| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20100224153443.GF13661@kaneng01.tundra.com>
Date: Wed, 24 Feb 2010 10:34:43 -0500
From: Alexandre Bounine <alexb@...dra.com>
To: mporter@...nel.crashing.org
Cc: linux-kernel@...r.kernel.org, linuxppc-dev@...ts.ozlabs.org,
thomas.moll@...go.com, thomas.moll.ext@....com, abounine@....com
Subject: [PATCH 6/7] RapidIO: Add RX/TX enable for SRIO port
From: Thomas Moll <thomas.moll@...go.com>
Add the functionality to enable Input receiver and Output
transmitter of every port, to allow non-maintenance traffic.
Signed-off-by: Thomas Moll <thomas.moll@...go.com>
---
drivers/rapidio/Kconfig | 11 ++++++
drivers/rapidio/rio-scan.c | 79 ++++++++++++++++++++++++++++++++++++++++++++-
include/linux/rio_regs.h | 5 ++
3 files changed, 94 insertions(+), 1 deletion(-)
diff -purN linux-base/drivers/rapidio/Kconfig linux-new/drivers/rapidio/Kconfig
--- linux-base/drivers/rapidio/Kconfig 2010-02-22 10:44:47.000000000 +0100
+++ linux-new/drivers/rapidio/Kconfig 2010-02-22 12:36:20.000000000 +0100
@@ -8,3 +8,14 @@ config RAPIDIO_DISC_TIMEOUT
---help---
Amount of time a discovery node waits for a host to complete
enumeration before giving up.
+
+config RAPIDIO_ENABLE_RX_TX_PORTS
+ bool "Enable RapidIO Input/Output Ports"
+ depends on RAPIDIO
+ ---help---
+ The RapidIO specification describes a Output port transmit
+ enable and a Input port receive enable. The recommended state
+ for Input ports and Output ports should be disabled. When
+ this switch is set the RapidIO subsystem will enable all
+ ports for Input/Output direction to allow other traffic
+ than Maintenance transfers.
diff -purN linux-base/drivers/rapidio/rio-scan.c linux-new/drivers/rapidio/rio-scan.c
--- linux-base/drivers/rapidio/rio-scan.c 2010-02-22 10:48:15.000000000 +0100
+++ linux-new/drivers/rapidio/rio-scan.c 2010-02-22 13:42:08.000000000 +0100
@@ -8,6 +8,10 @@
* Alex Bounine <alexandre.bounine@....com>
* - Added Port-Write/Error Management initialization and handling
*
+ * Copyright 2009 Sysgo AG
+ * Thomas Moll <thomas.moll@...go.com>
+ * - Added Input- Output- enable functionality, to allow full communication
+ *
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
@@ -328,6 +332,65 @@ static int __devinit rio_add_device(stru
}
/**
+ * rio_enable_rx_tx_port - enable input reciever and output transmitter of
+ * given port
+ * @port: Master port associated with the RIO network
+ * @local: local=1 select local port otherwise a far device is reached
+ * @destid: Destination ID of the device to check host bit
+ * @hopcount: Number of hops to reach the target
+ * @port_num: Port (-number on switch) to enable on a far end device
+ *
+ * Returns 0 or 1 from on General Control Command and Status Register
+ * (EXT_PTR+0x3C)
+ */
+inline int rio_enable_rx_tx_port(struct rio_mport *port,
+ int local, u16 destid,
+ u8 hopcount, u8 port_num) {
+#ifdef CONFIG_RAPIDIO_ENABLE_RX_TX_PORTS
+ u32 regval;
+ u32 ext_ftr_ptr;
+
+ /*
+ * enable rx input tx output port
+ */
+ pr_debug("rio_enable_rx_tx_port(local = %d, destid = %d, hopcount = "
+ "%d, port_num = %d)\n", local, destid, hopcount, port_num);
+
+ ext_ftr_ptr = rio_mport_get_physefb(port, local, destid, hopcount);
+
+ if (local) {
+ rio_local_read_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0),
+ ®val);
+ } else {
+ if (rio_mport_read_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), ®val) < 0)
+ return -EIO;
+ }
+
+ if (regval & RIO_PORT_N_CTL_P_TYP_SER) {
+ /* serial */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_SER
+ | RIO_PORT_N_CTL_EN_TX_SER;
+ } else {
+ /* parallel */
+ regval = regval | RIO_PORT_N_CTL_EN_RX_PAR
+ | RIO_PORT_N_CTL_EN_TX_PAR;
+ }
+
+ if (local) {
+ rio_local_write_config_32(port, ext_ftr_ptr +
+ RIO_PORT_N_CTL_CSR(0), regval);
+ } else {
+ if (rio_mport_write_config_32(port, destid, hopcount,
+ ext_ftr_ptr + RIO_PORT_N_CTL_CSR(port_num), regval) < 0)
+ return -EIO;
+ }
+#endif
+ return 0;
+}
+
+/**
* rio_setup_device- Allocates and sets up a RIO device
* @net: RIO network
* @port: Master port to send transactions
@@ -430,9 +493,14 @@ static struct rio_dev __devinit *rio_set
list_add_tail(&rswitch->node, &rio_switches);
- } else
+ } else {
+ if (do_enum)
+ /*Enable Input Output Port (transmitter reviever)*/
+ rio_enable_rx_tx_port(port, 0, destid, hopcount, 0);
+
dev_set_name(&rdev->dev, "%02x:e:%04x", rdev->net->id,
rdev->destid);
+ }
rdev->dev.bus = &rio_bus_type;
@@ -740,6 +808,11 @@ static int __devinit rio_enum_peer(struc
rio_name(rdev), rdev->vid, rdev->did, num_ports);
sw_destid = next_destid;
for (port_num = 0; port_num < num_ports; port_num++) {
+ /*Enable Input Output Port (transmitter reviever)*/
+ rio_enable_rx_tx_port(port, 0,
+ RIO_ANY_DESTID(port->sys_size),
+ hopcount, port_num);
+
if (sw_inport == port_num) {
rdev->rswitch->port_ok |= (1 << port_num);
continue;
@@ -1085,6 +1158,10 @@ int __devinit rio_enum_mport(struct rio_
rc = -ENOMEM;
goto out;
}
+
+ /* Enable Input Output Port (transmitter reviever) */
+ rio_enable_rx_tx_port(mport, 1, 0, 0, 0);
+
if (rio_enum_peer(net, mport, 0) < 0) {
/* A higher priority host won enumeration, bail. */
printk(KERN_INFO
diff -purN linux-base/include/linux/rio_regs.h linux-new/include/linux/rio_regs.h
--- linux-base/include/linux/rio_regs.h 2010-02-22 10:48:15.000000000 +0100
+++ linux-new/include/linux/rio_regs.h 2010-02-22 12:38:57.000000000 +0100
@@ -242,7 +242,12 @@
#define RIO_PORT_N_CTL_PWIDTH 0xc0000000
#define RIO_PORT_N_CTL_PWIDTH_1 0x00000000
#define RIO_PORT_N_CTL_PWIDTH_4 0x40000000
+#define RIO_PORT_N_CTL_P_TYP_SER 0x00000001
#define RIO_PORT_N_CTL_LOCKOUT 0x00000002
+#define RIO_PORT_N_CTL_EN_RX_SER 0x00200000
+#define RIO_PORT_N_CTL_EN_TX_SER 0x00400000
+#define RIO_PORT_N_CTL_EN_RX_PAR 0x08000000
+#define RIO_PORT_N_CTL_EN_TX_PAR 0x40000000
/*
* Error Management Extensions (RapidIO 1.3+, Part 8)
---
Important Notice: This message is intended for the use of the individual to whom it is addressed and may contain information which is privileged, confidential and/or exempt from disclosure under applicable law. If the reader of this message is not the intended recipient, or is not the employee or agent responsible for delivering the message to the intended recipient, you are hereby notified that any dissemination, distribution, or copying of this communication is strictly prohibited. If you have received this communication in error, please notify the sender immediately by telephone or return e-mail and delete the original message from your systems. Thank you.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists