Date:	Wed, 4 May 2011 21:12:05 -0700
From:	Jonathan McDowell <noodles@...th.li>
To:	Grant Likely <grant.likely@...retlab.ca>
Subject: [PATCH] Add support for VSC055 Enhanced Two-Wire Serial Backplane
 controller

I'd been holding off on sending this until I got some feedback about the
PC8741x driver I sent a couple of weeks ago, but seeing as I have it
sitting around I figured I may as well send it anyway.

-----
Add support for the GPIOs on Maxim VSC055 I2C Enhanced Two-Wire Serial
Backplane controller.

This chip features 64 bits of user-definable, bidirectional GPIOs. It also
has the ability to do PWM fan control output and LED flashing, but support
for that functionality is not included at present.

Signed-off-by: Jonathan McDowell <noodles@...th.li>

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index cc150db..4c5de65 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -255,6 +255,13 @@ config GPIO_TWL4030
 	  Say yes here to access the GPIO signals of various multi-function
 	  power management chips from Texas Instruments.
 
+config GPIO_VSC055
+	tristate "VSC055 GPIOs"
+	depends on I2C
+	help
+	  Say yes here to access the GPIOs found on the Maxim VSC055 Enhanced
+	  Two-Wire Serial Backplane controller.
+
 config GPIO_WM831X
 	tristate "WM831x GPIOs"
 	depends on MFD_WM831X
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index d2752b2..f82491d 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -42,4 +42,5 @@ obj-$(CONFIG_GPIO_RDC321X)	+= rdc321x-gpio.o
 obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
 obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o
 obj-$(CONFIG_GPIO_VX855)	+= vx855_gpio.o
+obj-$(CONFIG_GPIO_VSC055)	+= vsc055.o
 obj-$(CONFIG_GPIO_ML_IOH)	+= ml_ioh_gpio.o
diff --git a/drivers/gpio/vsc055.c b/drivers/gpio/vsc055.c
new file mode 100644
index 0000000..c218dac
--- /dev/null
+++ b/drivers/gpio/vsc055.c
@@ -0,0 +1,326 @@
+/*
+ *  vsc055.c - Enhanced Two-Wire Serial Backplane Control with 64 I/O lines.
+ *
+ *  Copyright (C) 2011 Jonathan McDowell <noodles@...th.li>
+ *
+ *  Derived from drivers/gpio/pca953x.c
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/i2c/vsc055.h>
+#include <linux/slab.h>
+
+#define VSC055_GPD0		0x00
+#define VSC055_DDP0		0x10
+#define VSC055_BCIS		0xF8
+#define VSC055_BCT		0xFC
+#define VSC055_VER		0xFF
+
+static const struct i2c_device_id vsc055_id[] = {
+	{ "vsc055" },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, vsc055_id);
+
+struct vsc055_chip {
+	unsigned gpio_start;
+	uint8_t reg_output[8];
+	uint8_t reg_direction[8];
+	struct mutex i2c_lock;
+
+	struct i2c_client *client;
+	struct gpio_chip gpio_chip;
+	const char *const *names;
+};
+
+static int vsc055_write_reg(struct vsc055_chip *chip, int reg, uint8_t val)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte_data(chip->client, reg, val);
+
+	if (ret < 0) {
+		dev_err(&chip->client->dev, "failed writing register\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static int vsc055_read_reg(struct vsc055_chip *chip, int reg, uint8_t *val)
+{
+	int ret;
+
+	ret = i2c_smbus_read_byte_data(chip->client, reg);
+
+	if (ret < 0) {
+		dev_err(&chip->client->dev, "failed reading register\n");
+		return ret;
+	}
+
+	*val = (uint8_t)ret;
+	return 0;
+}
+
+static int vsc055_gpio_direction_input(struct gpio_chip *gc, unsigned off)
+{
+	struct vsc055_chip *chip;
+	uint8_t reg_val;
+	int ret;
+	int block, pin;
+
+	chip = container_of(gc, struct vsc055_chip, gpio_chip);
+
+	block = off >> 3;
+	pin = off & 7;
+
+	mutex_lock(&chip->i2c_lock);
+	reg_val = chip->reg_direction[block] | (1u << pin);
+	ret = vsc055_write_reg(chip, VSC055_DDP0 + block, reg_val);
+	if (ret)
+		goto exit;
+
+	chip->reg_direction[block] = reg_val;
+	ret = 0;
+exit:
+	mutex_unlock(&chip->i2c_lock);
+	return ret;
+}
+
+static int vsc055_gpio_direction_output(struct gpio_chip *gc,
+		unsigned off, int val)
+{
+	struct vsc055_chip *chip;
+	uint8_t reg_val;
+	int ret;
+	int block, pin;
+
+	chip = container_of(gc, struct vsc055_chip, gpio_chip);
+
+	block = off >> 3;
+	pin = off & 7;
+
+	mutex_lock(&chip->i2c_lock);
+	/* set output level */
+	if (val)
+		reg_val = chip->reg_output[block] | (1u << pin);
+	else
+		reg_val = chip->reg_output[block] & ~(1u << pin);
+
+	ret = vsc055_write_reg(chip, VSC055_GPD0 + block, reg_val);
+	if (ret)
+		goto exit;
+
+	chip->reg_output[block] = reg_val;
+
+	/* then direction */
+	reg_val = chip->reg_direction[block] & ~(1u << off);
+	ret = vsc055_write_reg(chip, VSC055_DDP0 + block, reg_val);
+	if (ret)
+		goto exit;
+
+	chip->reg_direction[block] = reg_val;
+	ret = 0;
+exit:
+	mutex_unlock(&chip->i2c_lock);
+	return ret;
+}
+
+static int vsc055_gpio_get_value(struct gpio_chip *gc, unsigned off)
+{
+	struct vsc055_chip *chip;
+	uint8_t reg_val;
+	int ret;
+
+	chip = container_of(gc, struct vsc055_chip, gpio_chip);
+
+	mutex_lock(&chip->i2c_lock);
+	ret = vsc055_read_reg(chip, VSC055_GPD0 + (off >> 3), &reg_val);
+	mutex_unlock(&chip->i2c_lock);
+	if (ret < 0) {
+		/* NOTE:  diagnostic already emitted; that's all we should
+		 * do unless gpio_*_value_cansleep() calls become different
+		 * from their nonsleeping siblings (and report faults).
+		 */
+		return 0;
+	}
+
+	return (reg_val & (1u << (off & 7))) ? 1 : 0;
+}
+
+static void vsc055_gpio_set_value(struct gpio_chip *gc, unsigned off, int val)
+{
+	struct vsc055_chip *chip;
+	uint8_t reg_val;
+	int ret;
+	int block, pin;
+
+	chip = container_of(gc, struct vsc055_chip, gpio_chip);
+
+	block = off >> 3;
+	pin = off & 7;
+
+	mutex_lock(&chip->i2c_lock);
+	if (val)
+		reg_val = chip->reg_output[block] | (1u << pin);
+	else
+		reg_val = chip->reg_output[block] & ~(1u << pin);
+
+	ret = vsc055_write_reg(chip, VSC055_GPD0 + block, reg_val);
+	if (ret)
+		goto exit;
+
+	chip->reg_output[block] = reg_val;
+exit:
+	mutex_unlock(&chip->i2c_lock);
+}
+
+static void vsc055_setup_gpio(struct vsc055_chip *chip)
+{
+	struct gpio_chip *gc;
+
+	gc = &chip->gpio_chip;
+
+	gc->direction_input  = vsc055_gpio_direction_input;
+	gc->direction_output = vsc055_gpio_direction_output;
+	gc->get = vsc055_gpio_get_value;
+	gc->set = vsc055_gpio_set_value;
+	gc->can_sleep = 1;
+
+	gc->base = chip->gpio_start;
+	gc->ngpio = 64;
+	gc->label = chip->client->name;
+	gc->dev = &chip->client->dev;
+	gc->owner = THIS_MODULE;
+	gc->names = chip->names;
+}
+
+static int __devinit vsc055_probe(struct i2c_client *client,
+				   const struct i2c_device_id *id)
+{
+	struct vsc055_platform_data *pdata;
+	struct vsc055_chip *chip;
+	int ret;
+	int i;
+	uint8_t ver;
+
+	chip = kzalloc(sizeof(struct vsc055_chip), GFP_KERNEL);
+	if (chip == NULL)
+		return -ENOMEM;
+
+	pdata = client->dev.platform_data;
+	if (pdata == NULL) {
+		dev_dbg(&client->dev, "no platform data\n");
+		ret = -EINVAL;
+		goto out_failed;
+	}
+
+	chip->client = client;
+
+	chip->gpio_start = pdata->gpio_base;
+
+	chip->names = pdata->names;
+
+	mutex_init(&chip->i2c_lock);
+
+	/* initialize cached registers from their original values.
+	 * we can't share this chip with another i2c master.
+	 */
+	vsc055_setup_gpio(chip);
+
+	for (i = 0; i < 8; i++) {
+		ret = vsc055_read_reg(chip, VSC055_GPD0 + i,
+			&chip->reg_output[i]);
+		if (ret)
+			goto out_failed;
+		ret = vsc055_read_reg(chip, VSC055_DDP0 + i,
+			&chip->reg_direction[i]);
+		if (ret)
+			goto out_failed;
+	}
+
+	ret = vsc055_read_reg(chip, VSC055_VER, &ver);
+	if (ret)
+		goto out_failed;
+	dev_info(&client->dev, "Found VSC055 revision %d.%d\n", ver >> 4, ver & 0xF);
+
+	ret = gpiochip_add(&chip->gpio_chip);
+	if (ret)
+		goto out_failed;
+
+	if (pdata->setup) {
+		ret = pdata->setup(client, chip->gpio_chip.base,
+				chip->gpio_chip.ngpio, pdata->context);
+		if (ret < 0)
+			dev_warn(&client->dev, "setup failed, %d\n", ret);
+	}
+
+	i2c_set_clientdata(client, chip);
+	return 0;
+
+out_failed:
+	kfree(chip);
+	return ret;
+}
+
+static int vsc055_remove(struct i2c_client *client)
+{
+	struct vsc055_platform_data *pdata = client->dev.platform_data;
+	struct vsc055_chip *chip = i2c_get_clientdata(client);
+	int ret = 0;
+
+	if (pdata->teardown) {
+		ret = pdata->teardown(client, chip->gpio_chip.base,
+				chip->gpio_chip.ngpio, pdata->context);
+		if (ret < 0) {
+			dev_err(&client->dev, "%s failed, %d\n",
+					"teardown", ret);
+			return ret;
+		}
+	}
+
+	ret = gpiochip_remove(&chip->gpio_chip);
+	if (ret) {
+		dev_err(&client->dev, "%s failed, %d\n",
+				"gpiochip_remove()", ret);
+		return ret;
+	}
+
+	kfree(chip);
+	return 0;
+}
+
+static struct i2c_driver vsc055_driver = {
+	.driver = {
+		.name	= "vsc055",
+	},
+	.probe		= vsc055_probe,
+	.remove		= vsc055_remove,
+	.id_table	= vsc055_id,
+};
+
+static int __init vsc055_init(void)
+{
+	return i2c_add_driver(&vsc055_driver);
+}
+/* register after i2c postcore initcall and before
+ * subsys initcalls that may rely on these GPIOs
+ */
+subsys_initcall(vsc055_init);
+
+static void __exit vsc055_exit(void)
+{
+	i2c_del_driver(&vsc055_driver);
+}
+module_exit(vsc055_exit);
+
+MODULE_AUTHOR("Jonathan McDowell <noodles@...th.li>");
+MODULE_DESCRIPTION("GPIO driver for VSC055");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/i2c/vsc055.h b/include/linux/i2c/vsc055.h
new file mode 100644
index 0000000..dc1462b
--- /dev/null
+++ b/include/linux/i2c/vsc055.h
@@ -0,0 +1,22 @@
+#ifndef _LINUX_VSC055_H
+#define _LINUX_VSC055_H
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+
+/* Platform data for the VSC055 64-bit I/O expander driver */
+
+struct vsc055_platform_data {
+	unsigned	gpio_base;	/* number of the first GPIO */
+	void		*context;	/* param to setup/teardown */
+
+	int		(*setup)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+	int		(*teardown)(struct i2c_client *client,
+				unsigned gpio, unsigned ngpio,
+				void *context);
+	const char	*const *names;
+};
+
+#endif /* _LINUX_VSC055_H */
-----

J.

-- 
101 things you can't have too much of : 2 - Gaffa tape.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists