[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-ID: <1316434932.344.119.camel@L-0761.kpit.com>
Date: Mon, 19 Sep 2011 17:52:12 +0530
From: ashishj3 <ashish.jangam@...tcummins.com>
To: <dmitry.torokhov@...il.com>
CC: <m.grzeschik@...gutronix.de>, <randy.dunlap@...cle.com>,
<linaro-dev@...ts.linaro.org>, <linux-kernel@...r.kernel.org>,
Mark Brown <broonie@...nsource.wolfsonmicro.com>,
Dajun <dajun.chen@...semi.com>
Subject: [Patch v3 08/11] Touch: DA9052 touchscreen driver
This driver add support for DA9052 4-wire resistive ADC interfaced touchscreen
controller.
DA9052 is a MFD therefore this driver depends on DA9052 core driver for core
functionalities.
Signed-off-by: David Dajun Chen <dchen@...semi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@...tcummins.com>
---
Changes since v3:
- Remove unrequire type cast
- Prefix init code with _devinit
- Remove check for workqueue reschedule
- tsi_close() to wait for datardy intr completion
- Remove seperate workqueue
- Move cancel_work_sync to tsi_close()
- Check for drv data before tsi priv data allocation
Changes since v2:
- Replace kthreads with workqueue
- Remove kfifos
- Taken care for bus type
- Replace da9052_set/clear function with da9052_reg_update
- Add open and close functionality
---
drivers/input/touchscreen/Kconfig | 7 +
drivers/input/touchscreen/Makefile | 1 +
drivers/input/touchscreen/da9052_tsi.c | 369 ++++++++++++++++++++++++++++++++
3 files changed, 377 insertions(+), 0 deletions(-)
create mode 100755 drivers/input/touchscreen/da9052_tsi.c
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index cabd9e5..a5d2e7b 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -144,6 +144,13 @@ config TOUCHSCREEN_DA9034
Say Y here to enable the support for the touchscreen found
on Dialog Semiconductor DA9034 PMIC.
+config TOUCHSCREEN_DA9052
+ tristate "Dialog DA9052 TSI"
+ depends on PMIC_DA9052
+ help
+ Say y here to support the touchscreen found on
+ Dialog Semiconductor DA9052 PMIC
+
config TOUCHSCREEN_DYNAPRO
tristate "Dynapro serial touchscreen"
select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 282d6f7..a4aeb25 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
obj-$(CONFIG_TOUCHSCREEN_DA9034) += da9034-ts.o
+obj-$(CONFIG_TOUCHSCREEN_DA9052) += da9052_tsi.o
obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
obj-$(CONFIG_TOUCHSCREEN_HAMPSHIRE) += hampshire.o
obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
diff --git a/drivers/input/touchscreen/da9052_tsi.c b/drivers/input/touchscreen/da9052_tsi.c
new file mode 100755
index 0000000..0897340
--- /dev/null
+++ b/drivers/input/touchscreen/da9052_tsi.c
@@ -0,0 +1,369 @@
+/*
+ * TSI driver for Dialog DA9052
+ *
+ * Copyright(c) 2011 Dialog Semiconductor Ltd.
+ *
+ * Author: David Dajun Chen <dchen@...semi.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+#include <linux/module.h>
+#include <linux/input.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/da9052/reg.h>
+#include <linux/mfd/da9052/da9052.h>
+
+#define TSI_PEN_DOWN_STATUS 0x40
+
+struct da9052_tsi_reg {
+ u16 x;
+ u16 y;
+ u16 z;
+};
+
+struct da9052_tsi {
+ struct da9052 *da9052;
+ struct input_dev *dev;
+ struct delayed_work ts_pen_work;
+ int irq_pendwn;
+ int irq_datardy;
+};
+
+static int da9052_ts_start(struct da9052_tsi *tsi)
+{
+ return da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG,
+ 1 << 0, 1 << 0);
+}
+
+static int da9052_ts_stop(struct da9052_tsi *tsi)
+{
+ return da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG, 1 << 0, 0);
+}
+
+static irqreturn_t da9052_ts_pendwn_irq(int irq, void *data)
+{
+ struct da9052_tsi *tsi = data;
+ struct da9052 *da9052 = tsi->da9052;
+ int ret;
+
+ /* Mask PEN_DOWN event and unmask TSI_READY event */
+ da9052->events_mask |= DA9052_E_PEN_DOWN;
+ da9052->events_mask &= ~DA9052_E_TSI_READY;
+ ret = da9052_reg_update(da9052, DA9052_IRQ_MASK_B_REG, 0x80, 0x40);
+ if (ret < 0)
+ return IRQ_NONE;
+
+ da9052_ts_start(tsi);
+
+ input_report_key(tsi->dev, BTN_TOUCH, 1);
+ input_sync(tsi->dev);
+
+ return IRQ_HANDLED;
+}
+
+static int da9052_ts_read(struct da9052_tsi *tsi)
+{
+ struct da9052_tsi_reg co_ord = {0, 0, 0};
+ int ret;
+ uint8_t _x, _y, _z, _v;
+
+ ret = da9052_reg_read(tsi->da9052, DA9052_TSI_X_MSB_REG);
+ if (ret < 0)
+ return ret;
+
+ _x = (uint8_t) ret;
+
+ ret = da9052_reg_read(tsi->da9052, DA9052_TSI_Y_MSB_REG);
+ if (ret < 0)
+ return ret;
+
+ _y = (uint8_t) ret;
+
+ ret = da9052_reg_read(tsi->da9052, DA9052_TSI_Z_MSB_REG);
+ if (ret < 0)
+ return ret;
+
+ _z = (uint8_t) ret;
+
+ ret = da9052_reg_read(tsi->da9052, DA9052_TSI_LSB_REG);
+ if (ret < 0)
+ return ret;
+
+ _v = (uint8_t) ret;
+
+ co_ord.x = ((_x << 2) & 0x3fc) | (_v & 0x3);
+ co_ord.y = ((_y << 2) & 0x3fc) | ((_v & 0xc) >> 2);
+ co_ord.z = ((_z << 2) & 0x3fc) | ((_v & 0x30) >> 4);
+
+ input_report_abs(tsi->dev, ABS_X, co_ord.x);
+ input_report_abs(tsi->dev, ABS_Y, co_ord.y);
+ input_report_abs(tsi->dev, ABS_PRESSURE, co_ord.z);
+ input_report_key(tsi->dev, BTN_TOUCH, 1);
+ input_sync(tsi->dev);
+
+ return 0;
+}
+
+static irqreturn_t da9052_ts_datardy_irq(int irq, void *data)
+{
+ struct da9052_tsi *tsi = data;
+
+ da9052_ts_read(tsi);
+ schedule_delayed_work(&tsi->ts_pen_work, HZ/50);
+ return IRQ_HANDLED;
+}
+
+static void da9052_ts_pen_work(struct work_struct *work)
+{
+ struct da9052_tsi *tsi = container_of(work, struct da9052_tsi,
+ ts_pen_work.work);
+ struct input_dev *ip_dev = tsi->dev;
+ struct da9052 *da9052 = tsi->da9052;
+ int ret;
+
+ ret = da9052_reg_read(tsi->da9052, DA9052_TSI_LSB_REG);
+ if (ret < 0)
+ return;
+
+ if (ret & TSI_PEN_DOWN_STATUS) /* Pen Down */
+ schedule_delayed_work(&tsi->ts_pen_work, HZ/50);
+ else {
+ /* Pen UP */
+ da9052_ts_stop(tsi);
+
+ /* Unmask PEN_DOWN event */
+ da9052->events_mask &= ~DA9052_E_PEN_DOWN;
+ da9052_reg_update(da9052, DA9052_IRQ_MASK_B_REG, 0x40, 0);
+
+ /* Report Pen UP */
+ input_report_abs(ip_dev, ABS_PRESSURE, 0);
+ input_report_key(ip_dev, BTN_TOUCH, 0);
+ input_sync(ip_dev);
+ }
+}
+
+static int __devinit da9052_ts_configure_gpio(struct da9052 *da9052)
+{
+ int ret;
+
+ ret = da9052_reg_update(da9052, DA9052_GPIO_2_3_REG, 0x30, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = da9052_reg_update(da9052, DA9052_GPIO_4_5_REG, 0x33, 0);
+ if (ret < 0)
+ return ret;
+
+ ret = da9052_reg_update(da9052, DA9052_GPIO_6_7_REG, 0x33, 0);
+
+ return ret;
+}
+
+static int __devinit da9052_configure_tsi(struct da9052_tsi *tsi)
+{
+ ssize_t ret;
+ struct da9052 *da9052 = tsi->da9052;
+
+ ret = da9052_ts_configure_gpio(tsi->da9052);
+ if (ret < 0)
+ return ret;
+
+ /* Measure TSI sample every 1ms */
+ ret = da9052_reg_update(tsi->da9052, DA9052_ADC_CONT_REG,
+ 1 << 6, 1 << 6);
+ if (ret < 0)
+ return ret;
+
+ /* TSI_DELAY: 3 slots, TSI_SKIP: 0 slots, TSI_MODE: XYZP */
+ ret = da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG, 0xFC, 0xC0);
+ if (ret < 0)
+ return ret;
+
+ /* Mask TSI_READY event */
+ da9052->events_mask |= DA9052_E_TSI_READY;
+ ret = da9052_reg_update(da9052, DA9052_IRQ_MASK_B_REG, 0, 0x80);
+ if (ret < 0)
+ return ret;
+
+ /*Supply TSIRef through LD09 */
+ ret = da9052_reg_write(tsi->da9052, DA9052_LDO9_REG, 0x59);
+
+ return ret;
+}
+
+static int da9052_ts_input_open(struct input_dev *input_dev)
+{
+ struct da9052_tsi *tsi = input_get_drvdata(input_dev);
+
+ /* Enable Pen Detect Circuit */
+ return da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG,
+ 1 << 1, 1 << 1);
+}
+
+static void da9052_ts_input_close(struct input_dev *input_dev)
+{
+ struct da9052_tsi *tsi = input_get_drvdata(input_dev);
+
+ cancel_delayed_work_sync(&tsi->ts_pen_work);
+
+ da9052_ts_stop(tsi);
+
+ /* Disable Pen Detect Circuit */
+ da9052_reg_update(tsi->da9052, DA9052_TSI_CONT_A_REG, 1 << 1, 0);
+}
+
+static int __devinit da9052_ts_probe(struct platform_device *pdev)
+{
+ struct da9052_tsi *tsi;
+ struct input_dev *input_dev;
+ struct da9052 *da9052;
+ int ret;
+
+ da9052 = dev_get_drvdata(pdev->dev.parent);
+ if (da9052 == NULL)
+ return -EINVAL;
+
+ tsi = kzalloc(sizeof(struct da9052_tsi), GFP_KERNEL);
+ if (!tsi)
+ return -ENOMEM;
+
+ input_dev = input_allocate_device();
+ if (!input_dev) {
+ dev_err(tsi->da9052->dev, "Failed to allocate input device\n");
+ ret = -ENOMEM;
+ goto err_mem;
+ }
+
+ INIT_DELAYED_WORK(&tsi->ts_pen_work, da9052_ts_pen_work);
+
+ tsi->da9052 = da9052;
+
+ input_dev->id.version = 0x0101;
+ input_dev->id.vendor = 0x15B6;
+ input_dev->id.product = 0x9052;
+ input_dev->id.bustype = tsi->da9052->bustype;
+ input_dev->name = "Dialog DA9052 TouchScreen Driver";
+ input_dev->dev.parent = &pdev->dev;
+ input_dev->open = da9052_ts_input_open;
+ input_dev->close = da9052_ts_input_close;
+ __set_bit(EV_ABS, input_dev->evbit);
+ __set_bit(EV_KEY, input_dev->evbit);
+ __set_bit(BTN_TOUCH, input_dev->keybit);
+ __set_bit(ABS_X, input_dev->absbit);
+ __set_bit(ABS_Y, input_dev->absbit);
+ __set_bit(ABS_PRESSURE, input_dev->absbit);
+
+ input_set_abs_params(input_dev, ABS_X, 0, 1023, 0, 0);
+ input_set_abs_params(input_dev, ABS_Y, 0, 1023, 0, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE, 0, 1023, 0, 0);
+
+ tsi->dev = input_dev;
+ input_set_drvdata(input_dev, tsi);
+
+ tsi->irq_pendwn = platform_get_irq_byname(pdev, "PENDWN");
+ if (tsi->irq_pendwn < 0) {
+ ret = tsi->irq_pendwn;
+ goto err_input;
+ }
+
+ ret = request_threaded_irq(tsi->da9052->irq_base + tsi->irq_pendwn,
+ NULL, da9052_ts_pendwn_irq,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "PENDWN", tsi);
+ if (ret < 0) {
+ dev_err(tsi->da9052->dev,
+ "Failed to register %s IRQ %d, error = %d\n", "PENDWN",
+ tsi->da9052->irq_base + tsi->irq_pendwn, ret);
+ goto err_input;
+ }
+
+ tsi->irq_datardy = platform_get_irq_byname(pdev, "TSIRDY");
+ if (tsi->irq_datardy < 0) {
+ ret = tsi->irq_datardy;
+ goto err_pendwn_irq;
+ }
+
+ ret = request_threaded_irq(tsi->da9052->irq_base + tsi->irq_datardy,
+ NULL, da9052_ts_datardy_irq,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "TSIRDY", tsi);
+ if (ret < 0) {
+ dev_err(tsi->da9052->dev,
+ "Failed to register %s IRQ %d, error = %d\n", "TSIRDY",
+ tsi->da9052->irq_base + tsi->irq_datardy, ret);
+ goto err_pendwn_irq;
+ }
+
+ ret = da9052_configure_tsi(tsi);
+ if (ret < 0)
+ goto err_datardy_irq;
+
+ ret = input_register_device(tsi->dev);
+ if (ret < 0)
+ goto err_datardy_irq;
+
+ platform_set_drvdata(pdev, tsi);
+
+ return 0;
+
+err_datardy_irq:
+ free_irq(tsi->da9052->irq_base + tsi->irq_datardy, tsi);
+err_pendwn_irq:
+ free_irq(tsi->da9052->irq_base + tsi->irq_pendwn, tsi);
+err_input:
+ input_free_device(input_dev);
+err_mem:
+ kfree(tsi);
+ return ret;
+}
+
+static int __devexit da9052_ts_remove(struct platform_device *pdev)
+{
+ struct da9052_tsi *tsi = platform_get_drvdata(pdev);
+
+ da9052_reg_write(tsi->da9052, DA9052_LDO9_REG, 0x19);
+
+ free_irq(tsi->da9052->irq_base + tsi->irq_pendwn, tsi);
+ free_irq(tsi->da9052->irq_base + tsi->irq_datardy, tsi);
+
+ input_unregister_device(tsi->dev);
+
+ platform_set_drvdata(pdev, NULL);
+
+ kfree(tsi);
+
+ return 0;
+}
+
+static struct platform_driver da9052_tsi_driver = {
+
+ .probe = da9052_ts_probe,
+ .remove = __devexit_p(da9052_ts_remove),
+ .driver = {
+ .name = "da9052-tsi",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init da9052_ts_init(void)
+{
+ return platform_driver_register(&da9052_tsi_driver);
+}
+module_init(da9052_ts_init);
+
+static void __exit da9052_ts_exit(void)
+{
+ platform_driver_unregister(&da9052_tsi_driver);
+}
+module_exit(da9052_ts_exit);
+
+MODULE_DESCRIPTION("Touchscreen driver for Dialog Semiconductor DA9052");
+MODULE_AUTHOR("David Dajun Chen <dchen@...semi.com>");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:da9052-tsi");
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists