| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <201001301734.46003.wolfgang.walter@stwm.de> Date: Sat, 30 Jan 2010 17:34:45 +0100 From: Wolfgang Walter <wolfgang.walter@...m.de> To: Herbert Xu <herbert@...dor.apana.org.au> Cc: "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>, "netdev@...r.kernel.org" <netdev@...r.kernel.org> Subject: Re: 2.6.32: padlock_sha1 and hmac broken? Am Samstag, 30. Januar 2010 schrieben Sie: > On Sat, Jan 30, 2010 at 12:44:15AM +0100, Wolfgang Walter wrote: > > Hello, > > > > I upgraded some machines with VIA processors from (vanilla) 2.6.31 to > > 2.6.32.7. > > > > If I build the kernel 2.6.32.7 with CONFIG_CRYPTO_DEV_PADLOCK_SHA=y and > > padlock supports sha, hmac(sha1) is missing and IPSEC with hmac(sha1) no > > longer is possible. > > Can you please attach the dmesg output so we can see if there > were any error messages? ============= E# disabled [ 0.144494] HPET not enabled in BIOS. You might try hpet=force boot option [ 0.144634] pci 0000:00:11.5: reg 10 io port: [0xec00-0xecff] [ 0.144698] pci 0000:00:11.5: supports D1 D2 [ 0.144787] pci 0000:01:00.0: reg 10 32bit mmio pref: [0xf4000000-0xf7ffffff] [ 0.144803] pci 0000:01:00.0: reg 14 32bit mmio: [0xfb000000-0xfbffffff] [ 0.144835] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] [ 0.144865] pci 0000:01:00.0: supports D1 D2 [ 0.144921] pci 0000:00:01.0: bridge io port: [0xd000-0xdfff] [ 0.144933] pci 0000:00:01.0: bridge 32bit mmio: [0xfb000000-0xfcffffff] [ 0.144946] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf4000000-0xf7ffffff] [ 0.144965] pci_bus 0000:00: on NUMA node 0 [ 0.144985] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.327624] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 11 12) *5 [ 0.328584] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12) [ 0.329501] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12) [ 0.330402] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled. [ 0.331336] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. [ 0.332247] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. [ 0.333159] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. [ 0.334095] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. [ 0.335140] ACPI: PCI Interrupt Link [ALKA] (IRQs *20) [ 0.335828] ACPI: PCI Interrupt Link [ALKB] (IRQs *21) [ 0.336519] ACPI: PCI Interrupt Link [ALKC] (IRQs *22) [ 0.337280] ACPI: PCI Interrupt Link [ALKD] (IRQs *23), disabled. [ 0.337998] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none [ 0.338080] vgaarb: loaded [ 0.338528] SCSI subsystem initialized [ 0.338658] libata version 3.00 loaded. [ 0.339062] usbcore: registered new interface driver usbfs [ 0.339205] usbcore: registered new interface driver hub [ 0.339364] usbcore: registered new device driver usb [ 0.339798] PCI: Using ACPI for IRQ routing [ 0.340410] Switching to clocksource tsc [ 0.340531] pnp: PnP ACPI init [ 0.340606] ACPI: bus type pnp registered [ 0.354181] pnp: PnP ACPI: found 11 devices [ 0.354252] ACPI: ACPI bus type pnp unregistered [ 0.354343] system 00:00: iomem range 0xf0000-0xfffff could not be reserved [ 0.354415] system 00:00: iomem range 0x1eee0000-0x1eefffff could not be reserved [ 0.354496] system 00:00: iomem range 0xffff0000-0xffffffff has been reserved [ 0.354568] system 00:00: iomem range 0x0-0x9ffff could not be reserved [ 0.354638] system 00:00: iomem range 0x100000-0x1eedffff could not be reserved [ 0.354717] system 00:00: iomem range 0xfec00000-0xfec00fff could not be reserved [ 0.354797] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.354869] system 00:00: iomem range 0xfff80000-0xfffeffff has been reserved [ 0.354951] system 00:02: ioport range 0x400-0x47f has been reserved [ 0.355020] system 00:02: ioport range 0x500-0x50f has been reserved [ 0.355131] system 00:03: ioport range 0x4d0-0x4d1 has been reserved [ 0.355200] system 00:03: ioport range 0x800-0x87f has been reserved [ 0.355269] system 00:03: ioport range 0x880-0x8ff has been reserved [ 0.391005] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.391081] pci 0000:00:01.0: IO window: 0xd000-0xdfff [ 0.391151] pci 0000:00:01.0: MEM window: 0xfb000000-0xfcffffff [ 0.391222] pci 0000:00:01.0: PREFETCH window: 0xf4000000-0xf7ffffff [ 0.391311] pci 0000:00:01.0: setting latency timer to 64 [ 0.391326] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.391337] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.391348] pci_bus 0000:01: resource 0 io: [0xd000-0xdfff] [ 0.391359] pci_bus 0000:01: resource 1 mem: [0xfb000000-0xfcffffff] [ 0.391370] pci_bus 0000:01: resource 2 pref mem [0xf4000000-0xf7ffffff] [ 0.391471] NET: Registered protocol family 2 [ 0.391849] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.392765] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.393170] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.394127] TCP: Hash tables configured (established 16384 bind 16384) [ 0.394195] TCP reno registered [ 0.394459] NET: Registered protocol family 1 [ 0.394579] pci 0000:00:01.0: disabling DAC on VIA PCI bridge [ 0.394773] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message [ 0.394853] pci 0000:01:00.0: Boot video device [ 0.394985] Trying to unpack rootfs image as initramfs... [ 0.397158] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 0.583043] Freeing initrd memory: 42677k freed [ 0.657473] cpufreq-nforce2: No nForce2 chipset. [ 0.667097] msgmni has been set to 970 [ 0.667379] alg: No test for cipher_null (cipher_null-generic) [ 0.667498] alg: No test for ecb(cipher_null) (ecb-cipher_null) [ 0.667610] alg: No test for digest_null (digest_null-generic) [ 0.667718] alg: No test for compress_null (compress_null-generic) [ 0.670760] alg: No test for fcrypt (fcrypt-generic) [ 0.679058] alg: No test for stdrng (krng) [ 0.716094] alg: No test for ghash (ghash-generic) [ 0.716212] io scheduler noop registered [ 0.716272] io scheduler anticipatory registered [ 0.716334] io scheduler deadline registered [ 0.716680] io scheduler cfq registered (default) [ 0.717179] fan PNP0C0B:00: registered as cooling_device0 [ 0.717255] ACPI: Fan [FAN] (on) [ 0.717565] processor LNXCPU:00: registered as cooling_device1 [ 0.719182] thermal LNXTHERM:01: registered as thermal_zone0 [ 0.719267] ACPI: Thermal Zone [THRM] (-248 C) [ 0.727205] Real Time Clock Driver v1.12b [ 0.727761] VIA RNG detected [ 0.727936] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.728201] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.728473] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.729423] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.729847] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.734418] brd: module loaded [ 0.736455] loop: module loaded [ 0.737003] sata_via 0000:00:0f.0: version 2.4 [ 0.737729] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20 [ 0.737818] sata_via 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20 [ 0.737980] sata_via 0000:00:0f.0: routed to hard irq line 11 [ 0.738200] scsi0 : sata_via [ 0.738633] scsi1 : sata_via [ 0.743265] ata1: SATA max UDMA/133 cmd 0xff00 ctl 0xfe00 bmdma 0xfb00 irq 20 [ 0.743344] ata2: SATA max UDMA/133 cmd 0xfd00 ctl 0xfc00 bmdma 0xfb08 irq 20 [ 0.744718] pata_via 0000:00:0f.1: version 0.3.4 [ 0.744767] pata_via 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20 [ 0.745103] scsi2 : pata_via [ 0.745412] scsi3 : pata_via [ 0.749245] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfa00 irq 14 [ 0.749322] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfa08 irq 15 [ 0.751538] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI [ 0.751614] Copyright (c) 1999-2006 Intel Corporation. [ 0.751788] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 [ 0.751854] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 0.752023] Intel(R) Gigabit Ethernet Network Driver - version 1.3.16-k2 [ 0.752091] Copyright (c) 2007-2009 Intel Corporation. [ 0.752247] Ethernet Channel Bonding Driver: v3.5.0 (November 4, 2008) [ 0.752318] bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details. [ 0.753414] Atheros(R) L2 Ethernet Driver - version 2.2.3 [ 0.753481] Copyright (c) 2007 Atheros Corporation. [ 0.753651] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI [ 0.753717] e100: Copyright(c) 1999-2006 Intel Corporation [ 0.754053] via-rhine: Broken BIOS detected, avoid_D3 enabled. [ 0.754409] PPP generic driver version 2.4.2 [ 0.754714] PPP Deflate Compression module registered [ 0.754779] NET: Registered protocol family 24 [ 0.754865] PPPoL2TP kernel driver, V1.0 [ 0.755766] 8139too Fast Ethernet driver 0.9.28 [ 0.755863] 8139too 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.757379] eth0: RealTek RTL8139 at 0xdf7d2000, 00:30:18:4c:69:5f, IRQ 16 [ 0.757495] 8139too 0000:00:06.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.758684] eth1: RealTek RTL8139 at 0xdf7d6000, 00:30:18:4c:69:5e, IRQ 17 [ 0.758785] 8139too 0000:00:07.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 0.760026] eth2: RealTek RTL8139 at 0xdf7da000, 00:30:18:4c:69:5d, IRQ 18 [ 0.760197] tun: Universal TUN/TAP device driver, 1.6 [ 0.760260] tun: (C) 1999-2004 Max Krasnyansky <maxk@...lcomm.com> [ 0.761031] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.761857] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21 [ 0.761940] ehci_hcd 0000:00:10.4: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 0.762052] ehci_hcd 0000:00:10.4: EHCI Host Controller [ 0.762355] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 [ 0.762532] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdffc000 [ 0.769490] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00 [ 0.769830] usb usb1: configuration #1 chosen from 1 choice [ 0.770025] hub 1-0:1.0: USB hub found [ 0.770103] hub 1-0:1.0: 8 ports detected [ 0.770359] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.770533] uhci_hcd: USB Universal Host Controller Interface driver [ 0.770727] uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 0.770820] uhci_hcd 0000:00:10.0: UHCI Host Controller [ 0.771050] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 [ 0.771162] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000f900 [ 0.771537] usb usb2: configuration #1 chosen from 1 choice [ 0.771724] hub 2-0:1.0: USB hub found [ 0.771802] hub 2-0:1.0: 2 ports detected [ 0.771986] uhci_hcd 0000:00:10.1: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 0.772076] uhci_hcd 0000:00:10.1: UHCI Host Controller [ 0.772300] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 [ 0.772412] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000f800 [ 0.772780] usb usb3: configuration #1 chosen from 1 choice [ 0.773014] hub 3-0:1.0: USB hub found [ 0.773090] hub 3-0:1.0: 2 ports detected [ 0.773289] uhci_hcd 0000:00:10.2: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 0.773381] uhci_hcd 0000:00:10.2: UHCI Host Controller [ 0.773597] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 [ 0.773709] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000f700 [ 0.774087] usb usb4: configuration #1 chosen from 1 choice [ 0.774286] hub 4-0:1.0: USB hub found [ 0.774362] hub 4-0:1.0: 2 ports detected [ 0.774543] uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21 [ 0.774632] uhci_hcd 0000:00:10.3: UHCI Host Controller [ 0.774849] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 [ 0.774961] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000f600 [ 0.775332] usb usb5: configuration #1 chosen from 1 choice [ 0.775528] hub 5-0:1.0: USB hub found [ 0.775605] hub 5-0:1.0: 2 ports detected [ 0.775847] Initializing USB Mass Storage driver... [ 0.776082] usbcore: registered new interface driver usb-storage [ 0.776240] USB Mass Storage support registered. [ 0.776614] PNP: No PS/2 controller found. Probing ports directly. [ 0.952805] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300) [ 1.039562] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.040107] mice: PS/2 mouse device common for all mice [ 1.040511] vt1211: Found VT1211 chip at 0x6000, revision 2 [ 1.040751] hwmon-vid: Unknown VRM version of your x86 CPU [ 1.041244] EDAC MC: Ver: 2.1.0 Jan 29 2010 [ 1.041624] cpuidle: using governor ladder [ 1.041985] padlock: Using VIA PadLock ACE for AES algorithm. [ 1.042208] padlock: Using VIA PadLock ACE for SHA1/SHA256 algorithms. [ 1.044696] usbcore: registered new interface driver hiddev [ 1.044855] usbcore: registered new interface driver usbhid [ 1.044921] usbhid: v2.6:USB HID core driver [ 1.045210] GACT probability on [ 1.045269] Mirror/redirect action on [ 1.045329] Simple TC action Loaded [ 1.046549] netem: version 1.2 [ 1.046610] u32 classifier [ 1.046664] Performance counters on [ 1.046722] input device check on [ 1.046779] Actions configured [ 1.046842] Netfilter messages via NETLINK v0.30. [ 1.047083] xt_time: kernel timezone is -0000 [ 1.048522] IPv4 over IPv4 tunneling driver [ 1.050009] GRE over IPv4 tunneling driver [ 1.051417] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.051547] arp_tables: (C) 2002 David S. Miller [ 1.051695] TCP cubic registered [ 1.051752] Initializing XFRM netlink socket [ 1.051816] IPv6: Loaded, but administratively disabled, reboot required to enable [ 1.051892] ipv6 ah init: can't add xfrm type [ 1.051952] ipv6 esp init: can't add xfrm type [ 1.052012] ipcomp6 init: can't add xfrm type [ 1.052089] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.052212] IPv6 over IPv4 tunneling driver [ 1.054635] NET: Registered protocol family 17 [ 1.054715] NET: Registered protocol family 15 [ 1.055004] Bridge firewalling registered [ 1.055071] Ebtables v2.0 registered [ 1.055189] 802.1Q VLAN Support v1.8 Ben Greear <greearb@...delatech.com> [ 1.055256] All bugs added by David S. Miller <davem@...hat.com> [ 1.055363] Using IPI Shortcut mode [ 1.166687] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300) [ 1.357068] ata4.00: ATA-0: TRANSCEND, 20070312, max MWDMA2 [ 1.357136] ata4.00: 996912 sectors, multi 0: LBA [ 1.370307] ata4.00: configured for PIO4 [ 1.390304] ata4.00: configured for PIO4 [ 1.390365] ata4: EH complete [ 1.403538] scsi 3:0:0:0: Direct-Access ATA TRANSCEND 2007 PQ: 0 ANSI: 5 [ 1.404179] sd 3:0:0:0: [sda] 996912 512-byte logical blocks: (510 MB/486 MiB) [ 1.404337] sd 3:0:0:0: [sda] Write Protect is off [ 1.404403] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.404450] sd 3:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1.404811] sda: sda1 [ 1.406838] sd 3:0:0:0: Attached scsi generic sg0 type 0 [ 1.407324] sd 3:0:0:0: [sda] Attached SCSI disk [ 1.426851] RAMDISK: gzip image found at block 0 [ 8.951329] VFS: Mounted root (ext2 filesystem) readonly on device 1:0. [ 8.951452] devtmpfs: mounted [ 8.951542] Freeing unused kernel memory: 316k freed [ 10.473262] IPv4 FIB: Using LC-trie version 0.409 [ 10.917146] eth2: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 10.917722] eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1 [ 10.918198] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 [ 11.885269] nf_conntrack version 0.5.0 (7766 buckets, 31064 max) [ 11.885768] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 11.885778] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 11.885786] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ============= > > Please also try "modprobe tcrypt mode=101". > [ 474.947508] alg: hash: Failed to load transform for hmac(sha1): -2 [ 474.952660] alg: hash: Failed to load transform for hmac(sha1): -2 [ 474.952737] tcrypt: one or more tests failed! Regards, -- Wolfgang Walter Studentenwerk München Anstalt des öffentlichen Rechts -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@...r.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists