUT_LSR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_LSR),v)
#define UART_PUT_LCR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_LCR),v)
#define UART_CLEAR_LSR(uart) bfin_write16(((uart)->port.membase + OFFSET_LSR), -1)
#define UART_PUT_GCTL(uart,v) bfin_write16(((uart)->port.membase + OFFSET_GCTL),v)
#define UART_PUT_MCR(uart,v) bfin_write16(((uart)->port.membase + OFFSET_MCR),v)
+#define UART_CLEAR_SCTS(uart) bfin_write16(((uart)->port.membase + OFFSET_MSR),SCTS)
#define UART_SET_DLAB(uart) /* MMRs not muxed on BF54x */
#define UART_CLEAR_DLAB(uart) /* MMRs not muxed on BF54x */
#define UART_GET_CTS(x) (UART_GET_MSR(x) & CTS)
-#define UART_SET_RTS(x) (UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS))
-#define UART_CLEAR_RTS(x) (UART_PUT_MCR(x, UART_GET_MCR(x) & ~MRTS))
+#define UART_DISABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) & ~(ARTS|MRTS))
+#define UART_ENABLE_RTS(x) UART_PUT_MCR(x, UART_GET_MCR(x) | MRTS | ARTS)
#define UART_ENABLE_INTS(x, v) UART_SET_IER(x, v)
#define UART_DISABLE_INTS(x) UART_CLEAR_IER(x, 0xF)
-#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART2_CTSRTS)
-# define CONFIG_SERIAL_BFIN_CTSRTS
-
-# ifndef CONFIG_UART0_CTS_PIN
-# define CONFIG_UART0_CTS_PIN -1
-# endif
-
-# ifndef CONFIG_UART0_RTS_PIN
-# define CONFIG_UART0_RTS_PIN -1
-# endif
-
-# ifndef CONFIG_UART2_CTS_PIN
-# define CONFIG_UART2_CTS_PIN -1
-# endif
-
-# ifndef CONFIG_UART2_RTS_PIN
-# define CONFIG_UART2_RTS_PIN -1
-# endif
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS) || \
+ defined(CONFIG_BFIN_UART2_CTSRTS) || defined(CONFIG_BFIN_UART3_CTSRTS)
+# define CONFIG_SERIAL_BFIN_HARD_CTSRTS
#endif
#define BFIN_UART_TX_FIFO_SIZE 2
@@ -91,6 +77,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
int tx_count;
@@ -101,23 +88,24 @@ struct bfin_serial_port {
unsigned int rx_dma_channel;
struct work_struct tx_dma_workqueue;
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct timer_list cts_timer;
- int cts_pin;
- int rts_pin;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ int scts;
+ int cts_pin;
+ int rts_pin;
#endif
};
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- int uart_cts_pin;
- int uart_rts_pin;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ int uart_cts_pin;
+ int uart_rts_pin;
#endif
};
@@ -126,13 +114,14 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART0_RX,
+ IRQ_UART0_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART0_TX,
CH_UART0_RX,
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- CONFIG_UART0_CTS_PIN,
- CONFIG_UART0_RTS_PIN,
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ 0,
+ 0,
#endif
},
#endif
@@ -140,13 +129,14 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02000,
IRQ_UART1_RX,
+ IRQ_UART1_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART1_TX,
CH_UART1_RX,
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- 0,
- 0,
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ GPIO_PE10,
+ GPIO_PE9,
#endif
},
#endif
@@ -154,13 +144,14 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC02100,
IRQ_UART2_RX,
+ IRQ_UART2_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART2_TX,
CH_UART2_RX,
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- CONFIG_UART2_CTS_PIN,
- CONFIG_UART2_RTS_PIN,
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ 0,
+ 0,
#endif
},
#endif
@@ -168,13 +159,14 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC03100,
IRQ_UART3_RX,
+ IRQ_UART3_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART3_TX,
CH_UART3_RX,
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- 0,
- 0,
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ GPIO_PB3,
+ GPIO_PB2,
#endif
},
#endif
diff --git a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
index d0469e3..a1b5087 100644
--- a/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
+++ b/arch/blackfin/mach-bf561/include/mach/bfin_serial_5xx.h
@@ -53,9 +53,9 @@
#define UART_SET_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
#define UART_CLEAR_DLAB(uart) do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
-#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
-#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
-#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_GET_CTS(x) (!gpio_get_value(x->cts_pin))
+#define UART_DISABLE_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_ENABLE_RTS(x) gpio_set_value(x->rts_pin, 0)
#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
@@ -74,6 +74,7 @@
struct bfin_serial_port {
struct uart_port port;
unsigned int old_status;
+ int status_irq;
unsigned int lsr;
#ifdef CONFIG_SERIAL_BFIN_DMA
int tx_done;
@@ -116,6 +117,7 @@ static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
struct bfin_serial_res {
unsigned long uart_base_addr;
int uart_irq;
+ int uart_status_irq;
#ifdef CONFIG_SERIAL_BFIN_DMA
unsigned int uart_tx_dma_channel;
unsigned int uart_rx_dma_channel;
@@ -130,6 +132,7 @@ struct bfin_serial_res bfin_serial_resource[] = {
{
0xFFC00400,
IRQ_UART_RX,
+ IRQ_UART_ERROR,
#ifdef CONFIG_SERIAL_BFIN_DMA
CH_UART_TX,
CH_UART_RX,
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index d89972b..f2e5736 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -734,7 +734,7 @@ config BFIN_UART0_CTSRTS
config UART0_CTS_PIN
int "UART0 CTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 23
help
The default pin is GPIO_GP7.
@@ -742,7 +742,7 @@ config UART0_CTS_PIN
config UART0_RTS_PIN
int "UART0 RTS pin"
- depends on BFIN_UART0_CTSRTS
+ depends on BFIN_UART0_CTSRTS && !BF548
default 22
help
The default pin is GPIO_GP6.
@@ -763,14 +763,14 @@ config BFIN_UART1_CTSRTS
config UART1_CTS_PIN
int "UART1 CTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART1_RTS_PIN
int "UART1 RTS pin"
- depends on BFIN_UART1_CTSRTS && !BF54x
+ depends on BFIN_UART1_CTSRTS && !BF548
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
@@ -790,14 +790,14 @@ config BFIN_UART2_CTSRTS
config UART2_CTS_PIN
int "UART2 CTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
config UART2_RTS_PIN
int "UART2 RTS pin"
- depends on BFIN_UART2_CTSRTS
+ depends on BFIN_UART2_CTSRTS && !BF548
default -1
help
Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
@@ -815,6 +815,20 @@ config BFIN_UART3_CTSRTS
Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
signal.
+config UART3_CTS_PIN
+ int "UART3 CTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART3_RTS_PIN
+ int "UART3 RTS pin"
+ depends on BFIN_UART3_CTSRTS && !BF548
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && (ARCH_IMX || ARCH_MXC)
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index fbbddb9..18ba812 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -72,6 +72,63 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
static void bfin_serial_reset_irda(struct uart_port *port);
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ /* CTS PIN is negative assertive. */
+ if (UART_GET_CTS(uart))
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ /* RTS PIN is negative assertive. */
+ if (mctrl & TIOCM_RTS)
+ UART_ENABLE_RTS(uart);
+ else
+ UART_DISABLE_RTS(uart);
+}
+
+/*
+ * Handle any change of modem status signal.
+ */
+static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned int status;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ uart->scts = 1;
+ UART_CLEAR_SCTS(uart);
+ UART_CLEAR_IER(uart, EDSSI);
+#endif
+
+ return IRQ_HANDLED;
+}
+#else
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+#endif
+
/*
* interrupts are disabled on entry
*/
@@ -108,6 +165,13 @@ static void bfin_serial_start_tx(struct uart_port *port)
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
struct tty_struct *tty = uart->port.info->port.tty;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
/*
* To avoid losting RX interrupt, we reset IR function
* before sending data.
@@ -303,6 +367,12 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
@@ -433,6 +503,13 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
struct bfin_serial_port *uart = dev_id;
struct circ_buf *xmit = &uart->port.info->xmit;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
disable_dma(uart->tx_dma_channel);
@@ -481,53 +558,6 @@ static unsigned int bfin_serial_tx_empty(struct uart_port *port)
return 0;
}
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->cts_pin < 0)
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
- if (UART_GET_CTS(uart))
- return TIOCM_DSR | TIOCM_CAR;
- else
-#endif
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->rts_pin < 0)
- return;
-
- if (mctrl & TIOCM_RTS)
- UART_CLEAR_RTS(uart);
- else
- UART_SET_RTS(uart);
-#endif
-}
-
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
-/*
- * Handle any change of modem status signal.
- */
-static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
-{
- struct bfin_serial_port *uart = dev_id;
- unsigned int status;
-
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
-
- return IRQ_HANDLED;
-}
-#endif
-
-/*
- * Interrupts are always disabled.
- */
static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
@@ -660,6 +690,28 @@ static int bfin_serial_startup(struct uart_port *port)
gpio_direction_output(uart->rts_pin, 0);
}
#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (request_irq(uart->status_irq,
+ bfin_serial_mctrl_cts_int,
+ IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
+ pr_info("Unable to attach BlackFin UART Modem \
+ Status interrupt.\n");
+ }
+
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->cts_pin, 1);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+
+ /* CTS RTS PINs are negative assertive. */
+ UART_PUT_MCR(uart, ACTS);
+ UART_SET_IER(uart, EDSSI);
+#endif
+
UART_SET_IER(uart, ERBFI);
return 0;
}
@@ -694,12 +746,20 @@ static void bfin_serial_shutdown(struct uart_port *port)
free_irq(uart->port.irq+1, uart);
#endif
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
if (uart->cts_pin >= 0)
free_irq(gpio_to_irq(uart->cts_pin), uart);
if (uart->rts_pin >= 0)
gpio_free(uart->rts_pin);
-# endif
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->cts_pin >= 0)
+ gpio_free(uart->cts_pin);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+ if (UART_GET_IER(uart) && EDSSI)
+ free_irq(uart->status_irq, uart);
+#endif
}
static void
@@ -1009,6 +1069,8 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_base_addr;
bfin_serial_ports[i].port.irq =
bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].status_irq =
+ bfin_serial_resource[i].uart_status_irq;
bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
#ifdef CONFIG_SERIAL_BFIN_DMA
bfin_serial_ports[i].tx_done = 1;
@@ -1019,7 +1081,8 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
@@ -1082,7 +1145,8 @@ bfin_serial_console_setup(struct console *co, char *options)
int baud = 57600;
int bits = 8;
int parity = 'n';
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
int flow = 'r';
# else
int flow = 'n';
@@ -1279,7 +1343,8 @@ static int bfin_serial_remove(struct platform_device *dev)
continue;
uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
bfin_serial_ports[i].port.dev = NULL;
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
gpio_free(bfin_serial_ports[i].cts_pin);
gpio_free(bfin_serial_ports[i].rts_pin);
#endif
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists