| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <4CD2DDC6020000780002098C@vpn.id2.novell.com>
Date: Thu, 04 Nov 2010 15:22:30 +0000
From: "Jan Beulich" <JBeulich@...ell.com>
To: <mingo@...e.hu>, <tglx@...utronix.de>, <hpa@...or.com>
Cc: "Yinghai Lu" <yinghai@...nel.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH] x86-64: fix and clean up AMD Fam10 MMCONF enabling
Candidate memory ranges were not calculated properly (start addresses
got needlessly rounded down, and end addresses didn't get rounded up
at all), address comparison for secondary CPUs was done on only part
of the address, and disabled status wasn't tracked properly.
Signed-off-by: Jan Beulich <jbeulich@...ell.com>
Cc: Yinghai Lu <yinghai@...nel.org>
---
arch/x86/kernel/mmconf-fam10h_64.c | 54 +++++++++++++++++--------------------
1 file changed, 25 insertions(+), 29 deletions(-)
--- linux-2.6.37-rc1/arch/x86/kernel/mmconf-fam10h_64.c
+++ 2.6.37-rc1-x86_64-mmconf-fam10h/arch/x86/kernel/mmconf-fam10h_64.c
@@ -25,7 +25,6 @@ struct pci_hostbridge_probe {
};
static u64 __cpuinitdata fam10h_pci_mmconf_base;
-static int __cpuinitdata fam10h_pci_mmconf_base_status;
static struct pci_hostbridge_probe pci_probes[] __cpuinitdata = {
{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
@@ -44,7 +43,9 @@ static int __cpuinit cmp_range(const voi
return start1 - start2;
}
-/*[47:0] */
+#define UNIT (1ULL << (5 + 3 + 12))
+#define MASK (~(UNIT - 1))
+#define SIZE (UNIT << 8)
/* need to avoid (0xfd<<32) and (0xfe<<32), ht used space */
#define FAM10H_PCI_MMCONF_BASE (0xfcULL<<32)
#define BASE_VALID(b) ((b != (0xfdULL << 32)) && (b != (0xfeULL << 32)))
@@ -64,12 +65,11 @@ static void __cpuinit get_fam10h_pci_mmc
struct range range[8];
/* only try to get setting from BSP */
- /* -1 or 1 */
- if (fam10h_pci_mmconf_base_status)
+ if (fam10h_pci_mmconf_base)
return;
if (!early_pci_allowed())
- goto fail;
+ return;
found = 0;
for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
@@ -91,7 +91,7 @@ static void __cpuinit get_fam10h_pci_mmc
}
if (!found)
- goto fail;
+ return;
/* SYS_CFG */
address = MSR_K8_SYSCFG;
@@ -104,11 +104,11 @@ static void __cpuinit get_fam10h_pci_mmc
/* TOP_MEM2 */
address = MSR_K8_TOP_MEM2;
rdmsrl(address, val);
- tom2 = val & (0xffffULL<<32);
+ tom2 = val & 0xffffff800000ULL;
}
if (base <= tom2)
- base = tom2 + (1ULL<<32);
+ base = (tom2 + 2 * UNIT - 1) & MASK;
/*
* need to check if the range is in the high mmio range that is
@@ -123,9 +123,9 @@ static void __cpuinit get_fam10h_pci_mmc
if (!(reg & 3))
continue;
- start = (((u64)reg) << 8) & (0xffULL << 32); /* 39:16 on 31:8*/
+ start = (u64)(reg & 0xffffff00) << 8; /* 39:16 on 31:8*/
reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
- end = (((u64)reg) << 8) & (0xffULL << 32); /* 39:16 on 31:8*/
+ end = ((u64)(reg & 0xffffff00) << 8) | 0xffff; /* 39:16 on 31:8*/
if (!end)
continue;
@@ -143,32 +143,27 @@ static void __cpuinit get_fam10h_pci_mmc
if (range[hi_mmio_num - 1].end < base)
goto out;
- if (range[0].start > base)
+ if (range[0].start > base + SIZE)
goto out;
/* need to find one window */
- base = range[0].start - (1ULL << 32);
+ base = (range[0].start & MASK) - UNIT;
if ((base > tom2) && BASE_VALID(base))
goto out;
- base = range[hi_mmio_num - 1].end + (1ULL << 32);
+ base = (range[hi_mmio_num - 1].end + UNIT) & MASK;
if ((base > tom2) && BASE_VALID(base))
goto out;
/* need to find window between ranges */
- if (hi_mmio_num > 1)
- for (i = 0; i < hi_mmio_num - 1; i++) {
- if (range[i + 1].start > (range[i].end + (1ULL << 32))) {
- base = range[i].end + (1ULL << 32);
- if ((base > tom2) && BASE_VALID(base))
- goto out;
- }
+ for (i = 1; i < hi_mmio_num; i++) {
+ base = (range[i - 1].end + UNIT) & MASK;
+ val = range[i].start & MASK;
+ if (val >= base + SIZE && base > tom2 && BASE_VALID(base))
+ goto out;
}
-
-fail:
- fam10h_pci_mmconf_base_status = -1;
return;
+
out:
fam10h_pci_mmconf_base = base;
- fam10h_pci_mmconf_base_status = 1;
}
void __cpuinit fam10h_check_enable_mmcfg(void)
@@ -190,11 +185,10 @@ void __cpuinit fam10h_check_enable_mmcfg
/* only trust the one handle 256 buses, if acpi=off */
if (!acpi_pci_disabled || busnbits >= 8) {
- u64 base;
- base = val & (0xffffULL << 32);
- if (fam10h_pci_mmconf_base_status <= 0) {
+ u64 base = val & MASK;
+
+ if (!fam10h_pci_mmconf_base) {
fam10h_pci_mmconf_base = base;
- fam10h_pci_mmconf_base_status = 1;
return;
} else if (fam10h_pci_mmconf_base == base)
return;
@@ -206,8 +200,10 @@ void __cpuinit fam10h_check_enable_mmcfg
* with 256 buses
*/
get_fam10h_pci_mmconf_base();
- if (fam10h_pci_mmconf_base_status <= 0)
+ if (!fam10h_pci_mmconf_base) {
+ pci_probe &= ~PCI_CHECK_ENABLE_AMD_MMCONF;
return;
+ }
printk(KERN_INFO "Enable MMCONFIG on AMD Family 10h\n");
val &= ~((FAM10H_MMIO_CONF_BASE_MASK<<FAM10H_MMIO_CONF_BASE_SHIFT) |
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists