| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1266014143-29444-15-git-send-email-jason.wessel@windriver.com>
Date: Fri, 12 Feb 2010 16:35:29 -0600
From: Jason Wessel <jason.wessel@...driver.com>
To: linux-kernel@...r.kernel.org
Cc: kgdb-bugreport@...ts.sourceforge.net, mingo@...e.hu,
Jason Wessel <jason.wessel@...driver.com>,
Dmitry Torokhov <dmitry.torokhov@...il.com>
Subject: [PATCH 14/28] kgdboc,keyboard: Keyboard driver for kdb with kgdb
This patch adds in the kdb PS/2 keyboard driver. This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.
This patch also enables early kdb debug via kgdbwait and the keyboard.
All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.
If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:
kgdboc=kbd kgdbwait
If you wanted serial and or the keyboard access you could use:
kgdboc=kbd,ttyS0
You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.
Turn it on:
echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc
Turn it off:
echo "" > /sys/module/kgdboc/parameters/kgdboc
CC: Dmitry Torokhov <dmitry.torokhov@...il.com>
Signed-off-by: Jason Wessel <jason.wessel@...driver.com>
---
Documentation/kernel-parameters.txt | 8 +-
drivers/char/Makefile | 1 +
drivers/char/kdb_keyboard.c | 204 +++++++++++++++++++++++++++++++++++
drivers/char/kdb_keyboard.h | 143 ++++++++++++++++++++++++
drivers/serial/kgdboc.c | 61 +++++++++--
lib/Kconfig.kgdb | 7 ++
6 files changed, 414 insertions(+), 10 deletions(-)
create mode 100644 drivers/char/kdb_keyboard.c
create mode 100644 drivers/char/kdb_keyboard.h
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 736d456..f3be1e6 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1103,9 +1103,11 @@ and is between 256 and 4096 characters. It is defined in the file
zone if it does not.
kgdboc= [HW] kgdb over consoles.
- Requires a tty driver that supports console polling.
- (only serial supported for now)
- Format: <serial_device>[,baud]
+ Requires a tty driver that supports console polling,
+ or a supported polling keyboard driver (non-usb).
+ Serial only format: <serial_device>[,baud]
+ keyboard only format: kbd
+ keyboard and serial format: kbd,<serial_device>[,baud]
kmac= [MIPS] korina ethernet MAC address.
Configure the RouterBoard 532 series on-chip
diff --git a/drivers/char/Makefile b/drivers/char/Makefile
index f957edf..dbc579e 100644
--- a/drivers/char/Makefile
+++ b/drivers/char/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_LEGACY_PTYS) += pty.o
obj-$(CONFIG_UNIX98_PTYS) += pty.o
obj-y += misc.o
obj-$(CONFIG_VT) += vt_ioctl.o vc_screen.o selection.o keyboard.o
+obj-$(CONFIG_KDB_KEYBOARD) += kdb_keyboard.o
obj-$(CONFIG_BFIN_JTAG_COMM) += bfin_jtag_comm.o
obj-$(CONFIG_CONSOLE_TRANSLATIONS) += consolemap.o consolemap_deftbl.o
obj-$(CONFIG_HW_CONSOLE) += vt.o defkeymap.o
diff --git a/drivers/char/kdb_keyboard.c b/drivers/char/kdb_keyboard.c
new file mode 100644
index 0000000..95aa102
--- /dev/null
+++ b/drivers/char/kdb_keyboard.c
@@ -0,0 +1,204 @@
+/*
+ * Kernel Debugger Architecture Dependent Console I/O handler
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.
+ *
+ * Copyright (c) 1999-2006 Silicon Graphics, Inc. All Rights Reserved.
+ * Copyright (c) 2009 Wind River Systems, Inc. All Rights Reserved.
+ */
+
+#include <linux/kdb.h>
+#include <linux/keyboard.h>
+#include <linux/ctype.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include "kdb_keyboard.h"
+
+
+static int kbd_exists;
+
+/*
+ * Check if the keyboard controller has a keypress for us.
+ * Some parts (Enter Release, LED change) are still blocking polled here,
+ * but hopefully they are all short.
+ */
+int kdb_get_kbd_char(void)
+{
+ int scancode, scanstatus;
+ static int shift_lock; /* CAPS LOCK state (0-off, 1-on) */
+ static int shift_key; /* Shift next keypress */
+ static int ctrl_key;
+ u_short keychar;
+
+ if (KDB_FLAG(NO_I8042) || KDB_FLAG(NO_VT_CONSOLE) ||
+ (inb(KBD_STATUS_REG) == 0xff && inb(KBD_DATA_REG) == 0xff)) {
+ kbd_exists = 0;
+ return -1;
+ }
+ kbd_exists = 1;
+
+ if ((inb(KBD_STATUS_REG) & KBD_STAT_OBF) == 0)
+ return -1;
+
+ /*
+ * Fetch the scancode
+ */
+ scancode = inb(KBD_DATA_REG);
+ scanstatus = inb(KBD_STATUS_REG);
+
+ /*
+ * Ignore mouse events.
+ */
+ if (scanstatus & KBD_STAT_MOUSE_OBF)
+ return -1;
+
+ /*
+ * Ignore release, trigger on make
+ * (except for shift keys, where we want to
+ * keep the shift state so long as the key is
+ * held down).
+ */
+
+ if (((scancode&0x7f) == 0x2a) || ((scancode&0x7f) == 0x36)) {
+ /*
+ * Next key may use shift table
+ */
+ if ((scancode & 0x80) == 0)
+ shift_key = 1;
+ else
+ shift_key = 0;
+ return -1;
+ }
+
+ if ((scancode&0x7f) == 0x1d) {
+ /*
+ * Left ctrl key
+ */
+ if ((scancode & 0x80) == 0)
+ ctrl_key = 1;
+ else
+ ctrl_key = 0;
+ return -1;
+ }
+
+ if ((scancode & 0x80) != 0)
+ return -1;
+
+ scancode &= 0x7f;
+
+ /*
+ * Translate scancode
+ */
+
+ if (scancode == 0x3a) {
+ /*
+ * Toggle caps lock
+ */
+ shift_lock ^= 1;
+
+#ifdef KDB_BLINK_LED
+ kdb_toggleled(0x4);
+#endif
+ return -1;
+ }
+
+ if (scancode == 0x0e) {
+ /*
+ * Backspace
+ */
+ return 8;
+ }
+
+ /* Special Key */
+ switch (scancode) {
+ case 0xF: /* Tab */
+ return 9;
+ case 0x53: /* Del */
+ return 4;
+ case 0x47: /* Home */
+ return 1;
+ case 0x4F: /* End */
+ return 5;
+ case 0x4B: /* Left */
+ return 2;
+ case 0x48: /* Up */
+ return 16;
+ case 0x50: /* Down */
+ return 14;
+ case 0x4D: /* Right */
+ return 6;
+ }
+
+ if (scancode == 0xe0)
+ return -1;
+
+ /*
+ * For Japanese 86/106 keyboards
+ * See comment in drivers/char/pc_keyb.c.
+ * - Masahiro Adegawa
+ */
+ if (scancode == 0x73)
+ scancode = 0x59;
+ else if (scancode == 0x7d)
+ scancode = 0x7c;
+
+ if (!shift_lock && !shift_key && !ctrl_key) {
+ keychar = plain_map[scancode];
+ } else if ((shift_lock || shift_key) && key_maps[1]) {
+ keychar = key_maps[1][scancode];
+ } else if (ctrl_key && key_maps[4]) {
+ keychar = key_maps[4][scancode];
+ } else {
+ keychar = 0x0020;
+ kdb_printf("Unknown state/scancode (%d)\n", scancode);
+ }
+ keychar &= 0x0fff;
+ if (keychar == '\t')
+ keychar = ' ';
+ switch (KTYP(keychar)) {
+ case KT_LETTER:
+ case KT_LATIN:
+ if (isprint(keychar))
+ break; /* printable characters */
+ /* drop through */
+ case KT_SPEC:
+ if (keychar == K_ENTER)
+ break;
+ /* drop through */
+ default:
+ return -1; /* ignore unprintables */
+ }
+
+ if ((scancode & 0x7f) == 0x1c) {
+ /*
+ * enter key. All done. Absorb the release scancode.
+ */
+ while ((inb(KBD_STATUS_REG) & KBD_STAT_OBF) == 0)
+ ;
+
+ /*
+ * Fetch the scancode
+ */
+ scancode = inb(KBD_DATA_REG);
+ scanstatus = inb(KBD_STATUS_REG);
+
+ while (scanstatus & KBD_STAT_MOUSE_OBF) {
+ scancode = inb(KBD_DATA_REG);
+ scanstatus = inb(KBD_STATUS_REG);
+ }
+
+ if (scancode != 0x9c) {
+ /*
+ * Wasn't an enter-release, why not?
+ */
+ kdb_printf("kdb: expected enter got 0x%x status 0x%x\n",
+ scancode, scanstatus);
+ }
+
+ return 13;
+ }
+
+ return keychar & 0xff;
+}
+EXPORT_SYMBOL_GPL(kdb_get_kbd_char);
diff --git a/drivers/char/kdb_keyboard.h b/drivers/char/kdb_keyboard.h
new file mode 100644
index 0000000..5541668
--- /dev/null
+++ b/drivers/char/kdb_keyboard.h
@@ -0,0 +1,143 @@
+/*
+ * include/linux/pc_keyb.h
+ *
+ * PC Keyboard And Keyboard Controller
+ *
+ * (c) 1997 Martin Mares <mj@...ey.karlin.mff.cuni.cz>
+ */
+
+/*
+ * Configuration Switches
+ */
+
+#undef KBD_REPORT_ERR /* Report keyboard errors */
+#define KBD_REPORT_UNKN /* Report unknown scan codes */
+#define KBD_REPORT_TIMEOUTS /* Report keyboard timeouts */
+#undef KBD_IS_FOCUS_9000 /* We have the brain-damaged
+ * FOCUS-9000 keyboard */
+#undef INITIALIZE_MOUSE /* Define if your PS/2 mouse
+ * needs initialization. */
+
+#define KBD_INIT_TIMEOUT 1000 /* Timeout in ms for initializing the
+ * keyboard */
+#define KBC_TIMEOUT 250 /* Timeout in ms for sending
+ * to keyboard controller */
+#define KBD_TIMEOUT 1000 /* Timeout in ms for keyboard
+ * command acknowledge */
+
+/*
+ * Internal variables of the driver
+ */
+
+extern unsigned char pckbd_read_mask;
+extern unsigned char aux_device_present;
+
+/*
+ * Keyboard Controller Registers on normal PCs.
+ */
+
+#define KBD_STATUS_REG 0x64 /* Status register (R) */
+#define KBD_CNTL_REG 0x64 /* Controller command register (W) */
+#define KBD_DATA_REG 0x60 /* Keyboard data register (R/W) */
+
+/*
+ * Keyboard Controller Commands
+ */
+
+#define KBD_CCMD_READ_MODE 0x20 /* Read mode bits */
+#define KBD_CCMD_WRITE_MODE 0x60 /* Write mode bits */
+#define KBD_CCMD_GET_VERSION 0xA1 /* Get controller version */
+#define KBD_CCMD_MOUSE_DISABLE 0xA7 /* Disable mouse interface */
+#define KBD_CCMD_MOUSE_ENABLE 0xA8 /* Enable mouse interface */
+#define KBD_CCMD_TEST_MOUSE 0xA9 /* Mouse interface test */
+#define KBD_CCMD_SELF_TEST 0xAA /* Controller self test */
+#define KBD_CCMD_KBD_TEST 0xAB /* Keyboard interface test */
+#define KBD_CCMD_KBD_DISABLE 0xAD /* Keyboard interface disable */
+#define KBD_CCMD_KBD_ENABLE 0xAE /* Keyboard interface enable */
+#define KBD_CCMD_WRITE_AUX_OBUF 0xD3 /* Write to output buffer as if
+ initiated by the auxiliary device */
+#define KBD_CCMD_WRITE_MOUSE 0xD4 /* Write the following byte to
+ * the mouse */
+
+/*
+ * Keyboard Commands
+ */
+
+#define KBD_CMD_SET_LEDS 0xED /* Set keyboard leds */
+#define KBD_CMD_SET_RATE 0xF3 /* Set typematic rate */
+#define KBD_CMD_ENABLE 0xF4 /* Enable scanning */
+#define KBD_CMD_DISABLE 0xF5 /* Disable scanning */
+#define KBD_CMD_RESET 0xFF /* Reset */
+
+/*
+ * Keyboard Replies
+ */
+
+#define KBD_REPLY_POR 0xAA /* Power on reset */
+#define KBD_REPLY_ACK 0xFA /* Command ACK */
+#define KBD_REPLY_RESEND 0xFE /* Command NACK, send the cmd again */
+
+/*
+ * Status Register Bits
+ */
+
+#define KBD_STAT_OBF 0x01 /* Keyboard output buffer full */
+#define KBD_STAT_IBF 0x02 /* Keyboard input buffer full */
+#define KBD_STAT_SELFTEST 0x04 /* Self test successful */
+#define KBD_STAT_CMD 0x08 /* Last write was a command
+ * write (0=data) */
+#define KBD_STAT_UNLOCKED 0x10 /* Zero if keyboard locked */
+#define KBD_STAT_MOUSE_OBF 0x20 /* Mouse output buffer full */
+#define KBD_STAT_GTO 0x40 /* General receive/xmit timeout */
+#define KBD_STAT_PERR 0x80 /* Parity error */
+
+#define AUX_STAT_OBF (KBD_STAT_OBF | KBD_STAT_MOUSE_OBF)
+
+/*
+ * Controller Mode Register Bits
+ */
+
+#define KBD_MODE_KBD_INT 0x01 /* Keyboard data generate IRQ1 */
+#define KBD_MODE_MOUSE_INT 0x02 /* Mouse data generate IRQ12 */
+#define KBD_MODE_SYS 0x04 /* The system flag (?) */
+#define KBD_MODE_NO_KEYLOCK 0x08 /* The keylock doesn't affect
+ * the keyboard if set */
+#define KBD_MODE_DISABLE_KBD 0x10 /* Disable keyboard interface */
+#define KBD_MODE_DISABLE_MOUSE 0x20 /* Disable mouse interface */
+#define KBD_MODE_KCC 0x40 /* Scan code conversion to PC format */
+#define KBD_MODE_RFU 0x80
+
+/*
+ * Mouse Commands
+ */
+
+#define AUX_SET_RES 0xE8 /* Set resolution */
+#define AUX_SET_SCALE11 0xE6 /* Set 1:1 scaling */
+#define AUX_SET_SCALE21 0xE7 /* Set 2:1 scaling */
+#define AUX_GET_SCALE 0xE9 /* Get scaling factor */
+#define AUX_SET_STREAM 0xEA /* Set stream mode */
+#define AUX_SET_SAMPLE 0xF3 /* Set sample rate */
+#define AUX_ENABLE_DEV 0xF4 /* Enable aux device */
+#define AUX_DISABLE_DEV 0xF5 /* Disable aux device */
+#define AUX_RESET 0xFF /* Reset aux device */
+#define AUX_ACK 0xFA /* Command byte ACK. */
+
+#define AUX_BUF_SIZE 2048 /* This might be better divisible by
+ three to make overruns stay in sync
+ but then the read function would need
+ a lock etc - ick */
+
+struct aux_queue {
+ unsigned long head;
+ unsigned long tail;
+ wait_queue_head_t proc_list;
+ struct fasync_struct *fasync;
+ unsigned char buf[AUX_BUF_SIZE];
+};
+
+
+/* How to access the keyboard macros on this platform. */
+#define kbd_read_input() inb(KBD_DATA_REG)
+#define kbd_read_status() inb(KBD_STATUS_REG)
+#define kbd_write_output(val) outb(val, KBD_DATA_REG)
+#define kbd_write_command(val) outb(val, KBD_CNTL_REG)
diff --git a/drivers/serial/kgdboc.c b/drivers/serial/kgdboc.c
index eadc1ab..ecef6e1 100644
--- a/drivers/serial/kgdboc.c
+++ b/drivers/serial/kgdboc.c
@@ -14,6 +14,7 @@
#include <linux/kernel.h>
#include <linux/ctype.h>
#include <linux/kgdb.h>
+#include <linux/kdb.h>
#include <linux/tty.h>
#define MAX_CONFIG_LEN 40
@@ -32,6 +33,40 @@ static struct kparam_string kps = {
static struct tty_driver *kgdb_tty_driver;
static int kgdb_tty_line;
+#ifdef CONFIG_KDB_KEYBOARD
+static int kgdboc_register_kbd(char **cptr)
+{
+ if (strncmp(*cptr, "kbd", 3) == 0) {
+ if (kdb_poll_idx < KDB_POLL_FUNC_MAX) {
+ kdb_poll_funcs[kdb_poll_idx] = kdb_get_kbd_char;
+ kdb_poll_idx++;
+ if (cptr[0][3] == ',')
+ *cptr += 4;
+ else
+ return 1;
+ }
+ }
+ return 0;
+}
+
+static void kgdboc_unregister_kbd(void)
+{
+ int i;
+
+ for (i = 0; i < kdb_poll_idx; i++) {
+ if (kdb_poll_funcs[i] == kdb_get_kbd_char) {
+ kdb_poll_idx--;
+ kdb_poll_funcs[i] = kdb_poll_funcs[kdb_poll_idx];
+ kdb_poll_funcs[kdb_poll_idx] = NULL;
+ i--;
+ }
+ }
+}
+#else /* ! CONFIG_KDB_KEYBOARD */
+#define kgdboc_register_kbd(x) 0
+#define kgdboc_unregister_kbd()
+#endif /* ! CONFIG_KDB_KEYBOARD */
+
static int kgdboc_option_setup(char *opt)
{
if (strlen(opt) > MAX_CONFIG_LEN) {
@@ -45,25 +80,38 @@ static int kgdboc_option_setup(char *opt)
__setup("kgdboc=", kgdboc_option_setup);
+static void cleanup_kgdboc(void)
+{
+ kgdboc_unregister_kbd();
+ if (configured == 1)
+ kgdb_unregister_io_module(&kgdboc_io_ops);
+}
+
static int configure_kgdboc(void)
{
struct tty_driver *p;
int tty_line = 0;
int err;
+ char *cptr = config;
err = kgdboc_option_setup(config);
if (err || !strlen(config) || isspace(config[0]))
goto noconfig;
err = -ENODEV;
+ kgdb_tty_driver = NULL;
+
+ if (kgdboc_register_kbd(&cptr))
+ goto do_register;
- p = tty_find_polling_driver(config, &tty_line);
+ p = tty_find_polling_driver(cptr, &tty_line);
if (!p)
goto noconfig;
kgdb_tty_driver = p;
kgdb_tty_line = tty_line;
+do_register:
err = kgdb_register_io_module(&kgdboc_io_ops);
if (err)
goto noconfig;
@@ -75,6 +123,7 @@ static int configure_kgdboc(void)
noconfig:
config[0] = 0;
configured = 0;
+ cleanup_kgdboc();
return err;
}
@@ -88,20 +137,18 @@ static int __init init_kgdboc(void)
return configure_kgdboc();
}
-static void cleanup_kgdboc(void)
-{
- if (configured == 1)
- kgdb_unregister_io_module(&kgdboc_io_ops);
-}
-
static int kgdboc_get_char(void)
{
+ if (!kgdb_tty_driver)
+ return -1;
return kgdb_tty_driver->ops->poll_get_char(kgdb_tty_driver,
kgdb_tty_line);
}
static void kgdboc_put_char(u8 chr)
{
+ if (!kgdb_tty_driver)
+ return;
kgdb_tty_driver->ops->poll_put_char(kgdb_tty_driver,
kgdb_tty_line, chr);
}
diff --git a/lib/Kconfig.kgdb b/lib/Kconfig.kgdb
index 02b46de..0fb633c 100644
--- a/lib/Kconfig.kgdb
+++ b/lib/Kconfig.kgdb
@@ -63,4 +63,11 @@ config KGDB_KDB
help
KDB frontend for kernel
+config KDB_KEYBOARD
+ bool "KGDB_KDB: keyboard as input device"
+ depends on VT && KGDB_KDB
+ default y
+ help
+ KDB can use a PS/2 type keyboard for an input device
+
endif # KGDB
--
1.6.4.rc1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists