Message-Id: <1253223426-5938-1-git-send-email-vapier@gentoo.org>
Date:	Thu, 17 Sep 2009 17:37:06 -0400
From:	Mike Frysinger <vapier@...too.org>
To:	linux-fbdev-devel@...ts.sourceforge.net
Cc:	linux-kernel@...r.kernel.org,
	Michael Hennerich <michael.hennerich@...log.com>,
	Bryan Wu <cooloney@...nel.org>
Subject: [PATCH v2] fbdev: bfin-lq035q1-fb: new Blackfin Landscape LCD EZ-Extender driver

From: Michael Hennerich <michael.hennerich@...log.com>

Framebuffer driver for the Landscape LCD EZ-Extender (ADZS-BFLLCD-EZEXT)
http://docs.blackfin.uclinux.org/doku.php?id=hw:cards:landscape_lcd_ez-extender

Signed-off-by: Michael Hennerich <michael.hennerich@...log.com>
Signed-off-by: Bryan Wu <cooloney@...nel.org>
Signed-off-by: Mike Frysinger <vapier@...too.org>
---
v2
	- rename spidev driver to fix section mismatch warnings

 arch/blackfin/include/asm/bfin-lq035q1.h |   28 +
 drivers/video/Kconfig                    |   13 +
 drivers/video/Makefile                   |    1 +
 drivers/video/bfin-lq035q1-fb.c          |  855 ++++++++++++++++++++++++++++++
 4 files changed, 897 insertions(+), 0 deletions(-)
 create mode 100644 arch/blackfin/include/asm/bfin-lq035q1.h
 create mode 100644 drivers/video/bfin-lq035q1-fb.c

diff --git a/arch/blackfin/include/asm/bfin-lq035q1.h b/arch/blackfin/include/asm/bfin-lq035q1.h
new file mode 100644
index 0000000..a87a6b6
--- /dev/null
+++ b/arch/blackfin/include/asm/bfin-lq035q1.h
@@ -0,0 +1,28 @@
+/*
+ * Blackfin LCD Framebuffer driver SHARP LQ035Q1DH02
+ *
+ * Copyright 2008-2009 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef BFIN_LQ035Q1_H
+#define BFIN_LQ035Q1_H
+
+#define LQ035_RL	(0 << 8)	/* Right -> Left Scan */
+#define LQ035_LR	(1 << 8)	/* Left -> Right Scan */
+#define LQ035_TB	(1 << 9)	/* Top -> Botton Scan */
+#define LQ035_BT	(0 << 9)	/* Botton -> Top Scan */
+#define LQ035_BGR	(1 << 11)	/* Use BGR format */
+#define LQ035_RGB	(0 << 11)	/* Use RGB format */
+#define LQ035_NORM	(1 << 13)	/* Reversal */
+#define LQ035_REV	(0 << 13)	/* Reversal */
+
+struct bfin_lq035q1fb_disp_info {
+
+	unsigned	mode;
+	/* GPIOs */
+	int		use_bl;
+	unsigned 	gpio_bl;
+};
+
+#endif /* BFIN_LQ035Q1_H */
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index cef3e1d..bb10916 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -611,6 +611,19 @@ config FB_BFIN_T350MCQB
 	 This display is a QVGA 320x240 24-bit RGB display interfaced by an 8-bit wide PPI
 	 It uses PPI[0..7] PPI_FS1, PPI_FS2 and PPI_CLK.
 
+config FB_BFIN_LQ035Q1
+	tristate "SHARP LQ035Q1DH02 TFT LCD"
+	depends on FB && BLACKFIN
+	select FB_CFB_FILLRECT
+	select FB_CFB_COPYAREA
+	select FB_CFB_IMAGEBLIT
+	select BFIN_GPTIMERS
+	select SPI
+	help
+	  This is the framebuffer device driver for a SHARP LQ035Q1DH02 TFT display found on
+	  the Blackfin Landscape LCD EZ-Extender Card.
+	  This display is a QVGA 320x240 18-bit RGB display interfaced by an 16-bit wide PPI
+	  It uses PPI[0..15] PPI_FS1, PPI_FS2 and PPI_CLK.
 
 config FB_STI
 	tristate "HP STI frame buffer device support"
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index 01a819f..cc7682b 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -134,6 +134,7 @@ obj-$(CONFIG_FB_EFI)              += efifb.o
 obj-$(CONFIG_FB_VGA16)            += vga16fb.o
 obj-$(CONFIG_FB_OF)               += offb.o
 obj-$(CONFIG_FB_BF54X_LQ043)	  += bf54x-lq043fb.o
+obj-$(CONFIG_FB_BFIN_LQ035Q1)     += bfin-lq035q1-fb.o
 obj-$(CONFIG_FB_BFIN_T350MCQB)	  += bfin-t350mcqb-fb.o
 obj-$(CONFIG_FB_MX3)		  += mx3fb.o
 
diff --git a/drivers/video/bfin-lq035q1-fb.c b/drivers/video/bfin-lq035q1-fb.c
new file mode 100644
index 0000000..e766bba
--- /dev/null
+++ b/drivers/video/bfin-lq035q1-fb.c
@@ -0,0 +1,855 @@
+/*
+ * Blackfin LCD Framebuffer driver SHARP LQ035Q1DH02
+ *
+ * Copyright 2008-2009 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#define pr_fmt(fmt) DRIVER_NAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/backlight.h>
+#include <linux/lcd.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/blackfin.h>
+#include <asm/irq.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+#include <asm/gptimers.h>
+
+#include <asm/bfin-lq035q1.h>
+
+#if defined(BF533_FAMILY) || defined(BF538_FAMILY)
+#define TIMER_HSYNC_id			TIMER1_id
+#define TIMER_HSYNCbit			TIMER1bit
+#define TIMER_HSYNC_STATUS_TRUN		TIMER_STATUS_TRUN1
+#define TIMER_HSYNC_STATUS_TIMIL	TIMER_STATUS_TIMIL1
+#define TIMER_HSYNC_STATUS_TOVF		TIMER_STATUS_TOVF1
+
+#define TIMER_VSYNC_id			TIMER2_id
+#define TIMER_VSYNCbit			TIMER2bit
+#define TIMER_VSYNC_STATUS_TRUN		TIMER_STATUS_TRUN2
+#define TIMER_VSYNC_STATUS_TIMIL	TIMER_STATUS_TIMIL2
+#define TIMER_VSYNC_STATUS_TOVF		TIMER_STATUS_TOVF2
+#else
+#define TIMER_HSYNC_id			TIMER0_id
+#define TIMER_HSYNCbit			TIMER0bit
+#define TIMER_HSYNC_STATUS_TRUN		TIMER_STATUS_TRUN0
+#define TIMER_HSYNC_STATUS_TIMIL	TIMER_STATUS_TIMIL0
+#define TIMER_HSYNC_STATUS_TOVF		TIMER_STATUS_TOVF0
+
+#define TIMER_VSYNC_id			TIMER1_id
+#define TIMER_VSYNCbit			TIMER1bit
+#define TIMER_VSYNC_STATUS_TRUN		TIMER_STATUS_TRUN1
+#define TIMER_VSYNC_STATUS_TIMIL	TIMER_STATUS_TIMIL1
+#define TIMER_VSYNC_STATUS_TOVF		TIMER_STATUS_TOVF1
+#endif
+
+#define LCD_X_RES		320	/* Horizontal Resolution */
+#define LCD_Y_RES		240	/* Vertical Resolution */
+#define	DMA_BUS_SIZE		16
+
+#define USE_RGB565_16_BIT_PPI
+
+#ifdef USE_RGB565_16_BIT_PPI
+#define LCD_BPP		16	/* Bit Per Pixel */
+#define CLOCKS_PER_PIX	1
+#define CPLD_PIPELINE_DELAY_COR 0	/* NO CPLB */
+#endif
+
+/* Interface 16/18-bit TFT over an 8-bit wide PPI using a small Programmable Logic Device (CPLD)
+ * http://blackfin.uclinux.org/gf/project/stamp/frs/?action=FrsReleaseBrowse&frs_package_id=165
+ */
+
+#ifdef USE_RGB565_8_BIT_PPI
+#define LCD_BPP		16	/* Bit Per Pixel */
+#define CLOCKS_PER_PIX	2
+#define CPLD_PIPELINE_DELAY_COR 3	/* RGB565 */
+#endif
+
+#ifdef USE_RGB888_8_BIT_PPI
+#define LCD_BPP		24	/* Bit Per Pixel */
+#define CLOCKS_PER_PIX	3
+#define CPLD_PIPELINE_DELAY_COR 5	/* RGB888 */
+#endif
+
+	/*
+	 * HS and VS timing parameters (all in number of PPI clk ticks)
+	 */
+
+#define U_LINE		4				/* Blanking Lines */
+
+#define H_ACTPIX	(LCD_X_RES * CLOCKS_PER_PIX)	/* active horizontal pixel */
+#define H_PERIOD	(336 * CLOCKS_PER_PIX)		/* HS period */
+#define H_PULSE		(2 * CLOCKS_PER_PIX)				/* HS pulse width */
+#define H_START		(7 * CLOCKS_PER_PIX + CPLD_PIPELINE_DELAY_COR)	/* first valid pixel */
+
+#define	V_LINES		(LCD_Y_RES + U_LINE)		/* total vertical lines */
+#define V_PULSE		(2 * CLOCKS_PER_PIX)		/* VS pulse width (1-5 H_PERIODs) */
+#define V_PERIOD	(H_PERIOD * V_LINES)		/* VS period */
+
+#define ACTIVE_VIDEO_MEM_OFFSET		((U_LINE / 2) * LCD_X_RES * (LCD_BPP / 8))
+
+#define BFIN_LCD_NBR_PALETTE_ENTRIES	256
+
+#define PPI_TX_MODE			0x2
+#define PPI_XFER_TYPE_11		0xC
+#define PPI_PORT_CFG_01			0x10
+#define PPI_POLS_1			0x8000
+
+#if (CLOCKS_PER_PIX > 1)
+#define PPI_PMODE (DLEN_8 | PACK_EN)
+#else
+#define PPI_PMODE (DLEN_16)
+#endif
+
+#define LQ035_INDEX			0x74
+#define LQ035_DATA			0x76
+
+#define LQ035_DRIVER_OUTPUT_CTL		0x1
+#define LQ035_SHUT_CTL			0x11
+
+#define LQ035_DRIVER_OUTPUT_MASK	(LQ035_LR | LQ035_TB | LQ035_BGR | LQ035_REV)
+#define LQ035_DRIVER_OUTPUT_DEFAULT	(0x2AEF & ~LQ035_DRIVER_OUTPUT_MASK)
+
+#define LQ035_SHUT			(1 << 0)	/* Shutdown */
+#define LQ035_ON			(0 << 0)	/* Shutdown */
+
+#define DRIVER_NAME "bfin-lq035q1"
+static char driver_name[] = DRIVER_NAME;
+
+struct bfin_lq035q1fb_info {
+	struct fb_info *fb;
+	struct device *dev;
+	struct bfin_lq035q1fb_disp_info *disp_info;
+	unsigned char *fb_buffer;	/* RGB Buffer */
+	dma_addr_t dma_handle;
+	int lq035_mmap;
+	int lq035_open_cnt;
+	int irq;
+	spinlock_t lock;	/* lock */
+	u32 pseudo_pal[16];
+};
+
+static int nocursor;
+module_param(nocursor, int, 0644);
+MODULE_PARM_DESC(nocursor, "cursor enable/disable");
+
+
+static struct {
+	struct spi_device *spidev;
+	unsigned short mode;
+	unsigned short init;
+} spi_control;
+
+static int lq035q1_control(unsigned char reg, unsigned short value)
+{
+	int ret;
+	u8 regs[3] = {LQ035_INDEX, 0, 0};
+	u8 dat[3] = {LQ035_DATA, 0, 0};
+
+	if (spi_control.spidev) {
+		regs[2] = reg;
+		dat[1] = value >> 8;
+		dat[2] = value & 0xFF;
+
+		ret = spi_write(spi_control.spidev, regs, ARRAY_SIZE(regs));
+		ret |= spi_write(spi_control.spidev, dat, ARRAY_SIZE(dat));
+	} else
+		return -ENODEV;
+
+	return ret;
+}
+
+static int __devinit lq035q1_spidev_probe(struct spi_device *spi)
+{
+	int ret;
+	spi_control.spidev = spi;
+
+	ret = lq035q1_control(LQ035_SHUT_CTL, LQ035_ON);
+	ret |= lq035q1_control(LQ035_DRIVER_OUTPUT_CTL, spi_control.mode);
+
+	if (ret)
+		return ret;
+
+	spi_control.init = 1;
+
+	return 0;
+}
+
+static int __devexit lq035q1_spidev_remove(struct spi_device *spi)
+{
+	return lq035q1_control(LQ035_SHUT_CTL, LQ035_SHUT);
+}
+
+#ifdef CONFIG_PM
+static int lq035q1_spidev_suspend(struct spi_device *spi, pm_message_t state)
+{
+	return lq035q1_control(LQ035_SHUT_CTL, LQ035_SHUT);
+}
+
+static int lq035q1_spidev_resume(struct spi_device *spi)
+{
+	int ret = lq035q1_control(LQ035_DRIVER_OUTPUT_CTL, spi_control.mode);
+
+	if (ret)
+		return ret;
+
+	return lq035q1_control(LQ035_SHUT_CTL, LQ035_ON);
+}
+#else
+#define lq035q1_spidev_suspend		NULL
+#define lq035q1_spidev_resume		NULL
+#endif
+
+/* Power down all displays on reboot, poweroff or halt */
+static void lq035q1_spidev_shutdown(struct spi_device *spi)
+{
+	lq035q1_control(LQ035_SHUT_CTL, LQ035_SHUT);
+}
+
+static struct spi_driver spidev_spi_driver = {
+	.driver = {
+		.name =		DRIVER_NAME"-spi",
+		.owner =	THIS_MODULE,
+	},
+	.probe =	lq035q1_spidev_probe,
+	.remove =	__devexit_p(lq035q1_spidev_remove),
+	.shutdown	= lq035q1_spidev_shutdown,
+	.suspend	= lq035q1_spidev_suspend,
+	.resume		= lq035q1_spidev_resume,
+};
+
+static int lq035q1_backlight(struct bfin_lq035q1fb_info *info, unsigned arg)
+{
+	if (info->disp_info->use_bl)
+		gpio_set_value(info->disp_info->gpio_bl, arg);
+
+	return 0;
+}
+
+static void bfin_lq035q1_config_ppi(struct bfin_lq035q1fb_info *fbi)
+{
+	bfin_write_PPI_DELAY(H_START);
+	bfin_write_PPI_COUNT(H_ACTPIX - 1);
+	bfin_write_PPI_FRAME(V_LINES);
+
+	bfin_write_PPI_CONTROL(PPI_TX_MODE |	   /* output mode , PORT_DIR */
+				PPI_XFER_TYPE_11 | /* sync mode XFR_TYPE */
+				PPI_PORT_CFG_01 |  /* two frame sync PORT_CFG */
+				PPI_PMODE |	   /* 8/16 bit data length / PACK_EN? */
+				PPI_POLS_1);	   /* faling edge syncs POLS */
+}
+
+static inline void bfin_lq035q1_disable_ppi(void)
+{
+	bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() & ~PORT_EN);
+}
+
+static inline void bfin_lq035q1_enable_ppi(void)
+{
+	bfin_write_PPI_CONTROL(bfin_read_PPI_CONTROL() | PORT_EN);
+}
+
+static void bfin_lq035q1_start_timers(void)
+{
+	enable_gptimers(TIMER_VSYNCbit | TIMER_HSYNCbit);
+}
+
+static void bfin_lq035q1_stop_timers(void)
+{
+	disable_gptimers(TIMER_HSYNCbit | TIMER_VSYNCbit);
+
+	set_gptimer_status(0, TIMER_HSYNC_STATUS_TRUN | TIMER_VSYNC_STATUS_TRUN |
+				TIMER_HSYNC_STATUS_TIMIL | TIMER_VSYNC_STATUS_TIMIL |
+				 TIMER_HSYNC_STATUS_TOVF | TIMER_VSYNC_STATUS_TOVF);
+
+}
+
+static void bfin_lq035q1_init_timers(void)
+{
+
+	bfin_lq035q1_stop_timers();
+
+	set_gptimer_period(TIMER_HSYNC_id, H_PERIOD);
+	set_gptimer_pwidth(TIMER_HSYNC_id, H_PULSE);
+	set_gptimer_config(TIMER_HSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
+				      TIMER_TIN_SEL | TIMER_CLK_SEL|
+				      TIMER_EMU_RUN);
+
+	set_gptimer_period(TIMER_VSYNC_id, V_PERIOD);
+	set_gptimer_pwidth(TIMER_VSYNC_id, V_PULSE);
+	set_gptimer_config(TIMER_VSYNC_id, TIMER_MODE_PWM | TIMER_PERIOD_CNT |
+				      TIMER_TIN_SEL | TIMER_CLK_SEL |
+				      TIMER_EMU_RUN);
+
+}
+
+static void bfin_lq035q1_config_dma(struct bfin_lq035q1fb_info *fbi)
+{
+
+	set_dma_config(CH_PPI,
+		       set_bfin_dma_config(DIR_READ, DMA_FLOW_AUTO,
+					   INTR_DISABLE, DIMENSION_2D,
+					   DATA_SIZE_16,
+					   DMA_NOSYNC_KEEP_DMA_BUF));
+	set_dma_x_count(CH_PPI, (LCD_X_RES * LCD_BPP) / DMA_BUS_SIZE);
+	set_dma_x_modify(CH_PPI, DMA_BUS_SIZE / 8);
+	set_dma_y_count(CH_PPI, V_LINES);
+
+	set_dma_y_modify(CH_PPI, DMA_BUS_SIZE / 8);
+	set_dma_start_addr(CH_PPI, (unsigned long)fbi->fb_buffer);
+
+}
+
+#if (CLOCKS_PER_PIX == 1)
+static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
+			    P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
+			    P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
+			    P_PPI0_D6, P_PPI0_D7, P_PPI0_D8,
+			    P_PPI0_D9, P_PPI0_D10, P_PPI0_D11,
+			    P_PPI0_D12, P_PPI0_D13, P_PPI0_D14,
+			    P_PPI0_D15, 0};
+#else
+static const u16 ppi0_req_16[] = {P_PPI0_CLK, P_PPI0_FS1, P_PPI0_FS2,
+			    P_PPI0_D0, P_PPI0_D1, P_PPI0_D2,
+			    P_PPI0_D3, P_PPI0_D4, P_PPI0_D5,
+			    P_PPI0_D6, P_PPI0_D7, 0};
+#endif
+
+static int bfin_lq035q1_request_ports(int action)
+{
+	if (action) {
+		/* ANOMALY_05000400 - PPI Does Not Start Properly In Specific Mode:
+		 * Drive PPI_FS3 Low
+		 */
+		if (ANOMALY_05000400) {
+			int ret = gpio_request(P_IDENT(P_PPI0_FS3), "PPI_FS3");
+			if (ret)
+				return ret;
+			gpio_direction_output(P_IDENT(P_PPI0_FS3), 0);
+		}
+
+		if (peripheral_request_list(ppi0_req_16, DRIVER_NAME)) {
+			pr_err("requesting peripherals failed\n");
+			return -EFAULT;
+		}
+	} else {
+		peripheral_free_list(ppi0_req_16);
+		if (ANOMALY_05000400)
+			gpio_free(P_IDENT(P_PPI0_FS3));
+	}
+
+	return 0;
+}
+
+static int bfin_lq035q1_fb_open(struct fb_info *info, int user)
+{
+	struct bfin_lq035q1fb_info *fbi = info->par;
+
+	spin_lock(&fbi->lock);
+	fbi->lq035_open_cnt++;
+
+	if (fbi->lq035_open_cnt <= 1) {
+
+		bfin_lq035q1_disable_ppi();
+		SSYNC();
+
+		bfin_lq035q1_config_dma(fbi);
+		bfin_lq035q1_config_ppi(fbi);
+		bfin_lq035q1_init_timers();
+
+		/* start dma */
+		enable_dma(CH_PPI);
+		bfin_lq035q1_enable_ppi();
+		bfin_lq035q1_start_timers();
+		lq035q1_backlight(fbi, 1);
+	}
+
+	spin_unlock(&fbi->lock);
+
+	return 0;
+}
+
+static int bfin_lq035q1_fb_release(struct fb_info *info, int user)
+{
+	struct bfin_lq035q1fb_info *fbi = info->par;
+
+	spin_lock(&fbi->lock);
+
+	fbi->lq035_open_cnt--;
+	fbi->lq035_mmap = 0;
+
+	if (fbi->lq035_open_cnt <= 0) {
+		lq035q1_backlight(fbi, 0);
+		bfin_lq035q1_disable_ppi();
+		SSYNC();
+		disable_dma(CH_PPI);
+		bfin_lq035q1_stop_timers();
+	}
+
+	spin_unlock(&fbi->lock);
+
+	return 0;
+}
+
+static int bfin_lq035q1_fb_check_var(struct fb_var_screeninfo *var,
+				   struct fb_info *info)
+{
+
+	switch (var->bits_per_pixel) {
+#if (LCD_BPP == 24)
+	case 24:/* TRUECOLOUR, 16m */
+#else
+	case 16:/* DIRECTCOLOUR, 64k */
+#endif
+		var->red.offset = info->var.red.offset;
+		var->green.offset = info->var.green.offset;
+		var->blue.offset = info->var.blue.offset;
+		var->red.length = info->var.red.length;
+		var->green.length = info->var.green.length;
+		var->blue.length = info->var.blue.length;
+		var->transp.offset = 0;
+		var->transp.length = 0;
+		var->transp.msb_right = 0;
+		var->red.msb_right = 0;
+		var->green.msb_right = 0;
+		var->blue.msb_right = 0;
+		break;
+	default:
+		pr_debug("%s: depth not supported: %u BPP\n", __func__,
+			 var->bits_per_pixel);
+		return -EINVAL;
+	}
+
+	if (info->var.xres != var->xres || info->var.yres != var->yres ||
+	    info->var.xres_virtual != var->xres_virtual ||
+	    info->var.yres_virtual != var->yres_virtual) {
+		pr_debug("%s: Resolution not supported: X%u x Y%u \n",
+			 __func__, var->xres, var->yres);
+		return -EINVAL;
+	}
+
+	/*
+	 *  Memory limit
+	 */
+
+	if ((info->fix.line_length * var->yres_virtual) > info->fix.smem_len) {
+		pr_debug("%s: Memory Limit requested yres_virtual = %u\n",
+			 __func__, var->yres_virtual);
+		return -ENOMEM;
+	}
+
+
+	return 0;
+}
+
+static int bfin_lq035q1_fb_mmap(struct fb_info *info, struct vm_area_struct *vma)
+{
+	struct bfin_lq035q1fb_info *fbi = info->par;
+
+	if (fbi->lq035_mmap)
+		return -1;
+
+	spin_lock(&fbi->lock);
+	fbi->lq035_mmap = 1;
+	spin_unlock(&fbi->lock);
+
+	vma->vm_start = (unsigned long)(fbi->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET);
+
+	vma->vm_end = vma->vm_start + info->fix.smem_len;
+	/* For those who don't understand how mmap works, go read
+	 *   Documentation/nommu-mmap.txt.
+	 * For those that do, you will know that the VM_MAYSHARE flag
+	 * must be set in the vma->vm_flags structure on noMMU
+	 *   Other flags can be set, and are documented in
+	 *   include/linux/mm.h
+	 */
+	vma->vm_flags |= VM_MAYSHARE | VM_SHARED;
+
+	return 0;
+}
+
+int bfin_lq035q1_fb_cursor(struct fb_info *info, struct fb_cursor *cursor)
+{
+	if (nocursor)
+		return 0;
+	else
+		return -EINVAL;	/* just to force soft_cursor() call */
+}
+
+static int bfin_lq035q1_fb_setcolreg(u_int regno, u_int red, u_int green,
+				   u_int blue, u_int transp,
+				   struct fb_info *info)
+{
+	if (regno >= BFIN_LCD_NBR_PALETTE_ENTRIES)
+		return -EINVAL;
+
+	if (info->var.grayscale) {
+		/* grayscale = 0.30*R + 0.59*G + 0.11*B */
+		red = green = blue = (red * 77 + green * 151 + blue * 28) >> 8;
+	}
+
+	if (info->fix.visual == FB_VISUAL_TRUECOLOR) {
+
+		u32 value;
+		/* Place color in the pseudopalette */
+		if (regno > 16)
+			return -EINVAL;
+
+		red >>= (16 - info->var.red.length);
+		green >>= (16 - info->var.green.length);
+		blue >>= (16 - info->var.blue.length);
+
+		value = (red << info->var.red.offset) |
+		    (green << info->var.green.offset) |
+		    (blue << info->var.blue.offset);
+		value &= 0xFFFFFF;
+
+		((u32 *) (info->pseudo_palette))[regno] = value;
+
+	}
+
+	return 0;
+}
+
+static struct fb_ops bfin_lq035q1_fb_ops = {
+	.owner = THIS_MODULE,
+	.fb_open = bfin_lq035q1_fb_open,
+	.fb_release = bfin_lq035q1_fb_release,
+	.fb_check_var = bfin_lq035q1_fb_check_var,
+	.fb_fillrect = cfb_fillrect,
+	.fb_copyarea = cfb_copyarea,
+	.fb_imageblit = cfb_imageblit,
+	.fb_mmap = bfin_lq035q1_fb_mmap,
+	.fb_cursor = bfin_lq035q1_fb_cursor,
+	.fb_setcolreg = bfin_lq035q1_fb_setcolreg,
+};
+
+static irqreturn_t bfin_lq035q1_irq_error(int irq, void *dev_id)
+{
+	/*struct bfin_lq035q1fb_info *info = (struct bfin_lq035q1fb_info *)dev_id;*/
+
+	u16 status = bfin_read_PPI_STATUS();
+	bfin_write_PPI_STATUS(-1);
+
+	if (status) {
+		bfin_lq035q1_disable_ppi();
+		disable_dma(CH_PPI);
+
+		/* start dma */
+		enable_dma(CH_PPI);
+		bfin_lq035q1_enable_ppi();
+		bfin_write_PPI_STATUS(-1);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int __devinit bfin_lq035q1_probe(struct platform_device *pdev)
+{
+	struct bfin_lq035q1fb_info *info;
+	struct fb_info *fbinfo;
+	int ret;
+
+	ret = request_dma(CH_PPI, "CH_PPI");
+	if (ret < 0) {
+		pr_err("couldn't request CH_PPI DMA\n");
+		goto out1;
+	}
+
+	fbinfo =
+	    framebuffer_alloc(sizeof(struct bfin_lq035q1fb_info), &pdev->dev);
+	if (!fbinfo) {
+		ret = -ENOMEM;
+		goto out2;
+	}
+
+	info = fbinfo->par;
+	info->fb = fbinfo;
+	info->dev = &pdev->dev;
+
+	info->disp_info = pdev->dev.platform_data;
+
+	spi_control.mode = (info->disp_info->mode &
+		LQ035_DRIVER_OUTPUT_MASK) | LQ035_DRIVER_OUTPUT_DEFAULT;
+
+	platform_set_drvdata(pdev, fbinfo);
+
+	strcpy(fbinfo->fix.id, driver_name);
+
+	fbinfo->fix.type = FB_TYPE_PACKED_PIXELS;
+	fbinfo->fix.type_aux = 0;
+	fbinfo->fix.xpanstep = 0;
+	fbinfo->fix.ypanstep = 0;
+	fbinfo->fix.ywrapstep = 0;
+	fbinfo->fix.accel = FB_ACCEL_NONE;
+	fbinfo->fix.visual = FB_VISUAL_TRUECOLOR;
+
+	fbinfo->var.nonstd = 0;
+	fbinfo->var.activate = FB_ACTIVATE_NOW;
+	fbinfo->var.height = -1;
+	fbinfo->var.width = -1;
+	fbinfo->var.accel_flags = 0;
+	fbinfo->var.vmode = FB_VMODE_NONINTERLACED;
+
+	fbinfo->var.xres = LCD_X_RES;
+	fbinfo->var.xres_virtual = LCD_X_RES;
+	fbinfo->var.yres = LCD_Y_RES;
+	fbinfo->var.yres_virtual = LCD_Y_RES;
+	fbinfo->var.bits_per_pixel = LCD_BPP;
+
+	if (info->disp_info->mode & LQ035_BGR) {
+#if (LCD_BPP == 24)
+		fbinfo->var.red.offset = 0;
+		fbinfo->var.green.offset = 8;
+		fbinfo->var.blue.offset = 16;
+#else
+		fbinfo->var.red.offset = 0;
+		fbinfo->var.green.offset = 5;
+		fbinfo->var.blue.offset = 11;
+#endif
+	} else {
+#if (LCD_BPP == 24)
+		fbinfo->var.red.offset = 16;
+		fbinfo->var.green.offset = 8;
+		fbinfo->var.blue.offset = 0;
+#else
+		fbinfo->var.red.offset = 11;
+		fbinfo->var.green.offset = 5;
+		fbinfo->var.blue.offset = 0;
+#endif
+	}
+
+	fbinfo->var.transp.offset = 0;
+
+#if (LCD_BPP == 24)
+	fbinfo->var.red.length = 8;
+	fbinfo->var.green.length = 8;
+	fbinfo->var.blue.length = 8;
+#else
+	fbinfo->var.red.length = 5;
+	fbinfo->var.green.length = 6;
+	fbinfo->var.blue.length = 5;
+#endif
+
+	fbinfo->var.transp.length = 0;
+
+	fbinfo->fix.smem_len = LCD_X_RES * LCD_Y_RES * LCD_BPP / 8
+				+ ACTIVE_VIDEO_MEM_OFFSET;
+
+	fbinfo->fix.line_length = fbinfo->var.xres_virtual *
+	    fbinfo->var.bits_per_pixel / 8;
+
+
+	fbinfo->fbops = &bfin_lq035q1_fb_ops;
+	fbinfo->flags = FBINFO_FLAG_DEFAULT;
+
+	info->fb_buffer =
+	    dma_alloc_coherent(NULL, fbinfo->fix.smem_len, &info->dma_handle,
+			       GFP_KERNEL);
+
+	if (NULL == info->fb_buffer) {
+		pr_err("couldn't allocate dma buffer\n");
+		ret = -ENOMEM;
+		goto out3;
+	}
+
+	fbinfo->screen_base = (void *)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
+	fbinfo->fix.smem_start = (int)info->fb_buffer + ACTIVE_VIDEO_MEM_OFFSET;
+
+	fbinfo->fbops = &bfin_lq035q1_fb_ops;
+
+	fbinfo->pseudo_palette = &info->pseudo_pal;
+
+	ret = fb_alloc_cmap(&fbinfo->cmap, BFIN_LCD_NBR_PALETTE_ENTRIES, 0);
+	if (ret < 0) {
+		pr_err("failed to allocate colormap (%d entries)\n",
+		       BFIN_LCD_NBR_PALETTE_ENTRIES);
+		goto out4;
+	}
+
+	ret = bfin_lq035q1_request_ports(1);
+	if (ret) {
+		pr_err("couldn't request gpio port\n");
+		goto out6;
+	}
+
+	info->irq = platform_get_irq(pdev, 0);
+	if (info->irq < 0) {
+		ret = -EINVAL;
+		goto out7;
+	}
+
+	ret = request_irq(info->irq, bfin_lq035q1_irq_error, IRQF_DISABLED,
+			"PPI ERROR", info);
+	if (ret < 0) {
+		pr_err("unable to request PPI ERROR IRQ\n");
+		goto out7;
+	}
+
+	ret = spi_register_driver(&spidev_spi_driver);
+	if (ret < 0) {
+		pr_err("couldn't register SPI Interface\n");
+		goto out8;
+	}
+
+	if (info->disp_info->use_bl) {
+		ret = gpio_request(info->disp_info->gpio_bl, "LQ035 Backlight");
+
+		if (ret) {
+			pr_err("failed to request GPIO %d\n",
+				info->disp_info->gpio_bl);
+			goto out9;
+		}
+		gpio_direction_output(info->disp_info->gpio_bl, 0);
+	}
+
+	ret = register_framebuffer(fbinfo);
+	if (ret < 0) {
+		pr_err("unable to register framebuffer\n");
+		goto out10;
+	}
+
+	pr_info("%dx%d %d-bit RGB FrameBuffer initialized\n",
+		LCD_X_RES, LCD_Y_RES, LCD_BPP);
+
+	return 0;
+
+out10:
+	if (info->disp_info->use_bl)
+		gpio_free(info->disp_info->gpio_bl);
+out9:
+	spi_unregister_driver(&spidev_spi_driver);
+out8:
+	free_irq(info->irq, info);
+out7:
+	bfin_lq035q1_request_ports(0);
+out6:
+	fb_dealloc_cmap(&fbinfo->cmap);
+out4:
+	dma_free_coherent(NULL, fbinfo->fix.smem_len, info->fb_buffer,
+			  info->dma_handle);
+out3:
+	framebuffer_release(fbinfo);
+out2:
+	free_dma(CH_PPI);
+out1:
+	platform_set_drvdata(pdev, NULL);
+
+	return ret;
+}
+
+static int __devexit bfin_lq035q1_remove(struct platform_device *pdev)
+{
+	struct fb_info *fbinfo = platform_get_drvdata(pdev);
+	struct bfin_lq035q1fb_info *info = fbinfo->par;
+
+	if (info->disp_info->use_bl)
+		gpio_free(info->disp_info->gpio_bl);
+
+	spi_unregister_driver(&spidev_spi_driver);
+
+	unregister_framebuffer(fbinfo);
+
+	free_dma(CH_PPI);
+	free_irq(info->irq, info);
+
+	if (info->fb_buffer != NULL)
+		dma_free_coherent(NULL, fbinfo->fix.smem_len, info->fb_buffer,
+				  info->dma_handle);
+
+	fb_dealloc_cmap(&fbinfo->cmap);
+
+	bfin_lq035q1_request_ports(0);
+
+	platform_set_drvdata(pdev, NULL);
+	framebuffer_release(fbinfo);
+
+	pr_info("unregistered LCD driver\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int bfin_lq035q1_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct fb_info *fbinfo = platform_get_drvdata(pdev);
+	struct bfin_lq035q1fb_info *info = fbinfo->par;
+
+	if (info->lq035_open_cnt) {
+		lq035q1_backlight(info, 0);
+		bfin_lq035q1_disable_ppi();
+		SSYNC();
+		disable_dma(CH_PPI);
+		bfin_lq035q1_stop_timers();
+		bfin_write_PPI_STATUS(-1);
+	}
+
+	return 0;
+}
+
+static int bfin_lq035q1_resume(struct platform_device *pdev)
+{
+	struct fb_info *fbinfo = platform_get_drvdata(pdev);
+	struct bfin_lq035q1fb_info *info = fbinfo->par;
+
+	if (info->lq035_open_cnt) {
+		bfin_lq035q1_disable_ppi();
+		SSYNC();
+
+		bfin_lq035q1_config_dma(info);
+		bfin_lq035q1_config_ppi(info);
+		bfin_lq035q1_init_timers();
+
+		/* start dma */
+		enable_dma(CH_PPI);
+		bfin_lq035q1_enable_ppi();
+		bfin_lq035q1_start_timers();
+		lq035q1_backlight(info, 1);
+	}
+
+	return 0;
+}
+#else
+#define bfin_lq035q1_suspend	NULL
+#define bfin_lq035q1_resume	NULL
+#endif
+
+static struct platform_driver bfin_lq035q1_driver = {
+	.probe = bfin_lq035q1_probe,
+	.remove = __devexit_p(bfin_lq035q1_remove),
+	.suspend = bfin_lq035q1_suspend,
+	.resume = bfin_lq035q1_resume,
+	.driver = {
+		.name = DRIVER_NAME,
+		.owner = THIS_MODULE,
+	},
+};
+
+static int __init bfin_lq035q1_driver_init(void)
+{
+	return platform_driver_register(&bfin_lq035q1_driver);
+}
+module_init(bfin_lq035q1_driver_init);
+
+static void __exit bfin_lq035q1_driver_cleanup(void)
+{
+	platform_driver_unregister(&bfin_lq035q1_driver);
+}
+module_exit(bfin_lq035q1_driver_cleanup);
+
+MODULE_DESCRIPTION("Blackfin TFT LCD Driver");
+MODULE_LICENSE("GPL");
-- 
1.6.5.rc1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists