calling  saa7134_init+0x0/0x4a @ 1
saa7130/34: v4l2 driver version 0.2.16 loaded
ACPI: PCI Interrupt Link [LNED] enabled at IRQ 16
saa7134 0000:05:00.0: PCI INT A -> Link[LNED] -> GSI 16 (level, low) -> IRQ 16
saa7134[0]: found at 0000:05:00.0, rev: 1, irq: 16, latency: 64, mmio: 0xfdfffc00
saa7134[0]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected]
saa7134[0]: board init: gpio is cc06000
saa7134[0]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: 0c 22 17 44 03 11 e1 a1 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: 00 30 8d 18 3b 02 ff ff 74 50 ff ff ff ff ff ff
saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 2-0043: chip found @ 0x86 (saa7134[0])
tda9887 2-0043: creating new instance
tda9887 2-0043: tda988[5/6/7] found
tuner 2-0043: type set to tda9887
tuner 2-0043: tv freq set to 0.00
tuner 2-0043: TV freq (0.00) out of range (44-958)
tuner 2-0043: saa7134[0] tuner I2C addr 0x86 with type 74 used for 0x0e
Chip ID is not zero. It is not a TEA5767
tuner 2-0060: Setting mode_mask to 0x0e
tuner 2-0060: chip found @ 0xc0 (saa7134[0])
tuner 2-0060: tuner 0x60: Tuner type absent
tuner 2-0043: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
tuner 2-0043: set addr discarded for type 74, mask e. Asked to change tuner at addr 0xff, with mask e
tuner 2-0060: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
tuner 2-0060: defining GPIO callback
mt20xx 2-0060: microtune: companycode=3cbf part=42 rev=1c
mt20xx 2-0060: microtune MT2050 found, OK
tuner 2-0060: type set to MT2050
tuner 2-0060: tv freq set to 400.00
tuner 2-0060: saa7134[0] tuner I2C addr 0xc0 with type 33 used for 0x0e
tuner 2-0043: switching to v4l2
tuner 2-0060: switching to v4l2
tuner 2-0060: tv freq set to 400.00
tuner 2-0060: tv freq set to 400.00
tuner 2-0043: Putting tuner to sleep
tuner 2-0043: Cmd s_power accepted for analog TV
tuner 2-0060: Putting tuner to sleep
tuner 2-0060: Cmd s_power accepted for analog TV
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
saa7134 0000:05:02.0: PCI INT A -> Link[LNEB] -> GSI 18 (level, low) -> IRQ 18
saa7134[1]: found at 0000:05:02.0, rev: 1, irq: 18, latency: 64, mmio: 0xfdfff800
saa7134[1]: subsystem: 11bd:002d, board: Pinnacle PCTV 300i DVB-T + PAL [card=50,autodetected]
saa7134[1]: board init: gpio is c806000
saa7134[1]: i2c eeprom 00: bd 11 2d 00 f8 f8 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[1]: i2c eeprom 10: 00 f0 04 04 ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 20: 01 40 01 02 03 ff 03 01 08 ff 00 25 ff ff ff ff
saa7134[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 40: ff 16 00 c0 86 3c 01 01 ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 60: 0c 22 17 44 03 27 32 08 ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 70: 00 30 8d 18 c8 4b ff ff 34 60 ff ff ff ff ff ff
saa7134[1]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[1]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 3-0043: chip found @ 0x86 (saa7134[1])
tda9887 3-0043: creating new instance
tda9887 3-0043: tda988[5/6/7] found
tuner 3-0043: type set to tda9887
tuner 3-0043: tv freq set to 0.00
tuner 3-0043: TV freq (0.00) out of range (44-958)
tuner 3-0043: saa7134[1] tuner I2C addr 0x86 with type 74 used for 0x0e
Chip ID is not zero. It is not a TEA5767
tuner 3-0060: Setting mode_mask to 0x0e
tuner 3-0060: chip found @ 0xc0 (saa7134[1])
tuner 3-0060: tuner 0x60: Tuner type absent
tuner 3-0043: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
tuner 3-0043: set addr discarded for type 74, mask e. Asked to change tuner at addr 0xff, with mask e
tuner 3-0060: Calling set_type_addr for type=33, addr=0xff, mode=0x0e, config=0x00
tuner 3-0060: defining GPIO callback
mt20xx 3-0060: microtune: companycode=3cbf part=42 rev=22
mt20xx 3-0060: microtune MT2050 found, OK
tuner 3-0060: type set to MT2050
tuner 3-0060: tv freq set to 400.00
tuner 3-0060: saa7134[1] tuner I2C addr 0xc0 with type 33 used for 0x0e
tuner 3-0043: switching to v4l2
tuner 3-0060: switching to v4l2
tuner 3-0060: tv freq set to 400.00
tuner 3-0060: tv freq set to 400.00
tuner 3-0043: Putting tuner to sleep
tuner 3-0043: Cmd s_power accepted for analog TV
tuner 3-0060: Putting tuner to sleep
tuner 3-0060: Cmd s_power accepted for analog TV
saa7134[1]: registered device video1 [v4l2]
saa7134[1]: registered device vbi1
initcall saa7134_init+0x0/0x4a returned 0 after 372541 usecs