| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <201001101437.36458.rjw@sisk.pl>
Date: Sun, 10 Jan 2010 14:37:36 +0100
From: "Rafael J. Wysocki" <rjw@...k.pl>
To: Jesse Barnes <jbarnes@...tuousgeek.org>
Cc: "Moore, Robert" <robert.moore@...el.com>,
Matthew Garrett <mjg@...hat.com>, Len Brown <lenb@...nel.org>,
LKML <linux-kernel@...r.kernel.org>,
pm list <linux-pm@...ts.linux-foundation.org>,
Linux PCI <linux-pci@...r.kernel.org>,
Alan Stern <stern@...land.harvard.edu>,
Oliver Neukum <oliver@...kum.org>,
Bjorn Helgaas <bjorn.helgaas@...com>,
Shaohua Li <shaohua.li@...el.com>
Subject: [PATCH 3/9] PCI PM: Make it possible to force using INTx for PCIe PME signaling
From: Rafael J. Wysocki <rjw@...k.pl>
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling. In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port. [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.] However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.
For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.
Signed-off-by: Rafael J. Wysocki <rjw@...k.pl>
---
Documentation/kernel-parameters.txt | 2 ++
drivers/pci/pcie/pme/pcie_pme.c | 14 +++++++++++++-
drivers/pci/pcie/portdrv.h | 17 +++++++++++++++++
drivers/pci/pcie/portdrv_core.c | 12 ++++++++++--
drivers/pci/pcie/portdrv_pci.c | 27 +++++++++++++++++++++++++++
5 files changed, 69 insertions(+), 3 deletions(-)
Index: linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/pme/pcie_pme.c
+++ linux-2.6/drivers/pci/pcie/pme/pcie_pme.c
@@ -53,12 +53,22 @@ static bool pcie_pme_disabled;
*/
static bool pcie_pme_force_enable;
+/*
+ * If this switch is set, MSI will not be used for PCIe PME signaling. This
+ * causes the PCIe port driver to use INTx interrupts only, but it turns out
+ * that using MSI for PCIe PME signaling doesn't play well with PCIe PME-based
+ * wake-up from system sleep states.
+ */
+bool pcie_pme_msi_disabled;
+
static int __init pcie_pme_setup(char *str)
{
if (!strcmp(str, "off"))
pcie_pme_disabled = true;
else if (!strcmp(str, "force"))
pcie_pme_force_enable = true;
+ else if (!strcmp(str, "nomsi"))
+ pcie_pme_msi_disabled = true;
return 1;
}
__setup("pcie_pme=", pcie_pme_setup);
@@ -73,7 +83,9 @@ __setup("pcie_pme=", pcie_pme_setup);
*/
static bool pcie_pme_platform_setup(struct pcie_device *srv)
{
- return !pcie_pme_platform_notify(srv) || pcie_pme_force_enable;
+ if (!pcie_pme_platform_notify(srv))
+ return true;
+ return pcie_pme_force_enable;
}
struct pcie_pme_service_data {
Index: linux-2.6/drivers/pci/pcie/portdrv_core.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv_core.c
+++ linux-2.6/drivers/pci/pcie/portdrv_core.c
@@ -186,16 +186,24 @@ static int pcie_port_enable_msix(struct
*/
static int init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
{
- int i, irq;
+ int i, irq = -1;
+
+ /* We have to use INTx if MSI cannot be used for PCIe PME. */
+ if ((mask & PCIE_PORT_SERVICE_PME) && pcie_pme_no_msi()) {
+ if (dev->pin)
+ irq = dev->irq;
+ goto no_msi;
+ }
/* Try to use MSI-X if supported */
if (!pcie_port_enable_msix(dev, irqs, mask))
return 0;
+
/* We're not going to use MSI-X, so try MSI and fall back to INTx */
- irq = -1;
if (!pci_enable_msi(dev) || dev->pin)
irq = dev->irq;
+ no_msi:
for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
irqs[i] = irq;
irqs[PCIE_PORT_SERVICE_VC_SHIFT] = -1;
Index: linux-2.6/drivers/pci/pcie/portdrv_pci.c
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv_pci.c
+++ linux-2.6/drivers/pci/pcie/portdrv_pci.c
@@ -15,6 +15,7 @@
#include <linux/slab.h>
#include <linux/pcieport_if.h>
#include <linux/aer.h>
+#include <linux/dmi.h>
#include "portdrv.h"
#include "aer/aerdrv.h"
@@ -273,10 +274,36 @@ static struct pci_driver pcie_portdriver
.driver.pm = PCIE_PORTDRV_PM_OPS,
};
+static int __init dmi_pcie_pme_disable_msi(const struct dmi_system_id *d)
+{
+ pr_notice("%s detected: will not use MSI for PCIe PME signaling\n",
+ d->ident);
+ pcie_pme_disable_msi();
+ return 0;
+}
+
+static struct dmi_system_id __initdata pcie_portdrv_dmi_table[] = {
+ /*
+ * Boxes that should not use MSI for PCIe PME signaling.
+ */
+ {
+ .callback = dmi_pcie_pme_disable_msi,
+ .ident = "MSI Wind U-100",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR,
+ "MICRO-STAR INTERNATIONAL CO., LTD"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "U-100"),
+ },
+ },
+ {}
+};
+
static int __init pcie_portdrv_init(void)
{
int retval;
+ dmi_check_system(pcie_portdrv_dmi_table);
+
retval = pcie_port_bus_register();
if (retval) {
printk(KERN_WARNING "PCIE: bus_register error: %d\n", retval);
Index: linux-2.6/drivers/pci/pcie/portdrv.h
===================================================================
--- linux-2.6.orig/drivers/pci/pcie/portdrv.h
+++ linux-2.6/drivers/pci/pcie/portdrv.h
@@ -30,4 +30,21 @@ extern void pcie_port_device_remove(stru
extern int __must_check pcie_port_bus_register(void);
extern void pcie_port_bus_unregister(void);
+#ifdef CONFIG_PCIE_PME
+extern bool pcie_pme_msi_disabled;
+
+static inline void pcie_pme_disable_msi(void)
+{
+ pcie_pme_msi_disabled = true;
+}
+
+static inline bool pcie_pme_no_msi(void)
+{
+ return pcie_pme_msi_disabled;
+}
+#else /* !CONFIG_PCIE_PME */
+static inline void pcie_pme_disable_msi(void) {}
+static inline bool pcie_pme_no_msi(void) { return false; }
+#endif /* !CONFIG_PCIE_PME */
+
#endif /* _PORTDRV_H_ */
Index: linux-2.6/Documentation/kernel-parameters.txt
===================================================================
--- linux-2.6.orig/Documentation/kernel-parameters.txt
+++ linux-2.6/Documentation/kernel-parameters.txt
@@ -1994,6 +1994,8 @@ and is between 256 and 4096 characters.
force Use native PCIe PME signaling even if the BIOS refuses
to allow the kernel to control the relevant PCIe config
registers.
+ nomsi Do not use MSI for native PCIe PME signaling (this makes
+ all PCIe root ports use INTx for everything).
pcmv= [HW,PCMCIA] BadgePAD 4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists