| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20100320170241.55258b0d@neptune.home>
Date: Sat, 20 Mar 2010 17:02:41 +0100
From: Bruno Prémont <bonbons@...ux-vserver.org>
To: Jiri Kosina <jkosina@...e.cz>
Cc: linux-input@...r.kernel.org, linux-usb@...r.kernel.org,
linux-fbdev@...r.kernel.org, linux-kernel@...r.kernel.org,
"Rick L. Vinyard Jr." <rvinyard@...nmsu.edu>,
Nicu Pavel <npavel@...ner.com>,
Oliver Neukum <oliver@...kum.org>,
Jaya Kumar <jayakumar.lkml@...il.com>
Subject: [PATCH v2 1/6] hid: new driver for PicoLCD device
Add basic driver for PicoLCD graphics device.
Initially support keypad with input device, operation mode switching
and provide support for debugging communication via events file from
debugfs.
Signed-off-by: Bruno Prémont <bonbons@...ux-vserver.org>
---
Documentation/ABI/testing/sysfs-driver-hid-picolcd | 17 +
drivers/hid/Kconfig | 18 +
drivers/hid/Makefile | 1 +
drivers/hid/hid-core.c | 2 +
drivers/hid/hid-ids.h | 2 +
drivers/hid/hid-picolcd.c | 1244 ++++++++++++++++++++
6 files changed, 1284 insertions(+), 0 deletions(-)
diff --git a/Documentation/ABI/testing/sysfs-driver-hid-picolcd b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
new file mode 100644
index 0000000..1c63a0f
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-hid-picolcd
@@ -0,0 +1,17 @@
+What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/operation_mode
+Date: March 2010
+Contact: Bruno Prémont <bonbons@...ux-vserver.org>
+Description: Make it possible to switch the PicoLCD device between LCD
+ (firmware) and bootloader (flasher) operation modes.
+
+ Reading: returns list of available modes is show, the active mode
+ being enclosed in brackets ('<' and '>')
+
+ Writing: causes operation mode switch. Permitted values are
+ the non-active mode names listed when read, optionally followed
+ by a delay value expressed in ms.
+
+ Note: when switching mode the current PicoLCD HID device gets
+ disconnected and reconnects after above delay (default value
+ is 5 seconds though this default should not be depended on).
+
diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
index 24d90ea..7097f0a 100644
--- a/drivers/hid/Kconfig
+++ b/drivers/hid/Kconfig
@@ -227,6 +227,24 @@ config HID_PETALYNX
---help---
Support for Petalynx Maxter remote control.
+config HID_PICOLCD
+ tristate "PicoLCD (graphic version)"
+ depends on USB_HID
+ ---help---
+ This provides support for Minibox PicoLCD devices, currently
+ only the graphical ones are supported.
+
+ This includes support for the following device features:
+ - Keypad
+ - Switching between Firmware and Flash mode
+ Features that are not (yet) supported:
+ - Framebuffer for monochrome 256x64 display
+ - Backlight control
+ - Contrast control
+ - IR
+ - General purpose outputs
+ - EEProm / Flash access
+
config HID_SAMSUNG
tristate "Samsung" if EMBEDDED
depends on USB_HID
diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
index 0de2dff..f0a4870 100644
--- a/drivers/hid/Makefile
+++ b/drivers/hid/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_HID_MONTEREY) += hid-monterey.o
obj-$(CONFIG_HID_NTRIG) += hid-ntrig.o
obj-$(CONFIG_HID_PANTHERLORD) += hid-pl.o
obj-$(CONFIG_HID_PETALYNX) += hid-petalynx.o
+obj-$(CONFIG_HID_PICOLCD) += hid-picolcd.o
obj-$(CONFIG_HID_SAMSUNG) += hid-samsung.o
obj-$(CONFIG_HID_SMARTJOYPLUS) += hid-sjoy.o
obj-$(CONFIG_HID_SONY) += hid-sony.o
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index a50d850..2bd0671 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -1330,6 +1330,8 @@ static const struct hid_device_id hid_blacklist[] = {
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_RUMBLEPAD2) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACETRAVELLER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_SPACENAVIGATOR) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_SIDEWINDER_GV) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_NE4K) },
{ HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_LK6K) },
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index 010368e..6d67582 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -330,6 +330,8 @@
#define USB_VENDOR_ID_MICROCHIP 0x04d8
#define USB_DEVICE_ID_PICKIT1 0x0032
#define USB_DEVICE_ID_PICKIT2 0x0033
+#define USB_DEVICE_ID_PICOLCD 0xc002
+#define USB_DEVICE_ID_PICOLCD_BOOTLOADER 0xf002
#define USB_VENDOR_ID_MICROSOFT 0x045e
#define USB_DEVICE_ID_SIDEWINDER_GV 0x003b
diff --git a/drivers/hid/hid-picolcd.c b/drivers/hid/hid-picolcd.c
new file mode 100644
index 0000000..30b8e08
--- /dev/null
+++ b/drivers/hid/hid-picolcd.c
@@ -0,0 +1,1244 @@
+/***************************************************************************
+ * Copyright (C) 2010 by Bruno Prémont <bonbons@...ux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@...nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+
+#define PICOLCD_NAME "PicoLCD (graphic)"
+
+/* Report numbers */
+#define REPORT_ERROR_CODE 0x10 /* LCD: IN[16] */
+#define ERR_SUCCESS 0x00
+#define ERR_PARAMETER_MISSING 0x01
+#define ERR_DATA_MISSING 0x02
+#define ERR_BLOCK_READ_ONLY 0x03
+#define ERR_BLOCK_NOT_ERASABLE 0x04
+#define ERR_BLOCK_TOO_BIG 0x05
+#define ERR_SECTION_OVERFLOW 0x06
+#define ERR_INVALID_CMD_LEN 0x07
+#define ERR_INVALID_DATA_LEN 0x08
+#define REPORT_KEY_STATE 0x11 /* LCD: IN[2] */
+#define REPORT_IR_DATA 0x21 /* LCD: IN[63] */
+#define REPORT_EE_DATA 0x32 /* LCD: IN[63] */
+#define REPORT_MEMORY 0x41 /* LCD: IN[63] */
+#define REPORT_LED_STATE 0x81 /* LCD: OUT[1] */
+#define REPORT_BRIGHTNESS 0x91 /* LCD: OUT[1] */
+#define REPORT_CONTRAST 0x92 /* LCD: OUT[1] */
+#define REPORT_RESET 0x93 /* LCD: OUT[2] */
+#define REPORT_LCD_CMD 0x94 /* LCD: OUT[63] */
+#define REPORT_LCD_DATA 0x95 /* LCD: OUT[63] */
+#define REPORT_LCD_CMD_DATA 0x96 /* LCD: OUT[63] */
+#define REPORT_EE_READ 0xa3 /* LCD: OUT[63] */
+#define REPORT_EE_WRITE 0xa4 /* LCD: OUT[63] */
+#define REPORT_ERASE_MEMORY 0xb2 /* LCD: OUT[2] */
+#define REPORT_READ_MEMORY 0xb3 /* LCD: OUT[3] */
+#define REPORT_WRITE_MEMORY 0xb4 /* LCD: OUT[63] */
+#define REPORT_SPLASH_RESTART 0xc1 /* LCD: OUT[1] */
+#define REPORT_EXIT_KEYBOARD 0xef /* LCD: OUT[2] */
+#define REPORT_VERSION 0xf1 /* LCD: IN[2],OUT[1] Bootloader: IN[2],OUT[1] */
+#define REPORT_BL_ERASE_MEMORY 0xf2 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_READ_MEMORY 0xf3 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_WRITE_MEMORY 0xf4 /* Bootloader: IN[36],OUT[36] */
+#define REPORT_DEVID 0xf5 /* LCD: IN[5], OUT[1] Bootloader: IN[5],OUT[1] */
+#define REPORT_SPLASH_SIZE 0xf6 /* LCD: IN[4], OUT[1] */
+#define REPORT_HOOK_VERSION 0xf7 /* LCD: IN[2], OUT[1] */
+#define REPORT_EXIT_FLASHER 0xff /* Bootloader: OUT[2] */
+
+/* Input device
+ *
+ * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys
+ * and header for 4x4 key matrix. The built-in keys are part of the matrix.
+ */
+#define PICOLCD_KEYS 17
+
+static const int def_keymap[PICOLCD_KEYS] = {
+ KEY_RESERVED, /* none */
+ KEY_BACK, /* col 4 + row 1 */
+ KEY_HOMEPAGE, /* col 3 + row 1 */
+ KEY_RESERVED, /* col 2 + row 1 */
+ KEY_RESERVED, /* col 1 + row 1 */
+ KEY_SCROLLUP, /* col 4 + row 2 */
+ KEY_OK, /* col 3 + row 2 */
+ KEY_SCROLLDOWN, /* col 2 + row 2 */
+ KEY_RESERVED, /* col 1 + row 2 */
+ KEY_RESERVED, /* col 4 + row 3 */
+ KEY_RESERVED, /* col 3 + row 3 */
+ KEY_RESERVED, /* col 2 + row 3 */
+ KEY_RESERVED, /* col 1 + row 3 */
+ KEY_RESERVED, /* col 4 + row 4 */
+ KEY_RESERVED, /* col 3 + row 4 */
+ KEY_RESERVED, /* col 2 + row 4 */
+ KEY_RESERVED, /* col 1 + row 4 */
+};
+
+/* Description of in-progress IO operation, used for operations
+ * that trigger response from device */
+struct picolcd_pending {
+ struct hid_report *out_report;
+ struct hid_report *in_report;
+ int raw_size;
+ u8 raw_data[64];
+};
+
+/* Per device data structure */
+struct picolcd_data {
+ struct hid_device *hdev;
+#ifdef CONFIG_DEBUG_FS
+ int addr_sz;
+#endif
+ u8 version[2];
+ /* input stuff */
+ u8 pressed_keys[2];
+ struct input_dev *input_keys;
+ struct input_dev *input_cir;
+ int keycode[PICOLCD_KEYS];
+
+ /* Housekeeping stuff */
+ spinlock_t lock;
+ struct picolcd_pending *pending;
+ struct completion ready;
+ int status;
+#define PICOLCD_BUSY 1
+#define PICOLCD_FAILED 4
+#define PICOLCD_BOOTLOADER 8
+};
+
+
+/* Find a given report */
+#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT)
+#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT)
+
+static struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir)
+{
+ struct list_head *feature_report_list = &hdev->report_enum[dir].report_list;
+ struct hid_report *report = NULL;
+
+ list_for_each_entry(report, feature_report_list, list) {
+ if (report->id == id)
+ return report;
+ }
+ dev_warn(&hdev->dev, "No report with id 0x%x found\n", id);
+ return NULL;
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report);
+#define usbhid_submit_report(a, b, c) \
+ picolcd_debug_out_report(hid_get_drvdata(a), a, b); \
+ usbhid_submit_report(a, b, c)
+#endif
+
+/* Submit a report and wait for a reply from device - if device fades away
+ * or does not respond in time, return NULL */
+static struct picolcd_pending* picolcd_send_and_wait(struct hid_device *hdev,
+ int report_id, const u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct picolcd_pending *work;
+ struct hid_report *report = picolcd_out_report(report_id, hdev);
+ unsigned long flags;
+ int status, i, j, k;
+
+ if (!report)
+ return NULL;
+ work = kzalloc(sizeof(*work), GFP_KERNEL);
+ if (!work)
+ return NULL;
+
+ work->out_report = report;
+ work->in_report = NULL;
+ work->raw_size = 0;
+
+retry:
+ /* try to get lock and enqueue our job */
+ spin_lock_irqsave(&data->lock, flags);
+ status = data->status;
+ if (data->pending || (status & PICOLCD_FAILED)) {
+ /* some job already pending,
+ * wait for it to complete and try again */
+ spin_unlock_irqrestore(&data->lock, flags);
+ if (status & PICOLCD_FAILED) {
+ kfree(work);
+ return NULL;
+ }
+ wait_for_completion_interruptible_timeout(&data->ready, HZ*2);
+ goto retry;
+ }
+ data->status |= PICOLCD_BUSY;
+ data->pending = work;
+ for (i = k = 0; i < report->maxfield; i++)
+ for (j = 0; j < report->field[i]->report_count; j++) {
+ hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0);
+ k++;
+ }
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ complete_all(&data->ready);
+ INIT_COMPLETION(data->ready);
+ spin_unlock_irqrestore(&data->lock, flags);
+ /* wait for our job to complete */
+ wait_for_completion_interruptible_timeout(&data->ready, HZ*2);
+
+ spin_lock_irqsave(&data->lock, flags);
+ if (data->pending == work) {
+ data->status &= ~PICOLCD_BUSY;
+ data->pending = NULL;
+ complete_all(&data->ready);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return work;
+ } else {
+ spin_unlock_irqrestore(&data->lock, flags);
+ kfree(work);
+ return NULL;
+ }
+}
+
+/*
+ * input class device
+ */
+static int picolcd_raw_keypad(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /*
+ * Keypad event
+ * First and second data bytes list currently pressed keys,
+ * 0x00 means no key and at most 2 keys may be pressed at same time
+ */
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ int i, j;
+
+ /* determine newly pressed keys */
+ for (i = 0; i < size; i++) {
+ int key_code;
+ if (raw_data[i] == 0)
+ continue;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_already_down;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == 0) {
+ data->pressed_keys[j] = raw_data[i];
+ break;
+ }
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]);
+ if (input_get_keycode(data->input_keys, raw_data[i], &key_code))
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key press for %u:%d", raw_data[i], key_code);
+ input_report_key(data->input_keys, key_code, 1);
+ }
+ input_sync(data->input_keys);
+key_already_down:
+ continue;
+ }
+
+ /* determine newly released keys */
+ for (j = 0; j < sizeof(data->pressed_keys); j++) {
+ int key_code;
+ if (data->pressed_keys[j] == 0)
+ continue;
+ for (i = 0; i < size; i++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_still_down;
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]);
+ if (input_get_keycode(data->input_keys, data->pressed_keys[j], &key_code))
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key release for %u:%d", data->pressed_keys[j], key_code);
+ input_report_key(data->input_keys, key_code, 0);
+ }
+ input_sync(data->input_keys);
+ data->pressed_keys[j] = 0;
+key_still_down:
+ continue;
+ }
+ return 1;
+}
+
+static int picolcd_raw_cir(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /* Need understanding of CIR data format to implement ... */
+ return 1;
+}
+
+
+
+/*
+ * Reset our device and wait for answer to VERSION request
+ */
+static int picolcd_reset(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev);
+ struct picolcd_pending *verinfo;
+ unsigned long flags;
+
+ if (!data || !report || report->maxfield != 1)
+ return -ENODEV;
+
+ spin_lock_irqsave(&data->lock, flags);
+ complete_all(&data->ready);
+ INIT_COMPLETION(data->ready);
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+
+ /* perform the reset */
+ hid_set_field(report->field[0], 0, 1);
+ usbhid_submit_report(hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (verinfo && verinfo->raw_size == 2) {
+ if (data->status & PICOLCD_BOOTLOADER) {
+ dev_info(&hdev->dev, "PicoLCD reset successful, bootloader version %d.%d\n",
+ verinfo->raw_data[0], verinfo->raw_data[1]);
+ data->version[0] = verinfo->raw_data[0];
+ data->version[1] = verinfo->raw_data[1];
+ } else {
+ dev_info(&hdev->dev, "PicoLCD reset successful, firmware version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ }
+ kfree(verinfo);
+ verinfo = NULL;
+ } else if (verinfo) {
+ dev_err(&hdev->dev, "confused, got unexpected version response from PicoLCD after reset\n");
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "no version response from PicoLCD after reset");
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+/*
+ * The "operation_mode" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ return snprintf(buf, PAGE_SIZE, "<bootloader> lcd\n");
+ else
+ return snprintf(buf, PAGE_SIZE, "bootloader <lcd>\n");
+}
+
+static ssize_t picolcd_operation_mode_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ struct hid_report *report = NULL;
+ size_t cnt = count;
+ int timeout = 5000;
+ unsigned u;
+ unsigned long flags;
+
+ if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) {
+ if (data->status & PICOLCD_BOOTLOADER)
+ report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev);
+ buf += 3;
+ cnt -= 3;
+ } else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) {
+ if (!(data->status & PICOLCD_BOOTLOADER))
+ report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev);
+ buf += 10;
+ cnt -= 10;
+ }
+ if (!report)
+ return -EINVAL;
+
+ while (cnt > 0 && (*buf == ' ' || *buf == '\t')) {
+ buf++;
+ cnt--;
+ }
+ while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r'))
+ cnt--;
+ if (cnt > 0) {
+ if (sscanf(buf, "%u", &u) != 1)
+ return -EINVAL;
+ if (u > 30000)
+ return -EINVAL;
+ else
+ timeout = u;
+ }
+
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, timeout & 0xff);
+ hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return count;
+}
+
+static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show,
+ picolcd_operation_mode_store);
+
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * Helper code for HID report level dumping/debugging
+ */
+static const char *error_codes[] = {
+ "success", "parameter missing", "data_missing", "block readonly", "block not erasable",
+ "block too big", "section overflow", "invalid command length", "invalid data length",
+};
+
+static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data,
+ const size_t data_len)
+{
+ int i, j;
+ for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) {
+ dst[j++] = hex_asc[(data[i] >> 4) & 0x0f];
+ dst[j++] = hex_asc[data[i] & 0x0f];
+ dst[j++] = ' ';
+ }
+ if (j < dst_sz) {
+ dst[j--] = '\0';
+ dst[j] = '\n';
+ } else
+ dst[j] = '\0';
+}
+
+static void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report)
+{
+ u8 raw_data[70];
+ int raw_size = (report->size >> 3) + 1;
+ char *buff;
+#define BUFF_SZ 256
+
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ snprintf(buff, BUFF_SZ, "\nout report %d (size %d) = ",
+ report->id, raw_size);
+ hid_debug_event(hdev, buff);
+ if (raw_size + 5 > sizeof(raw_data)) {
+ hid_debug_event(hdev, " TOO BIG\n");
+ return;
+ } else {
+ raw_data[0] = report->id;
+ hid_output_report(report, raw_data);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size);
+ hid_debug_event(hdev, buff);
+ }
+
+ switch (report->id) {
+ case REPORT_LED_STATE:
+ /* 1 data byte with GPO state */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LED_STATE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BRIGHTNESS:
+ /* 1 data byte with brightness */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_BRIGHTNESS", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_CONTRAST:
+ /* 1 data byte with contrast */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_CONTRAST", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_RESET:
+ /* 2 data bytes with reset duration in ms */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_RESET", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n",
+ raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD:
+ /* 63 data bytes with LCD commands */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO: format decoding */
+ break;
+ case REPORT_LCD_DATA:
+ /* 63 data bytes with LCD data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD_DATA:
+ /* 63 data bytes with LCD commands and data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_READ:
+ /* 3 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_READ", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_WRITE:
+ /* 3+1..20 data bytes with write area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_WRITE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_ERASE_MEMORY:
+ case REPORT_BL_ERASE_MEMORY:
+ /* 3 data bytes with pointer inside erase block */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_ERASE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_READ_MEMORY:
+ case REPORT_BL_READ_MEMORY:
+ /* 4 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_READ_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_WRITE_MEMORY:
+ case REPORT_BL_WRITE_MEMORY:
+ /* 4+1..32 data bytes with write adrea description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_WRITE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_RESTART:
+ /* TODO */
+ break;
+ case REPORT_EXIT_KEYBOARD:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EXIT_KEYBOARD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EXIT_FLASHER:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "<unknown>", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+
+static inline void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size)
+{
+ char *buff;
+
+#define BUFF_SZ 256
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ switch (report->id) {
+ case REPORT_ERROR_CODE:
+ /* 2 data bytes with affected report and error code */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_ERROR_CODE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[2] < ARRAY_SIZE(error_codes))
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n",
+ raw_data[2], error_codes[raw_data[2]], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_KEY_STATE:
+ /* 2 data bytes with key state */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_KEY_STATE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0)
+ snprintf(buff, BUFF_SZ, "\tNo key pressed\n");
+ else if (raw_data[2] == 0)
+ snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n",
+ raw_data[1], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n",
+ raw_data[1], raw_data[1], raw_data[2], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_IR_DATA:
+ /* Up to 20 byes of IR scancode data */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_IR_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0) {
+ snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[1] + 1 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_EE_DATA:
+ /* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_EE_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n", raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_MEMORY:
+ /* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BL_ERASE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_ERASE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_READ_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_READ_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_WRITE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_WRITE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n",
+ raw_data[1], raw_data[2], raw_data[3], raw_data[4]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n",
+ raw_data[5]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n",
+ (raw_data[2] << 8) | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n",
+ (raw_data[4] << 8) | raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[1], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "<unknown>", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+#else
+#define picolcd_debug_raw_event(data, hdev, report, raw_data, size)
+#endif
+
+/*
+ * Handle raw report as sent by device
+ */
+static int picolcd_raw_event(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+ int ret = 0;
+
+ if (data == NULL)
+ return 1;
+
+ if (report->id == REPORT_KEY_STATE) {
+ if (data->input_keys)
+ ret = picolcd_raw_keypad(hdev, report, raw_data+1, size-1);
+ } else if (report->id == REPORT_IR_DATA) {
+ if (data->input_cir)
+ ret = picolcd_raw_cir(hdev, report, raw_data+1, size-1);
+ } else {
+ spin_lock_irqsave(&data->lock, flags);
+ /*
+ * We let the caller of picolcd_send_and_wait() check if the report
+ * we got is one of the expected ones or not.
+ */
+ if (data->pending) {
+ memcpy(data->pending->raw_data, raw_data+1, size-1);
+ data->pending->raw_size = size-1;
+ data->pending->in_report = report;
+ complete_all(&data->ready);
+ }
+ spin_unlock_irqrestore(&data->lock, flags);
+ }
+
+ picolcd_debug_raw_event(data, hdev, report, raw_data, size);
+ return 1;
+}
+
+#ifdef CONFIG_PM
+static int picolcd_suspend(struct hid_device *hdev)
+{
+ dbg_hid(PICOLCD_NAME " device ready for suspend\n");
+ return 0;
+}
+
+static int picolcd_resume(struct hid_device *hdev)
+{
+ return 0;
+}
+
+static int picolcd_reset_resume(struct hid_device *hdev)
+{
+ int ret;
+ ret = picolcd_reset(hdev);
+ if (ret)
+ dbg_hid(PICOLCD_NAME " resetting our device failed: %d\n", ret);
+ return 0;
+}
+#endif
+
+/* initialize keypad input device */
+static inline int picolcd_init_keys(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ struct hid_device *hdev = data->hdev;
+ struct input_dev *idev;
+ int error, i;
+
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 2 ||
+ report->field[0]->report_size != 8) {
+ dev_err(&hdev->dev, "unsupported KEY_STATE report");
+ return -EINVAL;
+ }
+
+ idev = input_allocate_device();
+ if (idev == NULL) {
+ dev_err(&hdev->dev, "failed to allocate input device");
+ return -ENOMEM;
+ }
+ input_set_drvdata(idev, hdev);
+ memcpy(data->keycode, def_keymap, sizeof(def_keymap));
+ idev->name = hdev->name;
+ idev->phys = hdev->phys;
+ idev->uniq = hdev->uniq;
+ idev->id.bustype = hdev->bus;
+ idev->id.vendor = hdev->vendor;
+ idev->id.product = hdev->product;
+ idev->id.version = hdev->version;
+ idev->dev.parent = hdev->dev.parent;
+ idev->keycode = &data->keycode;
+ idev->keycodemax = PICOLCD_KEYS;
+ idev->keycodesize = sizeof(int);
+ input_set_capability(idev, EV_MSC, MSC_SCAN);
+ set_bit(EV_REP, idev->evbit);
+ for (i = 0; i < PICOLCD_KEYS; i++) {
+ int key = ((int *)idev->keycode)[i];
+ if (key < KEY_MAX && key >= 0)
+ input_set_capability(idev, EV_KEY, key);
+ }
+ error = input_register_device(idev);
+ if (error) {
+ dev_err(&hdev->dev, "error registering the input device");
+ input_free_device(idev);
+ return error;
+ }
+ data->input_keys = idev;
+ return 0;
+}
+
+static void picolcd_exit_keys(struct picolcd_data *data)
+{
+ struct input_dev *idev = data->input_keys;
+
+ data->input_keys = NULL;
+ if (idev)
+ input_unregister_device(idev);
+}
+
+/* initialize CIR input device */
+static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+ /* support not implemented yet */
+ return 0;
+}
+
+static void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+
+static inline int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data)
+{
+ struct picolcd_pending *verinfo;
+ struct hid_report *report;
+ int error;
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (!verinfo || !verinfo->in_report) {
+ kfree(verinfo);
+ dev_err(&hdev->dev, "failed to query FW version of device\n");
+ return -ENODEV;
+ } else if (verinfo->in_report->id == REPORT_VERSION && verinfo->raw_size == 2) {
+ dev_info(&hdev->dev, "detected PicoLCD with firmware version %d.%d\n",
+ verinfo->raw_data[0], verinfo->raw_data[1]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ if (data->version[0] != 0 && data->version[1] != 3)
+ dev_info(&hdev->dev, "Device with untested firmware revision, "
+ "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "unexpected version response from PicoLCD"
+ " (report=0x%02x, size=%d)\n",
+ verinfo->in_report->id, verinfo->raw_size);
+ kfree(verinfo);
+ verinfo = NULL;
+ return -ENODEV;
+ }
+
+ /* Setup keypad input device */
+ error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev));
+ if (error)
+ goto err;
+
+ /* Setup CIR input device */
+ error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev));
+ if (error)
+ goto err;
+
+#ifdef CONFIG_DEBUG_FS
+ report = picolcd_out_report(REPORT_READ_MEMORY, hdev);
+ if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+ data->addr_sz = report->field[0]->report_count - 1;
+ else
+ data->addr_sz = -1;
+#endif
+ return 0;
+err:
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+ return error;
+}
+
+static inline int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data)
+{
+ struct picolcd_pending *verinfo;
+ struct hid_report *report;
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (!verinfo || !verinfo->in_report) {
+ kfree(verinfo);
+ dev_err(&hdev->dev, "failed to query FW version of device\n");
+ return -ENODEV;
+ } else if (verinfo->in_report->id == REPORT_VERSION && verinfo->raw_size == 2) {
+ dev_info(&hdev->dev, "detected PicoLCD with bootloader version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ if (data->version[0] != 1 && data->version[1] != 0)
+ dev_info(&hdev->dev, "Device with untested bootloader revision, "
+ "please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+ kfree(verinfo);
+ verinfo = NULL;
+ } else {
+ dev_err(&hdev->dev, "unexpected version response from PicoLCD"
+ " (report=0x%02x, size=%d)\n",
+ verinfo->in_report->id, verinfo->raw_size);
+ kfree(verinfo);
+ verinfo = NULL;
+ return -ENODEV;
+ }
+
+#ifdef CONFIG_DEBUG_FS
+ report = picolcd_out_report(REPORT_BL_READ_MEMORY, hdev);
+ if (report && report->maxfield == 1 && report->field[0]->report_size == 8)
+ data->addr_sz = report->field[0]->report_count - 1;
+ else
+ data->addr_sz = -1;
+#endif
+ return 0;
+}
+
+static int picolcd_probe(struct hid_device *hdev,
+ const struct hid_device_id *id)
+{
+ struct picolcd_data *data;
+ int error = -ENOMEM;
+
+ dbg_hid(PICOLCD_NAME " hardware probe...\n");
+
+ /*
+ * Let's allocate the picolcd data structure, set some reasonable
+ * defaults, and associate it with the device
+ */
+ data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL);
+ if (data == NULL) {
+ dev_err(&hdev->dev, "can't allocate space for Minibox PicoLCD device data\n");
+ error = -ENOMEM;
+ goto err_no_cleanup;
+ }
+
+ spin_lock_init(&data->lock);
+ init_completion(&data->ready);
+ data->hdev = hdev;
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+ hid_set_drvdata(hdev, data);
+
+ /* Parse the device reports and start it up */
+ error = hid_parse(hdev);
+ if (error) {
+ dev_err(&hdev->dev, "device report parse failed\n");
+ goto err_cleanup_data;
+ }
+
+ /* We don't use hidinput but hid_hw_start() fails if nothing is
+ * claimed. So spoof claimed input. */
+ hdev->claimed = HID_CLAIMED_INPUT;
+ error = hid_hw_start(hdev, 0);
+ hdev->claimed = 0;
+ if (error) {
+ dev_err(&hdev->dev, "hardware start failed\n");
+ goto err_cleanup_data;
+ }
+
+ error = hdev->ll_driver->open(hdev);
+ if (error) {
+ dev_err(&hdev->dev, "failed to open input interrupt pipe for key and IR events\n");
+ goto err_cleanup_hid_hw;
+ }
+
+ error = sysfs_create_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+ if (error) {
+ dev_err(&hdev->dev, "failed to create sysfs attributes\n");
+ goto err_cleanup_hid_ll;
+ }
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ error = picolcd_probe_bootloader(hdev, data);
+ else
+ error = picolcd_probe_lcd(hdev, data);
+ if (error)
+ goto err_cleanup_sysfs;
+
+ dbg_hid(PICOLCD_NAME " activated and initialized\n");
+ return 0;
+
+err_cleanup_sysfs:
+ sysfs_remove_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+err_cleanup_hid_ll:
+ hdev->ll_driver->close(hdev);
+err_cleanup_hid_hw:
+ hid_hw_stop(hdev);
+err_cleanup_data:
+ kfree(data);
+err_no_cleanup:
+ hid_set_drvdata(hdev, NULL);
+
+ return error;
+}
+
+static void picolcd_remove(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+
+ dbg_hid(PICOLCD_NAME " hardware remove...\n");
+ spin_lock_irqsave(&data->lock, flags);
+ data->status |= PICOLCD_FAILED;
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ sysfs_remove_file(&(hdev->dev.kobj), &dev_attr_operation_mode.attr);
+ hdev->ll_driver->close(hdev);
+ hid_hw_stop(hdev);
+
+ /* Cleanup input */
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+
+ /* Finally, clean up the picolcd data itself */
+ kfree(data);
+}
+
+static const struct hid_device_id picolcd_devices[] = {
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
+ { }
+};
+MODULE_DEVICE_TABLE(hid, picolcd_devices);
+
+static struct hid_driver picolcd_driver = {
+ .name = "hid-picolcd",
+ .id_table = picolcd_devices,
+ .probe = picolcd_probe,
+ .remove = picolcd_remove,
+ .raw_event = picolcd_raw_event,
+#ifdef CONFIG_PM
+ .suspend = picolcd_suspend,
+ .resume = picolcd_resume,
+ .reset_resume = picolcd_reset_resume,
+#endif
+};
+
+static int __init picolcd_init(void)
+{
+ return hid_register_driver(&picolcd_driver);
+}
+
+static void __exit picolcd_exit(void)
+{
+ hid_unregister_driver(&picolcd_driver);
+}
+
+module_init(picolcd_init);
+module_exit(picolcd_exit);
+MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver");
+MODULE_LICENSE("GPL v2");
--
1.6.4.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists