Message-ID: <21d7e9970907152016u3b213beet9090ee3b34f6d8b1@mail.gmail.com>
Date:	Thu, 16 Jul 2009 13:16:02 +1000
From:	Dave Airlie <airlied@...il.com>
To:	Michael Cree <mcree@...on.net.nz>
Cc:	linux-alpha@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: Re: Kernel 2.6.30.1 Oops on Alpha Architecture when starting Xserver

On Wed, Jul 15, 2009 at 8:41 PM, Michael Cree<mcree@...on.net.nz> wrote:
> Kernel Oops on Alpha Architecture when starting the Xserver.
>
> Whenever I start the Xserver, version 1.6.2 from Debain Unstable, I get a
> kernel oops report and the computer crashes hard; no ping response, hitting
> the reset button to return to SRM fails.  Has caused corruption on disc
> partitions on some crashes.  This occurs with kernels 2.6.30, 2.6.30.1 and
> also a patched version of 2.6.29.x (patched so that I get PCI resource files
> under sysfs).
>
> The kernel oops is:

So its a machine check,

Well X is trying to post the graphics card you have installed, and the machine
is falling over when it does it.

I'm not really sure what you can do in that case, not posting the GPU would
probably end up with no working gpu either.

Dave.


>
> Unable to handle kernel paging request at virtual address 000000000000000c
> Xorg(1940): Oops 0
> pc = [<fffffc000031e634>]  ra = [<fffffc000031570c>]  ps = 0007    Not
> tainted
> pc is at cia_machine_check+0x84/0x570
> ra is at do_entInt+0x16c/0x1d0
> v0 = 0000000000000001  t0 = 0000000000000001  t1 = fffffc000071a250
> t2 = 0000000000000001  t3 = 0000000000000031  t4 = 3a00000000000000
> t5 = 0000000000000004  t6 = 000000000000000f  t7 = fffffc0021c0c000
> s0 = fffffc00006ed2d8  s1 = 0000000000000000  s2 = fffffc0021c0fee8
> s3 = 000000011ff016fc  s4 = 000000011ff016f4  s5 = fffffc0000006068
> s6 = 0000000000000660
> a0 = 0000000000000001  a1 = 0000000000000000  a2 = fffffc0000006068
> a3 = 0000000000000000  a4 = 0000000100000010  a5 = 000000012029c0a0
> t8 = 0000000000000010  t9 = 00000001200c0b98  t10= 0000000000000000
> t11= 000000000000000a  pv = fffffc000031e5b0  at = 0000000000000006
> gp = fffffc00007192f0  sp = fffffc0021c0fe88
> Disabling lock debugging due to kernel taint
> Trace:
> [<fffffc000031570c>] do_entInt+0x16c/0x1d0
> [<fffffc0000310c80>] ret_from_sys_call+0x0/0x10
> [<fffffc0000310720>] entInt+0x0/0x80
>
> Code: 207f0660  41e305a3  2a620000  426015a1  44230001  e420000f <a031000c>
> 47ff0413
>
>
> On one crash there was a trace of the Xorg.log file left intact ending with
> the following lines:
>
> (II) RADEON(0): Attempting to read un-POSTed bios
> (II) RADEON(0): ATOM BIOS detected
> (II) RADEON(0): ATOM BIOS Rom:
>       SubsystemVendorID: 0x2232 SubsystemID: 0x1787
>       IOBaseAddress: 0x0000
>       Filename: 72319EAA.QEA
>       BIOS Bootup Message:   HD2400 GDDR2_32MX16 64BIT 256MB 72319EAA.QEA
>                             (II) RADEON(0): Framebuffer space used by
> Firmware (kb): 0
> (WW) RADEON(0): rhdAtomGetFbBaseAndSize: AtomBIOS specified VRAM scratch
> space size invalid
> (II) RADEON(0):  default to: 20480
> (II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory
> instead
> (II) RADEON(0): Default Engine Clock: 525000
> (II) RADEON(0): Default Memory Clock: 400000
> (II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 1200000
> (II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 0
> (II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
> (II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
> (II) RADEON(0): Maximum Pixel Clock: 400000
> (II) RADEON(0): Reference Clock: 27000
> (II) RADEON(0): Default Engine Clock: 525000
> (II) RADEON(0): Default Memory Clock: 400000
> (II) RADEON(0): Calling ASIC Init
> [Xorg.log ends here]
>
>
> Other machine info follows:
>
> aleph:~# cat /proc/version
> Linux version 2.6.30.1-miata (mjc@...ha) (gcc version 4.2.4 (Debian
> 4.2.4-6)) #1 Fri Jul 3 22:54:36 NZST 2009
>
> aleph:~# cat /proc/cpuinfo
> cpu            : Alpha
> cpu model        : EV56
> cpu variation        : 7
> cpu revision        : 0
> cpu serial number    :
> system type        : Miata
> system variation    : 0
> system revision        : 0
> system serial number    :
> cycle frequency [Hz]    : 600000000
> timer frequency [Hz]    : 1024.00
> page size [bytes]    : 8192
> phys. address bits    : 40
> max. addr. space #    : 127
> BogoMIPS        : 1187.96
> kernel unaligned acc    : 0 (pc=0,va=0)
> user unaligned acc    : 0 (pc=0,va=0)
> platform string        : Digital Personal WorkStation 600au
> cpus detected        : 1
> L1 Icache        : 8K, 1-way, 32b line
> L1 Dcache        : 8K, 1-way, 32b line
> L2 cache        : 96K, 3-way, 64b line
> L3 cache        : 2048K, 1-way, 64b line
>
> aleph:~# cat /proc/modules
> ipv6 331224 22 - Live 0xfffffffc008c2000
> loop 18872 0 - Live 0xfffffffc00812000
> snd_es18xx 40484 0 - Live 0xfffffffc007f0000
> ohci_hcd 26048 0 - Live 0xfffffffc00788000
> ehci_hcd 40004 0 - Live 0xfffffffc00764000
> ide_cd_mod 36336 0 - Live 0xfffffffc0073c000
> cdrom 44000 1 ide_cd_mod, Live 0xfffffffc006fc000
> snd_hda_codec_atihdmi 4616 1 - Live 0xfffffffc006d8000
> snd_hda_intel 31184 0 - Live 0xfffffffc006be000
> snd_cmipci 42152 0 - Live 0xfffffffc00696000
> snd_opl3_lib 13288 2 snd_es18xx,snd_cmipci, Live 0xfffffffc00672000
> snd_hwdep 9760 1 snd_opl3_lib, Live 0xfffffffc0065a000
> snd_mpu401_uart 9488 2 snd_es18xx,snd_cmipci, Live 0xfffffffc00642000
> snd_seq_midi 8768 0 - Live 0xfffffffc0062a000
> snd_seq_midi_event 8032 1 snd_seq_midi, Live 0xfffffffc00614000
> sata_sil 11328 0 - Live 0xfffffffc005fe000
> snd_hda_codec 72498 2 snd_hda_codec_atihdmi,snd_hda_intel, Live
> 0xfffffffc005de000
> snd_rawmidi 26657 2 snd_mpu401_uart,snd_seq_midi, Live 0xfffffffc005a6000
> snd_pcm 77689 4 snd_es18xx,snd_hda_intel,snd_cmipci,snd_hda_codec, Live
> 0xfffffffc00576000
> snd_seq 67568 2 snd_seq_midi,snd_seq_midi_event, Live 0xfffffffc00534000
> snd_timer 25064 3 snd_opl3_lib,snd_pcm,snd_seq, Live 0xfffffffc004fe000
> snd_seq_device 8808 4 snd_opl3_lib,snd_seq_midi,snd_rawmidi,snd_seq, Live
> 0xfffffffc004de000
> snd 72216 12
> snd_es18xx,snd_hda_intel,snd_cmipci,snd_opl3_lib,snd_hwdep,snd_mpu401_uart,snd_hda_codec,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device,
> Live 0xfffffffc004b8000
> snd_page_alloc 11200 2 snd_hda_intel,snd_pcm, Live 0xfffffffc00484000
> soundcore 7712 1 snd, Live 0xfffffffc0046e000
> libata 191292 1 sata_sil, Live 0xfffffffc0042a000
> evdev 12896 1 - Live 0xfffffffc003b6000
> pcspkr 3088 0 - Live 0xfffffffc0039e000
> usbcore 168612 3 ohci_hcd,ehci_hcd, Live 0xfffffffc00364000
> cy82c693 4552 0 - Live 0xfffffffc002f0000
> tulip 56856 0 - Live 0xfffffffc002d0000
> ide_pci_generic 5132 0 - Live 0xfffffffc002a6000
>
> aleph:~# cat /proc/ioports
> 0000-001f : dma1
> 0020-003f : pic1
> 0040-005f : timer
> 0060-006f : keyboard
> 0070-0080 : rtc
> 00a0-00bf : pic2
> 00c0-00df : dma2
> 0170-0177 : 0000:00:07.2
>  0170-0177 : cy82c693
> 01f0-01f7 : 0000:00:07.1
>  01f0-01f7 : cy82c693
> 0220-022f : ES18xx
> 02f8-02ff : serial
> 0330-0331 : MPU401 UART
> 0376-0376 : 0000:00:07.2
>  0376-0376 : cy82c693
> 03c0-03df : vga+
> 03f2-03f2 : floppy
> 03f4-03f5 : floppy
> 03f6-03f6 : 0000:00:07.1
>  03f6-03f6 : cy82c693
> 03f7-03f7 : floppy
> 03f8-03ff : serial
> 8000-8fff : PCI Bus 0000:01
>  8000-80ff : 0000:01:00.0
> 9000-9fff : PCI Bus 0000:02
>  9000-90ff : 0000:02:04.0
>  9400-94ff : 0000:02:0a.0
>   9400-94ff : CMI8738-MC6
>  9800-980f : 0000:02:08.0
>  9810-9817 : 0000:02:08.0
>  9818-981f : 0000:02:08.0
>  9820-9823 : 0000:02:08.0
>  9824-9827 : 0000:02:08.0
> a000-a07f : 0000:00:03.0
>  a000-a07f : tulip
> a080-a08f : 0000:00:07.1
>  a080-a08f : cy82c693
>
> aleph:~# car /proc/iomem
> 09000000-090fffff : PCI Bus 0000:01
>  09000000-0900ffff : 0000:01:00.0
>  09010000-09013fff : 0000:01:00.1
>   09010000-09013fff : ICH HD audio
> 09100000-091fffff : PCI Bus 0000:02
>  09100000-09100fff : 0000:02:04.0
>  09101000-091011ff : 0000:02:08.0
>   09101000-091011ff : sata_sil
> 09200000-092fffff : PCI Bus 0000:02
>  09200000-0927ffff : 0000:02:08.0
>  09280000-0928ffff : 0000:02:04.0
> 09300000-0933ffff : 0000:00:03.0
> 09340000-0934ffff : 0000:00:07.2
>  09340000-0934ffff : cy82c693
> 09350000-09350fff : 0000:00:07.3
>  09350000-09350fff : ohci_hcd
> 09351000-0935107f : 0000:00:03.0
>  09351000-0935107f : tulip
> 10000000-27ffffff : PCI Bus 0000:01
>  10000000-1fffffff : 0000:01:00.0
>  20000000-2001ffff : 0000:01:00.0
>
> aleph:~# lspci -vvv
> 00:03.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43
> (rev 30)
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 255 (5000ns min, 10000ns max), Cache Line Size: 64 bytes
>   Interrupt: pin A routed to IRQ 24
>   Region 0: I/O ports at a000 [size=128]
>   Region 1: Memory at 09351000 (32-bit, non-prefetchable) [size=128]
>   Expansion ROM at 09300000 [disabled] [size=256K]
>   Kernel driver in use: tulip
>   Kernel modules: tulip
>
> 00:07.0 ISA bridge: Contaq Microsystems 82c693
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 0
>   Kernel modules: cy82c693
>
> 00:07.1 IDE interface: Contaq Microsystems 82c693 (prog-if 80 [Master])
>   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 0
>   Interrupt: pin A routed to IRQ 0
>   Region 0: I/O ports at 01f0 [size=8]
>   Region 1: I/O ports at 03f4 [size=1]
>   Region 4: I/O ports at a080 [size=16]
>   Kernel driver in use: Cypress_IDE
>   Kernel modules: cy82c693, ide-pci-generic
>
> 00:07.2 IDE interface: Contaq Microsystems 82c693 (prog-if 00 [])
>   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 0
>   Interrupt: pin B routed to IRQ 0
>   Region 0: I/O ports at 0170 [size=8]
>   Region 1: I/O ports at 0374 [size=1]
>   Region 4: Memory at 09340000 (32-bit, non-prefetchable) [disabled]
> [size=64K]
>   Kernel modules: cy82c693, ide-pci-generic
>
> 00:07.3 USB Controller: Contaq Microsystems 82c693 (prog-if 10 [OHCI])
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 248
>   Interrupt: pin A routed to IRQ 10
>   Region 0: Memory at 09350000 (32-bit, non-prefetchable) [size=4K]
>   Kernel driver in use: ohci_hcd
>   Kernel modules: cy82c693, ohci-hcd
>
> 00:0c.0 PCI bridge: PLX Technology, Inc. PEX8112 x1 Lane PCI Express-to-PCI
> Bridge (rev aa) (prog-if 00 [Normal decode])
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
>   Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 255, Cache Line Size: 64 bytes
>   Bus: primary=00, secondary=01, subordinate=01, sec-latency=255
>   I/O behind bridge: 00008000-00008fff
>   Memory behind bridge: 09000000-090fffff
>   Prefetchable memory behind bridge: 10000000-27ffffff
>   Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ <SERR- <PERR-
>   BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>       PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>   Capabilities: [40] Power Management version 2
>       Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
> PME(D0+,D1+,D2-,D3hot+,D3cold-)
>       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>   Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
>       Address: 0000000000000000  Data: 0000
>   Capabilities: [60] Express (v1) PCI/PCI-X to PCI-Express Bridge, MSI 00
>       DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1
> <1us
>           ExtTag- RBE- FLReset-
>       DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>           RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
>           MaxPayload 128 bytes, MaxReadReq 512 bytes
>       DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
>       LnkCap:    Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
> <1us, L1 <16us
>           ClockPM- Surprise- LLActRep- BwNot-
>       LnkCtl:    ASPM Disabled; Disabled- Retrain- CommClk-
>           ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>       LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive-
> BWMgmt- ABWMgmt-
>
> 00:14.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 02)
> (prog-if 00 [Normal decode])
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 255, Cache Line Size: 64 bytes
>   Bus: primary=00, secondary=02, subordinate=02, sec-latency=255
>   I/O behind bridge: 00009000-00009fff
>   Memory behind bridge: 09100000-091fffff
>   Prefetchable memory behind bridge: 0000000009200000-00000000092fffff
>   Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- <SERR- <PERR-
>   BridgeCtl: Parity- SERR- NoISA- VGA- MAbort+ >Reset- FastB2B-
>       PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>
> 01:00.0 VGA compatible controller: ATI Technologies Inc RV 610LE PCI [Radeon
> HD 2400] (prog-if 00 [VGA controller])
>   Subsystem: Device 2232:1787
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 0, Cache Line Size: 64 bytes
>   Interrupt: pin A routed to IRQ 32
>   Region 0: Memory at 10000000 (64-bit, prefetchable) [size=256M]
>   Region 2: Memory at 09000000 (64-bit, non-prefetchable) [size=64K]
>   Region 4: I/O ports at 8000 [size=256]
>   Expansion ROM at 20000000 [disabled] [size=128K]
>   Capabilities: [50] Power Management version 3
>       Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>   Capabilities: [58] Express (v1) Legacy Endpoint, MSI 00
>       DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
> unlimited
>           ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
>       DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>           RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>           MaxPayload 128 bytes, MaxReadReq 128 bytes
>       DevSta:    CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
>       LnkCap:    Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0
> <64ns, L1 <1us
>           ClockPM- Surprise- LLActRep- BwNot-
>       LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
>           ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>       LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
>   Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
>       Address: 0000000000000000  Data: 0000
>   Capabilities: [100] #1002
>   Capabilities: [aa1] #ffff
>
> 01:00.1 Audio device: ATI Technologies Inc RV610 audio device [Radeon HD
> 2400 PRO]
>   Subsystem: Device 2232:aa10
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx+
>   Latency: 0, Cache Line Size: 64 bytes
>   Interrupt: pin B routed to IRQ 33
>   Region 0: Memory at 09010000 (64-bit, non-prefetchable) [size=16K]
>   Capabilities: [50] Power Management version 3
>       Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>   Capabilities: [58] Express (v1) Legacy Endpoint, MSI 00
>       DevCap:    MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
> unlimited
>           ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
>       DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
>           RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>           MaxPayload 128 bytes, MaxReadReq 128 bytes
>       DevSta:    CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
>       LnkCap:    Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0
> <64ns, L1 <1us
>           ClockPM- Surprise- LLActRep- BwNot-
>       LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
>           ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>       LnkSta:    Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
> BWMgmt- ABWMgmt-
>   Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
>       Address: 0000000000000000  Data: 0000
>   Capabilities: [100] #1002
>   Capabilities: [aa1] #ffff
>   Kernel driver in use: HDA Intel
>   Kernel modules: snd-hda-intel
>
> 02:04.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev
> 05)
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 248, Cache Line Size: 64 bytes
>   Interrupt: pin A routed to IRQ 27
>   Region 0: I/O ports at 9000 [size=256]
>   Region 1: Memory at 09100000 (32-bit, non-prefetchable) [size=4K]
>   Expansion ROM at 09280000 [disabled] [size=64K]
>   Kernel driver in use: qla1280
>
> 02:08.0 RAID bus controller: Silicon Image, Inc. SiI 3112
> [SATALink/SATARaid] Serial ATA Controller (rev 02)
>   Subsystem: Silicon Image, Inc. SiI 3112 SATARaid Controller
>   Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 240, Cache Line Size: 64 bytes
>   Interrupt: pin A routed to IRQ 36
>   Region 0: I/O ports at 9810 [size=8]
>   Region 1: I/O ports at 9820 [size=4]
>   Region 2: I/O ports at 9818 [size=8]
>   Region 3: I/O ports at 9824 [size=4]
>   Region 4: I/O ports at 9800 [size=16]
>   Region 5: Memory at 09101000 (32-bit, non-prefetchable) [size=512]
>   Expansion ROM at 09200000 [disabled] [size=512K]
>   Capabilities: [60] Power Management version 2
>       Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
>   Kernel driver in use: sata_sil
>   Kernel modules: sata_sil
>
> 02:0a.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
>   Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
>   Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B- DisINTx-
>   Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR- INTx-
>   Latency: 255 (500ns min, 6000ns max)
>   Interrupt: pin A routed to IRQ 44
>   Region 0: I/O ports at 9400 [size=256]
>   Capabilities: [c0] Power Management version 2
>       Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>       Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>   Kernel driver in use: C-Media PCI
>   Kernel modules: snd-cmipci
>
> Cheerz
> Michael.
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at  http://www.tux.org/lkml/
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists