From 74d81235f8e4bd60859d539a27e51d3a09d183cf Mon Sep 17 00:00:00 2001 From: Jon Mason Date: Thu, 8 Sep 2011 12:59:00 -0500 Subject: [PATCH 2/2] PCI: Remove MRRS modification from MPS setting code Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has massive negative ramifications on some devices. Without knowing which devices have this issue, do not modify from the default value when walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe the default procedure. Tested-by: Sven Schnelle Tested-by: Simon Kirby Tested-by: Stephen M. Cameron Reported-and-tested-by: Eric Dumazet Reported-and-tested-by: Niels Ole Salscheider References: https://bugzilla.kernel.org/show_bug.cgi?id=42162 Signed-off-by: Jon Mason --- drivers/pci/pci.c | 2 +- drivers/pci/probe.c | 41 ++++++++++++++++++++++------------------- 2 files changed, 23 insertions(+), 20 deletions(-) diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c index 0ce6742..4e84fd4 100644 --- a/drivers/pci/pci.c +++ b/drivers/pci/pci.c @@ -77,7 +77,7 @@ unsigned long pci_cardbus_mem_size = DEFAULT_CARDBUS_MEM_SIZE; unsigned long pci_hotplug_io_size = DEFAULT_HOTPLUG_IO_SIZE; unsigned long pci_hotplug_mem_size = DEFAULT_HOTPLUG_MEM_SIZE; -enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_PERFORMANCE; +enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_SAFE; /* * The default CLS is used if arch didn't set CLS explicitly and not diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 0820fc1..b1187ff 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -1396,34 +1396,37 @@ static void pcie_write_mps(struct pci_dev *dev, int mps) static void pcie_write_mrrs(struct pci_dev *dev, int mps) { - int rc, mrrs; + int rc, mrrs, dev_mpss; - if (pcie_bus_config == PCIE_BUS_PERFORMANCE) { - int dev_mpss = 128 << dev->pcie_mpss; + /* In the "safe" case, do not configure the MRRS. There appear to be + * issues with setting MRRS to 0 on a number of devices. + */ - /* For Max performance, the MRRS must be set to the largest - * supported value. However, it cannot be configured larger - * than the MPS the device or the bus can support. This assumes - * that the largest MRRS available on the device cannot be - * smaller than the device MPSS. - */ - mrrs = mps < dev_mpss ? mps : dev_mpss; - } else - /* In the "safe" case, configure the MRRS for fairness on the - * bus by making all devices have the same size - */ - mrrs = mps; + if (pcie_bus_config != PCIE_BUS_PERFORMANCE) + return; + + dev_mpss = 128 << dev->pcie_mpss; + /* For Max performance, the MRRS must be set to the largest supported + * value. However, it cannot be configured larger than the MPS the + * device or the bus can support. This assumes that the largest MRRS + * available on the device cannot be smaller than the device MPSS. + */ + mrrs = min(mps, dev_mpss); /* MRRS is a R/W register. Invalid values can be written, but a - * subsiquent read will verify if the value is acceptable or not. + * subsequent read will verify if the value is acceptable or not. * If the MRRS value provided is not acceptable (e.g., too large), * shrink the value until it is acceptable to the HW. */ while (mrrs != pcie_get_readrq(dev) && mrrs >= 128) { + dev_warn(&dev->dev, "Attempting to modify the PCI-E MRRS value" + " to %d. If any issues are encountered, please try " + "running with pci=pcie_bus_safe\n", mrrs); rc = pcie_set_readrq(dev, mrrs); if (rc) - dev_err(&dev->dev, "Failed attempting to set the MRRS\n"); + dev_err(&dev->dev, + "Failed attempting to set the MRRS\n"); mrrs /= 2; } @@ -1436,13 +1439,13 @@ static int pcie_bus_configure_set(struct pci_dev *dev, void *data) if (!pci_is_pcie(dev)) return 0; - dev_info(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", + dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", pcie_get_mps(dev), 128<pcie_mpss, pcie_get_readrq(dev)); pcie_write_mps(dev, mps); pcie_write_mrrs(dev, mps); - dev_info(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", + dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", pcie_get_mps(dev), 128<pcie_mpss, pcie_get_readrq(dev)); return 0; -- 1.7.6