| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20100129160810.21495.19266.sendpatchset@localhost>
Date: Fri, 29 Jan 2010 17:08:10 +0100
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
To: linux-ide@...r.kernel.org
Cc: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH 47/68] cs5535: convert to ide2libata
From: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
Subject: [PATCH] cs5535: convert to ide2libata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@...il.com>
---
drivers/ide/cs5535.c | 141 +--------------------------------------------------
1 file changed, 4 insertions(+), 137 deletions(-)
Index: b/drivers/ide/cs5535.c
===================================================================
--- a/drivers/ide/cs5535.c
+++ b/drivers/ide/cs5535.c
@@ -28,145 +28,12 @@
#define DRV_NAME "cs5535"
-#define MSR_ATAC_BASE 0x51300000
-#define ATAC_GLD_MSR_CAP (MSR_ATAC_BASE+0)
-#define ATAC_GLD_MSR_CONFIG (MSR_ATAC_BASE+0x01)
-#define ATAC_GLD_MSR_SMI (MSR_ATAC_BASE+0x02)
-#define ATAC_GLD_MSR_ERROR (MSR_ATAC_BASE+0x03)
-#define ATAC_GLD_MSR_PM (MSR_ATAC_BASE+0x04)
-#define ATAC_GLD_MSR_DIAG (MSR_ATAC_BASE+0x05)
-#define ATAC_IO_BAR (MSR_ATAC_BASE+0x08)
-#define ATAC_RESET (MSR_ATAC_BASE+0x10)
-#define ATAC_CH0D0_PIO (MSR_ATAC_BASE+0x20)
-#define ATAC_CH0D0_DMA (MSR_ATAC_BASE+0x21)
-#define ATAC_CH0D1_PIO (MSR_ATAC_BASE+0x22)
-#define ATAC_CH0D1_DMA (MSR_ATAC_BASE+0x23)
-#define ATAC_PCI_ABRTERR (MSR_ATAC_BASE+0x24)
-#define ATAC_BM0_CMD_PRIM 0x00
-#define ATAC_BM0_STS_PRIM 0x02
-#define ATAC_BM0_PRD 0x04
-#define CS5535_CABLE_DETECT 0x48
-
-/* Format I PIO settings. We separate out cmd and data for safer timings */
-
-static unsigned int cs5535_pio_cmd_timings[5] =
-{ 0xF7F4, 0x53F3, 0x13F1, 0x5131, 0x1131 };
-static unsigned int cs5535_pio_dta_timings[5] =
-{ 0xF7F4, 0xF173, 0x8141, 0x5131, 0x1131 };
-
-static unsigned int cs5535_mwdma_timings[3] =
-{ 0x7F0FFFF3, 0x7F035352, 0x7f024241 };
-
-static unsigned int cs5535_udma_timings[5] =
-{ 0x7F7436A1, 0x7F733481, 0x7F723261, 0x7F713161, 0x7F703061 };
-
-/* Macros to check if the register is the reset value - reset value is an
- invalid timing and indicates the register has not been set previously */
-
-#define CS5535_BAD_PIO(timings) ( (timings&~0x80000000UL) == 0x00009172 )
-#define CS5535_BAD_DMA(timings) ( (timings & 0x000FFFFF) == 0x00077771 )
-
-/****
- * cs5535_set_speed - Configure the chipset to the new speed
- * @drive: Drive to set up
- * @speed: desired speed
- *
- * cs5535_set_speed() configures the chipset to a new speed.
- */
-static void cs5535_set_speed(ide_drive_t *drive, const u8 speed)
-{
- u32 reg = 0, dummy;
- u8 unit = drive->dn & 1;
-
- /* Set the PIO timings */
- if (speed < XFER_SW_DMA_0) {
- ide_drive_t *pair = ide_get_pair_dev(drive);
- u8 cmd, pioa;
-
- cmd = pioa = speed - XFER_PIO_0;
-
- if (pair) {
- u8 piob = pair->pio_mode - XFER_PIO_0;
-
- if (piob < cmd)
- cmd = piob;
- }
-
- /* Write the speed of the current drive */
- reg = (cs5535_pio_cmd_timings[cmd] << 16) |
- cs5535_pio_dta_timings[pioa];
- wrmsr(unit ? ATAC_CH0D1_PIO : ATAC_CH0D0_PIO, reg, 0);
-
- /* And if nessesary - change the speed of the other drive */
- rdmsr(unit ? ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, dummy);
-
- if (((reg >> 16) & cs5535_pio_cmd_timings[cmd]) !=
- cs5535_pio_cmd_timings[cmd]) {
- reg &= 0x0000FFFF;
- reg |= cs5535_pio_cmd_timings[cmd] << 16;
- wrmsr(unit ? ATAC_CH0D0_PIO : ATAC_CH0D1_PIO, reg, 0);
- }
-
- /* Set bit 31 of the DMA register for PIO format 1 timings */
- rdmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
- wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA,
- reg | 0x80000000UL, 0);
- } else {
- rdmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, dummy);
-
- reg &= 0x80000000UL; /* Preserve the PIO format bit */
-
- if (speed >= XFER_UDMA_0 && speed <= XFER_UDMA_4)
- reg |= cs5535_udma_timings[speed - XFER_UDMA_0];
- else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
- reg |= cs5535_mwdma_timings[speed - XFER_MW_DMA_0];
- else
- return;
-
- wrmsr(unit ? ATAC_CH0D1_DMA : ATAC_CH0D0_DMA, reg, 0);
- }
-}
-
-/**
- * cs5535_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Programs the chipset for DMA mode.
- */
-
-static void cs5535_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- cs5535_set_speed(drive, drive->dma_mode);
-}
-
-/**
- * cs5535_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * A callback from the upper layers for PIO-only tuning.
- */
-
-static void cs5535_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- cs5535_set_speed(drive, drive->pio_mode);
-}
-
-static int cs5535_cable_detect(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- u8 bit;
-
- /* if a 80 wire cable was detected */
- pci_read_config_byte(dev, CS5535_CABLE_DETECT, &bit);
-
- return (bit & 1) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
-}
+#include <linux/ide2libata.h>
+#include "../ata/pata_cs5535.h"
static const struct ide_port_ops cs5535_port_ops = {
- .set_pio_mode = cs5535_set_pio_mode,
- .set_dma_mode = cs5535_set_dma_mode,
+ .set_pio_mode = cs5535_set_piomode,
+ .set_dma_mode = cs5535_set_dmamode,
.cable_detect = cs5535_cable_detect,
};
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists