Message-Id: <1294343654-20354-3-git-send-email-ptyser@xes-inc.com>
Date:	Thu,  6 Jan 2011 13:54:14 -0600
From:	Peter Tyser <ptyser@...-inc.com>
To:	linux-kernel@...r.kernel.org
Cc:	Peter Tyser <ptyser@...-inc.com>, Alek Du <alek.du@...el.com>,
	Samuel Ortiz <sameo@...ux.intel.com>,
	David Brownell <dbrownell@...rs.sourceforge.net>,
	Eric Miao <eric.y.miao@...il.com>,
	Uwe Kleine-K?nig <u.kleine-koenig@...gutronix.de>,
	Mark Brown <broonie@...nsource.wolfsonmicro.com>,
	Joe Perches <joe@...ches.com>
Subject: [PATCH 3/3] gpio: Add support for Intel ICHx/3100/Series[56] GPIO

This driver works on many Intel chipsets, including the ICH6, ICH7,
ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200
(Cougar Point).

Additional Intel chipsets should be easily supported if needed, eg the
ICH1-5, EP80579, etc.

Tested on a QM57 (Ibex Peak) and 3100.

Cc: Alek Du <alek.du@...el.com>
Cc: Samuel Ortiz <sameo@...ux.intel.com>
Cc: David Brownell <dbrownell@...rs.sourceforge.net>
Cc: Eric Miao <eric.y.miao@...il.com>
Cc: Uwe Kleine-K?nig <u.kleine-koenig@...gutronix.de>
Cc: Mark Brown <broonie@...nsource.wolfsonmicro.com>
Cc: Joe Perches <joe@...ches.com>
Signed-off-by: Peter Tyser <ptyser@...-inc.com>
---
 MAINTAINERS              |    5 +
 drivers/gpio/Kconfig     |   11 +
 drivers/gpio/Makefile    |    1 +
 drivers/gpio/ichx_gpio.c |  551 ++++++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 568 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/ichx_gpio.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 71e40f9..95df3b9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2946,6 +2946,11 @@ W:	http://www.developer.ibm.com/welcome/netfinity/serveraid.html
 S:	Supported
 F:	drivers/scsi/ips.*
 
+ICHX GPIO DRIVER
+M:	Peter Tyser <ptyser@...-inc.com>
+S:	Maintained
+F:	drivers/gpio/ichx_gpio.c
+
 IDE SUBSYSTEM
 M:	"David S. Miller" <davem@...emloft.net>
 L:	linux-ide@...r.kernel.org
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 3143ac7..aa5f540 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -319,6 +319,17 @@ config GPIO_BT8XX
 
 	  If unsure, say N.
 
+config GPIO_ICHX
+	tristate "Intel ICHx GPIO"
+	depends on PCI && GPIOLIB && X86
+	help
+	  Say yes here to support the GPIO functionality of a number of Intel
+	  ICH-based chipsets.  Currently supported devices: ICH6, ICH7, ICH8
+	  ICH9, ICH10, Series 5/3400 (ie Ibex Peak), Series 6/C200 (eg
+	  Cougar Point), and 3100.
+
+	  If unsure, say N.
+
 config GPIO_LANGWELL
 	bool "Intel Langwell/Penwell GPIO support"
 	depends on PCI
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index bdf3dde..d02cf70 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_GPIOLIB)		+= gpiolib.o
 obj-$(CONFIG_GPIO_ADP5520)	+= adp5520-gpio.o
 obj-$(CONFIG_GPIO_ADP5588)	+= adp5588-gpio.o
 obj-$(CONFIG_GPIO_BASIC_MMIO)	+= basic_mmio_gpio.o
+obj-$(CONFIG_GPIO_ICHX)		+= ichx_gpio.o
 obj-$(CONFIG_GPIO_LANGWELL)	+= langwell_gpio.o
 obj-$(CONFIG_GPIO_MAX730X)	+= max730x.o
 obj-$(CONFIG_GPIO_MAX7300)	+= max7300.o
diff --git a/drivers/gpio/ichx_gpio.c b/drivers/gpio/ichx_gpio.c
new file mode 100644
index 0000000..63d27b5
--- /dev/null
+++ b/drivers/gpio/ichx_gpio.c
@@ -0,0 +1,551 @@
+/*
+ * Intel ICH6-10, Series 5 and 6 GPIO driver
+ *
+ * Copyright (C) 2010 Extreme Engineering Solutions.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+
+#define DRV_NAME "ichx_gpio"
+
+/* PCI config register offsets into LPC I/F - D31:F0 */
+#define PCI_ICHX_ACPI_BAR	0x40
+#define PCI_ICHX_GPIO_BAR	0x48
+#define PCI_ICHX_GPIO_CTRL	0x4C
+
+/*
+ * GPIO register offsets in GPIO I/O space.
+ * Each chunk of 32 GPIOs is manipulated via its own USE_SELx, IO_SELx, and
+ * LVLx registers.  Logic in the read/write functions takes a register and
+ * an absolute bit number and determines the proper register offset and bit
+ * number in that register.  For example, to read the value of GPIO bit 50
+ * the code would access offset ichx_regs[2(=GPIO_LVL)][1(=50/32)],
+ * bit 18 (50%32).
+ */
+enum GPIO_REG {
+	GPIO_USE_SEL = 0,
+	GPIO_IO_SEL,
+	GPIO_LVL,
+};
+static const u8 ichx_regs[3][3] = {
+	{0x00, 0x30, 0x40},	/* USE_SEL[1-3] offsets */
+	{0x04, 0x34, 0x44},	/* IO_SEL[1-3] offsets */
+	{0x0c, 0x38, 0x48},	/* LVL[1-3] offsets */
+};
+
+#define ICHX_GPIO_WRITE(val, reg)	outl(val, (reg) + ichx_priv.gpio_base)
+#define ICHX_GPIO_READ(reg)		inl((reg) + ichx_priv.gpio_base)
+#define ICHX_PM_WRITE(val, reg)		outl(val, (reg) + ichx_priv.pm_base)
+#define ICHX_PM_READ(reg)		inl((reg) + ichx_priv.pm_base)
+
+/* Convenient wrapper to make our PCI ID table */
+#define ICHX_GPIO_PCI_DEVICE(dev, data) \
+	.vendor = PCI_VENDOR_ID_INTEL,	\
+	.device = dev,			\
+	.subvendor = PCI_ANY_ID,	\
+	.subdevice = PCI_ANY_ID,	\
+	.class = 0,			\
+	.class_mask = 0,		\
+	.driver_data = (ulong)data
+
+struct ichx_desc {
+	/* Max GPIO pins the chipset can have */
+	uint ngpio;
+
+	/* The offset of GPE0_STS in the PM IO region, 0 if unneeded */
+	uint gpe0_sts_ofs;
+
+	/* USE_SEL is bogus on some chipsets, eg 3100 */
+	u32 use_sel_ignore[3];
+
+	/* Some chipsets have quirks, let these use their own request/get */
+	int (*request)(struct gpio_chip *chip, unsigned offset);
+	int (*get)(struct gpio_chip *chip, unsigned offset);
+};
+
+static struct {
+	spinlock_t lock;
+	struct platform_device *dev;
+	struct pci_dev *pdev;
+	struct gpio_chip chip;
+	unsigned long gpio_base;/* GPIO IO base */
+	unsigned long pm_base;	/* Power Mangagment IO base */
+	struct ichx_desc *desc;	/* Pointer to chipset-specific description */
+	u32 orig_gpio_ctrl;	/* Orig CTRL value, used to restore on exit */
+} ichx_priv;
+
+static struct platform_device *ichx_gpio_platform_device;
+
+static int modparam_gpiobase = -1 /* dynamic */;
+module_param_named(gpiobase, modparam_gpiobase, int, 0444);
+MODULE_PARM_DESC(gpiobase, "The GPIO number base. -1 means dynamic, "
+			   "which is the default.");
+
+static int ichx_write_bit(int reg, unsigned nr, int val, int verify)
+{
+	unsigned long flags;
+	u32 data;
+	int reg_nr = nr / 32;
+	int bit = nr & 0x1f;
+	int ret = 0;
+
+	spin_lock_irqsave(&ichx_priv.lock, flags);
+
+	data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]);
+	data = (data & ~(1 << bit)) | (val << bit);
+	ICHX_GPIO_WRITE(data, ichx_regs[reg][reg_nr]);
+	if (verify && (data != ICHX_GPIO_READ(ichx_regs[reg][reg_nr])))
+		ret = -EPERM;
+
+	spin_unlock_irqrestore(&ichx_priv.lock, flags);
+
+	return ret;
+}
+
+static int ichx_read_bit(int reg, unsigned nr)
+{
+	unsigned long flags;
+	u32 data;
+	int reg_nr = nr / 32;
+	int bit = nr & 0x1f;
+
+	spin_lock_irqsave(&ichx_priv.lock, flags);
+
+	data = ICHX_GPIO_READ(ichx_regs[reg][reg_nr]);
+
+	spin_unlock_irqrestore(&ichx_priv.lock, flags);
+
+	return data & (1 << bit) ? 1 : 0;
+}
+
+static int ichx_gpio_direction_input(struct gpio_chip *gpio, unsigned nr)
+{
+	/*
+	 * Try setting pin as an input and verify it worked since many pins
+	 * are output-only.
+	 */
+	if (ichx_write_bit(GPIO_IO_SEL, nr, 1, 1))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int ichx_gpio_direction_output(struct gpio_chip *gpio, unsigned nr,
+					int val)
+{
+	/* Set GPIO output value. */
+	ichx_write_bit(GPIO_LVL, nr, val, 0);
+
+	/*
+	 * Try setting pin as an output and verify it worked since many pins
+	 * are input-only.
+	 */
+	if (ichx_write_bit(GPIO_IO_SEL, nr, 0, 1))
+		return -EINVAL;
+
+	return 0;
+}
+
+static int ichx_gpio_get_direction(struct gpio_chip *chip, unsigned nr)
+{
+	/* Return 0 if IO pin is input, 1 if its an output */
+	return !ichx_read_bit(GPIO_IO_SEL, nr);
+}
+
+static int ichx_gpio_get(struct gpio_chip *chip, unsigned nr)
+{
+	return ichx_read_bit(GPIO_LVL, nr);
+}
+
+static int ich6_gpio_get(struct gpio_chip *chip, unsigned nr)
+{
+	unsigned long flags;
+	u32 data;
+
+	/*
+	 * GPI 0 - 15 need to be read from the power management registers on
+	 * a ICH6/3100 bridge.
+	 */
+	if (nr < 16) {
+		spin_lock_irqsave(&ichx_priv.lock, flags);
+
+		/* GPI 0 - 15 are latched, write 1 to clear*/
+		ICHX_PM_WRITE(1 << (16 + nr), ichx_priv.desc->gpe0_sts_ofs);
+
+		data = ICHX_PM_READ(ichx_priv.desc->gpe0_sts_ofs);
+
+		spin_unlock_irqrestore(&ichx_priv.lock, flags);
+
+		return (data >> 16) & (1 << nr) ? 1 : 0;
+	} else {
+		return ichx_gpio_get(chip, nr);
+	}
+}
+
+static int ichx_gpio_request(struct gpio_chip *chip, unsigned nr)
+{
+	/*
+	 * Note we assume the BIOS properly set a bridge's USE value.  Some
+	 * chips (eg Intel 3100) have bogus USE values though, so first see if
+	 * the chipset's USE value can be trusted for this specific bit.
+	 * If it can't be trusted, assume that the pin can be used as a GPIO.
+	 */
+	if (ichx_priv.desc->use_sel_ignore[nr / 32] & (1 << (nr & 0x1f)))
+		return 1;
+
+	return ichx_read_bit(GPIO_USE_SEL, nr) ? 0 : -ENODEV;
+}
+
+static int ich6_gpio_request(struct gpio_chip *chip, unsigned nr)
+{
+	/*
+	 * Fixups for bits 16 and 17 are necessary on the Intel ICH6/3100
+	 * brdige as they are controlled by USE register bits 0 and 1.  See
+	 * "Table 704 GPIO_USE_SEL1 register" in the i3100 datasheet for
+	 * additional info.
+	 */
+	if ((nr == 16) || (nr == 17))
+		nr -= 16;
+
+	return ichx_gpio_request(chip, nr);
+}
+
+static void ichx_gpio_set(struct gpio_chip *chip, unsigned nr, int val)
+{
+	ichx_write_bit(GPIO_LVL, nr, val, 0);
+}
+
+static void __devinit ichx_gpiolib_setup(struct gpio_chip *chip)
+{
+	chip->owner = THIS_MODULE;
+	chip->label = DRV_NAME;
+
+	/* Allow chip-specific overrides of request()/get() */
+	chip->request = ichx_priv.desc->request ?
+		ichx_priv.desc->request : ichx_gpio_request;
+	chip->get = ichx_priv.desc->get ?
+		ichx_priv.desc->get : ichx_gpio_get;
+
+	chip->set = ichx_gpio_set;
+	chip->get_direction = ichx_gpio_get_direction;
+	chip->direction_input = ichx_gpio_direction_input;
+	chip->direction_output = ichx_gpio_direction_output;
+	chip->base = modparam_gpiobase;
+	chip->ngpio = ichx_priv.desc->ngpio;
+	chip->can_sleep = 0;
+	chip->dbg_show = NULL;
+}
+
+static int __devinit ichx_gpio_init(struct pci_dev *pdev,
+				const struct pci_device_id *ent,
+				struct platform_device *dev)
+{
+	int err;
+
+	ichx_priv.pdev = pdev;
+	ichx_priv.dev = dev;
+	ichx_priv.desc = (struct ichx_desc *)ent->driver_data;
+
+	/* Determine I/O address of GPIO registers */
+	pci_read_config_dword(pdev, PCI_ICHX_GPIO_BAR,
+			      (u32 *)&ichx_priv.gpio_base);
+	ichx_priv.gpio_base &= PCI_BASE_ADDRESS_IO_MASK;
+	if (!ichx_priv.gpio_base) {
+		printk(KERN_ERR "%s: GPIO BAR not enumerated\n", DRV_NAME);
+		return -ENODEV;
+	}
+
+	/*
+	 * If necessary, determine the I/O address of ACPI/power management
+	 * registers which are needed to read the the GPE0 register for GPI pins
+	 * 0 - 15 on some chipsets.
+	 */
+	if (ichx_priv.desc->gpe0_sts_ofs) {
+		pci_read_config_dword(pdev, PCI_ICHX_ACPI_BAR,
+				      (u32 *)&ichx_priv.pm_base);
+		ichx_priv.pm_base &= PCI_BASE_ADDRESS_IO_MASK;
+		if (!ichx_priv.pm_base)
+			printk(KERN_WARNING "%s: ACPI BAR not enumerated, "
+			       "GPI 0 - 15 unusable\n", DRV_NAME);
+	}
+
+	/* Enable GPIO */
+	pci_read_config_dword(pdev, PCI_ICHX_GPIO_CTRL,
+			&ichx_priv.orig_gpio_ctrl);
+	pci_write_config_dword(pdev, PCI_ICHX_GPIO_CTRL,
+			ichx_priv.orig_gpio_ctrl | 0x10);
+
+	/*
+	 * Reserve GPIO I/O region. The power management region is used by other
+	 * drivers thus shouldn't be reserved.  The GPIO I/O region is 64
+	 * bytes for older chipsets with <= 64 GPIO, 128 bytes for newer
+	 * chipsets with > 64 GPIO.
+	 */
+	if (!devm_request_region(&dev->dev, ichx_priv.gpio_base,
+			ichx_priv.desc->ngpio > 64 ? 128 : 64,
+			"ichxgpio")) {
+		printk(KERN_ERR "%s: Can't request iomem (0x%lx)\n",
+		       DRV_NAME, ichx_priv.gpio_base);
+		return -EBUSY;
+	}
+
+	ichx_gpiolib_setup(&ichx_priv.chip);
+
+	err = gpiochip_add(&ichx_priv.chip);
+	if (err) {
+		printk(KERN_ERR "%s: Failed to register GPIOs\n", DRV_NAME);
+		return err;
+	}
+
+	printk(KERN_INFO "%s: GPIO from %d to %d on %s\n", DRV_NAME,
+	       ichx_priv.chip.base,
+	       ichx_priv.chip.base + ichx_priv.chip.ngpio - 1,
+	       dev_name(&pdev->dev));
+
+	return 0;
+}
+
+/* ICH6-based, 631xesb-based */
+static struct ichx_desc ich6_desc = {
+	/* Bridges using the ICH6 controller need fixups for GPIO 0 - 17 */
+	.request = ich6_gpio_request,
+	.get = ich6_gpio_get,
+
+	/* GPIO 0-15 are read in the GPE0_STS PM register */
+	.gpe0_sts_ofs = 0x28,
+
+	.ngpio = 50,
+};
+
+/* Intel 3100 */
+static struct ichx_desc i3100_desc = {
+	/*
+	 * Bits 16,17, 20 of USE_SEL and bit 16 of USE_SEL2 always read 0 on
+	 * the Intel 3100.  See "Table 712. GPIO Summary Table" of 3100
+	 * Datasheet for more info.
+	 */
+	.use_sel_ignore = {0x00130000, 0x00010000, 0x0},
+
+	/* The 3100 needs fixups for GPIO 0 - 17 */
+	.request = ich6_gpio_request,
+	.get = ich6_gpio_get,
+
+	/* GPIO 0-15 are read in the GPE0_STS PM register */
+	.gpe0_sts_ofs = 0x28,
+
+	.ngpio = 50,
+};
+
+/* ICH7 and ICH8-based */
+static struct ichx_desc ich7_desc = {
+	.ngpio = 50,
+};
+
+/* ICH9-based */
+static struct ichx_desc ich9_desc = {
+	.ngpio = 61,
+};
+
+/* ICH10-based - Consumer/corporate versions have different amount of GPIO */
+static struct ichx_desc ich10_cons_desc = {
+	.ngpio = 51,
+};
+static struct ichx_desc ich10_corp_desc = {
+	.ngpio = 72,
+};
+
+/* Intel 5 series, 6 series, 3400 series, and C200 series */
+static struct ichx_desc intel5_desc = {
+	.ngpio = 76,
+};
+
+/*
+ * Note that we don't register a PCI driver since the PCI device has additional
+ * functionality that is used by other drivers, eg iTCO_wdt.  We use the table
+ * to probe for matching devices, then use a platform driver.
+ *
+ * Also note that some additional, old chipsets should in theory be supported
+ * by this driver (eg 82801XX chips), but they are left out due to the fact
+ * that they complicate the driver and there likely isn't much of a demand
+ * since a driver doesn't already exist for the 10+ years the chipsets have
+ * existed for.
+ */
+static DEFINE_PCI_DEVICE_TABLE(ichx_pci_tbl) = {
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_0, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_1, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH6_2, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_0, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_1, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_30, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH7_31, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_0, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_1, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_2, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_3, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH8_4, &ich7_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_1, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_2, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_4, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_5, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_7, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH9_8, &ich9_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_0, &ich10_corp_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_3, &ich10_corp_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_1, &ich10_cons_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ICH10_2, &ich10_cons_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(PCI_DEVICE_ID_INTEL_ESB2_0, &i3100_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2671, &ich6_desc) }, /* 631Xesb series */
+	{ ICHX_GPIO_PCI_DEVICE(0x2672, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2673, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2674, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2675, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2676, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2677, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2678, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x2679, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267a, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267b, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267c, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267d, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267e, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x267f, &ich6_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b00, &intel5_desc) }, /* 5 series */
+	{ ICHX_GPIO_PCI_DEVICE(0x3b01, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b02, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b03, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b04, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b05, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b06, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b07, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b08, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b09, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0a, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0b, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0c, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0d, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0e, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b0f, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c41, &intel5_desc) }, /* 6 Series */
+	{ ICHX_GPIO_PCI_DEVICE(0x1c42, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c43, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c44, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c45, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c46, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c47, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c48, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c49, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4a, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4b, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4c, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4d, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4e, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c4f, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c50, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c51, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c52, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c53, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c54, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c55, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c56, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c57, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c58, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c59, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5a, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5b, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5c, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5d, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5e, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x1c5f, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b12, &intel5_desc) }, /* 3400 series */
+	{ ICHX_GPIO_PCI_DEVICE(0x3b14, &intel5_desc) },
+	{ ICHX_GPIO_PCI_DEVICE(0x3b16, &intel5_desc) },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, ichx_pci_tbl);
+
+static int __devinit ichx_gpio_probe(struct platform_device *dev)
+{
+	struct pci_dev *pdev = NULL;
+	const struct pci_device_id *ent;
+
+	spin_lock_init(&ichx_priv.lock);
+
+	for_each_pci_dev(pdev) {
+		ent = pci_match_id(ichx_pci_tbl, pdev);
+		if (ent)
+			return ichx_gpio_init(pdev, ent, dev);
+	}
+
+	return -ENODEV;
+}
+
+static int __devexit ichx_gpio_remove(struct platform_device *dev)
+{
+	int ret = gpiochip_remove(&ichx_priv.chip);
+
+	/* Restore original GPIO control register value */
+	pci_write_config_dword(ichx_priv.pdev, PCI_ICHX_GPIO_CTRL,
+			ichx_priv.orig_gpio_ctrl);
+
+	return ret;
+}
+
+static struct platform_driver ichx_gpio_driver = {
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= DRV_NAME,
+	},
+	.probe		= ichx_gpio_probe,
+	.remove		= __devexit_p(ichx_gpio_remove),
+};
+
+static int __devinit ichx_gpio_init_module(void)
+{
+	int err = platform_driver_register(&ichx_gpio_driver);
+	if (err)
+		return err;
+
+	ichx_gpio_platform_device =
+		platform_device_register_simple(DRV_NAME, -1, NULL, 0);
+
+	if (IS_ERR(ichx_gpio_platform_device)) {
+		err = PTR_ERR(ichx_gpio_platform_device);
+		goto unreg_platform_driver;
+	}
+
+	return 0;
+
+unreg_platform_driver:
+	platform_driver_unregister(&ichx_gpio_driver);
+	return err;
+}
+
+static void __devexit ichx_gpio_exit_module(void)
+{
+	platform_device_unregister(ichx_gpio_platform_device);
+	platform_driver_unregister(&ichx_gpio_driver);
+}
+
+module_init(ichx_gpio_init_module);
+module_exit(ichx_gpio_exit_module);
+
+MODULE_AUTHOR("Peter Tyser <ptyser@...-inc.com>");
+MODULE_DESCRIPTION("Intel ICHx series bridge GPIO driver");
+MODULE_LICENSE("GPL");
-- 
1.7.0.4

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists