| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20090817172612.1dfa74a5.pablo.bitton@gmail.com>
Date: Mon, 17 Aug 2009 17:26:12 +0300
From: Pablo Bitton <pablo.bitton@...il.com>
To: davinci-linux-open-source@...ux.davincidsp.com,
linux-kernel@...r.kernel.org, s-paulraj@...com
Subject: [PATCH v2] SPI: DaVinci: Adding SPI driver for DaVinci
This patch adds support for SPI in DaVinci DM6446
(and tries to keep support for DM355/DM365/DM6467 and DA8xx).
Mostly the same as the patch by Sandeep Paulraj.
This has been tested on the DM6446 by defining a spidev device and using a
scope (to check correctness) and a hardware loopback.
This was NOT tested on DM355, DM365 and DM6467 - in fact, it will probably
not work "as is" because its default mode is CS low-inactive (default mode
of SPI in kernel) - need to set CS_HIGH mode to work as in the previous patch.
Changes from the patch by Sandeep Paulraj:
Bug fixes:
* Additional word written with chip select up after each transfer.
Particulary problematic with NO_CS mode where this word can't be
distiguished from correct words. Problem was in davinci_chip_select.
* setup() for one chip select may interfere with transfer for another
* Small nitpicks (bits that can be changed only on VERSION_2)
Features added:
* Support DM6446
* Support CS_HIGH mode (using SPIDEF register). Note that CS low is default.
Other:
* Less accesses to registers used.
* Once-per-device configuration is done only in probe(), not each transfer.
Uglyness still there:
* VERSION_X definitions for different SPI controllers - added VERSION_3
for the dm6446, which is ugly.
NOTE:
This patch is based on following patches:
SPI: DaVinci: Adding SPI driver for DM3xx/DM6467/DA8xx
The patch adds support for SPI in DaVinci
DM355/DM365/DM6467 and DA8xx.
This has been tested on the DM355, DM365 and DM6467 EVMs using
the EEPROM connected to SPI0
Signed-off-by: Sandeep Paulraj <s-paulraj@...com>
DaVinci: DM646x: Adding Support for SPI
The patch does the following
1) Adds a clock for SPI
2) Defines resources specific to DM646x SOC
Signed-off-by: Sandeep Paulraj <s-paulraj@...com>
Signed-off-by: Pablo Bitton <pablo.bitton@...il.com>
---
arch/arm/mach-davinci/dm644x.c | 50 ++-
arch/arm/mach-davinci/dm646x.c | 53 ++
arch/arm/mach-davinci/include/mach/dm644x.h | 3 +
arch/arm/mach-davinci/include/mach/dm646x.h | 2 +
arch/arm/mach-davinci/include/mach/spi.h | 46 ++
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/davinci_spi.c | 771 +++++++++++++++++++++++++++
drivers/spi/davinci_spi.h | 178 ++++++
12 files changed, 1149 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-davinci/include/mach/spi.h
create mode 100644 drivers/spi/davinci_spi.c
create mode 100644 drivers/spi/davinci_spi.h
diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c
index 55317b1..d395354 100644
--- a/arch/arm/mach-davinci/dm644x.c
+++ b/arch/arm/mach-davinci/dm644x.c
@@ -14,6 +14,7 @@
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/spi/spi.h>
#include <asm/mach/map.h>
@@ -28,6 +29,7 @@
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/spi.h>
#include "clock.h"
#include "mux.h"
@@ -306,7 +308,7 @@ struct davinci_clk dm644x_clks[] = {
CLK("palm_bk3710", NULL, &ide_clk),
CLK("davinci-asp", NULL, &asp_clk),
CLK("davinci_mmc.0", NULL, &mmcsd_clk),
- CLK(NULL, "spi", &spi_clk),
+ CLK("spi_davinci.0", NULL, &spi_clk),
CLK(NULL, "gpio", &gpio_clk),
CLK(NULL, "usb", &usb_clk),
CLK(NULL, "vlynq", &vlynq_clk),
@@ -320,6 +322,52 @@ struct davinci_clk dm644x_clks[] = {
CLK(NULL, NULL, NULL),
};
+
+static u64 dm644x_spi_dma_mask = DMA_BIT_MASK(32);
+
+static struct davinci_spi_platform_data dm644x_spi_pdata = {
+ .version = SPI_VERSION_3,
+ .num_chipselect = 2,
+ .clk_internal = 1,
+ .cs_hold = 0,
+ .intr_level = 0,
+ .poll_mode = 1,
+ .c2tdelay = 8,
+ .t2cdelay = 8,
+};
+
+static struct resource dm644x_spi_resources[] = {
+ {
+ .start = 0x01c66800,
+ .end = 0x01c66fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_SPINT0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device dm644x_spi_device = {
+ .name = "spi_davinci",
+ .id = 0,
+ .dev = {
+ .dma_mask = &dm644x_spi_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &dm644x_spi_pdata,
+ },
+ .num_resources = ARRAY_SIZE(dm644x_spi_resources),
+ .resource = dm644x_spi_resources,
+};
+
+void __init dm644x_init_spi(struct spi_board_info *info, unsigned len)
+{
+ spi_register_board_info(info, len);
+
+ platform_device_register(&dm644x_spi_device);
+}
+
+
static struct emac_platform_data dm644x_emac_pdata = {
.ctrl_reg_offset = DM644X_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM644X_EMAC_CNTRL_MOD_OFFSET,
diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
index 50f01e0..66857ef 100644
--- a/arch/arm/mach-davinci/dm646x.c
+++ b/arch/arm/mach-davinci/dm646x.c
@@ -14,6 +14,7 @@
#include <linux/serial_8250.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
+#include <linux/spi/spi.h>
#include <asm/mach/map.h>
@@ -28,6 +29,7 @@
#include <mach/serial.h>
#include <mach/common.h>
#include <mach/asp.h>
+#include <mach/spi.h>
#include "clock.h"
#include "mux.h"
@@ -253,6 +255,12 @@ static struct clk emac_clk = {
.lpsc = DM646X_LPSC_EMAC,
};
+static struct clk spi0_clk = {
+ .name = "spi0",
+ .parent = &pll1_sysclk3,
+ .lpsc = DM646X_LPSC_SPI,
+};
+
static struct clk pwm0_clk = {
.name = "pwm0",
.parent = &pll1_sysclk3,
@@ -338,6 +346,7 @@ struct davinci_clk dm646x_clks[] = {
CLK("davinci-mcasp.1", NULL, &mcasp1_clk),
CLK(NULL, "aemif", &aemif_clk),
CLK("davinci_emac.1", NULL, &emac_clk),
+ CLK("spi_davinci.0", NULL, &spi0_clk),
CLK(NULL, "pwm0", &pwm0_clk),
CLK(NULL, "pwm1", &pwm1_clk),
CLK(NULL, "timer0", &timer0_clk),
@@ -349,6 +358,50 @@ struct davinci_clk dm646x_clks[] = {
CLK(NULL, NULL, NULL),
};
+static u64 dm646x_spi0_dma_mask = DMA_BIT_MASK(32);
+
+static struct davinci_spi_platform_data dm646x_spi0_pdata = {
+ .version = SPI_VERSION_1,
+ .num_chipselect = 2,
+ .clk_internal = 1,
+ .cs_hold = 1,
+ .intr_level = 0,
+ .poll_mode = 1,
+ .c2tdelay = 8,
+ .t2cdelay = 8,
+};
+
+static struct resource dm646x_spi0_resources[] = {
+ {
+ .start = 0x01c66800,
+ .end = 0x01c66fff,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_DM646X_SPINT0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device dm646x_spi0_device = {
+ .name = "spi_davinci",
+ .id = 0,
+ .dev = {
+ .dma_mask = &dm646x_spi0_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ .platform_data = &dm646x_spi0_pdata,
+ },
+ .num_resources = ARRAY_SIZE(dm646x_spi0_resources),
+ .resource = dm646x_spi0_resources,
+};
+
+void __init dm646x_init_spi0(struct spi_board_info *info, unsigned len)
+{
+ spi_register_board_info(info, len);
+
+ platform_device_register(&dm646x_spi0_device);
+}
+
static struct emac_platform_data dm646x_emac_pdata = {
.ctrl_reg_offset = DM646X_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM646X_EMAC_CNTRL_MOD_OFFSET,
diff --git a/arch/arm/mach-davinci/include/mach/dm644x.h b/arch/arm/mach-davinci/include/mach/dm644x.h
index 8b157ce..0710596 100644
--- a/arch/arm/mach-davinci/include/mach/dm644x.h
+++ b/arch/arm/mach-davinci/include/mach/dm644x.h
@@ -36,5 +36,8 @@
void __init dm644x_init(void);
void __init dm644x_init_asp(struct snd_platform_data *pdata);
+struct spi_board_info;
+void __init dm644x_init_spi(struct spi_board_info *info, unsigned len);
+
#endif /* __ASM_ARCH_DM644X_H */
diff --git a/arch/arm/mach-davinci/include/mach/dm646x.h b/arch/arm/mach-davinci/include/mach/dm646x.h
index 0585484..498163f 100644
--- a/arch/arm/mach-davinci/include/mach/dm646x.h
+++ b/arch/arm/mach-davinci/include/mach/dm646x.h
@@ -25,5 +25,7 @@
void __init dm646x_init_ide(void);
void __init dm646x_init_mcasp0(struct snd_platform_data *pdata);
void __init dm646x_init_mcasp1(struct snd_platform_data *pdata);
+struct spi_board_info;
+void dm646x_init_spi0(struct spi_board_info *info, unsigned len);
void dm646x_video_init(void);
diff --git a/arch/arm/mach-davinci/include/mach/spi.h b/arch/arm/mach-davinci/include/mach/spi.h
new file mode 100644
index 0000000..93b4b4d
--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/spi.h
@@ -0,0 +1,46 @@
+/*
+ * Copyright 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_DAVINCI_SPI_H
+#define __ARCH_ARM_DAVINCI_SPI_H
+
+#define SPI_INTERN_CS 0xFF
+
+enum {
+ SPI_VERSION_1 = 0, /* For DM355/DM365/DM6467*/
+ SPI_VERSION_2, /* For DA8xx */
+ SPI_VERSION_3, /* For DM6446 */
+};
+
+struct davinci_spi_platform_data {
+ u8 version;
+ u16 num_chipselect;
+ u32 wdelay;
+ u32 odd_parity;
+ u32 parity_enable;
+ u32 wait_enable;
+ u32 timer_disable;
+ u32 clk_internal;
+ u32 cs_hold;
+ u32 intr_level;
+ u32 poll_mode;
+ u8 c2tdelay;
+ u8 t2cdelay;
+};
+
+#endif /* __ARCH_ARM_DAVINCI_SPI_H */
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 2c733c2..7fe9211 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -77,6 +77,13 @@ config SPI_AU1550
This driver can also be built as a module. If so, the module
will be called au1550_spi.
+config SPI_DAVINCI
+ tristate "SPI controller driver for DaVinci/DA8xx SoC's"
+ depends on SPI_MASTER && ARCH_DAVINCI
+ select SPI_BITBANG
+ help
+ SPI master controller for DaVinci and DA8xx SPI modules.
+
config SPI_BITBANG
tristate "Utilities for Bitbanging SPI masters"
help
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 3de408d..910ac6d 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_SH_SCI) += spi_sh_sci.o
+obj-$(CONFIG_SPI_DAVINCI) += davinci_spi.o
# ... add above this line ...
# SPI protocol drivers (device/link on bus)
diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c
new file mode 100644
index 0000000..a5b8e38
--- /dev/null
+++ b/drivers/spi/davinci_spi.c
@@ -0,0 +1,776 @@
+/*
+ * Copyright (C) 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+#include <mach/spi.h>
+
+#include "davinci_spi.h"
+
+
+static void davinci_spi_rx_buf_u8(u32 data, struct davinci_spi *davinci_spi)
+{
+ u8 *rx = davinci_spi->rx;
+
+ *rx++ = (u8)data;
+ davinci_spi->rx = rx;
+}
+
+static void davinci_spi_rx_buf_u16(u32 data, struct davinci_spi *davinci_spi)
+{
+ u16 *rx = davinci_spi->rx;
+
+ *rx++ = (u16)data;
+ davinci_spi->rx = rx;
+}
+
+static u32 davinci_spi_tx_buf_u8(struct davinci_spi *davinci_spi)
+{
+ u32 data;
+ const u8 *tx = davinci_spi->tx;
+
+ data = *tx++;
+ davinci_spi->tx = tx;
+ return data;
+}
+
+static u32 davinci_spi_tx_buf_u16(struct davinci_spi *davinci_spi)
+{
+ u32 data;
+ const u16 *tx = davinci_spi->tx;
+
+ data = *tx++;
+ davinci_spi->tx = tx;
+ return data;
+}
+
+static inline void set_io_bits(void __iomem *addr, u32 bits)
+{
+ u32 v = ioread32(addr);
+
+ v |= bits;
+ iowrite32(v, addr);
+}
+
+static inline void clear_io_bits(void __iomem *addr, u32 bits)
+{
+ u32 v = ioread32(addr);
+
+ v &= ~bits;
+ iowrite32(v, addr);
+}
+
+static inline void set_fmt_bits(void __iomem *addr, u32 bits, int cs_num)
+{
+ set_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits);
+}
+
+static inline void clear_fmt_bits(void __iomem *addr, u32 bits, int cs_num)
+{
+ clear_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits);
+}
+
+/*
+ * Interface to control the chip select signal
+ */
+static void davinci_spi_chipselect(struct spi_device *spi, int value)
+{
+ struct davinci_spi *davinci_spi;
+ struct davinci_spi_platform_data *pdata;
+
+ davinci_spi = spi_master_get_devdata(spi->master);
+ pdata = davinci_spi->pdata;
+
+ /* Called by spi_bitbang with:
+ * . CS_ACTIVE in start of transfer
+ * . CS_INACTIVE in end of transfer
+ * . CS_INACTIVE between chip select changes during a transfer
+ * to set up default clock polarity, and activate chip
+ * in davinci, CS lines are (de)activated per transfer by the CSNR
+ * field in SPIDAT1 and clock polarity is stored in the SPIFMTx per
+ * chip select, so nothing needs to be done in this function.
+ */
+
+}
+
+/*
+ * davinci_spi_setup_transfer - This functions will determine transfer method
+ * @spi: spi device on which data transfer to be done
+ * @t: spi transfer in which transfer info is filled
+ *
+ * This function determines data transfer method (8/16/32 bit transfer).
+ * It will also set the SPI Clock Control register according to
+ * SPI slave device freq.
+ */
+static int davinci_spi_setup_transfer(struct spi_device *spi,
+ struct spi_transfer *t)
+{
+
+ struct davinci_spi *davinci_spi;
+ struct davinci_spi_platform_data *pdata;
+ u8 bits_per_word = 0;
+ u32 hz = 0, prescale;
+
+ davinci_spi = spi_master_get_devdata(spi->master);
+ pdata = davinci_spi->pdata;
+
+ if (t) {
+ bits_per_word = t->bits_per_word;
+ hz = t->speed_hz;
+ }
+
+ /* if bits_per_word is not set then set it default */
+ if (!bits_per_word)
+ bits_per_word = spi->bits_per_word;
+
+ /*
+ * Assign function pointer to appropriate transfer method
+ * 8bit, 16bit or 32bit transfer
+ */
+ if (bits_per_word <= 8 && bits_per_word >= 2) {
+ davinci_spi->get_rx = davinci_spi_rx_buf_u8;
+ davinci_spi->get_tx = davinci_spi_tx_buf_u8;
+ davinci_spi->slave[spi->chip_select].bytes_per_word = 1;
+ } else if (bits_per_word <= 16 && bits_per_word >= 2) {
+ davinci_spi->get_rx = davinci_spi_rx_buf_u16;
+ davinci_spi->get_tx = davinci_spi_tx_buf_u16;
+ davinci_spi->slave[spi->chip_select].bytes_per_word = 2;
+ } else
+ return -EINVAL;
+
+ if (!hz)
+ hz = spi->max_speed_hz;
+
+ clear_fmt_bits(davinci_spi->base, SPIFMT_CHARLEN_MASK,
+ spi->chip_select);
+ set_fmt_bits(davinci_spi->base, bits_per_word & 0x1f,
+ spi->chip_select);
+
+ prescale = ((clk_get_rate(davinci_spi->clk) / hz) - 1) & 0xff;
+
+ clear_fmt_bits(davinci_spi->base, 0x0000ff00, spi->chip_select);
+ set_fmt_bits(davinci_spi->base, prescale << 8, spi->chip_select);
+
+ return 0;
+}
+
+/*
+ * davinci_spi_setup - This functions will set default transfer method
+ * @spi: spi device on which data transfer to be done
+ *
+ * This functions sets the default transfer method.
+ */
+
+static int davinci_spi_setup(struct spi_device *spi)
+{
+ int retval;
+ int op_mode = 0;
+ struct davinci_spi *davinci_spi;
+
+ davinci_spi = spi_master_get_devdata(spi->master);
+
+ /*
+ * Set up device-specific SPI configuration parameters.
+ * Most of these would normally be handled in spi_setup(),
+ * updating the per-chipselect FMT registers, but some of
+ * them use global controls like SPI_LOOP and SPI_READY.
+ */
+
+ if (spi->mode & SPI_LSB_FIRST)
+ set_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK,
+ spi->chip_select);
+
+ if (spi->mode & SPI_CPOL)
+ set_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK,
+ spi->chip_select);
+
+ if (!(spi->mode & SPI_CPHA))
+ set_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK,
+ spi->chip_select);
+
+ if (davinci_spi->version == SPI_VERSION_2) {
+ clear_fmt_bits(davinci_spi->base, SPIFMT_WDELAY_MASK,
+ spi->chip_select);
+ set_fmt_bits(davinci_spi->base,
+ (davinci_spi->pdata->wdelay
+ << SPIFMT_WDELAY_SHIFT)
+ & SPIFMT_WDELAY_MASK,
+ spi->chip_select);
+
+ if (davinci_spi->pdata->odd_parity)
+ set_fmt_bits(davinci_spi->base,
+ SPIFMT_ODD_PARITY_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base,
+ SPIFMT_ODD_PARITY_MASK,
+ spi->chip_select);
+
+ if (davinci_spi->pdata->parity_enable)
+ set_fmt_bits(davinci_spi->base,
+ SPIFMT_PARITYENA_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base,
+ SPIFMT_PARITYENA_MASK,
+ spi->chip_select);
+
+ if (davinci_spi->pdata->wait_enable)
+ set_fmt_bits(davinci_spi->base,
+ SPIFMT_WAITENA_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base,
+ SPIFMT_WAITENA_MASK,
+ spi->chip_select);
+
+ if (davinci_spi->pdata->timer_disable)
+ set_fmt_bits(davinci_spi->base,
+ SPIFMT_DISTIMER_MASK,
+ spi->chip_select);
+ else
+ clear_fmt_bits(davinci_spi->base,
+ SPIFMT_DISTIMER_MASK,
+ spi->chip_select);
+ }
+
+ if (spi->mode & SPI_CS_HIGH)
+ set_io_bits(davinci_spi->base + SPIDEF, 1<<spi->chip_select);
+ else
+ clear_io_bits(davinci_spi->base + SPIDEF, 1<<spi->chip_select);
+
+ /*
+ * Version 1 hardware supports two basic SPI modes:
+ * - Standard SPI mode uses 4 pins, with chipselect
+ * - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS)
+ * (distinct from SPI_3WIRE, with just one data wire;
+ * or similar variants without MOSI or without MISO)
+ *
+ * Version 2 hardware supports an optional handshaking signal,
+ * so it can support two more modes:
+ * - 5 pin SPI variant is standard SPI plus SPI_READY
+ * - 4 pin with enable is (SPI_READY | SPI_NO_CS)
+ */
+
+ /* Read op mode - so don't touch bits controlling other chip selects */
+ op_mode = ioread32(davinci_spi->base + SPIPC0);
+
+ op_mode |= SPIPC0_DIFUN_MASK
+ | SPIPC0_DOFUN_MASK
+ | SPIPC0_CLKFUN_MASK;
+
+ if (!(spi->mode & SPI_NO_CS)) {
+ /* enable chip select line for given chip select */
+ op_mode |= 1 << spi->chip_select;
+ } else {
+ /* disable chip select line for given chip select */
+ op_mode &= ~(1L << spi->chip_select);
+ }
+
+ /* Note that on version 1 this field must be written with zeros */
+ if (davinci_spi->version == SPI_VERSION_2 && spi->mode & SPI_READY)
+ op_mode |= SPIPC0_SPIENA_MASK;
+
+ iowrite32(op_mode, davinci_spi->base + SPIPC0);
+
+ if (spi->mode & SPI_LOOP)
+ set_io_bits(davinci_spi->base + SPIGCR1,
+ SPIGCR1_LOOPBACK_MASK);
+ else
+ clear_io_bits(davinci_spi->base + SPIGCR1,
+ SPIGCR1_LOOPBACK_MASK);
+
+ /* if bits per word length is zero then set it default 8 */
+ if (!spi->bits_per_word)
+ spi->bits_per_word = 8;
+
+ /*
+ * SPI in DaVinci and DA8xx operate between
+ * 600 KHz and 50 MHz
+ */
+ if (spi->max_speed_hz < 600000 || spi->max_speed_hz > 50000000)
+ return -EINVAL;
+
+ retval = davinci_spi_setup_transfer(spi, NULL);
+
+ return retval;
+}
+
+static int davinci_spi_check_error(struct davinci_spi *davinci_spi,
+ int int_status)
+{
+ struct device *sdev = davinci_spi->bitbang.master->dev.parent;
+ int supported_flags = 0;
+
+ switch (davinci_spi->version) {
+ case SPI_VERSION_1:
+ supported_flags = SPIFLG_VERSION_1; break;
+ case SPI_VERSION_2:
+ supported_flags = SPIFLG_VERSION_2; break;
+ case SPI_VERSION_3:
+ supported_flags = SPIFLG_VERSION_3; break;
+ }
+
+ if (int_status & supported_flags & SPIFLG_TIMEOUT_MASK) {
+ dev_dbg(sdev, "SPI Time-out Error\n");
+ return -ETIMEDOUT;
+ }
+
+ if (int_status & supported_flags & SPIFLG_DESYNC_MASK) {
+ dev_dbg(sdev, "SPI Desynchronization Error\n");
+ return -EIO;
+ }
+
+ if (int_status & supported_flags & SPIFLG_BITERR_MASK) {
+ dev_dbg(sdev, "SPI Bit error\n");
+ return -EIO;
+ }
+
+ if (int_status & supported_flags & SPIFLG_DLEN_ERR_MASK) {
+ dev_dbg(sdev, "SPI Data Length Error\n");
+ return -EIO;
+ }
+
+ if (int_status & supported_flags & SPIFLG_PARERR_MASK) {
+ dev_dbg(sdev, "SPI Parity Error\n");
+ return -EIO;
+ }
+
+ if (int_status & supported_flags & SPIFLG_TX_INTR_MASK) {
+ dev_dbg(sdev, "SPI TX intr bit set\n");
+ return -EIO;
+ }
+
+ if (int_status & supported_flags & SPIFLG_BUF_INIT_ACTIVE_MASK) {
+ dev_dbg(sdev, "SPI Buffer Init Active\n");
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+/*
+ * davinci_spi_bufs - functions which will handle transfer data
+ * @spi: spi device on which data transfer to be done
+ * @t: spi transfer in which transfer info is filled
+ *
+ * This function will put data to be transferred into data register
+ * of SPI controller and then wait untill the completion will be marked
+ * by the IRQ Handler.
+ */
+static int davinci_spi_bufs_pio(struct spi_device *spi, struct spi_transfer *t)
+{
+ /* Note this function was called after chipselect(CS_ACTIVE) or after
+ * another transfer */
+
+ struct davinci_spi *davinci_spi;
+ int int_status, count, ret;
+ u8 conv, tmp;
+ u32 tx_data, data1_reg_val;
+ u32 buf_val, flg_val;
+ struct davinci_spi_platform_data *pdata;
+
+ davinci_spi = spi_master_get_devdata(spi->master);
+ pdata = davinci_spi->pdata;
+
+ davinci_spi->tx = t->tx_buf;
+ davinci_spi->rx = t->rx_buf;
+
+ /* convert len to words bbased on bits_per_word */
+ conv = davinci_spi->slave[spi->chip_select].bytes_per_word;
+ davinci_spi->count = t->len / conv;
+
+ INIT_COMPLETION(davinci_spi->done);
+
+ /* Enable SPI */
+ set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK);
+
+ count = davinci_spi->count;
+ data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT;
+
+ /* Set current chip select. CSNR's value is tied to both chip selects
+ * default value (as set in SPIDEF) - set per chip with CS_HIGH mode.
+ */
+ tmp = ioread32(davinci_spi->base + SPIDEF);
+ tmp = (1<<spi->chip_select) ^ (tmp & 3);
+ data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT;
+
+ /* Set current data format (one per chip select) */
+ data1_reg_val |= spi->chip_select << SPIDAT1_DFSEL_SHIFT;
+
+ /* Wait for spi to be ready (wait until no data is received) */
+ while ((ioread32(davinci_spi->base + SPIBUF) &
+ SPIBUF_RXEMPTY_MASK) == 0)
+ cpu_relax();
+
+ /* Determine the command to execute READ or WRITE */
+ if (t->tx_buf) {
+ clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL);
+
+ while (1) {
+ tx_data = davinci_spi->get_tx(davinci_spi);
+
+ data1_reg_val &= ~(0xFFFF);
+ data1_reg_val |= (0xFFFF & tx_data);
+
+ buf_val = ioread32(davinci_spi->base + SPIBUF);
+ if ((buf_val & SPIBUF_TXFULL_MASK) == 0) {
+ iowrite32(data1_reg_val,
+ davinci_spi->base + SPIDAT1);
+ count--;
+ }
+
+ while ((buf_val = ioread32(davinci_spi->base + SPIBUF))
+ & SPIBUF_RXEMPTY_MASK)
+ cpu_relax();
+
+ /* getting the returned byte */
+ if (t->rx_buf)
+ davinci_spi->get_rx(buf_val, davinci_spi);
+
+ if (count <= 0)
+ break;
+ }
+ } else {
+ if (pdata->poll_mode) {
+ while (1) {
+ /* keeps the serial clock going (write zeros) */
+ if ((ioread32(davinci_spi->base + SPIBUF)
+ & SPIBUF_TXFULL_MASK) == 0)
+ iowrite32(data1_reg_val,
+ davinci_spi->base + SPIDAT1);
+
+ while ((buf_val = ioread32(davinci_spi->base +
+ SPIBUF)) & SPIBUF_RXEMPTY_MASK)
+ cpu_relax();
+
+ flg_val = ioread32(davinci_spi->base + SPIFLG);
+
+ davinci_spi->get_rx(buf_val, davinci_spi);
+
+ count--;
+ if (count <= 0)
+ break;
+ }
+ } else { /* Receive in Interrupt mode */
+ int i;
+
+ for (i = 0; i < davinci_spi->count; i++) {
+ set_io_bits(davinci_spi->base + SPIINT,
+ SPIINT_BITERR_INTR
+ | SPIINT_OVRRUN_INTR
+ | SPIINT_RX_INTR);
+
+ iowrite32(data1_reg_val,
+ davinci_spi->base + SPIDAT1);
+
+ while (ioread32(davinci_spi->base + SPIINT) &
+ SPIINT_RX_INTR)
+ cpu_relax();
+ }
+ iowrite32((data1_reg_val & 0x0ffcffff),
+ davinci_spi->base + SPIDAT1);
+ }
+ }
+
+ /*
+ * Check for bit error, desync error,parity error,timeout error and
+ * receive overflow errors
+ */
+ int_status = ioread32(davinci_spi->base + SPIFLG);
+
+ ret = davinci_spi_check_error(davinci_spi, int_status);
+ if (ret != 0)
+ return ret;
+
+ /* SPI Framework maintains the count only in bytes so convert back */
+ davinci_spi->count *= conv;
+
+ return t->len;
+}
+
+/*
+ * davinci_spi_irq - probe function for SPI Master Controller
+ * @irq: IRQ number for this SPI Master
+ * @context_data: structure for SPI Master controller davinci_spi
+ *
+ * ISR will determine that interrupt arrives either for READ or WRITE command.
+ * According to command it will do the appropriate action. It will check
+ * transfer length and if it is not zero then dispatch transfer command again.
+ * If transfer length is zero then it will indicate the COMPLETION so that
+ * davinci_spi_bufs function can go ahead.
+ */
+static irqreturn_t davinci_spi_irq(s32 irq, void *context_data)
+{
+ struct davinci_spi *davinci_spi = context_data;
+ u32 int_status, rx_data = 0;
+ irqreturn_t ret = IRQ_NONE;
+
+ int_status = ioread32(davinci_spi->base + SPIFLG);
+ while ((int_status & SPIFLG_MASK) != 0) {
+ ret = IRQ_HANDLED;
+
+ if (likely(int_status & SPIFLG_RX_INTR_MASK)) {
+ rx_data = ioread32(davinci_spi->base + SPIBUF);
+ davinci_spi->get_rx(rx_data, davinci_spi);
+
+ /* Disable Receive Interrupt */
+ iowrite32(~SPIINT_RX_INTR,
+ davinci_spi->base + SPIINT);
+ } else
+ (void)davinci_spi_check_error(davinci_spi, int_status);
+
+ int_status = ioread32(davinci_spi->base + SPIFLG);
+ }
+
+ return ret;
+}
+
+/*
+ * davinci_spi_probe - probe function for SPI Master Controller
+ * @pdev: platform_device structure which contains plateform specific data
+ *
+ * According to Linux Device Model this function will be invoked by Linux
+ * with plateform_device struct which contains the device specific info.
+ * This function will map the SPI controller's memory, register IRQ,
+ * Reset SPI controller and setting its registers to default value.
+ * It will invoke spi_bitbang_start to create work queue so that client driver
+ * can register transfer method to work queue.
+ */
+static int davinci_spi_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct davinci_spi *davinci_spi;
+ struct davinci_spi_platform_data *pdata;
+ struct resource *r, *mem;
+ int ret = 0;
+
+ pdata = pdev->dev.platform_data;
+ if (pdata == NULL) {
+ ret = -ENODEV;
+ goto err;
+ }
+
+ master = spi_alloc_master(&pdev->dev, sizeof(struct davinci_spi));
+ if (master == NULL) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ dev_set_drvdata(&pdev->dev, master);
+
+ davinci_spi = spi_master_get_devdata(master);
+ if (davinci_spi == NULL) {
+ ret = -ENOENT;
+ goto free_master;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ ret = -ENOENT;
+ goto free_master;
+ }
+
+ davinci_spi->pbase = r->start;
+ davinci_spi->region_size = resource_size(r);
+ davinci_spi->pdata = pdata;
+
+ mem = request_mem_region(r->start, davinci_spi->region_size,
+ pdev->name);
+ if (mem == NULL) {
+ ret = -EBUSY;
+ goto free_master;
+ }
+
+ davinci_spi->base = (struct davinci_spi_reg __iomem *)
+ ioremap(r->start, davinci_spi->region_size);
+ if (davinci_spi->base == NULL) {
+ ret = -ENOMEM;
+ goto release_region;
+ }
+
+ davinci_spi->irq = platform_get_irq(pdev, 0);
+ if (davinci_spi->irq <= 0) {
+ ret = -EINVAL;
+ goto unmap_io;
+ }
+
+ ret = request_irq(davinci_spi->irq, davinci_spi_irq, IRQF_DISABLED,
+ dev_name(&pdev->dev), davinci_spi);
+ if (ret != 0) {
+ ret = -EAGAIN;
+ goto unmap_io;
+ }
+
+ davinci_spi->bitbang.master = spi_master_get(master);
+ if (davinci_spi->bitbang.master == NULL) {
+ ret = -ENODEV;
+ goto err1;
+ }
+
+ davinci_spi->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(davinci_spi->clk)) {
+ ret = -ENODEV;
+ goto put_master;
+ }
+ clk_enable(davinci_spi->clk);
+
+
+ master->bus_num = pdev->id;
+ master->num_chipselect = pdata->num_chipselect;
+ master->setup = davinci_spi_setup;
+
+ davinci_spi->bitbang.chipselect = davinci_spi_chipselect;
+ davinci_spi->bitbang.setup_transfer = davinci_spi_setup_transfer;
+ davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_pio;
+
+ davinci_spi->bitbang.flags =
+ SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP | SPI_CS_HIGH;
+
+ if (davinci_spi->version == SPI_VERSION_2)
+ davinci_spi->bitbang.flags |= SPI_READY;
+
+ davinci_spi->version = pdata->version;
+ davinci_spi->get_rx = davinci_spi_rx_buf_u8;
+ davinci_spi->get_tx = davinci_spi_tx_buf_u8;
+
+ init_completion(&davinci_spi->done);
+
+ /* Reset In/OUT SPI modle */
+ iowrite32(0, davinci_spi->base + SPIGCR0);
+ udelay(100);
+ iowrite32(1, davinci_spi->base + SPIGCR0);
+
+ /* Set global SPI parameters */
+
+ /* Clock internal */
+ if (davinci_spi->pdata->clk_internal)
+ set_io_bits(davinci_spi->base + SPIGCR1,
+ SPIGCR1_CLKMOD_MASK);
+ else
+ clear_io_bits(davinci_spi->base + SPIGCR1,
+ SPIGCR1_CLKMOD_MASK);
+
+ /* master mode default */
+ set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK);
+
+ if (davinci_spi->pdata->intr_level)
+ iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL);
+ else
+ iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL);
+
+ /* c2t and t2c delays */
+ iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) |
+ (pdata->t2cdelay << SPI_T2CDELAY_SHIFT),
+ davinci_spi->base + SPIDELAY);
+
+
+ ret = spi_bitbang_start(&davinci_spi->bitbang);
+ if (ret != 0)
+ goto free_clk;
+
+ dev_info(&pdev->dev, "Controller at 0x%p (irq = %d) \n",
+ davinci_spi->base, davinci_spi->irq);
+
+ return ret;
+
+free_clk:
+ clk_disable(davinci_spi->clk);
+ clk_put(davinci_spi->clk);
+put_master:
+ spi_master_put(master);
+err1:
+ free_irq(davinci_spi->irq, davinci_spi);
+unmap_io:
+ iounmap(davinci_spi->base);
+release_region:
+ release_mem_region(davinci_spi->pbase, davinci_spi->region_size);
+free_master:
+ kfree(master);
+err:
+ return ret;
+}
+
+/*
+ * davinci_spi_remove - remove function for SPI Master Controller
+ * @pdev: platform_device structure which contains plateform specific data
+ *
+ * This function will do the reverse action of davinci_spi_probe function
+ * It will free the IRQ and SPI controller's memory region.
+ * It will also call spi_bitbang_stop to destroy the work queue which was
+ * created by spi_bitbang_start.
+ */
+static int __exit davinci_spi_remove(struct platform_device *pdev)
+{
+ struct davinci_spi *davinci_spi;
+ struct spi_master *master;
+
+ master = dev_get_drvdata(&pdev->dev);
+ davinci_spi = spi_master_get_devdata(master);
+
+ spi_bitbang_stop(&davinci_spi->bitbang);
+
+ clk_disable(davinci_spi->clk);
+ clk_put(davinci_spi->clk);
+ spi_master_put(master);
+ free_irq(davinci_spi->irq, davinci_spi);
+ iounmap(davinci_spi->base);
+ release_mem_region(davinci_spi->pbase, davinci_spi->region_size);
+
+ return 0;
+}
+
+static struct platform_driver davinci_spi_driver = {
+ .driver.name = "spi_davinci",
+ .remove = __exit_p(davinci_spi_remove),
+};
+
+static int __init davinci_spi_init(void)
+{
+ return platform_driver_probe(&davinci_spi_driver, davinci_spi_probe);
+}
+
+static void __exit davinci_spi_exit(void)
+{
+ platform_driver_unregister(&davinci_spi_driver);
+}
+
+module_init(davinci_spi_init);
+module_exit(davinci_spi_exit);
+
+MODULE_DESCRIPTION("TI DaVinci SPI Master Controller Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/spi/davinci_spi.h b/drivers/spi/davinci_spi.h
new file mode 100644
index 0000000..6c326c2
--- /dev/null
+++ b/drivers/spi/davinci_spi.h
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __DAVINCI_SPI_H
+#define __DAVINCI_SPI_H
+
+#define SPI_MAX_CHIPSELECT 2
+
+#define CS_DEFAULT 0xFF
+#define SCS0_SELECT 0x01
+#define SCS1_SELECT 0x02
+#define SCS2_SELECT 0x04
+#define SCS3_SELECT 0x08
+#define SCS4_SELECT 0x10
+#define SCS5_SELECT 0x20
+#define SCS6_SELECT 0x40
+#define SCS7_SELECT 0x80
+
+#define SPIFMT_PHASE_MASK BIT(16)
+#define SPIFMT_POLARITY_MASK BIT(17)
+#define SPIFMT_DISTIMER_MASK BIT(18)
+#define SPIFMT_SHIFTDIR_MASK BIT(20)
+#define SPIFMT_WAITENA_MASK BIT(21)
+#define SPIFMT_PARITYENA_MASK BIT(22)
+#define SPIFMT_ODD_PARITY_MASK BIT(23)
+#define SPIFMT_WDELAY_MASK 0x3f000000u
+#define SPIFMT_WDELAY_SHIFT 24
+#define SPIFMT_CHARLEN_MASK 0x0000001Fu
+
+/* SPIGCR1 */
+#define SPIGCR1_SPIENA_MASK 0x01000000u
+#define SPIGCR1_CLKMOD_MASK BIT(1)
+#define SPIGCR1_MASTER_MASK BIT(0)
+#define SPIGCR1_LOOPBACK_MASK BIT(16)
+
+/* SPIPC0 */
+#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */
+#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */
+#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */
+#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */
+#define SPIPC0_EN1FUN_MASK BIT(1)
+#define SPIPC0_EN0FUN_MASK BIT(0)
+
+#define SPIINT_MASKALL 0x0101035F
+#define SPI_INTLVL_1 0x000001FFu
+#define SPI_INTLVL_0 0x00000000u
+
+/* SPIDAT1 */
+#define SPIDAT1_CSHOLD_MASK BIT(28)
+#define SPIDAT1_CSHOLD_SHIFT 28
+#define SPIDAT1_CSNR_MASK (BIT(17 | BIT(16))
+#define SPIDAT1_CSNR_SHIFT 16
+#define SPIDAT1_DFSEL_MASK (BIT(24 | BIT(25))
+#define SPIDAT1_DFSEL_SHIFT 24
+
+/* SPIBUF */
+#define SPIBUF_TXFULL_MASK BIT(29)
+#define SPIBUF_RXEMPTY_MASK BIT(31)
+
+/* Error Masks */
+#define SPIFLG_DLEN_ERR_MASK BIT(0)
+#define SPIFLG_TIMEOUT_MASK BIT(1)
+#define SPIFLG_PARERR_MASK BIT(2)
+#define SPIFLG_DESYNC_MASK BIT(3)
+#define SPIFLG_BITERR_MASK BIT(4)
+#define SPIFLG_OVRRUN_MASK BIT(6)
+#define SPIFLG_RX_INTR_MASK BIT(8)
+#define SPIFLG_TX_INTR_MASK BIT(9)
+#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24)
+#define SPIFLG_MASK (SPIFLG_DLEN_ERR_MASK \
+ | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \
+ | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \
+ | SPIFLG_OVRRUN_MASK | SPIFLG_RX_INTR_MASK \
+ | SPIFLG_TX_INTR_MASK \
+ | SPIFLG_BUF_INIT_ACTIVE_MASK)
+
+
+#define SPIFLG_VERSION_1 (SPIFLG_TIMEOUT_MASK | SPIFLG_DESYNC_MASK \
+ | SPIFLG_BITERR_MASK | SPIFLG_RX_INTR_MASK)
+
+#define SPIFLG_VERSION_2 (SPIFLG_DLEN_ERR_MASK | SPIFLG_TIMEOUT_MASK \
+ | SPIFLG_PARERR_MASK | SPIFLG_DESYNC_MASK \
+ | SPIFLG_BITERR_MASK | SPIFLG_DESYNC_MASK \
+ | SPIFLG_RX_INTR_MASK | SPIFLG_TX_INTR_MASK \
+ | SPIFLG_BUF_INIT_ACTIVE_MASK)
+
+#define SPIFLG_VERSION_3 (SPIFLG_BITERR_MASK | SPIFLG_OVRRUN_MASK \
+ | SPIFLG_RX_INTR_MASK)
+
+
+#define SPIINT_DLEN_ERR_INTR BIT(0)
+#define SPIINT_TIMEOUT_INTR BIT(1)
+#define SPIINT_PARERR_INTR BIT(2)
+#define SPIINT_DESYNC_INTR BIT(3)
+#define SPIINT_BITERR_INTR BIT(4)
+#define SPIINT_OVRRUN_INTR BIT(6)
+#define SPIINT_RX_INTR BIT(8)
+#define SPIINT_TX_INTR BIT(9)
+#define SPIINT_DMA_REQ_EN BIT(16)
+#define SPIINT_ENABLE_HIGHZ BIT(24)
+
+#define SPI_T2CDELAY_SHIFT 16
+#define SPI_C2TDELAY_SHIFT 24
+
+/* SPI Controller registers */
+#define SPIGCR0 0x00
+#define SPIGCR1 0x04
+#define SPIINT 0x08
+#define SPILVL 0x0c
+#define SPIFLG 0x10
+#define SPIPC0 0x14
+#define SPIPC1 0x18
+#define SPIPC2 0x1c
+#define SPIPC3 0x20
+#define SPIPC4 0x24
+#define SPIPC5 0x28
+#define SPIPC6 0x2c
+#define SPIPC7 0x30
+#define SPIPC8 0x34
+#define SPIDAT0 0x38
+#define SPIDAT1 0x3c
+#define SPIBUF 0x40
+#define SPIEMU 0x44
+#define SPIDELAY 0x48
+#define SPIDEF 0x4c
+#define SPIFMT0 0x50
+#define SPIFMT1 0x54
+#define SPIFMT2 0x58
+#define SPIFMT3 0x5c
+#define TGINTVEC0 0x60
+#define TGINTVEC1 0x64
+
+struct davinci_spi_slave {
+ u32 cmd_to_write;
+ u32 clk_ctrl_to_write;
+ u32 bytes_per_word;
+ u8 active_cs;
+};
+
+/* SPI Controller driver's private data. */
+struct davinci_spi {
+ struct spi_bitbang bitbang;
+ struct clk *clk;
+
+ u8 version;
+ resource_size_t pbase;
+ void __iomem *base;
+ size_t region_size;
+ u32 irq;
+ struct completion done;
+
+ const void *tx;
+ void *rx;
+ int count;
+ struct davinci_spi_platform_data *pdata;
+
+ void (*get_rx)(u32 rx_data, struct davinci_spi *);
+ u32 (*get_tx)(struct davinci_spi *);
+
+ struct davinci_spi_slave slave[SPI_MAX_CHIPSELECT];
+};
+
+#endif /* __DAVINCI_SPI_H */
--
1.5.4.3
--
Pablo Bitton <pablo.bitton@...il.com>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists