| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Mon, 14 Sep 2009 16:08:13 -0400
From: Mike Frysinger <vapier@...too.org>
To: linux-kernel@...r.kernel.org
Cc: uclinux-dist-devel@...ckfin.uclinux.org,
Harald Krapfenbauer <Harald.Krapfenbauer@...etechnix.at>
Subject: [PATCH 69/72] Blackfin: cm-bf537u: split board from cm-bf537e
From: Harald Krapfenbauer <Harald.Krapfenbauer@...etechnix.at>
The cm-bf537u module, while similar to the cm-bf537e, is different enough
to warrant its own resources. It has a USB controller but no PHY.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@...etechnix.at>
Signed-off-by: Mike Frysinger <vapier@...too.org>
---
arch/blackfin/Kconfig | 7 +-
arch/blackfin/mach-bf537/boards/Kconfig | 12 +-
arch/blackfin/mach-bf537/boards/Makefile | 3 +-
arch/blackfin/mach-bf537/boards/cm_bf537.c | 632 -----------------------
arch/blackfin/mach-bf537/boards/cm_bf537e.c | 727 +++++++++++++++++++++++++++
arch/blackfin/mach-bf537/boards/cm_bf537u.c | 633 +++++++++++++++++++++++
6 files changed, 1375 insertions(+), 639 deletions(-)
delete mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537.c
create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537e.c
create mode 100644 arch/blackfin/mach-bf537/boards/cm_bf537u.c
diff --git a/arch/blackfin/Kconfig b/arch/blackfin/Kconfig
index f20dc77..e7a781d 100644
--- a/arch/blackfin/Kconfig
+++ b/arch/blackfin/Kconfig
@@ -342,8 +342,9 @@ config MEM_MT48LC64M4A2FB_7E
config MEM_MT48LC16M16A2TG_75
bool
depends on (BFIN533_EZKIT || BFIN561_EZKIT \
- || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM \
- || H8606_HVSISTEMAS || BFIN527_BLUETECHNIX_CM)
+ || BFIN533_BLUETECHNIX_CM || BFIN537_BLUETECHNIX_CM_E \
+ || BFIN537_BLUETECHNIX_CM_U || H8606_HVSISTEMAS \
+ || BFIN527_BLUETECHNIX_CM)
default y
config MEM_MT48LC32M8A2_75
@@ -459,7 +460,7 @@ config VCO_MULT
default "45" if BFIN533_STAMP
default "20" if (BFIN537_STAMP || BFIN527_EZKIT || BFIN548_EZKIT || BFIN548_BLUETECHNIX_CM || BFIN538_EZKIT)
default "22" if BFIN533_BLUETECHNIX_CM
- default "20" if (BFIN537_BLUETECHNIX_CM || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
+ default "20" if (BFIN537_BLUETECHNIX_CM_E || BFIN537_BLUETECHNIX_CM_U || BFIN527_BLUETECHNIX_CM || BFIN561_BLUETECHNIX_CM)
default "20" if BFIN561_EZKIT
default "16" if (H8606_HVSISTEMAS || BLACKSTAMP || BFIN526_EZBRD || BFIN518F_EZBRD)
help
diff --git a/arch/blackfin/mach-bf537/boards/Kconfig b/arch/blackfin/mach-bf537/boards/Kconfig
index 77c59da..44132fd 100644
--- a/arch/blackfin/mach-bf537/boards/Kconfig
+++ b/arch/blackfin/mach-bf537/boards/Kconfig
@@ -9,11 +9,17 @@ config BFIN537_STAMP
help
BF537-STAMP board support.
-config BFIN537_BLUETECHNIX_CM
- bool "Bluetechnix CM-BF537"
+config BFIN537_BLUETECHNIX_CM_E
+ bool "Bluetechnix CM-BF537E"
depends on (BF537)
help
- CM-BF537 support for EVAL- and DEV-Board.
+ CM-BF537E support for EVAL- and DEV-Board.
+
+config BFIN537_BLUETECHNIX_CM_U
+ bool "Bluetechnix CM-BF537U"
+ depends on (BF537)
+ help
+ CM-BF537U support for EVAL- and DEV-Board.
config BFIN537_BLUETECHNIX_TCM
bool "Bluetechnix TCM-BF537"
diff --git a/arch/blackfin/mach-bf537/boards/Makefile b/arch/blackfin/mach-bf537/boards/Makefile
index 68b98a7..7e6aa4e 100644
--- a/arch/blackfin/mach-bf537/boards/Makefile
+++ b/arch/blackfin/mach-bf537/boards/Makefile
@@ -3,7 +3,8 @@
#
obj-$(CONFIG_BFIN537_STAMP) += stamp.o
-obj-$(CONFIG_BFIN537_BLUETECHNIX_CM) += cm_bf537.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_E) += cm_bf537e.o
+obj-$(CONFIG_BFIN537_BLUETECHNIX_CM_U) += cm_bf537u.o
obj-$(CONFIG_BFIN537_BLUETECHNIX_TCM) += tcm_bf537.o
obj-$(CONFIG_PNAV10) += pnav10.o
obj-$(CONFIG_CAMSIG_MINOTAUR) += minotaur.o
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537.c b/arch/blackfin/mach-bf537/boards/cm_bf537.c
deleted file mode 100644
index 220cfda..0000000
--- a/arch/blackfin/mach-bf537/boards/cm_bf537.c
+++ /dev/null
@@ -1,632 +0,0 @@
-/*
- * File: arch/blackfin/mach-bf537/boards/cm_bf537.c
- * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
- * Author: Aidan Williams <aidan@...ta.com.au>
- *
- * Created: 2005
- * Description: Board description file
- *
- * Modified:
- * Copyright 2005 National ICT Australia (NICTA)
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Bugs: Enter bugs at http://blackfin.uclinux.org/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see the file COPYING, or write
- * to the Free Software Foundation, Inc.,
- * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/device.h>
-#include <linux/etherdevice.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/flash.h>
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-#include <linux/usb/isp1362.h>
-#endif
-#include <linux/ata_platform.h>
-#include <linux/irq.h>
-#include <asm/dma.h>
-#include <asm/bfin5xx_spi.h>
-#include <asm/portmux.h>
-#include <asm/dpmc.h>
-
-/*
- * Name the Board for the /proc/cpuinfo
- */
-const char bfin_board_name[] = "Bluetechnix CM BF537";
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
-/* all SPI peripherals info goes here */
-
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
-static struct mtd_partition bfin_spi_flash_partitions[] = {
- {
- .name = "bootloader(spi)",
- .size = 0x00020000,
- .offset = 0,
- .mask_flags = MTD_CAP_ROM
- }, {
- .name = "linux kernel(spi)",
- .size = 0xe0000,
- .offset = 0x20000
- }, {
- .name = "file system(spi)",
- .size = 0x700000,
- .offset = 0x00100000,
- }
-};
-
-static struct flash_platform_data bfin_spi_flash_data = {
- .name = "m25p80",
- .parts = bfin_spi_flash_partitions,
- .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
- .type = "m25p64",
-};
-
-/* SPI flash chip (m25p64) */
-static struct bfin5xx_spi_chip spi_flash_chip_info = {
- .enable_dma = 0, /* use dma transfer with this chip*/
- .bits_per_word = 8,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
-/* SPI ADC chip */
-static struct bfin5xx_spi_chip spi_adc_chip_info = {
- .enable_dma = 1, /* use dma transfer with this chip*/
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
-static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 16,
-};
-#endif
-
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
-static struct bfin5xx_spi_chip mmc_spi_chip_info = {
- .enable_dma = 0,
- .bits_per_word = 8,
-};
-#endif
-
-static struct spi_board_info bfin_spi_board_info[] __initdata = {
-#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
- {
- /* the modalias must be the same as spi device driver name */
- .modalias = "m25p80", /* Name of spi_driver for this device */
- .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
- .platform_data = &bfin_spi_flash_data,
- .controller_data = &spi_flash_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-
-#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
- {
- .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
- .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0, /* Framework bus number */
- .chip_select = 1, /* Framework chip select. */
- .platform_data = NULL, /* No spi_driver specific config */
- .controller_data = &spi_adc_chip_info,
- },
-#endif
-
-#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
- {
- .modalias = "ad1836",
- .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
- .controller_data = &ad1836_spi_chip_info,
- },
-#endif
-
-#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
- {
- .modalias = "mmc_spi",
- .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 1,
- .controller_data = &mmc_spi_chip_info,
- .mode = SPI_MODE_3,
- },
-#endif
-};
-
-/* SPI (0) */
-static struct resource bfin_spi0_resource[] = {
- [0] = {
- .start = SPI0_REGBASE,
- .end = SPI0_REGBASE + 0xFF,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = CH_SPI,
- .end = CH_SPI,
- .flags = IORESOURCE_DMA,
- },
- [2] = {
- .start = IRQ_SPI,
- .end = IRQ_SPI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-/* SPI controller data */
-static struct bfin5xx_spi_master bfin_spi0_info = {
- .num_chipselect = 8,
- .enable_dma = 1, /* master has the ability to do dma transfer */
- .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
-};
-
-static struct platform_device bfin_spi0_device = {
- .name = "bfin-spi",
- .id = 0, /* Bus number */
- .num_resources = ARRAY_SIZE(bfin_spi0_resource),
- .resource = bfin_spi0_resource,
- .dev = {
- .platform_data = &bfin_spi0_info, /* Passed to driver */
- },
-};
-#endif /* spi master and devices */
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
-static struct platform_device rtc_device = {
- .name = "rtc-bfin",
- .id = -1,
-};
-#endif
-
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
-static struct platform_device hitachi_fb_device = {
- .name = "hitachi-tx09",
-};
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-#include <linux/smc91x.h>
-
-static struct smc91x_platdata smc91x_info = {
- .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
- .leda = RPC_LED_100_10,
- .ledb = RPC_LED_TX_RX,
-};
-
-static struct resource smc91x_resources[] = {
- {
- .start = 0x20200300,
- .end = 0x20200300 + 16,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PF14,
- .end = IRQ_PF14,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct platform_device smc91x_device = {
- .name = "smc91x",
- .id = 0,
- .num_resources = ARRAY_SIZE(smc91x_resources),
- .resource = smc91x_resources,
- .dev = {
- .platform_data = &smc91x_info,
- },
-};
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
-static struct resource isp1362_hcd_resources[] = {
- {
- .start = 0x20308000,
- .end = 0x20308000,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0x20308004,
- .end = 0x20308004,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PG15,
- .end = IRQ_PG15,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct isp1362_platform_data isp1362_priv = {
- .sel15Kres = 1,
- .clknotstop = 0,
- .oc_enable = 0,
- .int_act_high = 0,
- .int_edge_triggered = 0,
- .remote_wakeup_connected = 0,
- .no_power_switching = 1,
- .power_switching_mode = 0,
-};
-
-static struct platform_device isp1362_hcd_device = {
- .name = "isp1362-hcd",
- .id = 0,
- .dev = {
- .platform_data = &isp1362_priv,
- },
- .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
- .resource = isp1362_hcd_resources,
-};
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
-static struct resource net2272_bfin_resources[] = {
- {
- .start = 0x20200000,
- .end = 0x20200000 + 0x100,
- .flags = IORESOURCE_MEM,
- }, {
- .start = IRQ_PH14,
- .end = IRQ_PH14,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
- },
-};
-
-static struct platform_device net2272_bfin_device = {
- .name = "net2272",
- .id = -1,
- .num_resources = ARRAY_SIZE(net2272_bfin_resources),
- .resource = net2272_bfin_resources,
-};
-#endif
-
-static struct resource bfin_gpios_resources = {
- .start = 0,
- .end = MAX_BLACKFIN_GPIOS - 1,
- .flags = IORESOURCE_IRQ,
-};
-
-static struct platform_device bfin_gpios_device = {
- .name = "simple-gpio",
- .id = -1,
- .num_resources = 1,
- .resource = &bfin_gpios_resources,
-};
-
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
-static struct mtd_partition cm_partitions[] = {
- {
- .name = "bootloader(nor)",
- .size = 0x40000,
- .offset = 0,
- }, {
- .name = "linux kernel(nor)",
- .size = 0xE0000,
- .offset = MTDPART_OFS_APPEND,
- }, {
- .name = "file system(nor)",
- .size = MTDPART_SIZ_FULL,
- .offset = MTDPART_OFS_APPEND,
- }
-};
-
-static struct physmap_flash_data cm_flash_data = {
- .width = 2,
- .parts = cm_partitions,
- .nr_parts = ARRAY_SIZE(cm_partitions),
-};
-
-static unsigned cm_flash_gpios[] = { GPIO_PF4 };
-
-static struct resource cm_flash_resource[] = {
- {
- .name = "cfi_probe",
- .start = 0x20000000,
- .end = 0x201fffff,
- .flags = IORESOURCE_MEM,
- }, {
- .start = (unsigned long)cm_flash_gpios,
- .end = ARRAY_SIZE(cm_flash_gpios),
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device cm_flash_device = {
- .name = "gpio-addr-flash",
- .id = 0,
- .dev = {
- .platform_data = &cm_flash_data,
- },
- .num_resources = ARRAY_SIZE(cm_flash_resource),
- .resource = cm_flash_resource,
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
-static struct resource bfin_uart_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- }, {
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device bfin_uart_device = {
- .name = "bfin-uart",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_uart_resources),
- .resource = bfin_uart_resources,
-};
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
-static struct resource bfin_sir0_resources[] = {
- {
- .start = 0xFFC00400,
- .end = 0xFFC004FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART0_RX,
- .end = IRQ_UART0_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART0_RX,
- .end = CH_UART0_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-static struct platform_device bfin_sir0_device = {
- .name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir0_resources),
- .resource = bfin_sir0_resources,
-};
-#endif
-#ifdef CONFIG_BFIN_SIR1
-static struct resource bfin_sir1_resources[] = {
- {
- .start = 0xFFC02000,
- .end = 0xFFC020FF,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IRQ_UART1_RX,
- .end = IRQ_UART1_RX+1,
- .flags = IORESOURCE_IRQ,
- },
- {
- .start = CH_UART1_RX,
- .end = CH_UART1_RX+1,
- .flags = IORESOURCE_DMA,
- },
-};
-static struct platform_device bfin_sir1_device = {
- .name = "bfin_sir",
- .id = 1,
- .num_resources = ARRAY_SIZE(bfin_sir1_resources),
- .resource = bfin_sir1_resources,
-};
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
-static struct resource bfin_twi0_resource[] = {
- [0] = {
- .start = TWI0_REGBASE,
- .end = TWI0_REGBASE,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = IRQ_TWI,
- .end = IRQ_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device i2c_bfin_twi_device = {
- .name = "i2c-bfin-twi",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_twi0_resource),
- .resource = bfin_twi0_resource,
-};
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
-static struct platform_device bfin_sport0_uart_device = {
- .name = "bfin-sport-uart",
- .id = 0,
-};
-
-static struct platform_device bfin_sport1_uart_device = {
- .name = "bfin-sport-uart",
- .id = 1,
-};
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
-static struct platform_device bfin_mii_bus = {
- .name = "bfin_mii_bus",
-};
-
-static struct platform_device bfin_mac_device = {
- .name = "bfin_mac",
- .dev.platform_data = &bfin_mii_bus,
-};
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
-#define PATA_INT IRQ_PF14
-
-static struct pata_platform_info bfin_pata_platform_data = {
- .ioport_shift = 2,
- .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
-};
-
-static struct resource bfin_pata_resources[] = {
- {
- .start = 0x2030C000,
- .end = 0x2030C01F,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = 0x2030D018,
- .end = 0x2030D01B,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = PATA_INT,
- .end = PATA_INT,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device bfin_pata_device = {
- .name = "pata_platform",
- .id = -1,
- .num_resources = ARRAY_SIZE(bfin_pata_resources),
- .resource = bfin_pata_resources,
- .dev = {
- .platform_data = &bfin_pata_platform_data,
- }
-};
-#endif
-
-static const unsigned int cclk_vlev_datasheet[] =
-{
- VRPAIR(VLEV_085, 250000000),
- VRPAIR(VLEV_090, 376000000),
- VRPAIR(VLEV_095, 426000000),
- VRPAIR(VLEV_100, 426000000),
- VRPAIR(VLEV_105, 476000000),
- VRPAIR(VLEV_110, 476000000),
- VRPAIR(VLEV_115, 476000000),
- VRPAIR(VLEV_120, 500000000),
- VRPAIR(VLEV_125, 533000000),
- VRPAIR(VLEV_130, 600000000),
-};
-
-static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
- .tuple_tab = cclk_vlev_datasheet,
- .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
- .vr_settling_time = 25 /* us */,
-};
-
-static struct platform_device bfin_dpmc = {
- .name = "bfin dpmc",
- .dev = {
- .platform_data = &bfin_dmpc_vreg_data,
- },
-};
-
-static struct platform_device *cm_bf537_devices[] __initdata = {
-
- &bfin_dpmc,
-
-#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
- &hitachi_fb_device,
-#endif
-
-#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
- &rtc_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
- &bfin_uart_device,
-#endif
-
-#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-#ifdef CONFIG_BFIN_SIR0
- &bfin_sir0_device,
-#endif
-#ifdef CONFIG_BFIN_SIR1
- &bfin_sir1_device,
-#endif
-#endif
-
-#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
- &i2c_bfin_twi_device,
-#endif
-
-#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
- &bfin_sport0_uart_device,
- &bfin_sport1_uart_device,
-#endif
-
-#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
- &isp1362_hcd_device,
-#endif
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
- &smc91x_device,
-#endif
-
-#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
- &bfin_mii_bus,
- &bfin_mac_device,
-#endif
-
-#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
- &net2272_bfin_device,
-#endif
-
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- &bfin_spi0_device,
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
- &bfin_pata_device,
-#endif
-
-#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
- &cm_flash_device,
-#endif
-
- &bfin_gpios_device,
-};
-
-static int __init cm_bf537_init(void)
-{
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- platform_add_devices(cm_bf537_devices, ARRAY_SIZE(cm_bf537_devices));
-#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
- spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
-#endif
-
-#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
- irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
-#endif
- return 0;
-}
-
-arch_initcall(cm_bf537_init);
-
-void bfin_get_ether_addr(char *addr)
-{
- random_ether_addr(addr);
- printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
-}
-EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537e.c b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
new file mode 100644
index 0000000..87acb7d
--- /dev/null
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537e.c
@@ -0,0 +1,727 @@
+/*
+ * File: arch/blackfin/mach-bf537/boards/cm_bf537.c
+ * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author: Aidan Williams <aidan@...ta.com.au>
+ *
+ * Created: 2005
+ * Description: Board description file
+ *
+ * Modified:
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <linux/ata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM BF537E";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader(spi)",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel(spi)",
+ .size = 0xe0000,
+ .offset = 0x20000
+ }, {
+ .name = "file system(spi)",
+ .size = 0x700000,
+ .offset = 0x00100000,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 1, /* use dma transfer with this chip*/
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+ {
+ .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+ {
+ .modalias = "mmc_spi",
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &mmc_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+static struct platform_device hitachi_fb_device = {
+ .name = "hitachi-tx09",
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91x_resources[] = {
+ {
+ .start = 0x20200300,
+ .end = 0x20200300 + 16,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PF14,
+ .end = IRQ_PF14,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+ {
+ .start = 0x20308000,
+ .end = 0x20308000,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = 0x20308004,
+ .end = 0x20308004,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PG15,
+ .end = IRQ_PG15,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+ .sel15Kres = 1,
+ .clknotstop = 0,
+ .oc_enable = 0,
+ .int_act_high = 0,
+ .int_edge_triggered = 0,
+ .remote_wakeup_connected = 0,
+ .no_power_switching = 1,
+ .power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+ .name = "isp1362-hcd",
+ .id = 0,
+ .dev = {
+ .platform_data = &isp1362_priv,
+ },
+ .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+ .resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+ {
+ .start = 0x20300000,
+ .end = 0x20300000 + 0x100,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PG13,
+ .end = IRQ_PG13,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device net2272_bfin_device = {
+ .name = "net2272",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(net2272_bfin_resources),
+ .resource = net2272_bfin_resources,
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+ .start = 0,
+ .end = MAX_BLACKFIN_GPIOS - 1,
+ .flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+ .name = "simple-gpio",
+ .id = -1,
+ .num_resources = 1,
+ .resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x100000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data cm_flash_data = {
+ .width = 2,
+ .parts = cm_partitions,
+ .nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PF4 };
+
+static struct resource cm_flash_resource[] = {
+ {
+ .name = "cfi_probe",
+ .start = 0x20000000,
+ .end = 0x201fffff,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = (unsigned long)cm_flash_gpios,
+ .end = ARRAY_SIZE(cm_flash_gpios),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device cm_flash_device = {
+ .name = "gpio-addr-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &cm_flash_data,
+ },
+ .num_resources = ARRAY_SIZE(cm_flash_resource),
+ .resource = cm_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+static struct resource bfin_uart0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART0_ERROR,
+ .end = IRQ_UART0_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_TX,
+ .end = CH_UART0_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+ {
+ /*
+ * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+ */
+ .start = -1,
+ .end = -1,
+ .flags = IORESOURCE_IO,
+ },
+ {
+ /*
+ * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+ */
+ .start = -1,
+ .end = -1,
+ .flags = IORESOURCE_IO,
+ },
+#endif
+};
+
+static struct platform_device bfin_uart0_device = {
+ .name = "bfin-uart",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_uart0_resources),
+ .resource = bfin_uart0_resources,
+};
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+static struct resource bfin_uart1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = IRQ_UART1_ERROR,
+ .end = IRQ_UART1_ERROR,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_TX,
+ .end = CH_UART1_TX,
+ .flags = IORESOURCE_DMA,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX,
+ .flags = IORESOURCE_DMA,
+ },
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+ {
+ /*
+ * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+ */
+ .start = -1,
+ .end = -1,
+ .flags = IORESOURCE_IO,
+ },
+ {
+ /*
+ * Refer to arch/blackfin/mach-xxx/include/mach/gpio.h for the GPIO map.
+ */
+ .start = -1,
+ .end = -1,
+ .flags = IORESOURCE_IO,
+ },
+#endif
+};
+
+static struct platform_device bfin_uart1_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart1_resources),
+ .resource = bfin_uart1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+ .name = "bfin_mac",
+ .dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT IRQ_PF14
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 2,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x2030C000,
+ .end = 0x2030C01F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2030D018,
+ .end = 0x2030D01B,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+ VRPAIR(VLEV_085, 250000000),
+ VRPAIR(VLEV_090, 376000000),
+ VRPAIR(VLEV_095, 426000000),
+ VRPAIR(VLEV_100, 426000000),
+ VRPAIR(VLEV_105, 476000000),
+ VRPAIR(VLEV_110, 476000000),
+ VRPAIR(VLEV_115, 476000000),
+ VRPAIR(VLEV_120, 500000000),
+ VRPAIR(VLEV_125, 533000000),
+ VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
+static struct platform_device *cm_bf537e_devices[] __initdata = {
+
+ &bfin_dpmc,
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+ &hitachi_fb_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ &bfin_uart0_device,
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ &bfin_uart1_device,
+#endif
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+ &bfin_sport0_uart_device,
+ &bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+ &isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
+ &bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+ &net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+ &cm_flash_device,
+#endif
+
+ &bfin_gpios_device,
+};
+
+static int __init cm_bf537e_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ platform_add_devices(cm_bf537e_devices, ARRAY_SIZE(cm_bf537e_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+ return 0;
+}
+
+arch_initcall(cm_bf537e_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+ random_ether_addr(addr);
+ printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
diff --git a/arch/blackfin/mach-bf537/boards/cm_bf537u.c b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
new file mode 100644
index 0000000..8219dc3
--- /dev/null
+++ b/arch/blackfin/mach-bf537/boards/cm_bf537u.c
@@ -0,0 +1,633 @@
+/*
+ * File: arch/blackfin/mach-bf537/boards/cm_bf537u.c
+ * Based on: arch/blackfin/mach-bf533/boards/ezkit.c
+ * Author: Aidan Williams <aidan@...ta.com.au>
+ *
+ * Created: 2005
+ * Description: Board description file
+ *
+ * Modified:
+ * Copyright 2005 National ICT Australia (NICTA)
+ * Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/device.h>
+#include <linux/etherdevice.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+#include <linux/usb/isp1362.h>
+#endif
+#include <linux/ata_platform.h>
+#include <linux/irq.h>
+#include <asm/dma.h>
+#include <asm/bfin5xx_spi.h>
+#include <asm/portmux.h>
+#include <asm/dpmc.h>
+#include <linux/spi/mmc_spi.h>
+
+/*
+ * Name the Board for the /proc/cpuinfo
+ */
+const char bfin_board_name[] = "Bluetechnix CM BF537U";
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+/* all SPI peripherals info goes here */
+
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+static struct mtd_partition bfin_spi_flash_partitions[] = {
+ {
+ .name = "bootloader(spi)",
+ .size = 0x00020000,
+ .offset = 0,
+ .mask_flags = MTD_CAP_ROM
+ }, {
+ .name = "linux kernel(spi)",
+ .size = 0xe0000,
+ .offset = 0x20000
+ }, {
+ .name = "file system(spi)",
+ .size = 0x700000,
+ .offset = 0x00100000,
+ }
+};
+
+static struct flash_platform_data bfin_spi_flash_data = {
+ .name = "m25p80",
+ .parts = bfin_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
+ .type = "m25p64",
+};
+
+/* SPI flash chip (m25p64) */
+static struct bfin5xx_spi_chip spi_flash_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+/* SPI ADC chip */
+static struct bfin5xx_spi_chip spi_adc_chip_info = {
+ .enable_dma = 1, /* use dma transfer with this chip*/
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 16,
+};
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+static struct bfin5xx_spi_chip mmc_spi_chip_info = {
+ .enable_dma = 0,
+ .bits_per_word = 8,
+};
+#endif
+
+static struct spi_board_info bfin_spi_board_info[] __initdata = {
+#if defined(CONFIG_MTD_M25P80) || defined(CONFIG_MTD_M25P80_MODULE)
+ {
+ /* the modalias must be the same as spi device driver name */
+ .modalias = "m25p80", /* Name of spi_driver for this device */
+ .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
+ .platform_data = &bfin_spi_flash_data,
+ .controller_data = &spi_flash_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+
+#if defined(CONFIG_BFIN_SPI_ADC) || defined(CONFIG_BFIN_SPI_ADC_MODULE)
+ {
+ .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
+ .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0, /* Framework bus number */
+ .chip_select = 1, /* Framework chip select. */
+ .platform_data = NULL, /* No spi_driver specific config */
+ .controller_data = &spi_adc_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_SND_BLACKFIN_AD1836) || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
+ {
+ .modalias = "ad1836",
+ .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
+ .controller_data = &ad1836_spi_chip_info,
+ },
+#endif
+
+#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
+ {
+ .modalias = "mmc_spi",
+ .max_speed_hz = 20000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 1,
+ .controller_data = &mmc_spi_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
+};
+
+/* SPI (0) */
+static struct resource bfin_spi0_resource[] = {
+ [0] = {
+ .start = SPI0_REGBASE,
+ .end = SPI0_REGBASE + 0xFF,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = CH_SPI,
+ .end = CH_SPI,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI,
+ .end = IRQ_SPI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+/* SPI controller data */
+static struct bfin5xx_spi_master bfin_spi0_info = {
+ .num_chipselect = 8,
+ .enable_dma = 1, /* master has the ability to do dma transfer */
+ .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
+};
+
+static struct platform_device bfin_spi0_device = {
+ .name = "bfin-spi",
+ .id = 0, /* Bus number */
+ .num_resources = ARRAY_SIZE(bfin_spi0_resource),
+ .resource = bfin_spi0_resource,
+ .dev = {
+ .platform_data = &bfin_spi0_info, /* Passed to driver */
+ },
+};
+#endif /* spi master and devices */
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+static struct platform_device rtc_device = {
+ .name = "rtc-bfin",
+ .id = -1,
+};
+#endif
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+static struct platform_device hitachi_fb_device = {
+ .name = "hitachi-tx09",
+};
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+#include <linux/smc91x.h>
+
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
+static struct resource smc91x_resources[] = {
+ {
+ .start = 0x20200300,
+ .end = 0x20200300 + 16,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PF14,
+ .end = IRQ_PF14,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device smc91x_device = {
+ .name = "smc91x",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(smc91x_resources),
+ .resource = smc91x_resources,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
+};
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+static struct resource isp1362_hcd_resources[] = {
+ {
+ .start = 0x20308000,
+ .end = 0x20308000,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = 0x20308004,
+ .end = 0x20308004,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PG15,
+ .end = IRQ_PG15,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct isp1362_platform_data isp1362_priv = {
+ .sel15Kres = 1,
+ .clknotstop = 0,
+ .oc_enable = 0,
+ .int_act_high = 0,
+ .int_edge_triggered = 0,
+ .remote_wakeup_connected = 0,
+ .no_power_switching = 1,
+ .power_switching_mode = 0,
+};
+
+static struct platform_device isp1362_hcd_device = {
+ .name = "isp1362-hcd",
+ .id = 0,
+ .dev = {
+ .platform_data = &isp1362_priv,
+ },
+ .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
+ .resource = isp1362_hcd_resources,
+};
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+static struct resource net2272_bfin_resources[] = {
+ {
+ .start = 0x20200000,
+ .end = 0x20200000 + 0x100,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = IRQ_PH14,
+ .end = IRQ_PH14,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+ },
+};
+
+static struct platform_device net2272_bfin_device = {
+ .name = "net2272",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(net2272_bfin_resources),
+ .resource = net2272_bfin_resources,
+};
+#endif
+
+static struct resource bfin_gpios_resources = {
+ .start = 0,
+ .end = MAX_BLACKFIN_GPIOS - 1,
+ .flags = IORESOURCE_IRQ,
+};
+
+static struct platform_device bfin_gpios_device = {
+ .name = "simple-gpio",
+ .id = -1,
+ .num_resources = 1,
+ .resource = &bfin_gpios_resources,
+};
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+static struct mtd_partition cm_partitions[] = {
+ {
+ .name = "bootloader(nor)",
+ .size = 0x40000,
+ .offset = 0,
+ }, {
+ .name = "linux kernel(nor)",
+ .size = 0x100000,
+ .offset = MTDPART_OFS_APPEND,
+ }, {
+ .name = "file system(nor)",
+ .size = MTDPART_SIZ_FULL,
+ .offset = MTDPART_OFS_APPEND,
+ }
+};
+
+static struct physmap_flash_data cm_flash_data = {
+ .width = 2,
+ .parts = cm_partitions,
+ .nr_parts = ARRAY_SIZE(cm_partitions),
+};
+
+static unsigned cm_flash_gpios[] = { GPIO_PH0 };
+
+static struct resource cm_flash_resource[] = {
+ {
+ .name = "cfi_probe",
+ .start = 0x20000000,
+ .end = 0x201fffff,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = (unsigned long)cm_flash_gpios,
+ .end = ARRAY_SIZE(cm_flash_gpios),
+ .flags = IORESOURCE_IRQ,
+ }
+};
+
+static struct platform_device cm_flash_device = {
+ .name = "gpio-addr-flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &cm_flash_data,
+ },
+ .num_resources = ARRAY_SIZE(cm_flash_resource),
+ .resource = cm_flash_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+static struct resource bfin_uart_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ }, {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+static struct platform_device bfin_uart_device = {
+ .name = "bfin-uart",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_uart_resources),
+ .resource = bfin_uart_resources,
+};
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
+ {
+ .start = 0xFFC00400,
+ .end = 0xFFC004FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
+#endif
+#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
+ {
+ .start = 0xFFC02000,
+ .end = 0xFFC020FF,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+static struct resource bfin_twi0_resource[] = {
+ [0] = {
+ .start = TWI0_REGBASE,
+ .end = TWI0_REGBASE,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_TWI,
+ .end = IRQ_TWI,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device i2c_bfin_twi_device = {
+ .name = "i2c-bfin-twi",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_twi0_resource),
+ .resource = bfin_twi0_resource,
+};
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+static struct platform_device bfin_sport0_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 0,
+};
+
+static struct platform_device bfin_sport1_uart_device = {
+ .name = "bfin-sport-uart",
+ .id = 1,
+};
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+static struct platform_device bfin_mii_bus = {
+ .name = "bfin_mii_bus",
+};
+
+static struct platform_device bfin_mac_device = {
+ .name = "bfin_mac",
+ .dev.platform_data = &bfin_mii_bus,
+};
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+#define PATA_INT IRQ_PF14
+
+static struct pata_platform_info bfin_pata_platform_data = {
+ .ioport_shift = 2,
+ .irq_type = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
+};
+
+static struct resource bfin_pata_resources[] = {
+ {
+ .start = 0x2030C000,
+ .end = 0x2030C01F,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = 0x2030D018,
+ .end = 0x2030D01B,
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = PATA_INT,
+ .end = PATA_INT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_pata_device = {
+ .name = "pata_platform",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_pata_resources),
+ .resource = bfin_pata_resources,
+ .dev = {
+ .platform_data = &bfin_pata_platform_data,
+ }
+};
+#endif
+
+static const unsigned int cclk_vlev_datasheet[] =
+{
+ VRPAIR(VLEV_085, 250000000),
+ VRPAIR(VLEV_090, 376000000),
+ VRPAIR(VLEV_095, 426000000),
+ VRPAIR(VLEV_100, 426000000),
+ VRPAIR(VLEV_105, 476000000),
+ VRPAIR(VLEV_110, 476000000),
+ VRPAIR(VLEV_115, 476000000),
+ VRPAIR(VLEV_120, 500000000),
+ VRPAIR(VLEV_125, 533000000),
+ VRPAIR(VLEV_130, 600000000),
+};
+
+static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
+ .tuple_tab = cclk_vlev_datasheet,
+ .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
+ .vr_settling_time = 25 /* us */,
+};
+
+static struct platform_device bfin_dpmc = {
+ .name = "bfin dpmc",
+ .dev = {
+ .platform_data = &bfin_dmpc_vreg_data,
+ },
+};
+
+static struct platform_device *cm_bf537u_devices[] __initdata = {
+
+ &bfin_dpmc,
+
+#if defined(CONFIG_FB_HITACHI_TX09) || defined(CONFIG_FB_HITACHI_TX09_MODULE)
+ &hitachi_fb_device,
+#endif
+
+#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
+ &rtc_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
+ &bfin_uart_device,
+#endif
+
+#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#endif
+
+#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
+ &i2c_bfin_twi_device,
+#endif
+
+#if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
+ &bfin_sport0_uart_device,
+ &bfin_sport1_uart_device,
+#endif
+
+#if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
+ &isp1362_hcd_device,
+#endif
+
+#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
+ &smc91x_device,
+#endif
+
+#if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
+ &bfin_mii_bus,
+ &bfin_mac_device,
+#endif
+
+#if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
+ &net2272_bfin_device,
+#endif
+
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ &bfin_spi0_device,
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ &bfin_pata_device,
+#endif
+
+#if defined(CONFIG_MTD_GPIO_ADDR) || defined(CONFIG_MTD_GPIO_ADDR_MODULE)
+ &cm_flash_device,
+#endif
+
+ &bfin_gpios_device,
+};
+
+static int __init cm_bf537u_init(void)
+{
+ printk(KERN_INFO "%s(): registering device resources\n", __func__);
+ platform_add_devices(cm_bf537u_devices, ARRAY_SIZE(cm_bf537u_devices));
+#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
+ spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
+#endif
+
+#if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
+ irq_desc[PATA_INT].status |= IRQ_NOAUTOEN;
+#endif
+ return 0;
+}
+
+arch_initcall(cm_bf537u_init);
+
+void bfin_get_ether_addr(char *addr)
+{
+ random_ether_addr(addr);
+ printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__);
+}
+EXPORT_SYMBOL(bfin_get_ether_addr);
--
1.6.4.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists