Consolidate the io-apic EOI code in clear_IO_APIC_pin() and eoi_ioapic_irq(). Signed-off-by: Suresh Siddha Cc: Thomas Renninger Cc: Rafael Wysocki Cc: Maciej W. Rozycki --- arch/x86/kernel/apic/io_apic.c | 139 +++++++++++++++++++---------------------- 1 file changed, 65 insertions(+), 74 deletions(-) Index: linux-2.6-tip/arch/x86/kernel/apic/io_apic.c =================================================================== --- linux-2.6-tip.orig/arch/x86/kernel/apic/io_apic.c +++ linux-2.6-tip/arch/x86/kernel/apic/io_apic.c @@ -581,6 +581,66 @@ static void unmask_ioapic_irq(struct irq unmask_ioapic(data->chip_data); } +/* + * IO-APIC versions below 0x20 don't support EOI register. + * For the record, here is the information about various versions: + * 0Xh 82489DX + * 1Xh I/OAPIC or I/O(x)APIC which are not PCI 2.2 Compliant + * 2Xh I/O(x)APIC which is PCI 2.2 Compliant + * 30h-FFh Reserved + * + * Some of the Intel ICH Specs (ICH2 to ICH5) documents the io-apic + * version as 0x2. This is an error with documentation and these ICH chips + * use io-apic's of version 0x20. + * + * For IO-APIC's with EOI register, we use that to do an explicit EOI. + * Otherwise, we simulate the EOI message manually by changing the trigger + * mode to edge and then back to level, with RTE being masked during this. + */ +static void __eoi_ioapic_pin(int apic, int pin, int vector, struct irq_cfg *cfg) +{ + if (mpc_ioapic_ver(apic) >= 0x20) { + /* + * Intr-remapping uses pin number as the virtual vector + * in the RTE. Actual vector is programmed in + * intr-remapping table entry. Hence for the io-apic + * EOI we use the pin number. + */ + if (cfg && irq_remapped(cfg)) + io_apic_eoi(apic, pin); + else + io_apic_eoi(apic, vector); + } else { + struct IO_APIC_route_entry entry, entry1; + + entry = entry1 = __ioapic_read_entry(apic, pin); + + /* + * Mask the entry and change the trigger mode to edge. + */ + entry1.mask = 1; + entry1.trigger = IOAPIC_EDGE; + + __ioapic_write_entry(apic, pin, entry1); + + /* + * Restore the previous level triggered entry. + */ + __ioapic_write_entry(apic, pin, entry); + } +} + +static void eoi_ioapic_irq(unsigned int irq, struct irq_cfg *cfg) +{ + struct irq_pin_list *entry; + unsigned long flags; + + raw_spin_lock_irqsave(&ioapic_lock, flags); + for_each_irq_pin(entry, cfg->irq_2_pin) + __eoi_ioapic_pin(entry->apic, entry->pin, cfg->vector, cfg); + raw_spin_unlock_irqrestore(&ioapic_lock, flags); +} + static void clear_IO_APIC_pin(unsigned int apic, unsigned int pin) { struct IO_APIC_route_entry entry; @@ -601,6 +661,8 @@ static void clear_IO_APIC_pin(unsigned i } if (entry.irr) { + unsigned long flags; + /* * Make sure the trigger mode is set to level. Explicit EOI * doesn't clear the remoteIRR if the trigger mode is not @@ -611,23 +673,9 @@ static void clear_IO_APIC_pin(unsigned i ioapic_write_entry(apic, pin, entry); } - if (mpc_ioapic_ver(apic) >= 0x20) { - unsigned long flags; - - raw_spin_lock_irqsave(&ioapic_lock, flags); - io_apic_eoi(apic, entry.vector); - raw_spin_unlock_irqrestore(&ioapic_lock, flags); - } else { - /* - * Mechanism by which we clear remoteIRR in this - * case is by changing the trigger mode to edge and - * back to level. - */ - entry.trigger = IOAPIC_EDGE; - ioapic_write_entry(apic, pin, entry); - entry.trigger = IOAPIC_LEVEL; - ioapic_write_entry(apic, pin, entry); - } + raw_spin_lock_irqsave(&ioapic_lock, flags); + __eoi_ioapic_pin(apic, pin, entry.vector, NULL); + raw_spin_unlock_irqrestore(&ioapic_lock, flags); } /* @@ -2449,63 +2497,6 @@ static void ack_apic_edge(struct irq_dat atomic_t irq_mis_count; -/* - * IO-APIC versions below 0x20 don't support EOI register. - * For the record, here is the information about various versions: - * 0Xh 82489DX - * 1Xh I/OAPIC or I/O(x)APIC which are not PCI 2.2 Compliant - * 2Xh I/O(x)APIC which is PCI 2.2 Compliant - * 30h-FFh Reserved - * - * Some of the Intel ICH Specs (ICH2 to ICH5) documents the io-apic - * version as 0x2. This is an error with documentation and these ICH chips - * use io-apic's of version 0x20. - * - * For IO-APIC's with EOI register, we use that to do an explicit EOI. - * Otherwise, we simulate the EOI message manually by changing the trigger - * mode to edge and then back to level, with RTE being masked during this. -*/ -static void eoi_ioapic_irq(unsigned int irq, struct irq_cfg *cfg) -{ - struct irq_pin_list *entry; - unsigned long flags; - - raw_spin_lock_irqsave(&ioapic_lock, flags); - for_each_irq_pin(entry, cfg->irq_2_pin) { - if (mpc_ioapic_ver(entry->apic) >= 0x20) { - /* - * Intr-remapping uses pin number as the virtual vector - * in the RTE. Actual vector is programmed in - * intr-remapping table entry. Hence for the io-apic - * EOI we use the pin number. - */ - if (irq_remapped(cfg)) - io_apic_eoi(entry->apic, entry->pin); - else - io_apic_eoi(entry->apic, cfg->vector); - } else { - struct IO_APIC_route_entry rte, rte1; - - rte = rte1 = - __ioapic_read_entry(entry->apic, entry->pin); - - /* - * Mask the entry and change the trigger mode to edge. - */ - rte1.mask = 1; - rte1.trigger = IOAPIC_EDGE; - - __ioapic_write_entry(apic, pin, rte1); - - /* - * Restore the previous level triggered entry. - */ - __ioapic_write_entry(apic, pin, rte); - } - } - raw_spin_unlock_irqrestore(&ioapic_lock, flags); -} - static void ack_apic_level(struct irq_data *data) { struct irq_cfg *cfg = data->chip_data; -- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/