Add a driver for the the Consumer IR (CIR) functionality of the Winbond WPCD376I chipset (found on e.g. Intel DG45FC motherboards). Changes since the first version: o converted from an ACPI to a PNP driver using a patch provided by Bjorn Helgaas Changes since the second version: o misc fixes to the irqhandler after discovering that the FIFO enforces 16 levels (was a separate patch in the -mm tree) o __devexit annotations o KEY_NUMERIC_[0-9] instead of KEY_[0-9] o EV_MSC/MSC_SCAN instead of "last_scancode" sysfs attr o last three points based on feedback from Dmitry Torokhov Signed-off-by: David Härdeman Reviewed-by: Jesse Barnes Index: linux-2.6/MAINTAINERS =================================================================== --- linux-2.6.orig/MAINTAINERS 2009-08-09 11:32:42.000000000 +0200 +++ linux-2.6/MAINTAINERS 2009-08-09 11:44:35.000000000 +0200 @@ -6448,6 +6448,12 @@ S: Maintained F: drivers/scsi/wd7000.c +WINBOND CIR DRIVER +P: David Härdeman +M: david@hardeman.nu +S: Maintained +F: drivers/input/misc/winbond-cir.c + WIMAX STACK P: Inaky Perez-Gonzalez M: inaky.perez-gonzalez@intel.com Index: linux-2.6/drivers/input/misc/Kconfig =================================================================== --- linux-2.6.orig/drivers/input/misc/Kconfig 2009-08-09 11:32:42.000000000 +0200 +++ linux-2.6/drivers/input/misc/Kconfig 2009-08-11 18:20:41.000000000 +0200 @@ -222,6 +222,22 @@ To compile this driver as a module, choose M here: the module will be called sgi_btns. +config INPUT_WINBOND_CIR + tristate "Winbond IR remote control" + depends on X86 && PNP + select LEDS_CLASS + select BITREVERSE + help + Say Y here if you want to use the IR remote functionality found + in some Winbond SuperI/O chips. Currently only the WPCD376I + chip is supported (included in some Intel Media series motherboards). + + IR Receive and wake-on-IR from suspend and power-off is currently + supported. + + To compile this driver as a module, choose M here: the module will be + called winbond_cir. + config HP_SDC_RTC tristate "HP SDC Real Time Clock" depends on (GSC || HP300) && SERIO Index: linux-2.6/drivers/input/misc/Makefile =================================================================== --- linux-2.6.orig/drivers/input/misc/Makefile 2009-08-09 11:32:42.000000000 +0200 +++ linux-2.6/drivers/input/misc/Makefile 2009-08-13 18:25:06.000000000 +0200 @@ -24,5 +24,6 @@ obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o obj-$(CONFIG_INPUT_UINPUT) += uinput.o +obj-$(CONFIG_INPUT_WINBOND_CIR) += winbond-cir.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_YEALINK) += yealink.o Index: linux-2.6/drivers/input/misc/winbond-cir.c =================================================================== --- /dev/null 1970-01-01 00:00:00.000000000 +0000 +++ linux-2.6/drivers/input/misc/winbond-cir.c 2009-08-13 20:33:06.000000000 +0200 @@ -0,0 +1,1614 @@ +/* + * winbond-cir.c - Driver for the Consumer IR functionality of Winbond + * SuperI/O chips. + * + * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but + * could probably support others (Winbond WEC102X, NatSemi, etc) + * with minor modifications. + * + * Original Author: David Härdeman + * Copyright (C) 2009 David Härdeman + * + * Dedicated to Matilda, my newborn daughter, without whose loving attention + * this driver would have been finished in half the time and with a fraction + * of the bugs. + * + * Written using: + * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel + * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff) + * o DSDT dumps + * + * Supported features: + * o RC6 + * o Wake-On-CIR functionality + * + * To do: + * o Test NEC and RC5 + * + * Left as an exercise for the reader: + * o Learning (I have neither the hardware, nor the need) + * o IR Transmit (ibid) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRVNAME "winbond-cir" + +/* CEIR Wake-Up Registers, relative to data->wbase */ +#define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */ +#define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */ +#define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */ +#define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */ +#define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */ +#define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */ +#define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */ +#define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */ +#define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */ +#define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */ + +/* CEIR Enhanced Functionality Registers, relative to data->ebase */ +#define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */ +#define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */ +#define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */ +#define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */ +#define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */ + +/* SP3 Banked Registers, relative to data->sbase */ +#define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */ + /* Bank 0 */ +#define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */ +#define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */ +#define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */ +#define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */ +#define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */ +#define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */ +#define WBCIR_REG_SP3_LSR 0x05 /* Link Status */ +#define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */ +#define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */ + /* Bank 2 */ +#define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */ +#define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */ +#define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */ +#define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */ +#define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */ +#define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */ + /* Bank 3 */ +#define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */ +#define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */ +#define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */ + /* Bank 4 */ +#define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */ + /* Bank 5 */ +#define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */ + /* Bank 6 */ +#define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */ +#define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */ + /* Bank 7 */ +#define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */ +#define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */ +#define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */ +#define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */ +#define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */ + +/* + * Magic values follow + */ + +/* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_NONE 0x00 +/* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_RX 0x01 +/* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_ERR 0x04 +/* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */ +#define WBCIR_LED_ENABLE 0x80 +/* RX data available bit for WBCIR_REG_SP3_LSR */ +#define WBCIR_RX_AVAIL 0x01 +/* RX disable bit for WBCIR_REG_SP3_ASCR */ +#define WBCIR_RX_DISABLE 0x20 +/* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */ +#define WBCIR_EXT_ENABLE 0x01 +/* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ +#define WBCIR_REGSEL_COMPARE 0x10 +/* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ +#define WBCIR_REGSEL_MASK 0x20 +/* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */ +#define WBCIR_REG_ADDR0 0x00 + +/* Valid banks for the SP3 UART */ +enum wbcir_bank { + WBCIR_BANK_0 = 0x00, + WBCIR_BANK_1 = 0x80, + WBCIR_BANK_2 = 0xE0, + WBCIR_BANK_3 = 0xE4, + WBCIR_BANK_4 = 0xE8, + WBCIR_BANK_5 = 0xEC, + WBCIR_BANK_6 = 0xF0, + WBCIR_BANK_7 = 0xF4, +}; + +/* Supported IR Protocols */ +enum wbcir_protocol { + IR_PROTOCOL_RC5 = 0x0, + IR_PROTOCOL_NEC = 0x1, + IR_PROTOCOL_RC6 = 0x2, +}; + +/* Misc */ +#define WBCIR_NAME "Winbond CIR" +#define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */ +#define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */ +#define IR_KEYPRESS_TIMEOUT 250 /* FIXME: should be per-protocol? */ +#define INVALID_SCANCODE 0x7FFFFFFF /* Invalid with all protos */ +#define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */ +#define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */ +#define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */ +#define WBCIR_MAX_IDLE_BYTES 10 + +static DEFINE_SPINLOCK(wbcir_lock); +static DEFINE_RWLOCK(keytable_lock); + +struct wbcir_key { + u32 scancode; + unsigned int keycode; +}; + +struct wbcir_keyentry { + struct wbcir_key key; + struct list_head list; +}; + +static struct wbcir_key rc6_def_keymap[] = { + { 0x800F0400, KEY_NUMERIC_0 }, + { 0x800F0401, KEY_NUMERIC_1 }, + { 0x800F0402, KEY_NUMERIC_2 }, + { 0x800F0403, KEY_NUMERIC_3 }, + { 0x800F0404, KEY_NUMERIC_4 }, + { 0x800F0405, KEY_NUMERIC_5 }, + { 0x800F0406, KEY_NUMERIC_6 }, + { 0x800F0407, KEY_NUMERIC_7 }, + { 0x800F0408, KEY_NUMERIC_8 }, + { 0x800F0409, KEY_NUMERIC_9 }, + { 0x800F041D, KEY_NUMERIC_STAR }, + { 0x800F041C, KEY_NUMERIC_POUND }, + { 0x800F0410, KEY_VOLUMEUP }, + { 0x800F0411, KEY_VOLUMEDOWN }, + { 0x800F0412, KEY_CHANNELUP }, + { 0x800F0413, KEY_CHANNELDOWN }, + { 0x800F040E, KEY_MUTE }, + { 0x800F040D, KEY_VENDOR }, /* Vista Logo Key */ + { 0x800F041E, KEY_UP }, + { 0x800F041F, KEY_DOWN }, + { 0x800F0420, KEY_LEFT }, + { 0x800F0421, KEY_RIGHT }, + { 0x800F0422, KEY_OK }, + { 0x800F0423, KEY_ESC }, + { 0x800F040F, KEY_INFO }, + { 0x800F040A, KEY_CLEAR }, + { 0x800F040B, KEY_ENTER }, + { 0x800F045B, KEY_RED }, + { 0x800F045C, KEY_GREEN }, + { 0x800F045D, KEY_YELLOW }, + { 0x800F045E, KEY_BLUE }, + { 0x800F045A, KEY_TEXT }, + { 0x800F0427, KEY_SWITCHVIDEOMODE }, + { 0x800F040C, KEY_POWER }, + { 0x800F0450, KEY_RADIO }, + { 0x800F0448, KEY_PVR }, + { 0x800F0447, KEY_AUDIO }, + { 0x800F0426, KEY_EPG }, + { 0x800F0449, KEY_CAMERA }, + { 0x800F0425, KEY_TV }, + { 0x800F044A, KEY_VIDEO }, + { 0x800F0424, KEY_DVD }, + { 0x800F0416, KEY_PLAY }, + { 0x800F0418, KEY_PAUSE }, + { 0x800F0419, KEY_STOP }, + { 0x800F0414, KEY_FASTFORWARD }, + { 0x800F041A, KEY_NEXT }, + { 0x800F041B, KEY_PREVIOUS }, + { 0x800F0415, KEY_REWIND }, + { 0x800F0417, KEY_RECORD }, +}; + +/* Registers and other state is protected by wbcir_lock */ +struct wbcir_data { + unsigned long wbase; /* Wake-Up Baseaddr */ + unsigned long ebase; /* Enhanced Func. Baseaddr */ + unsigned long sbase; /* Serial Port Baseaddr */ + unsigned int irq; /* Serial Port IRQ */ + + struct input_dev *input_dev; + struct timer_list timer_keyup; + struct led_trigger *rxtrigger; + struct led_trigger *txtrigger; + struct led_classdev led; + + u32 last_scancode; + unsigned int last_keycode; + u8 last_toggle; + u8 keypressed; + unsigned long keyup_jiffies; + unsigned int idle_count; + + /* RX irdata and parsing state */ + unsigned long irdata[30]; + unsigned int irdata_count; + unsigned int irdata_idle; + unsigned int irdata_off; + unsigned int irdata_error; + + /* Protected by keytable_lock */ + struct list_head keytable; +}; + +static enum wbcir_protocol protocol = IR_PROTOCOL_RC6; +module_param(protocol, uint, 0444); +MODULE_PARM_DESC(protocol, "IR protocol to use " + "(0 = RC5, 1 = NEC, 2 = RC6A, default)"); + +static int invert; /* default = 0 */ +module_param(invert, bool, 0444); +MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver"); + +static unsigned int wake_sc = 0x800F040C; +module_param(wake_sc, uint, 0644); +MODULE_PARM_DESC(wake_sc, "Scancode of the power-on IR command"); + +static unsigned int wake_rc6mode = 6; +module_param(wake_rc6mode, uint, 0644); +MODULE_PARM_DESC(wake_rc6mode, "RC6 mode for the power-on command " + "(0 = 0, 6 = 6A, default)"); + + + +/***************************************************************************** + * + * UTILITY FUNCTIONS + * + *****************************************************************************/ + +/* Caller needs to hold wbcir_lock */ +static void +wbcir_set_bits(unsigned long addr, u8 bits, u8 mask) +{ + u8 val; + + val = inb(addr); + val = ((val & ~mask) | (bits & mask)); + outb(val, addr); +} + +/* Selects the register bank for the serial port */ +static inline void +wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank) +{ + outb(bank, data->sbase + WBCIR_REG_SP3_BSR); +} + +static enum led_brightness +wbcir_led_brightness_get(struct led_classdev *led_cdev) +{ + struct wbcir_data *data = container_of(led_cdev, + struct wbcir_data, + led); + + if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE) + return LED_FULL; + else + return LED_OFF; +} + +static void +wbcir_led_brightness_set(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + struct wbcir_data *data = container_of(led_cdev, + struct wbcir_data, + led); + + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, + brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE, + WBCIR_LED_ENABLE); +} + +/* Manchester encodes bits to RC6 message cells (see wbcir_parse_rc6) */ +static u8 +wbcir_to_rc6cells(u8 val) +{ + u8 coded = 0x00; + int i; + + val &= 0x0F; + for (i = 0; i < 4; i++) { + if (val & 0x01) + coded |= 0x02 << (i * 2); + else + coded |= 0x01 << (i * 2); + val >>= 1; + } + + return coded; +} + + + +/***************************************************************************** + * + * INPUT FUNCTIONS + * + *****************************************************************************/ + +static unsigned int +wbcir_do_getkeycode(struct wbcir_data *data, u32 scancode) +{ + struct wbcir_keyentry *keyentry; + unsigned int keycode = KEY_RESERVED; + unsigned long flags; + + read_lock_irqsave(&keytable_lock, flags); + + list_for_each_entry(keyentry, &data->keytable, list) { + if (keyentry->key.scancode == scancode) { + keycode = keyentry->key.keycode; + break; + } + } + + read_unlock_irqrestore(&keytable_lock, flags); + return keycode; +} + +static int +wbcir_getkeycode(struct input_dev *dev, int scancode, int *keycode) +{ + struct wbcir_data *data = input_get_drvdata(dev); + + *keycode = (int)wbcir_do_getkeycode(data, (u32)scancode); + return 0; +} + +static int +wbcir_setkeycode(struct input_dev *dev, int sscancode, int keycode) +{ + struct wbcir_data *data = input_get_drvdata(dev); + struct wbcir_keyentry *keyentry; + struct wbcir_keyentry *new_keyentry; + unsigned long flags; + unsigned int old_keycode = KEY_RESERVED; + u32 scancode = (u32)sscancode; + + if (keycode < 0 || keycode > KEY_MAX) + return -EINVAL; + + new_keyentry = kmalloc(sizeof(*new_keyentry), GFP_KERNEL); + if (!new_keyentry) + return -ENOMEM; + + write_lock_irqsave(&keytable_lock, flags); + + list_for_each_entry(keyentry, &data->keytable, list) { + if (keyentry->key.scancode != scancode) + continue; + + old_keycode = keyentry->key.keycode; + keyentry->key.keycode = keycode; + + if (keyentry->key.keycode == KEY_RESERVED) { + list_del(&keyentry->list); + kfree(keyentry); + } + + break; + } + + set_bit(keycode, dev->keybit); + + if (old_keycode == KEY_RESERVED) { + new_keyentry->key.scancode = scancode; + new_keyentry->key.keycode = keycode; + list_add(&new_keyentry->list, &data->keytable); + } else { + kfree(new_keyentry); + clear_bit(old_keycode, dev->keybit); + list_for_each_entry(keyentry, &data->keytable, list) { + if (keyentry->key.keycode == old_keycode) { + set_bit(old_keycode, dev->keybit); + break; + } + } + } + + write_unlock_irqrestore(&keytable_lock, flags); + return 0; +} + +/* + * Timer function to report keyup event some time after keydown is + * reported by the ISR. + */ +static void +wbcir_keyup(unsigned long cookie) +{ + struct wbcir_data *data = (struct wbcir_data *)cookie; + unsigned long flags; + + /* + * data->keyup_jiffies is used to prevent a race condition if a + * hardware interrupt occurs at this point and the keyup timer + * event is moved further into the future as a result. + * + * The timer will then be reactivated and this function called + * again in the future. We need to exit gracefully in that case + * to allow the input subsystem to do its auto-repeat magic or + * a keyup event might follow immediately after the keydown. + */ + + spin_lock_irqsave(&wbcir_lock, flags); + + if (time_is_after_eq_jiffies(data->keyup_jiffies) && data->keypressed) { + data->keypressed = 0; + led_trigger_event(data->rxtrigger, LED_OFF); + input_report_key(data->input_dev, data->last_keycode, 0); + input_sync(data->input_dev); + } + + spin_unlock_irqrestore(&wbcir_lock, flags); +} + +static void +wbcir_keydown(struct wbcir_data *data, u32 scancode, u8 toggle) +{ + unsigned int keycode; + + /* Repeat? */ + if (data->last_scancode == scancode && + data->last_toggle == toggle && + data->keypressed) + goto set_timer; + data->last_scancode = scancode; + + /* Do we need to release an old keypress? */ + if (data->keypressed) { + input_report_key(data->input_dev, data->last_keycode, 0); + input_sync(data->input_dev); + data->keypressed = 0; + } + + /* Report scancode */ + input_event(data->input_dev, EV_MSC, MSC_SCAN, (int)scancode); + + /* Do we know this scancode? */ + keycode = wbcir_do_getkeycode(data, scancode); + if (keycode == KEY_RESERVED) + goto set_timer; + + /* Register a keypress */ + input_report_key(data->input_dev, keycode, 1); + data->keypressed = 1; + data->last_keycode = keycode; + data->last_toggle = toggle; + +set_timer: + input_sync(data->input_dev); + led_trigger_event(data->rxtrigger, + data->keypressed ? LED_FULL : LED_OFF); + data->keyup_jiffies = jiffies + msecs_to_jiffies(IR_KEYPRESS_TIMEOUT); + mod_timer(&data->timer_keyup, data->keyup_jiffies); +} + + + +/***************************************************************************** + * + * IR PARSING FUNCTIONS + * + *****************************************************************************/ + +/* Resets all irdata */ +static void +wbcir_reset_irdata(struct wbcir_data *data) +{ + memset(data->irdata, 0, sizeof(data->irdata)); + data->irdata_count = 0; + data->irdata_off = 0; + data->irdata_error = 0; +} + +/* Adds one bit of irdata */ +static void +add_irdata_bit(struct wbcir_data *data, int set) +{ + if (data->irdata_count >= sizeof(data->irdata) * 8) { + data->irdata_error = 1; + return; + } + + if (set) + __set_bit(data->irdata_count, data->irdata); + data->irdata_count++; +} + +/* Gets count bits of irdata */ +static u16 +get_bits(struct wbcir_data *data, int count) +{ + u16 val = 0x0; + + if (data->irdata_count - data->irdata_off < count) { + data->irdata_error = 1; + return 0x0; + } + + while (count > 0) { + val <<= 1; + if (test_bit(data->irdata_off, data->irdata)) + val |= 0x1; + count--; + data->irdata_off++; + } + + return val; +} + +/* Reads 16 cells and converts them to a byte */ +static u8 +wbcir_rc6cells_to_byte(struct wbcir_data *data) +{ + u16 raw = get_bits(data, 16); + u8 val = 0x00; + int bit; + + for (bit = 0; bit < 8; bit++) { + switch (raw & 0x03) { + case 0x01: + break; + case 0x02: + val |= (0x01 << bit); + break; + default: + data->irdata_error = 1; + break; + } + raw >>= 2; + } + + return val; +} + +/* Decodes a number of bits from raw RC5 data */ +static u8 +wbcir_get_rc5bits(struct wbcir_data *data, unsigned int count) +{ + u16 raw = get_bits(data, count * 2); + u8 val = 0x00; + int bit; + + for (bit = 0; bit < count; bit++) { + switch (raw & 0x03) { + case 0x01: + val |= (0x01 << bit); + break; + case 0x02: + break; + default: + data->irdata_error = 1; + break; + } + raw >>= 2; + } + + return val; +} + +static void +wbcir_parse_rc6(struct device *dev, struct wbcir_data *data) +{ + /* + * Normal bits are manchester coded as follows: + * cell0 + cell1 = logic "0" + * cell1 + cell0 = logic "1" + * + * The IR pulse has the following components: + * + * Leader - 6 * cell1 - discarded + * Gap - 2 * cell0 - discarded + * Start bit - Normal Coding - always "1" + * Mode Bit 2 - 0 - Normal Coding + * Toggle bit - Normal Coding with double bit time, + * e.g. cell0 + cell0 + cell1 + cell1 + * means logic "0". + * + * The rest depends on the mode, the following modes are known: + * + * MODE 0: + * Address Bit 7 - 0 - Normal Coding + * Command Bit 7 - 0 - Normal Coding + * + * MODE 6: + * The above Toggle Bit is used as a submode bit, 0 = A, 1 = B. + * Submode B is for pointing devices, only remotes using submode A + * are supported. + * + * Customer range bit - 0 => Customer = 7 bits, 0...127 + * 1 => Customer = 15 bits, 32768...65535 + * Customer Bits - Normal Coding + * + * Customer codes are allocated by Philips. The rest of the bits + * are customer dependent. The following is commonly used (and the + * only supported config): + * + * Toggle Bit - Normal Coding + * Address Bit 6 - 0 - Normal Coding + * Command Bit 7 - 0 - Normal Coding + * + * All modes are followed by at least 6 * cell0. + * + * MODE 0 msglen: + * 1 * 2 (start bit) + 3 * 2 (mode) + 2 * 2 (toggle) + + * 8 * 2 (address) + 8 * 2 (command) = + * 44 cells + * + * MODE 6A msglen: + * 1 * 2 (start bit) + 3 * 2 (mode) + 2 * 2 (submode) + + * 1 * 2 (customer range bit) + 7/15 * 2 (customer bits) + + * 1 * 2 (toggle bit) + 7 * 2 (address) + 8 * 2 (command) = + * 60 - 76 cells + */ + u8 mode; + u8 toggle; + u16 customer = 0x0; + u8 address; + u8 command; + u32 scancode; + + /* Leader mark */ + while (get_bits(data, 1) && !data->irdata_error) + /* Do nothing */; + + /* Leader space */ + if (get_bits(data, 1)) { + dev_dbg(dev, "RC6 - Invalid leader space\n"); + return; + } + + /* Start bit */ + if (get_bits(data, 2) != 0x02) { + dev_dbg(dev, "RC6 - Invalid start bit\n"); + return; + } + + /* Mode */ + mode = get_bits(data, 6); + switch (mode) { + case 0x15: /* 010101 = b000 */ + mode = 0; + break; + case 0x29: /* 101001 = b110 */ + mode = 6; + break; + default: + dev_dbg(dev, "RC6 - Invalid mode\n"); + return; + } + + /* Toggle bit / Submode bit */ + toggle = get_bits(data, 4); + switch (toggle) { + case 0x03: + toggle = 0; + break; + case 0x0C: + toggle = 1; + break; + default: + dev_dbg(dev, "RC6 - Toggle bit error\n"); + break; + } + + /* Customer */ + if (mode == 6) { + if (toggle != 0) { + dev_dbg(dev, "RC6B - Not Supported\n"); + return; + } + + customer = wbcir_rc6cells_to_byte(data); + + if (customer & 0x80) { + /* 15 bit customer value */ + customer <<= 8; + customer |= wbcir_rc6cells_to_byte(data); + } + } + + /* Address */ + address = wbcir_rc6cells_to_byte(data); + if (mode == 6) { + toggle = address >> 7; + address &= 0x7F; + } + + /* Command */ + command = wbcir_rc6cells_to_byte(data); + + /* Create scancode */ + scancode = command; + scancode |= address << 8; + scancode |= customer << 16; + + /* Last sanity check */ + if (data->irdata_error) { + dev_dbg(dev, "RC6 - Cell error(s)\n"); + return; + } + + dev_info(dev, "IR-RC6 ad 0x%02X cm 0x%02X cu 0x%04X " + "toggle %u mode %u scan 0x%08X\n", + address, + command, + customer, + (unsigned int)toggle, + (unsigned int)mode, + scancode); + + wbcir_keydown(data, scancode, toggle); +} + +static void +wbcir_parse_rc5(struct device *dev, struct wbcir_data *data) +{ + /* + * Bits are manchester coded as follows: + * cell1 + cell0 = logic "0" + * cell0 + cell1 = logic "1" + * (i.e. the reverse of RC6) + * + * Start bit 1 - "1" - discarded + * Start bit 2 - Must be inverted to get command bit 6 + * Toggle bit + * Address Bit 4 - 0 + * Command Bit 5 - 0 + */ + u8 toggle; + u8 address; + u8 command; + u32 scancode; + + /* Start bit 1 */ + if (!get_bits(data, 1)) { + dev_dbg(dev, "RC5 - Invalid start bit\n"); + return; + } + + /* Start bit 2 */ + if (!wbcir_get_rc5bits(data, 1)) + command = 0x40; + else + command = 0x00; + + toggle = wbcir_get_rc5bits(data, 1); + address = wbcir_get_rc5bits(data, 5); + command |= wbcir_get_rc5bits(data, 6); + scancode = address << 7 | command; + + /* Last sanity check */ + if (data->irdata_error) { + dev_dbg(dev, "RC5 - Invalid message\n"); + return; + } + + dev_dbg(dev, "IR-RC5 ad %u cm %u t %u s %u\n", + (unsigned int)address, + (unsigned int)command, + (unsigned int)toggle, + (unsigned int)scancode); + + wbcir_keydown(data, scancode, toggle); +} + +static void +wbcir_parse_nec(struct device *dev, struct wbcir_data *data) +{ + /* + * Each bit represents 560 us. + * + * Leader - 9 ms burst + * Gap - 4.5 ms silence + * Address1 bit 0 - 7 - Address 1 + * Address2 bit 0 - 7 - Address 2 + * Command1 bit 0 - 7 - Command 1 + * Command2 bit 0 - 7 - Command 2 + * + * Note the bit order! + * + * With the old NEC protocol, Address2 was the inverse of Address1 + * and Command2 was the inverse of Command1 and were used as + * an error check. + * + * With NEC extended, Address1 is the LSB of the Address and + * Address2 is the MSB, Command parsing remains unchanged. + * + * A repeat message is coded as: + * Leader - 9 ms burst + * Gap - 2.25 ms silence + * Repeat - 560 us active + */ + u8 address1; + u8 address2; + u8 command1; + u8 command2; + u16 address; + u32 scancode; + + /* Leader mark */ + while (get_bits(data, 1) && !data->irdata_error) + /* Do nothing */; + + /* Leader space */ + if (get_bits(data, 4)) { + dev_dbg(dev, "NEC - Invalid leader space\n"); + return; + } + + /* Repeat? */ + if (get_bits(data, 1)) { + if (!data->keypressed) { + dev_dbg(dev, "NEC - Stray repeat message\n"); + return; + } + + dev_dbg(dev, "IR-NEC repeat s %u\n", + (unsigned int)data->last_scancode); + + wbcir_keydown(data, data->last_scancode, data->last_toggle); + return; + } + + /* Remaining leader space */ + if (get_bits(data, 3)) { + dev_dbg(dev, "NEC - Invalid leader space\n"); + return; + } + + address1 = bitrev8(get_bits(data, 8)); + address2 = bitrev8(get_bits(data, 8)); + command1 = bitrev8(get_bits(data, 8)); + command2 = bitrev8(get_bits(data, 8)); + + /* Sanity check */ + if (data->irdata_error) { + dev_dbg(dev, "NEC - Invalid message\n"); + return; + } + + /* Check command validity */ + if (command1 != ~command2) { + dev_dbg(dev, "NEC - Command bytes mismatch\n"); + return; + } + + /* Check for extended NEC protocol */ + address = address1; + if (address1 != ~address2) + address |= address2 << 8; + + scancode = address << 8 | command1; + + dev_dbg(dev, "IR-NEC ad %u cm %u s %u\n", + (unsigned int)address, + (unsigned int)command1, + (unsigned int)scancode); + + wbcir_keydown(data, scancode, !data->last_toggle); +} + + + +/***************************************************************************** + * + * INTERRUPT FUNCTIONS + * + *****************************************************************************/ + +static irqreturn_t +wbcir_irq_handler(int irqno, void *cookie) +{ + struct pnp_dev *device = cookie; + struct wbcir_data *data = pnp_get_drvdata(device); + struct device *dev = &device->dev; + u8 status; + unsigned long flags; + u8 irdata[8]; + int i; + unsigned int hw; + + spin_lock_irqsave(&wbcir_lock, flags); + + wbcir_select_bank(data, WBCIR_BANK_0); + + status = inb(data->sbase + WBCIR_REG_SP3_EIR); + + if (!(status & (WBCIR_IRQ_RX | WBCIR_IRQ_ERR))) { + spin_unlock_irqrestore(&wbcir_lock, flags); + return IRQ_NONE; + } + + if (status & WBCIR_IRQ_ERR) + data->irdata_error = 1; + + if (!(status & WBCIR_IRQ_RX)) + goto out; + + /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */ + insb(data->sbase + WBCIR_REG_SP3_RXDATA, &irdata[0], 8); + + for (i = 0; i < sizeof(irdata); i++) { + hw = hweight8(irdata[i]); + if (hw > 4) + add_irdata_bit(data, 0); + else + add_irdata_bit(data, 1); + + if (hw == 8) + data->idle_count++; + else + data->idle_count = 0; + } + + if (data->idle_count > WBCIR_MAX_IDLE_BYTES) { + /* Set RXINACTIVE... */ + outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR); + + /* ...and drain the FIFO */ + while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) + inb(data->sbase + WBCIR_REG_SP3_RXDATA); + + dev_dbg(dev, "IRDATA:\n"); + for (i = 0; i < data->irdata_count; i += BITS_PER_LONG) + dev_dbg(dev, "0x%08lX\n", data->irdata[i/BITS_PER_LONG]); + + switch (protocol) { + case IR_PROTOCOL_RC5: + wbcir_parse_rc5(dev, data); + break; + case IR_PROTOCOL_RC6: + wbcir_parse_rc6(dev, data); + break; + case IR_PROTOCOL_NEC: + wbcir_parse_nec(dev, data); + break; + } + + wbcir_reset_irdata(data); + data->idle_count = 0; + } + +out: + spin_unlock_irqrestore(&wbcir_lock, flags); + return IRQ_HANDLED; +} + + + +/***************************************************************************** + * + * SUSPEND/RESUME FUNCTIONS + * + *****************************************************************************/ + +static void +wbcir_shutdown(struct pnp_dev *device) +{ + struct device *dev = &device->dev; + struct wbcir_data *data = pnp_get_drvdata(device); + int do_wake = 1; + u8 match[11]; + u8 mask[11]; + u8 rc6_csl = 0; + int i; + + memset(match, 0, sizeof(match)); + memset(mask, 0, sizeof(mask)); + + if (wake_sc == INVALID_SCANCODE || !device_may_wakeup(dev)) { + do_wake = 0; + goto finish; + } + + switch (protocol) { + case IR_PROTOCOL_RC5: + if (wake_sc > 0xFFF) { + do_wake = 0; + dev_err(dev, "RC5 - Invalid wake scancode\n"); + break; + } + + /* Mask = 13 bits, ex toggle */ + mask[0] = 0xFF; + mask[1] = 0x17; + + match[0] = (wake_sc & 0x003F); /* 6 command bits */ + match[0] |= (wake_sc & 0x0180) >> 1; /* 2 address bits */ + match[1] = (wake_sc & 0x0E00) >> 9; /* 3 address bits */ + if (!(wake_sc & 0x0040)) /* 2nd start bit */ + match[1] |= 0x10; + + break; + + case IR_PROTOCOL_NEC: + if (wake_sc > 0xFFFFFF) { + do_wake = 0; + dev_err(dev, "NEC - Invalid wake scancode\n"); + break; + } + + mask[0] = mask[1] = mask[2] = mask[3] = 0xFF; + + match[1] = bitrev8((wake_sc & 0xFF)); + match[0] = ~match[1]; + + match[3] = bitrev8((wake_sc & 0xFF00) >> 8); + if (wake_sc > 0xFFFF) + match[2] = bitrev8((wake_sc & 0xFF0000) >> 16); + else + match[2] = ~match[3]; + + break; + + case IR_PROTOCOL_RC6: + + if (wake_rc6mode == 0) { + if (wake_sc > 0xFFFF) { + do_wake = 0; + dev_err(dev, "RC6 - Invalid wake scancode\n"); + break; + } + + /* Command */ + match[0] = wbcir_to_rc6cells(wake_sc >> 0); + mask[0] = 0xFF; + match[1] = wbcir_to_rc6cells(wake_sc >> 4); + mask[1] = 0xFF; + + /* Address */ + match[2] = wbcir_to_rc6cells(wake_sc >> 8); + mask[2] = 0xFF; + match[3] = wbcir_to_rc6cells(wake_sc >> 12); + mask[3] = 0xFF; + + /* Header */ + match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */ + mask[4] = 0xF0; + match[5] = 0x09; /* start bit = 1, mode2 = 0 */ + mask[5] = 0x0F; + + rc6_csl = 44; + + } else if (wake_rc6mode == 6) { + i = 0; + + /* Command */ + match[i] = wbcir_to_rc6cells(wake_sc >> 0); + mask[i++] = 0xFF; + match[i] = wbcir_to_rc6cells(wake_sc >> 4); + mask[i++] = 0xFF; + + /* Address + Toggle */ + match[i] = wbcir_to_rc6cells(wake_sc >> 8); + mask[i++] = 0xFF; + match[i] = wbcir_to_rc6cells(wake_sc >> 12); + mask[i++] = 0x3F; + + /* Customer bits 7 - 0 */ + match[i] = wbcir_to_rc6cells(wake_sc >> 16); + mask[i++] = 0xFF; + match[i] = wbcir_to_rc6cells(wake_sc >> 20); + mask[i++] = 0xFF; + + if (wake_sc & 0x80000000) { + /* Customer range bit and bits 15 - 8 */ + match[i] = wbcir_to_rc6cells(wake_sc >> 24); + mask[i++] = 0xFF; + match[i] = wbcir_to_rc6cells(wake_sc >> 28); + mask[i++] = 0xFF; + rc6_csl = 76; + } else if (wake_sc <= 0x007FFFFF) { + rc6_csl = 60; + } else { + do_wake = 0; + dev_err(dev, "RC6 - Invalid wake scancode\n"); + break; + } + + /* Header */ + match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */ + mask[i++] = 0xFF; + match[i] = 0x0A; /* start bit = 1, mode2 = 1 */ + mask[i++] = 0x0F; + + } else { + do_wake = 0; + dev_err(dev, "RC6 - Invalid wake mode\n"); + } + + break; + + default: + do_wake = 0; + break; + } + +finish: + if (do_wake) { + /* Set compare and compare mask */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, + WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0, + 0x3F); + outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11); + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, + WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0, + 0x3F); + outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11); + + /* RC6 Compare String Len */ + outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07); + + /* Set CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x01, 0x01); + + } else { + /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* Clear CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); + } + + /* Disable interrupts */ + outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); +} + +static int +wbcir_suspend(struct pnp_dev *device, pm_message_t state) +{ + wbcir_shutdown(device); + return 0; +} + +static int +wbcir_resume(struct pnp_dev *device) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + + /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* Clear CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); + + /* Enable interrupts */ + wbcir_reset_irdata(data); + outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); + + return 0; +} + + + +/***************************************************************************** + * + * SETUP/INIT FUNCTIONS + * + *****************************************************************************/ + +static void +wbcir_cfg_ceir(struct wbcir_data *data) +{ + u8 tmp; + + /* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */ + tmp = protocol << 4; + if (invert) + tmp |= 0x08; + outb(tmp, data->wbase + WBCIR_REG_WCEIR_CTL); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* Set RC5 cell time to correspond to 36 kHz */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F); + + /* Set IRTX_INV */ + if (invert) + outb(0x04, data->ebase + WBCIR_REG_ECEIR_CCTL); + else + outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL); + + /* + * Clear IR LED, set SP3 clock to 24Mhz + * set SP3_IRRX_SW to binary 01, helpfully not documented + */ + outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS); +} + +static int __devinit +wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id) +{ + struct device *dev = &device->dev; + struct wbcir_data *data; + int err; + + if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN && + pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN && + pnp_port_len(device, 2) == SP_IOMEM_LEN)) { + dev_err(dev, "Invalid resources\n"); + return -ENODEV; + } + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + pnp_set_drvdata(device, data); + + data->ebase = pnp_port_start(device, 0); + data->wbase = pnp_port_start(device, 1); + data->sbase = pnp_port_start(device, 2); + data->irq = pnp_irq(device, 0); + + if (data->wbase == 0 || data->ebase == 0 || + data->sbase == 0 || data->irq == 0) { + err = -ENODEV; + dev_err(dev, "Invalid resources\n"); + goto exit_free_data; + } + + dev_dbg(&device->dev, "Found device " + "(w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n", + data->wbase, data->ebase, data->sbase, data->irq); + + if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_free_data; + } + + if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_release_wbase; + } + + if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->sbase, data->sbase + SP_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_release_ebase; + } + + err = request_irq(data->irq, wbcir_irq_handler, + IRQF_DISABLED, DRVNAME, device); + if (err) { + dev_err(dev, "Failed to claim IRQ %u\n", data->irq); + err = -EBUSY; + goto exit_release_sbase; + } + + led_trigger_register_simple("cir-tx", &data->txtrigger); + if (!data->txtrigger) { + err = -ENOMEM; + goto exit_free_irq; + } + + led_trigger_register_simple("cir-rx", &data->rxtrigger); + if (!data->rxtrigger) { + err = -ENOMEM; + goto exit_unregister_txtrigger; + } + + data->led.name = "cir::activity"; + data->led.default_trigger = "cir-rx"; + data->led.brightness_set = wbcir_led_brightness_set; + data->led.brightness_get = wbcir_led_brightness_get; + err = led_classdev_register(&device->dev, &data->led); + if (err) + goto exit_unregister_rxtrigger; + + data->input_dev = input_allocate_device(); + if (!data->input_dev) { + err = -ENOMEM; + goto exit_unregister_led; + } + + data->input_dev->evbit[0] = BIT(EV_KEY); + data->input_dev->name = WBCIR_NAME; + data->input_dev->phys = "wbcir/cir0"; + data->input_dev->id.bustype = BUS_HOST; + data->input_dev->id.vendor = PCI_VENDOR_ID_WINBOND; + data->input_dev->id.product = WBCIR_ID_FAMILY; + data->input_dev->id.version = WBCIR_ID_CHIP; + data->input_dev->getkeycode = wbcir_getkeycode; + data->input_dev->setkeycode = wbcir_setkeycode; + input_set_capability(data->input_dev, EV_MSC, MSC_SCAN); + input_set_drvdata(data->input_dev, data); + + err = input_register_device(data->input_dev); + if (err) + goto exit_free_input; + + data->last_scancode = INVALID_SCANCODE; + INIT_LIST_HEAD(&data->keytable); + setup_timer(&data->timer_keyup, wbcir_keyup, (unsigned long)data); + + /* Load default keymaps */ + if (protocol == IR_PROTOCOL_RC6) { + int i; + for (i = 0; i < ARRAY_SIZE(rc6_def_keymap); i++) { + err = wbcir_setkeycode(data->input_dev, + (int)rc6_def_keymap[i].scancode, + (int)rc6_def_keymap[i].keycode); + if (err) + goto exit_unregister_keys; + } + } + + device_init_wakeup(&device->dev, 1); + + wbcir_cfg_ceir(data); + + /* Disable interrupts */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); + + /* Enable extended mode */ + wbcir_select_bank(data, WBCIR_BANK_2); + outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); + + /* + * Configure baud generator, IR data will be sampled at + * a bitrate of: (24Mhz * prescaler) / (divisor * 16). + * + * The ECIR registers include a flag to change the + * 24Mhz clock freq to 48Mhz. + * + * It's not documented in the specs, but fifo levels + * other than 16 seems to be unsupported. + */ + + /* prescaler 1.0, tx/rx fifo lvl 16 */ + outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); + + /* Set baud divisor to generate one byte per bit/cell */ + switch (protocol) { + case IR_PROTOCOL_RC5: + outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL); + break; + case IR_PROTOCOL_RC6: + outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL); + break; + case IR_PROTOCOL_NEC: + outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL); + break; + } + outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); + + /* Set CEIR mode */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); + inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ + inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ + + /* Disable RX demod, run-length encoding/decoding, set freq span */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG); + + /* Disable timer */ + wbcir_select_bank(data, WBCIR_BANK_4); + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); + + /* Enable MSR interrupt, Clear AUX_IRX */ + wbcir_select_bank(data, WBCIR_BANK_5); + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2); + + /* Disable CRC */ + wbcir_select_bank(data, WBCIR_BANK_6); + outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); + + /* Set RX/TX (de)modulation freq, not really used */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); + outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); + + /* Set invert and pin direction */ + if (invert) + outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); + else + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); + + /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); + + /* Clear AUX status bits */ + outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); + + /* Enable interrupts */ + outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); + + return 0; + +exit_unregister_keys: + if (!list_empty(&data->keytable)) { + struct wbcir_keyentry *key; + struct wbcir_keyentry *keytmp; + + list_for_each_entry_safe(key, keytmp, &data->keytable, list) { + list_del(&key->list); + kfree(key); + } + } + input_unregister_device(data->input_dev); + /* Can't call input_free_device on an unregistered device */ + data->input_dev = NULL; +exit_free_input: + input_free_device(data->input_dev); +exit_unregister_led: + led_classdev_unregister(&data->led); +exit_unregister_rxtrigger: + led_trigger_unregister_simple(data->rxtrigger); +exit_unregister_txtrigger: + led_trigger_unregister_simple(data->txtrigger); +exit_free_irq: + free_irq(data->irq, device); +exit_release_sbase: + release_region(data->sbase, SP_IOMEM_LEN); +exit_release_ebase: + release_region(data->ebase, EHFUNC_IOMEM_LEN); +exit_release_wbase: + release_region(data->wbase, WAKEUP_IOMEM_LEN); +exit_free_data: + kfree(data); + pnp_set_drvdata(device, NULL); +exit: + return err; +} + +static void __devexit +wbcir_remove(struct pnp_dev *device) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + struct wbcir_keyentry *key; + struct wbcir_keyentry *keytmp; + + /* Disable interrupts */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); + + del_timer_sync(&data->timer_keyup); + + free_irq(data->irq, device); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); + + /* Clear BUFF_EN, END_EN, MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* This will generate a keyup event if necessary */ + input_unregister_device(data->input_dev); + + led_trigger_unregister_simple(data->rxtrigger); + led_trigger_unregister_simple(data->txtrigger); + led_classdev_unregister(&data->led); + + /* This is ok since &data->led isn't actually used */ + wbcir_led_brightness_set(&data->led, LED_OFF); + + release_region(data->wbase, WAKEUP_IOMEM_LEN); + release_region(data->ebase, EHFUNC_IOMEM_LEN); + release_region(data->sbase, SP_IOMEM_LEN); + + list_for_each_entry_safe(key, keytmp, &data->keytable, list) { + list_del(&key->list); + kfree(key); + } + + kfree(data); + + pnp_set_drvdata(device, NULL); +} + +static const struct pnp_device_id wbcir_ids[] = { + { "WEC1022", 0 }, + { "", 0 } +}; +MODULE_DEVICE_TABLE(pnp, wbcir_ids); + +static struct pnp_driver wbcir_driver = { + .name = WBCIR_NAME, + .id_table = wbcir_ids, + .probe = wbcir_probe, + .remove = __devexit_p(wbcir_remove), + .suspend = wbcir_suspend, + .resume = wbcir_resume, + .shutdown = wbcir_shutdown +}; + +static int __init +wbcir_init(void) +{ + int ret; + + switch (protocol) { + case IR_PROTOCOL_RC5: + case IR_PROTOCOL_NEC: + case IR_PROTOCOL_RC6: + break; + default: + printk(KERN_ERR DRVNAME ": Invalid protocol argument\n"); + return -EINVAL; + } + + ret = pnp_register_driver(&wbcir_driver); + if (ret) + printk(KERN_ERR DRVNAME ": Unable to register driver\n"); + + return ret; +} + +static void __exit +wbcir_exit(void) +{ + pnp_unregister_driver(&wbcir_driver); +} + +MODULE_AUTHOR("David Härdeman "); +MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver"); +MODULE_LICENSE("GPL"); + +module_init(wbcir_init); +module_exit(wbcir_exit); + + -- David Härdeman -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/