| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20090726080212.GA24365@dtor-d630.eng.vmware.com>
Date: Sun, 26 Jul 2009 01:02:12 -0700
From: Dmitry Torokhov <dmitry.torokhov@...il.com>
To: Richard Röjfors
<richard.rojfors.ext@...ean-labs.com>
Cc: linux-input@...r.kernel.org,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>,
Andrew Morton <akpm@...ux-foundation.org>,
kwangwoo.lee@...il.com,
Thierry Reding <thierry.reding@...onic-design.de>,
Trilok Soni <soni.trilok@...il.com>
Subject: Re: [PATCH 2/2] tsc2007: reduced number of I2C transfers
On Fri, Jul 24, 2009 at 09:37:27PM +0200, Richard Röjfors wrote:
> On 7/24/09 8:00 PM, Dmitry Torokhov wrote:
>> On Fri, Jul 24, 2009 at 06:14:37PM +0200, Richard Röjfors wrote:
>>> Decreases the number of I2C transactions transferred by the driver.
>>> During probe we don't need to ask for the coordinates from the controller.
>>> When polling the controller we don't need to power down and enable IRQ
>>> if we are going to poll again.
>>>
>>> Signed-off-by: Richard Röjfors<richard.rojfors.ext@...ean-labs.com>
>>> ---
>>> Index: linux-2.6.31-rc2/drivers/input/touchscreen/tsc2007.c
>>> ===================================================================
>>> --- linux-2.6.31-rc2/drivers/input/touchscreen/tsc2007.c (revision 1040)
>>> +++ linux-2.6.31-rc2/drivers/input/touchscreen/tsc2007.c (revision 1053)
>>> @@ -178,6 +178,12 @@
>>> ts->penstate = PEN_STATE_UP;
>>> }
>>>
>>> +static void tsc2007_power_down(struct tsc2007 *tsc)
>>> +{
>>> + /* power down */
>>> + tsc2007_xfer(tsc, PWRDOWN);
>>> +}
>>> +
>>> static int tsc2007_read_values(struct tsc2007 *tsc)
>>> {
>>> /* y- still on; turn on only y+ (and ADC) */
>>> @@ -188,11 +194,8 @@
>>>
>>> /* turn y+ off, x- on; we'll use formula #1 */
>>> tsc->tc.z1 = tsc2007_xfer(tsc, READ_Z1);
>>> - tsc->tc.z2 = tsc2007_xfer(tsc, READ_Z2);
>>> + tsc->tc.z2 = tsc2007_xfer(tsc, READ_Z2 | TSC2007_POWER_OFF_IRQ_EN);
>>
>> I think this leaves the controller powered on and with with PENIRQ
>> disabled.
>>
>
> You are right, I think we should leave the patch like below, just get
> rid of the unnecessary read during startup.
>
I modified the patch a bit before applying. In fact there were a few
changes to all the patces so it would be nice if you could take a look
at the 'next' branch of my tree:
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input.git next
Also, I di dnot quite like the logic of the patch making
get_pendown_state callback optional; could you please try the patch
below and let me know of it works for you?
Thanks!
--
Dmitry
Input: tsc2007 - make get_pendown_state platform callback optional
In cases when get_pendown_state callback is not available have
the driver to fallback on pressure calculation to determine if
the pen is up.
Signed-off-by: Dmitry Torokhov <dtor@...l.ru>
---
drivers/input/touchscreen/tsc2007.c | 170 +++++++++++++++++++----------------
1 files changed, 92 insertions(+), 78 deletions(-)
diff --git a/drivers/input/touchscreen/tsc2007.c b/drivers/input/touchscreen/tsc2007.c
index f710af4..ac5e0e8 100644
--- a/drivers/input/touchscreen/tsc2007.c
+++ b/drivers/input/touchscreen/tsc2007.c
@@ -70,7 +70,6 @@ struct tsc2007 {
struct input_dev *input;
char phys[32];
struct delayed_work work;
- struct ts_event tc;
struct i2c_client *client;
@@ -106,51 +105,96 @@ static inline int tsc2007_xfer(struct tsc2007 *tsc, u8 cmd)
return val;
}
-static void tsc2007_send_event(void *tsc)
+static void tsc2007_read_values(struct tsc2007 *tsc, struct ts_event *tc)
{
- struct tsc2007 *ts = tsc;
- u32 rt;
- u16 x, y, z1, z2;
+ /* y- still on; turn on only y+ (and ADC) */
+ tc->y = tsc2007_xfer(tsc, READ_Y);
+
+ /* turn y- off, x+ on, then leave in lowpower */
+ tc->x = tsc2007_xfer(tsc, READ_X);
+
+ /* turn y+ off, x- on; we'll use formula #1 */
+ tc->z1 = tsc2007_xfer(tsc, READ_Z1);
+ tc->z2 = tsc2007_xfer(tsc, READ_Z2);
- x = ts->tc.x;
- y = ts->tc.y;
- z1 = ts->tc.z1;
- z2 = ts->tc.z2;
+ /* Prepare for next touch reading - power down ADC, enable PENIRQ */
+ tsc2007_xfer(tsc, PWRDOWN);
+}
+
+static u32 tsc2007_calculate_pressure(struct tsc2007 *tsc, struct ts_event *tc)
+{
+ u32 rt = 0;
/* range filtering */
- if (x == MAX_12BIT)
- x = 0;
+ if (tc->x == MAX_12BIT)
+ tc->x = 0;
- if (likely(x && z1)) {
+ if (likely(tc->x && tc->z1)) {
/* compute touch pressure resistance using equation #1 */
- rt = z2;
- rt -= z1;
- rt *= x;
- rt *= ts->x_plate_ohms;
- rt /= z1;
+ rt = tc->z2 - tc->z1;
+ rt *= tc->x;
+ rt *= tsc->x_plate_ohms;
+ rt /= tc->z1;
rt = (rt + 2047) >> 12;
- } else
- rt = 0;
-
- /*
- * Sample found inconsistent by debouncing or pressure is beyond
- * the maximum. Don't report it to user space, repeat at least
- * once more the measurement
- */
- if (rt > MAX_12BIT) {
- dev_dbg(&ts->client->dev, "ignored pressure %d\n", rt);
- return;
}
+ return rt;
+}
+
+static void tsc2007_send_up_event(struct tsc2007 *tsc)
+{
+ struct input_dev *input = tsc->input;
+
+ dev_dbg(&tsc->client->dev, "UP\n");
+
+ input_report_key(input, BTN_TOUCH, 0);
+ input_report_abs(input, ABS_PRESSURE, 0);
+ input_sync(input);
+}
+
+static void tsc2007_work(struct work_struct *work)
+{
+ struct tsc2007 *ts =
+ container_of(to_delayed_work(work), struct tsc2007, work);
+ struct ts_event tc;
+ u32 rt;
+
/*
* NOTE: We can't rely on the pressure to determine the pen down
- * state, even this controller has a pressure sensor. The pressure
- * value can fluctuate for quite a while after lifting the pen and
- * in some cases may not even settle at the expected value.
+ * state, even though this controller has a pressure sensor.
+ * The pressure value can fluctuate for quite a while after
+ * lifting the pen and in some cases may not even settle at the
+ * expected value.
*
* The only safe way to check for the pen up condition is in the
- * work function by reading the pen signal state (it's a GPIO and IRQ).
+ * work function by reading the pen signal state (it's a GPIO
+ * and IRQ). Unfortunately such callback is not always available,
+ * in that case we have rely on the pressure anyway.
*/
+ if (ts->get_pendown_state) {
+ if (unlikely(!ts->get_pendown_state())) {
+ tsc2007_send_up_event(ts);
+ ts->pendown = false;
+ goto out;
+ }
+
+ dev_dbg(&ts->client->dev, "pen is still down\n");
+ }
+
+ tsc2007_read_values(ts, &tc);
+
+ rt = tsc2007_calculate_pressure(ts, &tc);
+ if (rt > MAX_12BIT) {
+ /*
+ * Sample found inconsistent by debouncing or pressure is
+ * beyond the maximum. Don't report it to user space,
+ * repeat at least once more the measurement.
+ */
+ dev_dbg(&ts->client->dev, "ignored pressure %d\n", rt);
+ goto out;
+
+ }
+
if (rt) {
struct input_dev *input = ts->input;
@@ -161,68 +205,38 @@ static void tsc2007_send_event(void *tsc)
ts->pendown = true;
}
- input_report_abs(input, ABS_X, x);
- input_report_abs(input, ABS_Y, y);
+ input_report_abs(input, ABS_X, tc.x);
+ input_report_abs(input, ABS_Y, tc.y);
input_report_abs(input, ABS_PRESSURE, rt);
input_sync(input);
dev_dbg(&ts->client->dev, "point(%4d,%4d), pressure (%4u)\n",
- x, y, rt);
- }
-}
-
-static int tsc2007_read_values(struct tsc2007 *tsc)
-{
- /* y- still on; turn on only y+ (and ADC) */
- tsc->tc.y = tsc2007_xfer(tsc, READ_Y);
-
- /* turn y- off, x+ on, then leave in lowpower */
- tsc->tc.x = tsc2007_xfer(tsc, READ_X);
-
- /* turn y+ off, x- on; we'll use formula #1 */
- tsc->tc.z1 = tsc2007_xfer(tsc, READ_Z1);
- tsc->tc.z2 = tsc2007_xfer(tsc, READ_Z2);
-
- /* Prepare for next touch reading - power down ADC, enable PENIRQ */
- tsc2007_xfer(tsc, PWRDOWN);
-
- return 0;
-}
-
-static void tsc2007_work(struct work_struct *work)
-{
- struct tsc2007 *ts =
- container_of(to_delayed_work(work), struct tsc2007, work);
-
- if (unlikely(!ts->get_pendown_state() && ts->pendown)) {
- struct input_dev *input = ts->input;
-
- dev_dbg(&ts->client->dev, "UP\n");
-
- input_report_key(input, BTN_TOUCH, 0);
- input_report_abs(input, ABS_PRESSURE, 0);
- input_sync(input);
+ tc.x, tc.y, rt);
+ } else if (!ts->get_pendown_state && ts->pendown) {
+ /*
+ * We don't have callback to check pendown state, so we
+ * have to assume that since pressure reported is 0 the
+ * pen was lifted up.
+ */
+ tsc2007_send_up_event(ts);
ts->pendown = false;
- enable_irq(ts->irq);
- } else {
- /* pen is still down, continue with the measurement */
- dev_dbg(&ts->client->dev, "pen is still down\n");
-
- tsc2007_read_values(ts);
- tsc2007_send_event(ts);
+ }
+ out:
+ if (ts->pendown)
schedule_delayed_work(&ts->work,
msecs_to_jiffies(TS_POLL_PERIOD));
- }
+ else
+ enable_irq(ts->irq);
}
static irqreturn_t tsc2007_irq(int irq, void *handle)
{
struct tsc2007 *ts = handle;
- if (likely(ts->get_pendown_state())) {
+ if (!ts->get_pendown_state || likely(ts->get_pendown_state())) {
disable_irq_nosync(ts->irq);
schedule_delayed_work(&ts->work,
msecs_to_jiffies(TS_POLL_DELAY));
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists