| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <4DFA2965.1000708@gmail.com>
Date: Thu, 16 Jun 2011 09:03:49 -0700
From: Dirk Brandewie <dirk.brandewie@...il.com>
To: Grant Likely <grant.likely@...retlab.ca>
CC: dirk.brandewie@...il.com, spi-devel-general@...ts.sourceforge.net,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH 3/5] dw_spi: rework message processing
On 06/16/2011 06:14 AM, Grant Likely wrote:
> On Wed, Jun 15, 2011 at 10:23:06AM -0700, dirk.brandewie@...il.com wrote:
>> From: Dirk Brandewie<dirk.brandewie@...il.com>
>>
>> NOTE: patch created git format-patch --break-rewrites=/50%
>>
>> This patch reworks the message pump worker thread function to run
>> until all messages queued to the driver have been handled. The
>> function to handle individual spi_transfers is now a synchronus
>> function the tasklet to handle spi_transfers has been removed. Work
>> for the worker thread is only queued in host controller transfer
>> function.
>>
>> Psuedo code for new thread function:
>> message = get_message()
>> while (message){
>> for_each_transfer_in_msg(message){
>> transfer_setup(transfer)
>> do_transfer()
>> }
>> complete_message()
>> message = get_message()
>> }
>>
>> Changes that fell out of the message thread changes:
>> Non-DMA transfers that are larger than the size of the controller FIFO
>> are handled as interrupt driven transfers.
>>
>> Common FIFO handling functions shared PIO and interrupt transfers.
>>
>> Simplified queue stop/start funcitons.
>>
>> Cleanup fixes:
>> Changed exported all exported function names to have dw_spi_ prefix
>>
>> Removed support for registering chip select control function. Setting
>> the slave chip select is handled by setting the SER (Slave enable
>> register)
>
> What about for implementations that use a GPIO for the SPI chip
> select? It is very common for board designs to use GPIOs for
> multiplexing the SPI bus.
OK I can put that back. I took it out for the following reason.
The Slave Enable Register (SER) must be set for the IP block to start the
transfer. The bit in SER directly control a separate chip select pin while
there is an active transfer. This gives four chip selects in the direct mapping
case and up to fifteen if the slave chip selects are muxed together.
>
>>
>> Removed code that looked at the cs_change hint in the
>> spi_transfer. Software has no contorl over whether the slave chip
>> select is de-asserted at the end of the transfer. Once the TX FIFO
>> goes empty the slave chip select is dropped.
>
> This sounds wrong. cs_change is *not* merely a hint. It must be respected.
> If the driver has no direct control over the CS line, then it is
> incumbent on the driver to guaranteed that the cs deassert condition
> does not occur. This will probably mean chaining up all the transfers
> in a message so that the TX FIFO remains full. If cs_change is
> requested, then the FIFO must be allowed to empty before kicking of
> the next group of transfers.
>
I agree it is wrong that the driver can not directly control the chip select :-)
I could probably manage to get the PIO and interrupt case to honor this but
would add a fair bit of complexity, I have no idea how to make the DMA case work
I am open to suggestions :-). The current driver has this issue I just made it
explicit maybe we should add a warning message in the driver to let client
driver writers aware of the Silicon behaviour.
ATM I believe that my driver exhibits the same behaviour as the current driver.
I verified this with a logic analyser for the PIO and interrupt case.
>>
>> Added dw_spi_{en,dis}able inline functions to replace spi_enable_chip()
>> Added dw_spi_{mask,umask}_intr inline functions
>>
>> Signed-off-by: Dirk Brandewie<dirk.brandewie@...il.com>
>
> As previously discussed both on-list and off, this is a major rework
> and I'd like to hear from the folks who are affected by this driver
> before I commit to merging it. I don't like merging something so
> large that it ends up basically being a driver rewrite, but if there
> aren't any strong objections, I'll probably grudgingly accept it.
>
I agree, I have no desire to break anyone :-) This driver is in use in all
internal Meego builds for Moorsetown and Medfield based on v2.6.37+ that I am
aware of. It has been tested on the Moorsetown (Sooke harbor) and Meedfield
(iCDK) development along with five different OEM designs.
It is also in use on multiple android based platforms.
> More comments below.
>
>> ---
>> drivers/spi/spi-dw-mid.c | 43 +-
>> drivers/spi/spi-dw.c | 1670 ++++++++++++++++++++--------------------------
>> drivers/spi/spi-dw.h | 92 ++--
>> 3 files changed, 809 insertions(+), 996 deletions(-)
>> rewrite drivers/spi/spi-dw.c (55%)
>>
>> diff --git a/drivers/spi/spi-dw-mid.c b/drivers/spi/spi-dw-mid.c
>> index 130e555..e44e37f 100644
>> --- a/drivers/spi/spi-dw-mid.c
>> +++ b/drivers/spi/spi-dw-mid.c
>> @@ -38,7 +38,10 @@ static bool mid_spi_dma_chan_filter(struct dma_chan *chan, void *param)
>> {
>> struct dw_spi *dws = param;
>>
>> - return dws->dmac&& (&dws->dmac->dev == chan->device->dev);
>> + if (dws->dmac&& &dws->dmac->dev == chan->device->dev)
>> + return true;
>> + else
>> + return false;
>
> Why? The old code is correct, and the new code is more verbose.
>
I will back this change out
>> }
>>
>> static int mid_spi_dma_init(struct dw_spi *dws)
>> @@ -103,10 +106,10 @@ static void dw_spi_dma_done(void *arg)
>>
>> if (++dws->dma_chan_done != 2)
>> return;
>> - dw_spi_xfer_done(dws);
>> + complete(&dws->xfer.complete);
>> }
>>
>> -static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
>> +static int mid_spi_dma_transfer(struct dw_spi *dws)
>> {
>> struct dma_async_tx_descriptor *txdesc = NULL, *rxdesc = NULL;
>> struct dma_chan *txchan, *rxchan;
>> @@ -114,17 +117,17 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
>> u16 dma_ctrl = 0;
>>
>> /* 1. setup DMA related registers */
>> - if (cs_change) {
>> - spi_enable_chip(dws, 0);
>> - dw_writew(dws, dmardlr, 0xf);
>> - dw_writew(dws, dmatdlr, 0x10);
>> - if (dws->tx_dma)
>> - dma_ctrl |= 0x2;
>> - if (dws->rx_dma)
>> - dma_ctrl |= 0x1;
>> - dw_writew(dws, dmacr, dma_ctrl);
>> - spi_enable_chip(dws, 1);
>> - }
>> +
>> + dw_spi_disable(dws);
>> + dw_writew(dws, dmardlr, 0xf);
>> + dw_writew(dws, dmatdlr, 0x10);
>> + if (dws->xfer.tx_dma)
>> + dma_ctrl |= 0x2;
>> + if (dws->xfer.rx_dma)
>> + dma_ctrl |= 0x1;
>> + dw_writew(dws, dmacr, dma_ctrl);
>> + dw_spi_enable(dws);
>> +
>>
>> dws->dma_chan_done = 0;
>> txchan = dws->txchan;
>> @@ -141,8 +144,8 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
>> (unsigned long)&txconf);
>>
>> memset(&dws->tx_sgl, 0, sizeof(dws->tx_sgl));
>> - dws->tx_sgl.dma_address = dws->tx_dma;
>> - dws->tx_sgl.length = dws->len;
>> + dws->tx_sgl.dma_address = dws->xfer.tx_dma;
>> + dws->tx_sgl.length = dws->xfer.len;
>>
>> txdesc = txchan->device->device_prep_slave_sg(txchan,
>> &dws->tx_sgl,
>> @@ -163,8 +166,8 @@ static int mid_spi_dma_transfer(struct dw_spi *dws, int cs_change)
>> (unsigned long)&rxconf);
>>
>> memset(&dws->rx_sgl, 0, sizeof(dws->rx_sgl));
>> - dws->rx_sgl.dma_address = dws->rx_dma;
>> - dws->rx_sgl.length = dws->len;
>> + dws->rx_sgl.dma_address = dws->xfer.rx_dma;
>> + dws->rx_sgl.length = dws->xfer.len;
>>
>> rxdesc = rxchan->device->device_prep_slave_sg(rxchan,
>> &dws->rx_sgl,
>> @@ -188,7 +191,6 @@ static struct dw_spi_dma_ops mid_dma_ops = {
>> #endif
>>
>> /* Some specific info for SPI0 controller on Moorestown */
>> -
>> /* HW info for MRST CLk Control Unit, one 32b reg */
>> #define MRST_SPI_CLK_BASE 100000000 /* 100m */
>> #define MRST_CLK_SPI0_REG 0xff11d86c
>> @@ -202,12 +204,13 @@ int dw_spi_mid_init(struct dw_spi *dws)
>> {
>> u32 *clk_reg, clk_cdiv;
>>
>> +
>
> nit: unrelated whitespace changes
ack
>
>> clk_reg = ioremap_nocache(MRST_CLK_SPI0_REG, 16);
>> if (!clk_reg)
>> return -ENOMEM;
>>
>> /* get SPI controller operating freq info */
>> - clk_cdiv = (readl(clk_reg)& CLK_SPI_CDIV_MASK)>> CLK_SPI_CDIV_OFFSET;
>> + clk_cdiv = ((*clk_reg)& CLK_SPI_CDIV_MASK)>> CLK_SPI_CDIV_OFFSET;
>
> Woah. Changes correct usage of an io accessor to a direct dereference
> of a register? That's not cool. Why is a direct dereference needed
> here? If you have to do something like this, then it must have a
> comment explaining why.
>
I don't remember exactly why I made this change I will back it out and test and
add the appropriate comments if it is still needed.
>> dws->max_freq = MRST_SPI_CLK_BASE / (clk_cdiv + 1);
>> iounmap(clk_reg);
>>
>> diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c
>> dissimilarity index 55%
>> index ece5f69..2dacb8f 100644
>> --- a/drivers/spi/spi-dw.c
>> +++ b/drivers/spi/spi-dw.c
>> @@ -1,936 +1,734 @@
>> -/*
>> - * Designware SPI core controller driver (refer pxa2xx_spi.c)
>> - *
>> - * Copyright (c) 2009, Intel Corporation.
>> - *
>> - * This program is free software; you can redistribute it and/or modify it
>> - * under the terms and conditions of the GNU General Public License,
>> - * version 2, as published by the Free Software Foundation.
>> - *
>> - * This program is distributed in the hope it will be useful, but WITHOUT
>> - * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> - * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
>> - * more details.
>> - *
>> - * You should have received a copy of the GNU General Public License along with
>> - * this program; if not, write to the Free Software Foundation, Inc.,
>> - * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
>> - */
>> -
>> -#include<linux/dma-mapping.h>
>> -#include<linux/interrupt.h>
>> -#include<linux/highmem.h>
>> -#include<linux/delay.h>
>> -#include<linux/slab.h>
>> -#include<linux/spi/spi.h>
>> -
>> -#include "spi-dw.h"
>> -
>> -#ifdef CONFIG_DEBUG_FS
>> -#include<linux/debugfs.h>
>> -#endif
>> -
>> -#define START_STATE ((void *)0)
>> -#define RUNNING_STATE ((void *)1)
>> -#define DONE_STATE ((void *)2)
>> -#define ERROR_STATE ((void *)-1)
>> -
>> -#define QUEUE_RUNNING 0
>> -#define QUEUE_STOPPED 1
>> -
>> -#define MRST_SPI_DEASSERT 0
>> -#define MRST_SPI_ASSERT 1
>> -
>> -/* Slave spi_dev related */
>> -struct chip_data {
>> - u16 cr0;
>> - u8 cs; /* chip select pin */
>> - u8 n_bytes; /* current is a 1/2/4 byte op */
>> - u8 tmode; /* TR/TO/RO/EEPROM */
>> - u8 type; /* SPI/SSP/MicroWire */
>> -
>> - u8 poll_mode; /* 1 means use poll mode */
>> -
>> - u32 dma_width;
>> - u32 rx_threshold;
>> - u32 tx_threshold;
>> - u8 enable_dma;
>> - u8 bits_per_word;
>> - u16 clk_div; /* baud rate divider */
>> - u32 speed_hz; /* baud rate */
>> - void (*cs_control)(u32 command);
>> -};
>> -
>> -#ifdef CONFIG_DEBUG_FS
>> -static int spi_show_regs_open(struct inode *inode, struct file *file)
>> -{
>> - file->private_data = inode->i_private;
>> - return 0;
>> -}
>> -
>> -#define SPI_REGS_BUFSIZE 1024
>> -static ssize_t spi_show_regs(struct file *file, char __user *user_buf,
>> - size_t count, loff_t *ppos)
>> -{
>> - struct dw_spi *dws;
>> - char *buf;
>> - u32 len = 0;
>> - ssize_t ret;
>> -
>> - dws = file->private_data;
>> -
>> - buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL);
>> - if (!buf)
>> - return 0;
>> -
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "MRST SPI0 registers:\n");
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "=================================\n");
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "CTRL0: \t\t0x%08x\n", dw_readl(dws, ctrl0));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "CTRL1: \t\t0x%08x\n", dw_readl(dws, ctrl1));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "SSIENR: \t0x%08x\n", dw_readl(dws, ssienr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "SER: \t\t0x%08x\n", dw_readl(dws, ser));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "BAUDR: \t\t0x%08x\n", dw_readl(dws, baudr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "TXFTLR: \t0x%08x\n", dw_readl(dws, txfltr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "RXFTLR: \t0x%08x\n", dw_readl(dws, rxfltr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "TXFLR: \t\t0x%08x\n", dw_readl(dws, txflr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "RXFLR: \t\t0x%08x\n", dw_readl(dws, rxflr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "SR: \t\t0x%08x\n", dw_readl(dws, sr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "IMR: \t\t0x%08x\n", dw_readl(dws, imr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "ISR: \t\t0x%08x\n", dw_readl(dws, isr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "DMACR: \t\t0x%08x\n", dw_readl(dws, dmacr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "DMATDLR: \t0x%08x\n", dw_readl(dws, dmatdlr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "DMARDLR: \t0x%08x\n", dw_readl(dws, dmardlr));
>> - len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> - "=================================\n");
>> -
>> - ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
>> - kfree(buf);
>> - return ret;
>> -}
>> -
>> -static const struct file_operations mrst_spi_regs_ops = {
>> - .owner = THIS_MODULE,
>> - .open = spi_show_regs_open,
>> - .read = spi_show_regs,
>> - .llseek = default_llseek,
>> -};
>> -
>> -static int mrst_spi_debugfs_init(struct dw_spi *dws)
>> -{
>> - dws->debugfs = debugfs_create_dir("mrst_spi", NULL);
>> - if (!dws->debugfs)
>> - return -ENOMEM;
>> -
>> - debugfs_create_file("registers", S_IFREG | S_IRUGO,
>> - dws->debugfs, (void *)dws,&mrst_spi_regs_ops);
>> - return 0;
>> -}
>> -
>> -static void mrst_spi_debugfs_remove(struct dw_spi *dws)
>> -{
>> - if (dws->debugfs)
>> - debugfs_remove_recursive(dws->debugfs);
>> -}
>> -
>> -#else
>> -static inline int mrst_spi_debugfs_init(struct dw_spi *dws)
>> -{
>> - return 0;
>> -}
>> -
>> -static inline void mrst_spi_debugfs_remove(struct dw_spi *dws)
>> -{
>> -}
>> -#endif /* CONFIG_DEBUG_FS */
>> -
>> -/* Return the max entries we can fill into tx fifo */
>> -static inline u32 tx_max(struct dw_spi *dws)
>> -{
>> - u32 tx_left, tx_room, rxtx_gap;
>> -
>> - tx_left = (dws->tx_end - dws->tx) / dws->n_bytes;
>> - tx_room = dws->fifo_len - dw_readw(dws, txflr);
>> -
>> - /*
>> - * Another concern is about the tx/rx mismatch, we
>> - * though to use (dws->fifo_len - rxflr - txflr) as
>> - * one maximum value for tx, but it doesn't cover the
>> - * data which is out of tx/rx fifo and inside the
>> - * shift registers. So a control from sw point of
>> - * view is taken.
>> - */
>> - rxtx_gap = ((dws->rx_end - dws->rx) - (dws->tx_end - dws->tx))
>> - / dws->n_bytes;
>> -
>> - return min3(tx_left, tx_room, (u32) (dws->fifo_len - rxtx_gap));
>> -}
>> -
>> -/* Return the max entries we should read out of rx fifo */
>> -static inline u32 rx_max(struct dw_spi *dws)
>> -{
>> - u32 rx_left = (dws->rx_end - dws->rx) / dws->n_bytes;
>> -
>> - return min(rx_left, (u32)dw_readw(dws, rxflr));
>> -}
>> -
>> -static void dw_writer(struct dw_spi *dws)
>> -{
>> - u32 max = tx_max(dws);
>> - u16 txw = 0;
>> -
>> - while (max--) {
>> - /* Set the tx word if the transfer's original "tx" is not null */
>> - if (dws->tx_end - dws->len) {
>> - if (dws->n_bytes == 1)
>> - txw = *(u8 *)(dws->tx);
>> - else
>> - txw = *(u16 *)(dws->tx);
>> - }
>> - dw_writew(dws, dr, txw);
>> - dws->tx += dws->n_bytes;
>> - }
>> -}
>> -
>> -static void dw_reader(struct dw_spi *dws)
>> -{
>> - u32 max = rx_max(dws);
>> - u16 rxw;
>> -
>> - while (max--) {
>> - rxw = dw_readw(dws, dr);
>> - /* Care rx only if the transfer's original "rx" is not null */
>> - if (dws->rx_end - dws->len) {
>> - if (dws->n_bytes == 1)
>> - *(u8 *)(dws->rx) = rxw;
>> - else
>> - *(u16 *)(dws->rx) = rxw;
>> - }
>> - dws->rx += dws->n_bytes;
>> - }
>> -}
>> -
>> -static void *next_transfer(struct dw_spi *dws)
>> -{
>> - struct spi_message *msg = dws->cur_msg;
>> - struct spi_transfer *trans = dws->cur_transfer;
>> -
>> - /* Move to next transfer */
>> - if (trans->transfer_list.next !=&msg->transfers) {
>> - dws->cur_transfer =
>> - list_entry(trans->transfer_list.next,
>> - struct spi_transfer,
>> - transfer_list);
>> - return RUNNING_STATE;
>> - } else
>> - return DONE_STATE;
>> -}
>> -
>> -/*
>> - * Note: first step is the protocol driver prepares
>> - * a dma-capable memory, and this func just need translate
>> - * the virt addr to physical
>> - */
>> -static int map_dma_buffers(struct dw_spi *dws)
>> -{
>> - if (!dws->cur_msg->is_dma_mapped
>> - || !dws->dma_inited
>> - || !dws->cur_chip->enable_dma
>> - || !dws->dma_ops)
>> - return 0;
>> -
>> - if (dws->cur_transfer->tx_dma)
>> - dws->tx_dma = dws->cur_transfer->tx_dma;
>> -
>> - if (dws->cur_transfer->rx_dma)
>> - dws->rx_dma = dws->cur_transfer->rx_dma;
>> -
>> - return 1;
>> -}
>> -
>> -/* Caller already set message->status; dma and pio irqs are blocked */
>> -static void giveback(struct dw_spi *dws)
>> -{
>> - struct spi_transfer *last_transfer;
>> - unsigned long flags;
>> - struct spi_message *msg;
>> -
>> - spin_lock_irqsave(&dws->lock, flags);
>> - msg = dws->cur_msg;
>> - dws->cur_msg = NULL;
>> - dws->cur_transfer = NULL;
>> - dws->prev_chip = dws->cur_chip;
>> - dws->cur_chip = NULL;
>> - dws->dma_mapped = 0;
>> - queue_work(dws->workqueue,&dws->pump_messages);
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> -
>> - last_transfer = list_entry(msg->transfers.prev,
>> - struct spi_transfer,
>> - transfer_list);
>> -
>> - if (!last_transfer->cs_change&& dws->cs_control)
>> - dws->cs_control(MRST_SPI_DEASSERT);
>> -
>> - msg->state = NULL;
>> - if (msg->complete)
>> - msg->complete(msg->context);
>> -}
>> -
>> -static void int_error_stop(struct dw_spi *dws, const char *msg)
>> -{
>> - /* Stop the hw */
>> - spi_enable_chip(dws, 0);
>> -
>> - dev_err(&dws->master->dev, "%s\n", msg);
>> - dws->cur_msg->state = ERROR_STATE;
>> - tasklet_schedule(&dws->pump_transfers);
>> -}
>> -
>> -void dw_spi_xfer_done(struct dw_spi *dws)
>> -{
>> - /* Update total byte transferred return count actual bytes read */
>> - dws->cur_msg->actual_length += dws->len;
>> -
>> - /* Move to next transfer */
>> - dws->cur_msg->state = next_transfer(dws);
>> -
>> - /* Handle end of message */
>> - if (dws->cur_msg->state == DONE_STATE) {
>> - dws->cur_msg->status = 0;
>> - giveback(dws);
>> - } else
>> - tasklet_schedule(&dws->pump_transfers);
>> -}
>> -EXPORT_SYMBOL_GPL(dw_spi_xfer_done);
>> -
>> -static irqreturn_t interrupt_transfer(struct dw_spi *dws)
>> -{
>> - u16 irq_status = dw_readw(dws, isr);
>> -
>> - /* Error handling */
>> - if (irq_status& (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) {
>> - dw_readw(dws, txoicr);
>> - dw_readw(dws, rxoicr);
>> - dw_readw(dws, rxuicr);
>> - int_error_stop(dws, "interrupt_transfer: fifo overrun/underrun");
>> - return IRQ_HANDLED;
>> - }
>> -
>> - dw_reader(dws);
>> - if (dws->rx_end == dws->rx) {
>> - spi_mask_intr(dws, SPI_INT_TXEI);
>> - dw_spi_xfer_done(dws);
>> - return IRQ_HANDLED;
>> - }
>> - if (irq_status& SPI_INT_TXEI) {
>> - spi_mask_intr(dws, SPI_INT_TXEI);
>> - dw_writer(dws);
>> - /* Enable TX irq always, it will be disabled when RX finished */
>> - spi_umask_intr(dws, SPI_INT_TXEI);
>> - }
>> -
>> - return IRQ_HANDLED;
>> -}
>> -
>> -static irqreturn_t dw_spi_irq(int irq, void *dev_id)
>> -{
>> - struct dw_spi *dws = dev_id;
>> - u16 irq_status = dw_readw(dws, isr)& 0x3f;
>> -
>> - if (!irq_status)
>> - return IRQ_NONE;
>> -
>> - if (!dws->cur_msg) {
>> - spi_mask_intr(dws, SPI_INT_TXEI);
>> - return IRQ_HANDLED;
>> - }
>> -
>> - return dws->transfer_handler(dws);
>> -}
>> -
>> -/* Must be called inside pump_transfers() */
>> -static void poll_transfer(struct dw_spi *dws)
>> -{
>> - do {
>> - dw_writer(dws);
>> - dw_reader(dws);
>> - cpu_relax();
>> - } while (dws->rx_end> dws->rx);
>> -
>> - dw_spi_xfer_done(dws);
>> -}
>> -
>> -static void pump_transfers(unsigned long data)
>> -{
>> - struct dw_spi *dws = (struct dw_spi *)data;
>> - struct spi_message *message = NULL;
>> - struct spi_transfer *transfer = NULL;
>> - struct spi_transfer *previous = NULL;
>> - struct spi_device *spi = NULL;
>> - struct chip_data *chip = NULL;
>> - u8 bits = 0;
>> - u8 imask = 0;
>> - u8 cs_change = 0;
>> - u16 txint_level = 0;
>> - u16 clk_div = 0;
>> - u32 speed = 0;
>> - u32 cr0 = 0;
>> -
>> - /* Get current state information */
>> - message = dws->cur_msg;
>> - transfer = dws->cur_transfer;
>> - chip = dws->cur_chip;
>> - spi = message->spi;
>> -
>> - if (unlikely(!chip->clk_div))
>> - chip->clk_div = dws->max_freq / chip->speed_hz;
>> -
>> - if (message->state == ERROR_STATE) {
>> - message->status = -EIO;
>> - goto early_exit;
>> - }
>> -
>> - /* Handle end of message */
>> - if (message->state == DONE_STATE) {
>> - message->status = 0;
>> - goto early_exit;
>> - }
>> -
>> - /* Delay if requested at end of transfer*/
>> - if (message->state == RUNNING_STATE) {
>> - previous = list_entry(transfer->transfer_list.prev,
>> - struct spi_transfer,
>> - transfer_list);
>> - if (previous->delay_usecs)
>> - udelay(previous->delay_usecs);
>> - }
>> -
>> - dws->n_bytes = chip->n_bytes;
>> - dws->dma_width = chip->dma_width;
>> - dws->cs_control = chip->cs_control;
>> -
>> - dws->rx_dma = transfer->rx_dma;
>> - dws->tx_dma = transfer->tx_dma;
>> - dws->tx = (void *)transfer->tx_buf;
>> - dws->tx_end = dws->tx + transfer->len;
>> - dws->rx = transfer->rx_buf;
>> - dws->rx_end = dws->rx + transfer->len;
>> - dws->cs_change = transfer->cs_change;
>> - dws->len = dws->cur_transfer->len;
>> - if (chip != dws->prev_chip)
>> - cs_change = 1;
>> -
>> - cr0 = chip->cr0;
>> -
>> - /* Handle per transfer options for bpw and speed */
>> - if (transfer->speed_hz) {
>> - speed = chip->speed_hz;
>> -
>> - if (transfer->speed_hz != speed) {
>> - speed = transfer->speed_hz;
>> - if (speed> dws->max_freq) {
>> - printk(KERN_ERR "MRST SPI0: unsupported"
>> - "freq: %dHz\n", speed);
>> - message->status = -EIO;
>> - goto early_exit;
>> - }
>> -
>> - /* clk_div doesn't support odd number */
>> - clk_div = dws->max_freq / speed;
>> - clk_div = (clk_div + 1)& 0xfffe;
>> -
>> - chip->speed_hz = speed;
>> - chip->clk_div = clk_div;
>> - }
>> - }
>> - if (transfer->bits_per_word) {
>> - bits = transfer->bits_per_word;
>> -
>> - switch (bits) {
>> - case 8:
>> - case 16:
>> - dws->n_bytes = dws->dma_width = bits>> 3;
>> - break;
>> - default:
>> - printk(KERN_ERR "MRST SPI0: unsupported bits:"
>> - "%db\n", bits);
>> - message->status = -EIO;
>> - goto early_exit;
>> - }
>> -
>> - cr0 = (bits - 1)
>> - | (chip->type<< SPI_FRF_OFFSET)
>> - | (spi->mode<< SPI_MODE_OFFSET)
>> - | (chip->tmode<< SPI_TMOD_OFFSET);
>> - }
>> - message->state = RUNNING_STATE;
>> -
>> - /*
>> - * Adjust transfer mode if necessary. Requires platform dependent
>> - * chipselect mechanism.
>> - */
>> - if (dws->cs_control) {
>> - if (dws->rx&& dws->tx)
>> - chip->tmode = SPI_TMOD_TR;
>> - else if (dws->rx)
>> - chip->tmode = SPI_TMOD_RO;
>> - else
>> - chip->tmode = SPI_TMOD_TO;
>> -
>> - cr0&= ~SPI_TMOD_MASK;
>> - cr0 |= (chip->tmode<< SPI_TMOD_OFFSET);
>> - }
>> -
>> - /* Check if current transfer is a DMA transaction */
>> - dws->dma_mapped = map_dma_buffers(dws);
>> -
>> - /*
>> - * Interrupt mode
>> - * we only need set the TXEI IRQ, as TX/RX always happen syncronizely
>> - */
>> - if (!dws->dma_mapped&& !chip->poll_mode) {
>> - int templen = dws->len / dws->n_bytes;
>> - txint_level = dws->fifo_len / 2;
>> - txint_level = (templen> txint_level) ? txint_level : templen;
>> -
>> - imask |= SPI_INT_TXEI | SPI_INT_TXOI | SPI_INT_RXUI | SPI_INT_RXOI;
>> - dws->transfer_handler = interrupt_transfer;
>> - }
>> -
>> - /*
>> - * Reprogram registers only if
>> - * 1. chip select changes
>> - * 2. clk_div is changed
>> - * 3. control value changes
>> - */
>> - if (dw_readw(dws, ctrl0) != cr0 || cs_change || clk_div || imask) {
>> - spi_enable_chip(dws, 0);
>> -
>> - if (dw_readw(dws, ctrl0) != cr0)
>> - dw_writew(dws, ctrl0, cr0);
>> -
>> - spi_set_clk(dws, clk_div ? clk_div : chip->clk_div);
>> - spi_chip_sel(dws, spi->chip_select);
>> -
>> - /* Set the interrupt mask, for poll mode just disable all int */
>> - spi_mask_intr(dws, 0xff);
>> - if (imask)
>> - spi_umask_intr(dws, imask);
>> - if (txint_level)
>> - dw_writew(dws, txfltr, txint_level);
>> -
>> - spi_enable_chip(dws, 1);
>> - if (cs_change)
>> - dws->prev_chip = chip;
>> - }
>> -
>> - if (dws->dma_mapped)
>> - dws->dma_ops->dma_transfer(dws, cs_change);
>> -
>> - if (chip->poll_mode)
>> - poll_transfer(dws);
>> -
>> - return;
>> -
>> -early_exit:
>> - giveback(dws);
>> - return;
>> -}
>> -
>> -static void pump_messages(struct work_struct *work)
>> -{
>> - struct dw_spi *dws =
>> - container_of(work, struct dw_spi, pump_messages);
>> - unsigned long flags;
>> -
>> - /* Lock queue and check for queue work */
>> - spin_lock_irqsave(&dws->lock, flags);
>> - if (list_empty(&dws->queue) || dws->run == QUEUE_STOPPED) {
>> - dws->busy = 0;
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - return;
>> - }
>> -
>> - /* Make sure we are not already running a message */
>> - if (dws->cur_msg) {
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - return;
>> - }
>> -
>> - /* Extract head of queue */
>> - dws->cur_msg = list_entry(dws->queue.next, struct spi_message, queue);
>> - list_del_init(&dws->cur_msg->queue);
>> -
>> - /* Initial message state*/
>> - dws->cur_msg->state = START_STATE;
>> - dws->cur_transfer = list_entry(dws->cur_msg->transfers.next,
>> - struct spi_transfer,
>> - transfer_list);
>> - dws->cur_chip = spi_get_ctldata(dws->cur_msg->spi);
>> -
>> - /* Mark as busy and launch transfers */
>> - tasklet_schedule(&dws->pump_transfers);
>> -
>> - dws->busy = 1;
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> -}
>> -
>> -/* spi_device use this to queue in their spi_msg */
>> -static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg)
>> -{
>> - struct dw_spi *dws = spi_master_get_devdata(spi->master);
>> - unsigned long flags;
>> -
>> - spin_lock_irqsave(&dws->lock, flags);
>> -
>> - if (dws->run == QUEUE_STOPPED) {
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - return -ESHUTDOWN;
>> - }
>> -
>> - msg->actual_length = 0;
>> - msg->status = -EINPROGRESS;
>> - msg->state = START_STATE;
>> -
>> - list_add_tail(&msg->queue,&dws->queue);
>> -
>> - if (dws->run == QUEUE_RUNNING&& !dws->busy) {
>> -
>> - if (dws->cur_transfer || dws->cur_msg)
>> - queue_work(dws->workqueue,
>> - &dws->pump_messages);
>> - else {
>> - /* If no other data transaction in air, just go */
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - pump_messages(&dws->pump_messages);
>> - return 0;
>> - }
>> - }
>> -
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - return 0;
>> -}
>> -
>> -/* This may be called twice for each spi dev */
>> -static int dw_spi_setup(struct spi_device *spi)
>> -{
>> - struct dw_spi_chip *chip_info = NULL;
>> - struct chip_data *chip;
>> -
>> - if (spi->bits_per_word != 8&& spi->bits_per_word != 16)
>> - return -EINVAL;
>> -
>> - /* Only alloc on first setup */
>> - chip = spi_get_ctldata(spi);
>> - if (!chip) {
>> - chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
>> - if (!chip)
>> - return -ENOMEM;
>> - }
>> -
>> - /*
>> - * Protocol drivers may change the chip settings, so...
>> - * if chip_info exists, use it
>> - */
>> - chip_info = spi->controller_data;
>> -
>> - /* chip_info doesn't always exist */
>> - if (chip_info) {
>> - if (chip_info->cs_control)
>> - chip->cs_control = chip_info->cs_control;
>> -
>> - chip->poll_mode = chip_info->poll_mode;
>> - chip->type = chip_info->type;
>> -
>> - chip->rx_threshold = 0;
>> - chip->tx_threshold = 0;
>> -
>> - chip->enable_dma = chip_info->enable_dma;
>> - }
>> -
>> - if (spi->bits_per_word<= 8) {
>> - chip->n_bytes = 1;
>> - chip->dma_width = 1;
>> - } else if (spi->bits_per_word<= 16) {
>> - chip->n_bytes = 2;
>> - chip->dma_width = 2;
>> - } else {
>> - /* Never take>16b case for MRST SPIC */
>> - dev_err(&spi->dev, "invalid wordsize\n");
>> - return -EINVAL;
>> - }
>> - chip->bits_per_word = spi->bits_per_word;
>> -
>> - if (!spi->max_speed_hz) {
>> - dev_err(&spi->dev, "No max speed HZ parameter\n");
>> - return -EINVAL;
>> - }
>> - chip->speed_hz = spi->max_speed_hz;
>> -
>> - chip->tmode = 0; /* Tx& Rx */
>> - /* Default SPI mode is SCPOL = 0, SCPH = 0 */
>> - chip->cr0 = (chip->bits_per_word - 1)
>> - | (chip->type<< SPI_FRF_OFFSET)
>> - | (spi->mode<< SPI_MODE_OFFSET)
>> - | (chip->tmode<< SPI_TMOD_OFFSET);
>> -
>> - spi_set_ctldata(spi, chip);
>> - return 0;
>> -}
>> -
>> -static void dw_spi_cleanup(struct spi_device *spi)
>> -{
>> - struct chip_data *chip = spi_get_ctldata(spi);
>> - kfree(chip);
>> -}
>> -
>> -static int __devinit init_queue(struct dw_spi *dws)
>> -{
>> - INIT_LIST_HEAD(&dws->queue);
>> - spin_lock_init(&dws->lock);
>> -
>> - dws->run = QUEUE_STOPPED;
>> - dws->busy = 0;
>> -
>> - tasklet_init(&dws->pump_transfers,
>> - pump_transfers, (unsigned long)dws);
>> -
>> - INIT_WORK(&dws->pump_messages, pump_messages);
>> - dws->workqueue = create_singlethread_workqueue(
>> - dev_name(dws->master->dev.parent));
>> - if (dws->workqueue == NULL)
>> - return -EBUSY;
>> -
>> - return 0;
>> -}
>> -
>> -static int start_queue(struct dw_spi *dws)
>> -{
>> - unsigned long flags;
>> -
>> - spin_lock_irqsave(&dws->lock, flags);
>> -
>> - if (dws->run == QUEUE_RUNNING || dws->busy) {
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - return -EBUSY;
>> - }
>> -
>> - dws->run = QUEUE_RUNNING;
>> - dws->cur_msg = NULL;
>> - dws->cur_transfer = NULL;
>> - dws->cur_chip = NULL;
>> - dws->prev_chip = NULL;
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> -
>> - queue_work(dws->workqueue,&dws->pump_messages);
>> -
>> - return 0;
>> -}
>> -
>> -static int stop_queue(struct dw_spi *dws)
>> -{
>> - unsigned long flags;
>> - unsigned limit = 50;
>> - int status = 0;
>> -
>> - spin_lock_irqsave(&dws->lock, flags);
>> - dws->run = QUEUE_STOPPED;
>> - while ((!list_empty(&dws->queue) || dws->busy)&& limit--) {
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> - msleep(10);
>> - spin_lock_irqsave(&dws->lock, flags);
>> - }
>> -
>> - if (!list_empty(&dws->queue) || dws->busy)
>> - status = -EBUSY;
>> - spin_unlock_irqrestore(&dws->lock, flags);
>> -
>> - return status;
>> -}
>> -
>> -static int destroy_queue(struct dw_spi *dws)
>> -{
>> - int status;
>> -
>> - status = stop_queue(dws);
>> - if (status != 0)
>> - return status;
>> - destroy_workqueue(dws->workqueue);
>> - return 0;
>> -}
>> -
>> -/* Restart the controller, disable all interrupts, clean rx fifo */
>> -static void spi_hw_init(struct dw_spi *dws)
>> -{
>> - spi_enable_chip(dws, 0);
>> - spi_mask_intr(dws, 0xff);
>> - spi_enable_chip(dws, 1);
>> -
>> - /*
>> - * Try to detect the FIFO depth if not set by interface driver,
>> - * the depth could be from 2 to 256 from HW spec
>> - */
>> - if (!dws->fifo_len) {
>> - u32 fifo;
>> - for (fifo = 2; fifo<= 257; fifo++) {
>> - dw_writew(dws, txfltr, fifo);
>> - if (fifo != dw_readw(dws, txfltr))
>> - break;
>> - }
>> -
>> - dws->fifo_len = (fifo == 257) ? 0 : fifo;
>> - dw_writew(dws, txfltr, 0);
>> - }
>> -}
>> -
>> -int __devinit dw_spi_add_host(struct dw_spi *dws)
>> -{
>> - struct spi_master *master;
>> - int ret;
>> -
>> - BUG_ON(dws == NULL);
>> -
>> - master = spi_alloc_master(dws->parent_dev, 0);
>> - if (!master) {
>> - ret = -ENOMEM;
>> - goto exit;
>> - }
>> -
>> - dws->master = master;
>> - dws->type = SSI_MOTO_SPI;
>> - dws->prev_chip = NULL;
>> - dws->dma_inited = 0;
>> - dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60);
>> -
>> - ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED,
>> - "dw_spi", dws);
>> - if (ret< 0) {
>> - dev_err(&master->dev, "can not get IRQ\n");
>> - goto err_free_master;
>> - }
>> -
>> - master->mode_bits = SPI_CPOL | SPI_CPHA;
>> - master->bus_num = dws->bus_num;
>> - master->num_chipselect = dws->num_cs;
>> - master->cleanup = dw_spi_cleanup;
>> - master->setup = dw_spi_setup;
>> - master->transfer = dw_spi_transfer;
>> -
>> - /* Basic HW init */
>> - spi_hw_init(dws);
>> -
>> - if (dws->dma_ops&& dws->dma_ops->dma_init) {
>> - ret = dws->dma_ops->dma_init(dws);
>> - if (ret) {
>> - dev_warn(&master->dev, "DMA init failed\n");
>> - dws->dma_inited = 0;
>> - }
>> - }
>> -
>> - /* Initial and start queue */
>> - ret = init_queue(dws);
>> - if (ret) {
>> - dev_err(&master->dev, "problem initializing queue\n");
>> - goto err_diable_hw;
>> - }
>> - ret = start_queue(dws);
>> - if (ret) {
>> - dev_err(&master->dev, "problem starting queue\n");
>> - goto err_diable_hw;
>> - }
>> -
>> - spi_master_set_devdata(master, dws);
>> - ret = spi_register_master(master);
>> - if (ret) {
>> - dev_err(&master->dev, "problem registering spi master\n");
>> - goto err_queue_alloc;
>> - }
>> -
>> - mrst_spi_debugfs_init(dws);
>> - return 0;
>> -
>> -err_queue_alloc:
>> - destroy_queue(dws);
>> - if (dws->dma_ops&& dws->dma_ops->dma_exit)
>> - dws->dma_ops->dma_exit(dws);
>> -err_diable_hw:
>> - spi_enable_chip(dws, 0);
>> - free_irq(dws->irq, dws);
>> -err_free_master:
>> - spi_master_put(master);
>> -exit:
>> - return ret;
>> -}
>> -EXPORT_SYMBOL_GPL(dw_spi_add_host);
>> -
>> -void __devexit dw_spi_remove_host(struct dw_spi *dws)
>> -{
>> - int status = 0;
>> -
>> - if (!dws)
>> - return;
>> - mrst_spi_debugfs_remove(dws);
>> -
>> - /* Remove the queue */
>> - status = destroy_queue(dws);
>> - if (status != 0)
>> - dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not "
>> - "complete, message memory not freed\n");
>> -
>> - if (dws->dma_ops&& dws->dma_ops->dma_exit)
>> - dws->dma_ops->dma_exit(dws);
>> - spi_enable_chip(dws, 0);
>> - /* Disable clk */
>> - spi_set_clk(dws, 0);
>> - free_irq(dws->irq, dws);
>> -
>> - /* Disconnect from the SPI framework */
>> - spi_unregister_master(dws->master);
>> -}
>> -EXPORT_SYMBOL_GPL(dw_spi_remove_host);
>> -
>> -int dw_spi_suspend_host(struct dw_spi *dws)
>> -{
>> - int ret = 0;
>> -
>> - ret = stop_queue(dws);
>> - if (ret)
>> - return ret;
>> - spi_enable_chip(dws, 0);
>> - spi_set_clk(dws, 0);
>> - return ret;
>> -}
>> -EXPORT_SYMBOL_GPL(dw_spi_suspend_host);
>> -
>> -int dw_spi_resume_host(struct dw_spi *dws)
>> -{
>> - int ret;
>> -
>> - spi_hw_init(dws);
>> - ret = start_queue(dws);
>> - if (ret)
>> - dev_err(&dws->master->dev, "fail to start queue (%d)\n", ret);
>> - return ret;
>> -}
>> -EXPORT_SYMBOL_GPL(dw_spi_resume_host);
>> -
>> -MODULE_AUTHOR("Feng Tang<feng.tang@...el.com>");
>> -MODULE_DESCRIPTION("Driver for DesignWare SPI controller core");
>> -MODULE_LICENSE("GPL v2");
>> +/*
>> + * dw_spi.c - Designware SPI core controller driver
>
> drop the filename. It's incorrect, and not useful. The useful bit is
> the driver description.
>
OK
>> + *
>> + * Copyright (c) 2009, Intel Corporation.
>> + *
>> + * This program is free software; you can redistribute it and/or modify it
>> + * under the terms and conditions of the GNU General Public License,
>> + * version 2, as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope it will be useful, but WITHOUT
>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
>> + * more details.
>> + *
>> + * You should have received a copy of the GNU General Public License along with
>> + * this program; if not, write to the Free Software Foundation, Inc.,
>> + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
>> + */
>> +
>> +#include<linux/dma-mapping.h>
>> +#include<linux/interrupt.h>
>> +#include<linux/highmem.h>
>> +#include<linux/delay.h>
>> +#include<linux/slab.h>
>> +#include<linux/spi/spi.h>
>> +
>> +#include "spi-dw.h"
>> +
>> +#ifdef CONFIG_DEBUG_FS
>> +#include<linux/debugfs.h>
>> +#endif
>> +
>> +
>> +#define QUEUE_RUNNING 0
>> +#define QUEUE_STOPPED 1
>> +
>> +
>> +/* Slave spi_dev related */
>> +struct chip_data {
>> + struct spi_device *spi_dev;
>> + u32 cr0;
>> + u32 cs; /* chip select pin */
>> + u32 n_bytes; /* current is a 1/2/4 byte op */
>> + u32 type; /* SPI/SSP/MicroWire */
>> +
>> + u32 dma_width;
>> + u32 enable_dma;
>> + u32 bits_per_word;
>> + u32 clk_div; /* baud rate divider */
>> + u32 speed_hz; /* baud rate */
>> +};
>> +
>> +#ifdef CONFIG_DEBUG_FS
>> +static int spi_show_regs_open(struct inode *inode, struct file *file)
>> +{
>> + file->private_data = inode->i_private;
>> + return 0;
>> +}
>> +
>> +#define SPI_REGS_BUFSIZE 1024
>> +static ssize_t spi_show_regs(struct file *file, char __user *user_buf,
>> + size_t count, loff_t *ppos)
>> +{
>> + struct dw_spi *dws;
>> + char *buf;
>> + u32 len = 0;
>> + ssize_t ret;
>> +
>> + dws = file->private_data;
>> +
>> + buf = kzalloc(SPI_REGS_BUFSIZE, GFP_KERNEL);
>> + if (!buf)
>> + return 0;
>> +
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "MRST SPI0 registers:\n");
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "=================================\n");
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "CTRL0: \t\t0x%08x\n", dw_readl(dws, ctrl0));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "CTRL1: \t\t0x%08x\n", dw_readl(dws, ctrl1));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "SSIENR: \t0x%08x\n", dw_readl(dws, ssienr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "SER: \t\t0x%08x\n", dw_readl(dws, ser));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "BAUDR: \t\t0x%08x\n", dw_readl(dws, baudr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "TXFTLR: \t0x%08x\n", dw_readl(dws, txfltr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "RXFTLR: \t0x%08x\n", dw_readl(dws, rxfltr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "TXFLR: \t\t0x%08x\n", dw_readl(dws, txflr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "RXFLR: \t\t0x%08x\n", dw_readl(dws, rxflr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "SR: \t\t0x%08x\n", dw_readl(dws, sr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "IMR: \t\t0x%08x\n", dw_readl(dws, imr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "ISR: \t\t0x%08x\n", dw_readl(dws, isr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "DMACR: \t\t0x%08x\n", dw_readl(dws, dmacr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "DMATDLR: \t0x%08x\n", dw_readl(dws, dmatdlr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "DMARDLR: \t0x%08x\n", dw_readl(dws, dmardlr));
>> + len += snprintf(buf + len, SPI_REGS_BUFSIZE - len,
>> + "=================================\n");
>> +
>> + ret = simple_read_from_buffer(user_buf, count, ppos, buf, len);
>> + kfree(buf);
>> + return ret;
>> +}
>> +
>> +static const struct file_operations mrst_spi_regs_ops = {
>> + .owner = THIS_MODULE,
>> + .open = spi_show_regs_open,
>> + .read = spi_show_regs,
>> + .llseek = default_llseek,
>> +};
>> +
>> +static int mrst_spi_debugfs_init(struct dw_spi *dws)
>> +{
>> + dws->debugfs = debugfs_create_dir("mrst_spi", NULL);
>> + if (!dws->debugfs)
>> + return -ENOMEM;
>> +
>> + debugfs_create_file("registers", S_IFREG | S_IRUGO,
>> + dws->debugfs, (void *)dws,&mrst_spi_regs_ops);
>> + return 0;
>> +}
>> +
>> +static void mrst_spi_debugfs_remove(struct dw_spi *dws)
>> +{
>> + if (dws->debugfs)
>> + debugfs_remove_recursive(dws->debugfs);
>> +}
>> +
>> +#else
>> +static inline int mrst_spi_debugfs_init(struct dw_spi *dws)
>> +{
>> + return 0;
>> +}
>> +
>> +static inline void mrst_spi_debugfs_remove(struct dw_spi *dws)
>> +{
>> +}
>> +#endif /* CONFIG_DEBUG_FS */
>> +
>> +static irqreturn_t dw_spi_irq(int irq, void *dev_id)
>> +{
>> + struct dw_spi *dws = dev_id;
>> + u16 irq_mask = 0x3f;
>> +
>> + dws->xfer.irq_status = dw_readw(dws, isr)& irq_mask;
>> +
>> + if (!dws->xfer.irq_status)
>> + return IRQ_NONE;
>> + if (dws->xfer.irq_status&
>> + (SPI_INT_TXOI | SPI_INT_RXOI | SPI_INT_RXUI)) {
>> + dw_readw(dws, txoicr);
>> + dw_readw(dws, rxoicr);
>> + dw_readw(dws, rxuicr);
>> + dws->xfer.err = -EIO;
>> + dw_spi_disable(dws);
>> + complete(&dws->xfer.complete);
>> + return IRQ_HANDLED;
>> + }
>> +
>> + /* disable interrupts */
>> + dw_spi_mask_intr(dws, irq_mask);
>> + return IRQ_WAKE_THREAD;
>> +}
>> +struct spi_message *get_message(struct dw_spi *dws)
>> +{
>> + struct spi_message *message = NULL;
>> + unsigned long flags;
>> +
>> + spin_lock_irqsave(&dws->lock, flags);
>> + if (!list_empty(&dws->queue)) {
>> + message = list_entry(dws->queue.next,
>> + struct spi_message, queue);
>> + list_del_init(&message->queue);
>> + }
>> + spin_unlock_irqrestore(&dws->lock, flags);
>> + return message;
>> +}
>> +static inline u32 tx_max(struct dw_spi *dws)
>> +{
>> + u32 tx_left, tx_room;
>> +
>> + tx_left = (dws->xfer.len - dws->xfer.sent) / dws->xfer.n_bytes;
>> + tx_room = (dws->fifo_len - dw_readw(dws, txflr));
>> +
>> + return min(tx_left, tx_room);
>> +}
>> +
>> +/* Return the max entries we should read out of rx fifo */
>> +static inline u32 rx_max(struct dw_spi *dws)
>> +{
>> + u32 rx_left = (dws->xfer.len - dws->xfer.rcvd) / dws->xfer.n_bytes;
>> + return min(rx_left, (u32)dw_readw(dws, rxflr));
>> +}
>> +
>> +static int transfer_setup(struct dw_spi *dws, struct chip_data *controller,
>> + struct spi_transfer *transfer, struct spi_message *msg)
>> +{
>> + int err = 0;
>> + u32 cr0 = controller->cr0;
>> + u32 clk_div;
>> +
>> + dws->xfer.tx_buf = transfer->tx_buf;
>> + dws->xfer.tx_dma = transfer->tx_dma;
>> + dws->xfer.rx_buf = transfer->rx_buf;
>> + dws->xfer.rx_dma = transfer->rx_dma;
>> +
>> + dws->xfer.len = transfer->len;
>> + dws->xfer.n_bytes = controller->n_bytes;
>> + dws->xfer.sent = 0;
>> + dws->xfer.rcvd = 0;
>> + dws->xfer.msg = msg;
>> + dws->xfer.err = 0;
>> + dws->xfer.irq_status = 0;
>> + INIT_COMPLETION(dws->xfer.complete);
>> +
>> + /* {tx, rx}_threshold should probably be a module param with
>> + * some reasonable default but these work for now.
>> + */
>> + dws->xfer.tx_threshold = 10;
>> + dws->xfer.rx_threshold = dws->xfer.tx_threshold - 1;
>> +
>> + /* we need to make the decsion about the type of transfer more
>> + * inteligently but this works for now
>> + */
>> + if (transfer->len> dws->fifo_len)
>> + dws->xfer.type = INT_XFER;
>> + else
>> + dws->xfer.type = PIO_XFER;
>> +
>> + if (controller->enable_dma&&
>> + msg->is_dma_mapped&&
>> + dws->dma_inited&&
>> + dws->dma_ops)
>> + dws->xfer.type = DMA_XFER;
>> +
>> + /* Setup the controller based on parameters in the transfer
>> + * each transfer can set the bit_per_word and the speed_hz to
>> + * change these values in the controller the controller MUST
>> + * be disabled
>> + */
>> + if (unlikely(!controller->clk_div)) {
>> + controller->clk_div = dws->max_freq / controller->speed_hz;
>> + controller->clk_div = (controller->clk_div + 1)& 0xfffe;
>> + dw_spi_set_clk(dws, controller->clk_div);
>> + dev_err(&dws->master->dev, "setting default clk_div");
>> + err = 1;
>> + }
>> +
>> + if (transfer->speed_hz) {
>> + if (transfer->speed_hz != controller->speed_hz) {
>> + if (transfer->speed_hz> dws->max_freq) {
>> + err = -EIO;
>> + goto out;
>> + }
>> +
>> + clk_div = dws->max_freq / transfer->speed_hz;
>> + clk_div = (clk_div + 1)& 0xfffe;
>> + controller->clk_div = clk_div;
>> + controller->speed_hz = transfer->speed_hz;
>> + err = 1;
>> + }
>> + }
>> +
>> + if (transfer->bits_per_word) {
>> + if (transfer->bits_per_word != 8&&
>> + transfer->bits_per_word != 16) {
>> + err = -EIO;
>> + goto out;
>> + }
>> + cr0&= ~SPI_DFS_MASK;
>> + cr0 |= transfer->bits_per_word - 1;
>> + err = 1;
>> + } else {
>> + cr0&= ~SPI_DFS_MASK;
>> + cr0 |= controller->spi_dev->bits_per_word - 1;
>> + }
>> +
>> + cr0&= ~SPI_MODE_MASK;
>> + cr0 |= (controller->spi_dev->mode<< SPI_MODE_OFFSET);
>> + controller->cr0 = cr0;
>> +
>> + if (err || dw_readw(dws, ctrl0) != cr0) {
>> + dw_spi_disable(dws);
>> + dw_spi_chip_sel(dws, controller->spi_dev->chip_select);
>> + dw_writew(dws, ctrl0, cr0);
>> + dw_spi_set_clk(dws, controller->clk_div);
>> + dw_spi_enable(dws);
>> + err = 0;
>> + }
>> +out:
>> + return err;
>> +}
>> +
>> +static void tx_fifo_fill(struct dw_spi *dws)
>> +{
>> + int room;
>> + u16 txw = 0;
>> + if (dws->xfer.sent< dws->xfer.len) {
>> + room = tx_max(dws);
>> + while (room--) {
>> + if (dws->xfer.tx_buf) {
>> + if (dws->xfer.n_bytes == 2)
>> + txw = *(u16 *)dws->xfer.tx_buf;
>> + else
>> + txw = *(u8 *)dws->xfer.tx_buf;
>> + dws->xfer.tx_buf += dws->xfer.n_bytes;
>> + }
>> + dw_writew(dws, dr, txw);
>> + dws->xfer.sent += dws->xfer.n_bytes;
>> + }
>> + }
>> +}
>> +
>> +
>> +static void rx_fifo_drain(struct dw_spi *dws)
>> +{
>> + u16 rx_val;
>> + int avail;
>> +
>> + if (dws->xfer.rcvd< dws->xfer.len) {
>> + avail = rx_max(dws);
>> + while (avail--) {
>> + rx_val = dw_readw(dws, dr);
>> + if (dws->xfer.rx_buf) {
>> + if (dws->xfer.n_bytes == 2)
>> + *(u16 *)(dws->xfer.rx_buf) =
>> + (u16)rx_val;
>> + else
>> + *dws->xfer.rx_buf = (u8)rx_val;
>> + dws->xfer.rx_buf += dws->xfer.n_bytes;
>> + }
>> + dws->xfer.rcvd += dws->xfer.n_bytes;
>> + }
>> + }
>> +}
>> +
>> +static inline void do_pio(struct dw_spi *dws)
>> +{
>> + while (dws->xfer.sent< dws->xfer.len ||
>> + dws->xfer.rcvd< dws->xfer.len) {
>> + tx_fifo_fill(dws);
>> + rx_fifo_drain(dws);
>> + cpu_relax();
>> + }
>> + complete(&dws->xfer.complete);
>> +}
>> +
>> +static irqreturn_t dw_spi_irq_thread_handler(int irq, void *dev_id)
>> +{
>> + struct dw_spi *dws = dev_id;
>> +
>> + if (dws->xfer.irq_status& SPI_INT_TXEI) {
>> + rx_fifo_drain(dws);
>> + tx_fifo_fill(dws);
>> + }
>> +
>> + if (dws->xfer.irq_status& SPI_INT_RXFI) {
>> + tx_fifo_fill(dws);
>> + rx_fifo_drain(dws);
>> + }
>> +
>> + if (dws->xfer.len == dws->xfer.rcvd&&
>> + dws->xfer.len == dws->xfer.sent) {
>> + complete(&dws->xfer.complete);
>> + goto out;
>> + }
>> +
>> + dw_spi_umask_intr(dws, SPI_INT_ALL);
>> +out:
>> + return IRQ_HANDLED;
>> +}
>> +
>> +static inline void do_int_xfer(struct dw_spi *dws)
>> +{
>> + dw_spi_disable(dws);
>> + dw_writew(dws, txfltr, dws->xfer.tx_threshold);
>> + dw_writew(dws, rxfltr, dws->xfer.rx_threshold);
>> + dw_spi_enable(dws);
>> + dw_readw(dws, icr);
>> + tx_fifo_fill(dws);
>> + dw_writew(dws, imr, SPI_INT_ALL);
>> +}
>> +
>> +static inline int do_transfer(struct dw_spi *dws)
>> +{
>> + switch (dws->xfer.type) {
>> + case PIO_XFER:
>> + do_pio(dws);
>> + break;
>> + case INT_XFER:
>> + do_int_xfer(dws);
>> + break;
>> + case DMA_XFER:
>> + dws->dma_ops->dma_transfer(dws);
>> + break;
>> + default:
>> + BUG();
>> + }
>> +
>> + wait_for_completion(&dws->xfer.complete);
>> +
>> +
>> + return dws->xfer.err;
>> +}
>> +
>> +static void drain_message_queue(struct dw_spi *dws)
>> +{
>> + struct spi_message *message;
>> +
>> + message = get_message(dws);
>> + while (message) {
>> + message->status = -ESHUTDOWN;
>> + message->complete(message->context);
>> + message = get_message(dws);
>> + }
>> +}
>> +
>> +static void pump_messages(struct work_struct *work)
>> +{
>> + struct dw_spi *dws =
>> + container_of(work, struct dw_spi, pump_messages);
>> + struct spi_transfer *transfer;
>> + struct spi_message *message;
>> + struct chip_data *controller;
>> + int err = 0;
>> +
>> +
>> + message = get_message(dws);
>> +
>> + while (message&& dws->run != QUEUE_STOPPED) {
>> + controller = spi_get_ctldata(message->spi);
>> + list_for_each_entry(transfer,&message->transfers,
>> + transfer_list){
>> +
>> + err = transfer_setup(dws, controller,
>> + transfer, message);
>> + if (err< 0) {
>> + dev_err(&dws->master->dev,
>> + "transfer_setup failed");
>> + dws->xfer.err = -EIO;
>> + break;
>> + }
>> +
>> + err = do_transfer(dws);
>> + if (err< 0) {
>> + dev_err(&dws->master->dev,
>> + "do_transfer failed");
>> + break;
>> + }
>> + message->actual_length += dws->xfer.len;
>> +
>> + if (transfer->delay_usecs)
>> + udelay(transfer->delay_usecs);
>> + }
>> +
>> + message->status = dws->xfer.err;
>> + message->complete(message->context);
>> + message = get_message(dws);
>> + }
>> + if (dws->run == QUEUE_STOPPED)
>> + drain_message_queue(dws);
>> +}
>> +
>> +/* spi_device use this to queue in their spi_msg */
>> +static int dw_spi_transfer(struct spi_device *spi, struct spi_message *msg)
>> +{
>> + struct dw_spi *dws = spi_master_get_devdata(spi->master);
>> + unsigned long flags;
>> +
>> +
>> + spin_lock_irqsave(&dws->lock, flags);
>> +
>> + msg->actual_length = 0;
>> + msg->status = -EINPROGRESS;
>> +
>> + list_add_tail(&msg->queue,&dws->queue);
>> +
>> + queue_work(dws->workqueue,
>> + &dws->pump_messages);
>> +
>> + spin_unlock_irqrestore(&dws->lock, flags);
>> +
>> + return 0;
>> +}
>> +
>> +/* This may be called twice for each spi dev */
>> +static int dw_spi_setup(struct spi_device *spi)
>> +{
>> + struct dw_spi_chip *chip_info = NULL;
>> + struct chip_data *chip;
>> +
>> + if (spi->bits_per_word != 8&& spi->bits_per_word != 16)
>> + return -EINVAL;
>> +
>> + if (!spi->max_speed_hz) {
>> + dev_err(&spi->dev, "No max speed HZ parameter\n");
>> + return -EINVAL;
>> + }
>> +
>> + /* Only alloc on first setup */
>> + chip = spi_get_ctldata(spi);
>> + if (!chip) {
>> + chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
>> + if (!chip)
>> + return -ENOMEM;
>> + }
>> + chip->spi_dev = spi;
>> +
>> + /*
>> + * Protocol drivers may change the chip settings, so...
>> + * if chip_info exists, use it
>> + */
>> + chip_info = spi->controller_data;
>> +
>> + /* chip_info doesn't always exist */
>> + if (chip_info) {
>> + chip->type = chip_info->type;
>> + chip->enable_dma = chip_info->enable_dma;
>> + }
>> +
>> + chip->bits_per_word = spi->bits_per_word;
>> + chip->n_bytes = chip->bits_per_word / 8;
>> + chip->dma_width = chip->bits_per_word / 8;
>> +
>> + chip->speed_hz = spi->max_speed_hz;
>> +
>> + /* Default SPI mode is SCPOL = 0, SCPH = 0 */
>> + chip->cr0 = (chip->bits_per_word - 1)
>> + | (chip->type<< SPI_FRF_OFFSET)
>> + | (spi->mode<< SPI_MODE_OFFSET);
>> +
>> + spi_set_ctldata(spi, chip);
>> + return 0;
>> +}
>> +
>> +static void dw_spi_cleanup(struct spi_device *spi)
>> +{
>> + struct chip_data *chip = spi_get_ctldata(spi);
>> + kfree(chip);
>> +}
>> +
>> +static int __devinit init_queue(struct dw_spi *dws)
>> +{
>> + INIT_LIST_HEAD(&dws->queue);
>> + spin_lock_init(&dws->lock);
>> +
>> + dws->run = QUEUE_STOPPED;
>> +
>> + INIT_WORK(&dws->pump_messages, pump_messages);
>> + dws->workqueue = create_singlethread_workqueue(
>> + dev_name(dws->master->dev.parent));
>> + if (dws->workqueue == NULL)
>> + return -EBUSY;
>> + dws->run = QUEUE_RUNNING;
>> + return 0;
>> +}
>> +
>> +
>> +int dw_spi_stop_queue(struct dw_spi *dws)
>> +{
>> + unsigned long flags;
>> + int status = 0;
>> +
>> + spin_lock_irqsave(&dws->lock, flags);
>> + dws->run = QUEUE_STOPPED;
>> +
>> + if (!list_empty(&dws->queue))
>> + status = -EBUSY;
>> + spin_unlock_irqrestore(&dws->lock, flags);
>> +
>> + return status;
>> +}
>> +EXPORT_SYMBOL_GPL(dw_spi_stop_queue);
>> +
>> +static int destroy_queue(struct dw_spi *dws)
>> +{
>> + int status;
>> +
>> + status = dw_spi_stop_queue(dws);
>> + if (status != 0)
>> + return status;
>> + destroy_workqueue(dws->workqueue);
>> + return 0;
>> +}
>> +
>> +/* Restart the controller, disable all interrupts, clean rx fifo */
>> +static void spi_hw_init(struct dw_spi *dws)
>> +{
>> + dw_spi_disable(dws);
>> + dw_spi_mask_intr(dws, 0xff);
>> + dw_readw(dws, icr);
>> + dw_spi_enable(dws);
>> +
>> + BUG_ON(!dws->fifo_len);
>> +}
>> +
>> +int __devinit dw_spi_add_host(struct dw_spi *dws)
>> +{
>> + struct spi_master *master;
>> + int ret;
>> +
>> + BUG_ON(dws == NULL);
>> +
>> + master = spi_alloc_master(dws->parent_dev, 0);
>> + if (!master) {
>> + ret = -ENOMEM;
>> + goto exit;
>> + }
>> +
>> + dws->master = master;
>> + dws->type = SSI_MOTO_SPI;
>> +
>> + init_completion(&dws->xfer.complete);
>> + dws->dma_inited = 0;
>> + /* Change to address of FIFO */
>> + dws->dma_addr = (dma_addr_t)(dws->paddr + 0x60);
>> +
>> + ret = request_threaded_irq(dws->irq, dw_spi_irq,
>> + dw_spi_irq_thread_handler,
>> + IRQF_SHARED, "dw_spi", dws);
>> + if (ret< 0) {
>> + dev_err(&master->dev, "can not get IRQ\n");
>> + goto err_free_master;
>> + }
>> +
>> + master->mode_bits = SPI_CPOL | SPI_CPHA;
>> + master->bus_num = dws->bus_num;
>> + master->num_chipselect = dws->num_cs;
>> + master->cleanup = dw_spi_cleanup;
>> + master->setup = dw_spi_setup;
>> + master->transfer = dw_spi_transfer;
>> +
>> + /* Basic HW init */
>> + spi_hw_init(dws);
>> +
>> + if (dws->dma_ops&& dws->dma_ops->dma_init) {
>> + ret = dws->dma_ops->dma_init(dws);
>> + if (ret) {
>> + dev_warn(&master->dev, "DMA init failed\n");
>> + dws->dma_inited = 0;
>> + }
>> + }
>> +
>> + /* Initial and start queue */
>> + ret = init_queue(dws);
>> + if (ret) {
>> + dev_err(&master->dev, "problem initializing queue\n");
>> + goto err_diable_hw;
>> + }
>> +
>> + spi_master_set_devdata(master, dws);
>> + ret = spi_register_master(master);
>> + if (ret) {
>> + dev_err(&master->dev, "problem registering spi master\n");
>> + goto err_queue_alloc;
>> + }
>> +
>> + mrst_spi_debugfs_init(dws);
>> + return 0;
>> +
>> +err_queue_alloc:
>> + destroy_queue(dws);
>> + if (dws->dma_ops&& dws->dma_ops->dma_exit)
>> + dws->dma_ops->dma_exit(dws);
>> +err_diable_hw:
>> + dw_spi_disable(dws);
>> + free_irq(dws->irq, dws);
>> +err_free_master:
>> + spi_master_put(master);
>> +exit:
>> + return ret;
>> +}
>> +EXPORT_SYMBOL_GPL(dw_spi_add_host);
>> +
>> +void __devexit dw_spi_remove_host(struct dw_spi *dws)
>> +{
>> + int status = 0;
>> +
>> + if (!dws)
>> + return;
>> + mrst_spi_debugfs_remove(dws);
>> +
>> + /* Remove the queue */
>> + status = destroy_queue(dws);
>> + if (status != 0)
>> + dev_err(&dws->master->dev, "dw_spi_remove: workqueue will not "
>> + "complete, message memory not freed\n");
>> +
>> + if (dws->dma_ops&& dws->dma_ops->dma_exit)
>> + dws->dma_ops->dma_exit(dws);
>> + dw_spi_disable(dws);
>> + dw_readw(dws, icr);
>> + free_irq(dws->irq, dws);
>> +
>> + /* Disconnect from the SPI framework */
>> + spi_unregister_master(dws->master);
>> +}
>> +EXPORT_SYMBOL_GPL(dw_spi_remove_host);
>> +
>> +int dw_spi_suspend_host(struct dw_spi *dws)
>> +{
>> + int ret = 0;
>> +
>> + ret = dw_spi_stop_queue(dws);
>> + if (ret)
>> + return ret;
>> + dw_spi_disable(dws);
>> + return ret;
>> +}
>> +EXPORT_SYMBOL_GPL(dw_spi_suspend_host);
>> +
>> +int dw_spi_resume_host(struct dw_spi *dws)
>> +{
>> + spi_hw_init(dws);
>> + dws->run = QUEUE_RUNNING;
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(dw_spi_resume_host);
>> +
>> +MODULE_AUTHOR("Feng Tang<feng.tang@...el.com>");
>> +MODULE_DESCRIPTION("Driver for DesignWare SPI controller core");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h
>> index 97baff6..b016b85 100644
>> --- a/drivers/spi/spi-dw.h
>> +++ b/drivers/spi/spi-dw.h
>> @@ -7,6 +7,7 @@
>>
>> /* Bit fields in CTRLR0 */
>> #define SPI_DFS_OFFSET 0
>> +#define SPI_DFS_MASK 0xf
>>
>> #define SPI_FRF_OFFSET 4
>> #define SPI_FRF_SPI 0x0
>> @@ -17,6 +18,7 @@
>> #define SPI_MODE_OFFSET 6
>> #define SPI_SCPH_OFFSET 6
>> #define SPI_SCOL_OFFSET 7
>> +#define SPI_MODE_MASK (0x3<< SPI_MODE_OFFSET)
>>
>> #define SPI_TMOD_OFFSET 8
>> #define SPI_TMOD_MASK (0x3<< SPI_TMOD_OFFSET)
>> @@ -46,6 +48,7 @@
>> #define SPI_INT_RXOI (1<< 3)
>> #define SPI_INT_RXFI (1<< 4)
>> #define SPI_INT_MSTI (1<< 5)
>> +#define SPI_INT_ALL 0x3f
>>
>> /* TX RX interrupt level threshold, max can be 256 */
>> #define SPI_INT_THRESHOLD 32
>> @@ -83,65 +86,67 @@ struct dw_spi;
>> struct dw_spi_dma_ops {
>> int (*dma_init)(struct dw_spi *dws);
>> void (*dma_exit)(struct dw_spi *dws);
>> - int (*dma_transfer)(struct dw_spi *dws, int cs_change);
>> + int (*dma_transfer)(struct dw_spi *dws);
>> +};
>> +
>> +enum xfer_type {
>> + PIO_XFER,
>> + INT_XFER,
>> + DMA_XFER,
>> +};
>> +
>> +
>> +struct xfer_state {
>> + const u8 *tx_buf;
>> + dma_addr_t tx_dma;
>> + u8 *rx_buf;
>> + dma_addr_t rx_dma;
>> + struct spi_message *msg;
>> + u32 n_bytes;
>> + u32 len;
>> + u32 sent;
>> + u32 rcvd;
>> + u32 err;
>> + u32 type;
>> + u32 tx_threshold;
>> + u32 rx_threshold;
>> + u32 irq_status;
>> + struct completion complete;
>> };
>>
>> struct dw_spi {
>> struct spi_master *master;
>> - struct spi_device *cur_dev;
>> struct device *parent_dev;
>> enum dw_ssi_type type;
>>
>> void __iomem *regs;
>> unsigned long paddr;
>> u32 iolen;
>> - int irq;
>> + u32 irq;
>> u32 fifo_len; /* depth of the FIFO buffer */
>> u32 max_freq; /* max bus freq supported */
>>
>> u16 bus_num;
>> u16 num_cs; /* supported slave numbers */
>> -
>> +
>> /* Driver message queue */
>> struct workqueue_struct *workqueue;
>> struct work_struct pump_messages;
>> spinlock_t lock;
>> struct list_head queue;
>> - int busy;
>> - int run;
>> -
>> - /* Message Transfer pump */
>> - struct tasklet_struct pump_transfers;
>> + u32 run;
>>
>> /* Current message transfer state info */
>> - struct spi_message *cur_msg;
>> - struct spi_transfer *cur_transfer;
>> - struct chip_data *cur_chip;
>> - struct chip_data *prev_chip;
>> - size_t len;
>> - void *tx;
>> - void *tx_end;
>> - void *rx;
>> - void *rx_end;
>> - int dma_mapped;
>> - dma_addr_t rx_dma;
>> - dma_addr_t tx_dma;
>> - size_t rx_map_len;
>> - size_t tx_map_len;
>> - u8 n_bytes; /* current is a 1/2 bytes op */
>> - u8 max_bits_per_word; /* maxim is 16b */
>> - u32 dma_width;
>> - int cs_change;
>> - irqreturn_t (*transfer_handler)(struct dw_spi *dws);
>> - void (*cs_control)(u32 command);
>> + struct xfer_state xfer;
>>
>> /* Dma info */
>> - int dma_inited;
>> +// int dma_width;
>> + u32 dma_inited;
>> struct dma_chan *txchan;
>> struct scatterlist tx_sgl;
>> struct dma_chan *rxchan;
>> struct scatterlist rx_sgl;
>> - int dma_chan_done;
>> + u32 dma_chan_done;
>> struct device *dma_dev;
>> dma_addr_t dma_addr; /* phy address of the Data register */
>> struct dw_spi_dma_ops *dma_ops;
>> @@ -163,30 +168,36 @@ struct dw_spi {
>> __raw_readw(&(((struct dw_spi_reg *)dw->regs)->name))
>> #define dw_writew(dw, name, val) \
>> __raw_writew((val),&(((struct dw_spi_reg *)dw->regs)->name))
>> +#define dw_readb(dw, name) \
>> + __raw_readb(&(((struct dw_spi_reg *)dw->regs)->name))
>> +#define dw_writeb(dw, name, val) \
>> + __raw_writeb((val),&(((struct dw_spi_reg *)dw->regs)->name))
>>
>> -static inline void spi_enable_chip(struct dw_spi *dws, int enable)
>> +static inline void dw_spi_disable(struct dw_spi *dws)
>> {
>> - dw_writel(dws, ssienr, (enable ? 1 : 0));
>> + dw_writel(dws, ssienr, 0);
>> }
>>
>> -static inline void spi_set_clk(struct dw_spi *dws, u16 div)
>> +static inline void dw_spi_enable(struct dw_spi *dws)
>> +{
>> + dw_writel(dws, ssienr, 1);
>> +}
>> +
>> +static inline void dw_spi_set_clk(struct dw_spi *dws, u16 div)
>> {
>> dw_writel(dws, baudr, div);
>> }
>>
>> -static inline void spi_chip_sel(struct dw_spi *dws, u16 cs)
>> +static inline void dw_spi_chip_sel(struct dw_spi *dws, u16 cs)
>> {
>> if (cs> dws->num_cs)
>> return;
>>
>> - if (dws->cs_control)
>> - dws->cs_control(1);
>> -
>> dw_writel(dws, ser, 1<< cs);
>> }
>>
>> /* Disable IRQ bits */
>> -static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
>> +static inline void dw_spi_mask_intr(struct dw_spi *dws, u32 mask)
>> {
>> u32 new_mask;
>>
>> @@ -195,7 +206,7 @@ static inline void spi_mask_intr(struct dw_spi *dws, u32 mask)
>> }
>>
>> /* Enable IRQ bits */
>> -static inline void spi_umask_intr(struct dw_spi *dws, u32 mask)
>> +static inline void dw_spi_umask_intr(struct dw_spi *dws, u32 mask)
>> {
>> u32 new_mask;
>>
>> @@ -208,6 +219,7 @@ extern void dw_spi_remove_host(struct dw_spi *dws);
>> extern int dw_spi_suspend_host(struct dw_spi *dws);
>> extern int dw_spi_resume_host(struct dw_spi *dws);
>> extern void dw_spi_xfer_done(struct dw_spi *dws);
>> +extern int dw_spi_stop_queue(struct dw_spi *dws);
>>
>> /* platform related setup */
>> extern int dw_spi_mid_init(struct dw_spi *dws); /* Intel MID platforms */
>> --
>> 1.7.3.4
>>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists