| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20100129160731.21495.95618.sendpatchset@localhost>
Date: Fri, 29 Jan 2010 17:07:31 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 41/68] pata_cmd64x: convert to ide2libata
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
Subject: [PATCH] pata_cmd64x: convert to ide2libata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
drivers/ata/pata_cmd64x.h | 35 +++++++-
drivers/ide/cmd64x.c | 195 +---------------------------------------------
2 files changed, 41 insertions(+), 189 deletions(-)
Index: b/drivers/ata/pata_cmd64x.h
===================================================================
--- a/drivers/ata/pata_cmd64x.h
+++ b/drivers/ata/pata_cmd64x.h
@@ -56,7 +56,12 @@ static void cmd64x_set_timing(struct ata
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_timing t;
+#ifndef __IDE2LIBATA
const unsigned long T = 1000000 / 33;
+#else
+ int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
+ const unsigned long T = 1000000 / bus_speed;
+#endif
const u8 setup_data[] = { 0x40, 0x40, 0x40, 0x80, 0x00 };
u8 reg;
@@ -124,6 +129,11 @@ static void cmd64x_set_timing(struct ata
/* Load setup timing */
pci_read_config_byte(pdev, arttim, ®);
+#ifdef __IDE2LIBATA
+ /* Avoid clearing the secondary channel's interrupt bit. */
+ if (ap->port_no)
+ reg &= ~ARTTIM23_INTR_CH1;
+#endif
reg &= 0x3F;
reg |= t.setup;
pci_write_config_byte(pdev, arttim, reg);
@@ -143,6 +153,13 @@ static void cmd64x_set_timing(struct ata
static void cmd64x_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
+#ifdef __IDE2LIBATA
+ const u8 pio = adev->pio_mode - XFER_PIO_0;
+
+ /* Filter out the prefetch control values. */
+ if (pio == 8 || pio == 9)
+ return;
+#endif
cmd64x_set_timing(ap, adev, adev->pio_mode);
}
@@ -161,13 +178,17 @@ static void cmd64x_set_dmamode(struct at
};
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u8 regU, regD;
+ u8 regU, regD = 0;
int pciU = UDIDETCR0 + 8 * ap->port_no;
+#ifndef __IDE2LIBATA
int pciD = BMIDESR0 + 8 * ap->port_no;
+#endif
int shift = 2 * adev->devno;
+#ifndef __IDE2LIBATA
pci_read_config_byte(pdev, pciD, ®D);
+#endif
pci_read_config_byte(pdev, pciU, ®U);
/* DMA bits off */
@@ -192,7 +213,9 @@ static void cmd64x_set_dmamode(struct at
regD |= 0x20 << adev->devno;
pci_write_config_byte(pdev, pciU, regU);
+#ifndef __IDE2LIBATA
pci_write_config_byte(pdev, pciD, regD);
+#endif
}
static int cmd64x_fixup(struct device *dev)
@@ -201,15 +224,23 @@ static int cmd64x_fixup(struct device *d
u8 mrdmode;
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 64);
+ /* FIXME: pci_set_master() to ensure a good latency timer value */
+
+ /*
+ * NOTE: although not mentioned in the PCI0646U specs,
+ * bits 0-1 are write only and won't be read back as
+ * set or not -- PCI0646U2 specs clarify this point.
+ */
pci_read_config_byte(pdev, MRDMODE, &mrdmode);
mrdmode &= ~0x30; /* IRQ set up */
mrdmode |= 0x02; /* Memory read line enable */
pci_write_config_byte(pdev, MRDMODE, mrdmode);
+#ifndef __IDE2LIBATA
/* PPC specific fixup copied from old driver */
#ifdef CONFIG_PPC
pci_write_config_byte(pdev, UDIDETCR0, 0xF0);
#endif
-
+#endif
return 0;
}
Index: b/drivers/ide/cmd64x.c
===================================================================
--- a/drivers/ide/cmd64x.c
+++ b/drivers/ide/cmd64x.c
@@ -20,168 +20,8 @@
#define DRV_NAME "cmd64x"
-/*
- * CMD64x specific registers definition.
- */
-#define CFR 0x50
-#define CFR_INTR_CH0 0x04
-
-#define CMDTIM 0x52
-#define ARTTIM0 0x53
-#define DRWTIM0 0x54
-#define ARTTIM1 0x55
-#define DRWTIM1 0x56
-#define ARTTIM23 0x57
-#define ARTTIM23_DIS_RA2 0x04
-#define ARTTIM23_DIS_RA3 0x08
-#define ARTTIM23_INTR_CH1 0x10
-#define DRWTIM2 0x58
-#define BRST 0x59
-#define DRWTIM3 0x5b
-
-#define BMIDECR0 0x70
-#define MRDMODE 0x71
-#define MRDMODE_INTR_CH0 0x04
-#define MRDMODE_INTR_CH1 0x08
-#define UDIDETCR0 0x73
-#define DTPR0 0x74
-#define BMIDECR1 0x78
-#define BMIDECSR 0x79
-#define UDIDETCR1 0x7B
-#define DTPR1 0x7C
-
-static void cmd64x_program_timings(ide_drive_t *drive, u8 mode)
-{
- ide_hwif_t *hwif = drive->hwif;
- struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
- int bus_speed = ide_pci_clk ? ide_pci_clk : 33;
- const unsigned long T = 1000000 / bus_speed;
- static const u8 recovery_values[] =
- {15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0};
- static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0};
- static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23};
- static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3};
- struct ata_timing t;
- u8 arttim = 0;
-
- ata_timing_compute(drive->id, mode, drive->pio_mode, &t, T, 0);
-
- /*
- * In case we've got too long recovery phase, try to lengthen
- * the active phase
- */
- if (t.recover > 16) {
- t.active += t.recover - 16;
- t.recover = 16;
- }
- if (t.active > 16) /* shouldn't actually happen... */
- t.active = 16;
-
- /*
- * Convert values to internal chipset representation
- */
- t.recover = recovery_values[t.recover];
- t.active &= 0x0f;
-
- /* Program the active/recovery counts into the DRWTIM register */
- pci_write_config_byte(dev, drwtim_regs[drive->dn],
- (t.active << 4) | t.recover);
-
- /*
- * The primary channel has individual address setup timing registers
- * for each drive and the hardware selects the slowest timing itself.
- * The secondary channel has one common register and we have to select
- * the slowest address setup timing ourselves.
- */
- if (hwif->channel) {
- ide_drive_t *pair = ide_get_pair_dev(drive);
-
- if (pair) {
- struct ata_timing tp;
-
- ata_timing_compute(pair->id, pair->pio_mode,
- pair->pio_mode, &tp, T, 0);
- ata_timing_merge(&t, &tp, &t, ATA_TIMING_SETUP);
- if (pair->dma_mode) {
- ata_timing_compute(pair->id, pair->dma_mode,
- pair->pio_mode, &tp, T, 0);
- ata_timing_merge(&tp, &t, &t, ATA_TIMING_SETUP);
- }
- }
- }
-
- if (t.setup > 5) /* shouldn't actually happen... */
- t.setup = 5;
-
- /*
- * Program the address setup clocks into the ARTTIM registers.
- * Avoid clearing the secondary channel's interrupt bit.
- */
- (void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim);
- if (hwif->channel)
- arttim &= ~ARTTIM23_INTR_CH1;
- arttim &= ~0xc0;
- arttim |= setup_values[t.setup];
- (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim);
-}
-
-/*
- * Attempts to set drive's PIO mode.
- * Special cases are 8: prefetch off, 9: prefetch on (both never worked)
- */
-
-static void cmd64x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- /*
- * Filter out the prefetch control values
- * to prevent PIO5 from being programmed
- */
- if (pio == 8 || pio == 9)
- return;
-
- cmd64x_program_timings(drive, XFER_PIO_0 + pio);
-}
-
-static void cmd64x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 unit = drive->dn & 0x01;
- u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0;
- const u8 speed = drive->dma_mode;
-
- pci_read_config_byte(dev, pciU, ®U);
- regU &= ~(unit ? 0xCA : 0x35);
-
- switch(speed) {
- case XFER_UDMA_5:
- regU |= unit ? 0x0A : 0x05;
- break;
- case XFER_UDMA_4:
- regU |= unit ? 0x4A : 0x15;
- break;
- case XFER_UDMA_3:
- regU |= unit ? 0x8A : 0x25;
- break;
- case XFER_UDMA_2:
- regU |= unit ? 0x42 : 0x11;
- break;
- case XFER_UDMA_1:
- regU |= unit ? 0x82 : 0x21;
- break;
- case XFER_UDMA_0:
- regU |= unit ? 0xC2 : 0x31;
- break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_MW_DMA_0:
- cmd64x_program_timings(drive, speed);
- break;
- }
-
- pci_write_config_byte(dev, pciU, regU);
-}
+#include <linux/ide2libata.h>
+#include "../ata/pata_cmd64x.h"
static void cmd648_clear_irq(ide_drive_t *drive)
{
@@ -265,52 +105,33 @@ static int cmd646_1_dma_end(ide_drive_t
static int init_chipset_cmd64x(struct pci_dev *dev)
{
- u8 mrdmode = 0;
-
- /* Set a good latency timer and cache line size value. */
- (void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64);
- /* FIXME: pci_set_master() to ensure a good latency timer value */
-
- /*
- * Enable interrupts, select MEMORY READ LINE for reads.
- *
- * NOTE: although not mentioned in the PCI0646U specs,
- * bits 0-1 are write only and won't be read back as
- * set or not -- PCI0646U2 specs clarify this point.
- */
- (void) pci_read_config_byte (dev, MRDMODE, &mrdmode);
- mrdmode &= ~0x30;
- (void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02));
-
- return 0;
+ return cmd64x_fixup(&dev->dev);
}
static int cmd64x_cable_detect(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01;
switch (dev->device) {
case PCI_DEVICE_ID_CMD_648:
case PCI_DEVICE_ID_CMD_649:
- pci_read_config_byte(dev, BMIDECSR, &bmidecsr);
- return (bmidecsr & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+ return cmd648_cable_detect(hwif);
default:
return ATA_CBL_PATA40;
}
}
static const struct ide_port_ops cmd64x_port_ops = {
- .set_pio_mode = cmd64x_set_pio_mode,
- .set_dma_mode = cmd64x_set_dma_mode,
+ .set_pio_mode = cmd64x_set_piomode,
+ .set_dma_mode = cmd64x_set_dmamode,
.clear_irq = cmd64x_clear_irq,
.test_irq = cmd64x_test_irq,
.cable_detect = cmd64x_cable_detect,
};
static const struct ide_port_ops cmd648_port_ops = {
- .set_pio_mode = cmd64x_set_pio_mode,
- .set_dma_mode = cmd64x_set_dma_mode,
+ .set_pio_mode = cmd64x_set_piomode,
+ .set_dma_mode = cmd64x_set_dmamode,
.clear_irq = cmd648_clear_irq,
.test_irq = cmd648_test_irq,
.cable_detect = cmd64x_cable_detect,
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists