| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-id: <4D06B1F7.3080308@samsung.com>
Date: Tue, 14 Dec 2010 08:53:27 +0900
From: Jaehoon Chung <jh80.chung@...sung.com>
To: Philip Rakity <prakity@...vell.com>
Cc: "linux-mmc@...r.kernel.org" <linux-mmc@...r.kernel.org>,
"linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
Chris Ball <cjb@...top.org>, Tejun Heo <tj@...nel.org>
Subject: Re: [BUG]: mmc: single thread workqueue very bad - breaks multiple
PERMANENT CARDS
Hi Philip.
I known that have kernel parameter.."rootwait"
Did you use "rootwait" or "rootdelay"?
I also need information about this problem..
Philip Rakity wrote:
> Needed to change in drivers/mmc/core
>
>> create_singlethread_workqueue
> to
> create_workqueue
>
> to make multiple cards be detected at boot time.
>
> Logs with traces (not working and working) below.
>
> This could be a bug in the mmc layer or in the workqueue code.
>
> reposting to linux-list and linux-mmc for additional comments
>
>>
>> I am trying to boot
>>
>> I have an external SD card.
>>
>> I have a PERMANENT eMMC card on the board. (BROKEN_CARD_DETECT set and POLLING OFF)
>> I have a PERMANENT sdio card on the board (BROKEN_CARD_DETECT set and POLLING OFF)
>> I am trying to boot from the eMMC.
>>
>> in the arch directory if I init the SD controller first -- booting fails
>> if I init the eMMC SD booting works
>>
>> From the trace so far it looks like I cannot have 2 entries on the the workqueue for mmc_rescan.
>>
>> The sdhci driver sees 2 permanent slots and calls up to the mmc layer to handle initial card detect.
>>
>> I think the workqueue needs to check if work is pending and reschedule itself -- not sure how to do this.
>>
>> mmc_rescan is not being called -- any ideas ?
>>
>> trace below
>>
>> max8925-rtc max8925-rtc: rtc core: registered max8925-rtc as rtc0
>> [ 89.784231] sdhci: Secure Digital Host Controller Interface driver
>> [ 89.802610] sdhci: Copyright(c) Pierre Ossman
>> [ 89.815573] mmc0: no vmmc regulator found
>> [ 89.827627] mmc_start_host:mmc0: ENTER
>> [ 89.838892] mmc_detect_change: mmc0: ENTER
>> [ 89.851084] mmc_schedule_delayed_work: ENTER
>> [ 89.863893] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 89.877922] mmc_rescan:mmc0: ENTER
>> [ 89.888025] mmc0: mmc_rescan: trying to init card at 400000 Hz
>> [ 89.905442] mmc_detect_change: mmc0: EXIT
>> [ 89.917422] mmc0: SDHCI controller on MMC [sdhci-pxa.0] using DMA
>> [ 89.935552] mmc1: no vmmc regulator found
>> [ 89.950739] NOT SDIO/SD/MMC
>> [ 89.959061] mmc_rescan:mmc0 FAIL
>> [ 89.968661] mmc0: mmc_rescan: trying to init card at 300000 Hz
>> [ 89.986039] mmc_start_host:mmc1: ENTER
>> [ 89.997404] mmc_detect_change: mmc1: ENTER
>> [ 90.009585] mmc_schedule_delayed_work: ENTER
>> [ 90.025342] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 90.039396] NOT SDIO/SD/MMC
>> [ 90.047703] mmc_rescan:mmc0 FAIL
>> [ 90.057304] mmc0: mmc_rescan: trying to init card at 200000 Hz
>> [ 90.074664] mmc_detect_change: mmc1: EXIT
>> [ 90.086698] mmc1: SDHCI controller on MMC [sdhci-pxa.1] using DMA
>> [ 90.104817] mmc2: no vmmc regulator found
>> [ 90.119917] mmc_start_host:mmc2: ENTER
>> [ 90.131280] NOT SDIO/SD/MMC
>> [ 90.139585] mmc_rescan:mmc0 FAIL
>> [ 90.149271] mmc0: mmc_rescan: trying to init card at 100000 Hz
>> [ 90.166643] mmc_detect_change: mmc2: ENTER
>> [ 90.178818] mmc_schedule_delayed_work: ENTER
>> [ 90.191703] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 90.205696] mmc_detect_change: mmc2: EXIT
>> [ 90.220729] NOT SDIO/SD/MMC
>> [ 90.229042] mmc_rescan:mmc0 FAIL
>> [ 90.238638] mmc2: SDHCI controller on MMC [sdhci-pxa.2] using DMA
>> [ 90.256770] TCP cubic registered
>> [ 90.256954] NET: Registered protocol family 17
>> [ 90.279805] Registering the dns_resolver key type
>> [ 90.293787] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5
>> [ 90.318180] max8925-rtc max8925-rtc: setting system clock to 2007-02-05 22:39:20 UTC (1170715160)
>> [ 90.344586] Waiting 5sec before mounting root device...
>> [ 95.366580] Root-NFS: no NFS server address
>> [ 95.379055] VFS: Unable to mount root fs via NFS, trying floppy.
>> [ 95.397037] mmc_rescan:mmc1: ENTER
>> [ 95.407528] VFS: Cannot open root device "mmcblk0p1" or unknown-block(2,0)
>> [ 95.428065] mmc1: mmc_rescan: trying to init card at 400000 Hz
>> [ 95.445444] Please append a correct "root=" boot option; here are the available partitions:
>> [ 95.470345] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
>> [ 95.494941] [<c002a9a8>] (unwind_backtrace+0x0/0x128) from [<c0274dc8>] (panic+0x70/0x184)
>> [ 95.519606] [<c0274dc8>] (panic+0x70/0x184) from [<c0008d50>] (mount_block_root+0x1cc/0x20c)
>> [ 95.544688] [<c0008d50>] (mount_block_root+0x1cc/0x20c) from [<c0008e30>] (mount_root+0xa0/0xc0)
>> [ 95.570868] [<c0008e30>] (mount_root+0xa0/0xc0) from [<c0008f6c>] (prepare_namespace+0x11c/0x174)
>> [ 95.597260] [<c0008f6c>] (prepare_namespace+0x11c/0x174) from [<c0008444>] (kernel_init+0x110/0x150)
>> [ 95.624473] [<c0008444>] (kernel_init+0x110/0x150) from [<c00260e0>] (kernel_thread_exit+0x0/0x8)
>>
>>
>>
>> The following change makes things work --- IS THIS SAFE -?
>>
>> static int __init mmc_init(void)
>> {
>> int ret;
>>
>> #if 0
>> workqueue = create_singlethread_workqueue("kmmcd");
>> #else
>> workqueue = create_workqueue("kmmcd");
>> #endif
>> if (!workqueue)
>> return -ENOMEM;
>>
>>
>> [ 1.680952] mousedev: PS/2 mouse device common for all mice
>> [ 1.698753] max8925-rtc max8925-rtc: rtc core: registered max8925-rtc as rtc0
>> [ 1.720238] sdhci: Secure Digital Host Controller Interface driver
>> [ 1.738743] sdhci: Copyright(c) Pierre Ossman
>> [ 1.751705] mmc0: no vmmc regulator found
>> [ 1.763764] mmc_start_host:mmc0: ENTER
>> [ 1.775028] mmc_detect_change: mmc0: work = df94bd50 ENTER
>> [ 1.791367] mmc_schedule_delayed_work: work = df94bd50 ENTER
>> [ 1.808194] mmc_rescan:mmc0: work = df94bd50 ENTER
>> [ 1.822464] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 1.836436] mmc0: mmc_rescan: trying to init card at 400000 Hz
>> [ 1.853812] mmc_detect_change: mmc0: EXIT
>> [ 1.865717] mmc0: SDHCI controller on MMC [sdhci-pxa.0] using DMA
>> [ 1.883843] mmc1: no vmmc regulator found
>> [ 1.895867] mmc_start_host:mmc1: ENTER
>> [ 1.907217] mmc_detect_change: mmc1: work = df94b950 ENTER
>> [ 1.926684] NOT SDIO/SD/MMC
>> [ 1.935001] mmc_schedule_delayed_work: work = df94b950 ENTER
>> [ 1.951835] mmc_rescan:mmc0 FAIL
>> [ 1.961423] mmc0: mmc_rescan: trying to init card at 300000 Hz
>> [ 1.978795] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 1.992779] mmc_detect_change: mmc1: EXIT
>> [ 2.004701] mmc1: SDHCI controller on MMC [sdhci-pxa.1] using DMA
>> [ 2.023003] mmc2: no vmmc regulator found
>> [ 2.034943] mmc_start_host:mmc2: ENTER
>> [ 2.049483] NOT SDIO/SD/MMC
>> [ 2.057800] mmc_detect_change: mmc2: work = df94b550 ENTER
>> [ 2.074191] mmc_rescan:mmc0 FAIL
>> [ 2.083788] mmc0: mmc_rescan: trying to init card at 200000 Hz
>> [ 2.101161] mmc_schedule_delayed_work: work = df94b550 ENTER
>> [ 2.117985] mmc_schedule_delayed_work: x = 1 EXIT
>> [ 2.132036] mmc_detect_change: mmc2: EXIT
>> [ 2.144059] mmc2: SDHCI controller on MMC [sdhci-pxa.2] using DMA
>> [ 2.162384] TCP cubic registered
>> [ 2.175181] NOT SDIO/SD/MMC
>> [ 2.183513] NET: Registered protocol family 17
>> [ 2.196730] mmc_rescan:mmc0 FAIL
>> [ 2.206388] Registering the dns_resolver key type
>> [ 2.220386] mmc0: mmc_rescan: trying to init card at 100000 Hz
>> [ 2.237749] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 5
>> [ 2.262155] max8925-rtc max8925-rtc: setting system clock to 2007-02-05 23:22:44 UTC (1170717764)
>> [ 2.288769] Waiting 5sec before mounting root device...
>> [ 2.307747] NOT SDIO/SD/MMC
>> [ 2.316086] mmc_rescan:mmc0 FAIL
>> [ 2.325673] mmc_rescan:mmc1: work = df94b950 ENTER
>> [ 2.339951] mmc1: mmc_rescan: trying to init card at 400000 Hz
>> [ 2.399680] NOT SDIO/SD/MMC
>> [ 2.408001] mmc_rescan:mmc1 FAIL
>> [ 2.417581] mmc1: mmc_rescan: trying to init card at 300000 Hz
>> [ 2.480967] NOT SDIO/SD/MMC
>> [ 2.489284] mmc_rescan:mmc1 FAIL
>> [ 2.498867] mmc1: mmc_rescan: trying to init card at 200000 Hz
>> [ 2.563544] NOT SDIO/SD/MMC
>> [ 2.563551] mmc_rescan:mmc1 FAIL
>> [ 2.581423] mmc1: mmc_rescan: trying to init card at 100000 Hz
>> [ 2.651318] NOT SDIO/SD/MMC
>> [ 2.659632] mmc_rescan:mmc1 FAIL
>> [ 2.669232] mmc_rescan:mmc2: work = df94b550 ENTER
>> [ 2.683465] mmc2: mmc_rescan: trying to init card at 400000 Hz
>> [ 2.777696] mmc2: new high speed MMC card at address 0001
>> [ 2.794089] mmcblk0: mmc2:0001 SEM08G 7.39 GiB
>> [ 2.813042] mmcblk0: p1
>> [ 7.325888] EXT3-fs: barriers not enabled
>> [ 7.398090] EXT3-fs (mmcblk0p1):
>> [ 7.407518] kjournald starting. Commit interval 5 seconds
>> [ 7.424361] warning: mounting unchecked fs, running e2fsck is recommended
>> [ 7.445876] EXT3-fs (mmcblk0p1): using internal journal
>> [ 7.455234] EXT3-fs (mmcblk0p1): recovery complete
>> [ 7.476877] EXT3-fs (mmcblk0p1): mounted filesystem with ordered data mode
>> [ 7.497416] VFS: Mounted root (ext3 filesystem) on device 179:1.
>> [ 7.515291] Freeing init memory: 92K
>> init started: BusyBox v1.01 (2009.03.10-14:28+0000) multi-call binary
>> mount: Mounting none on /tmp failed: No such file or directory
>> telnetd: daemon: No such file or directory
>> cannot open /dev/null
>> [ 7.925389] udevd (57): /proc/57/oom_adj is deprecated, please use /proc/57/oom_score_adj instead.
>> cannot open /dev/null
>> error initializing udevd socket
>> modprobe: could not parse modules.dep
>>
>> cannot open /dev/null
>> error initializing udevd socket
>> cannot open /dev/null
>> error initializing udevd socket
>> cannot open /dev/null
>> error initializing udevd socket
>> [ 9.061143] MTD: Attempt to mount non-MTD device "/dev/mmcblk0p1"
>> device '/dev/ttyS2' does not exist.
>> [ 9.597226] MTD: Attempt to mount non-MTD device "/dev/mmcblk0p1"
>>
>>
>> BusyBox v1.01 (2009.03.10-14:28+0000) Built-in shell (ash)
>> Enter 'help' for a list of built-in commands.
>>
>>
>> Processing /etc/profile... ln: /var/dpf/target/: File exists
>> [ 10.209832] MTD: Attempt to mount non-MTD device "/dev/mmcblk0p1"
>> error: cannot open /dev/i2c-user
>> error: cannot open /dev/i2c-user
>> insmod: /lib/modules/2.6.37-rc5-next-20101208-00003-g4ee4acc-dirty: No such file or directory
>> Using /lib/modules/galcore.ko
>> [ 10.498543] galcore: version magic '2.6.28 mod_unload modversions ARMv5 ' should be '2.6.37-rc5-next-20101208-00003-g4ee4acc-dirty preempt mod_unload ARMv6 '
>> insmod: cannot insert `/lib/modules/galcore.ko': Invalid module format (-1): Exec format error
>> insmod: /lib/modules/2.6.37-rc5-next-20101208-00003-g4ee4acc-dirty: No such file or directory
>> insmod: sd8688.ko: no module by that name found
>> [ 10.927510] MTD: Attempt to mount non-MTD device "/dev/mmcblk0p1"
>> VERIFY ID: numid=81,iface=MIXER,name=''
>> amixer: Control default open error: No such device
>>
>> VERIFY ID: numid=85,iface=MIXER,name=''
>> amixer: Control default open error: No such device
>>
>> VERIFY ID: numid=1,iface=MIXER,name=''
>> amixer: Control default open error: No such device
>>
>> VERIFY ID: numid=3,iface=MIXER,name=''
>> amixer: Control default open error: No such device
>>
>> VERIFY ID: numid=4,iface=MIXER,name=''
>> amixer: Control default open error: No such device
>>
>> Done
>>
>> Philip
>>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@...r.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists