| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1316974677-17108-3-git-send-email-mark.einon@gmail.com>
Date: Sun, 25 Sep 2011 19:17:54 +0100
From: Mark Einon <mark.einon@...il.com>
To: gregkh@...e.de
Cc: devel@...verdev.osuosl.org, linux-kernel@...r.kernel.org,
o.hartmann@...ovital.com, alan@...ux.intel.com,
Mark Einon <mark.einon@...il.com>
Subject: [PATCH 3/6] staging: et131x: Remove et131x_check_mii() and move functionality into et131x_adjust_link()
et131x_check_mii() is now only being called from et131x_adjust_link.
Removed this call and associated subroutines, putting the functionality directly into et131x_adjust_link(), in preparation for further simplification.
Changed register checks from bare BMSR checks to use phydev/netif versions, also now uses adapter->link to track link state changes.
Signed-off-by: Mark Einon <mark.einon@...il.com>
---
drivers/staging/et131x/et1310_phy.c | 167 -------------------------------
drivers/staging/et131x/et131x_initpci.c | 115 ++++++++++++++++++---
2 files changed, 98 insertions(+), 184 deletions(-)
diff --git a/drivers/staging/et131x/et1310_phy.c b/drivers/staging/et131x/et1310_phy.c
index c4bc41d..fc37b18 100644
--- a/drivers/staging/et131x/et1310_phy.c
+++ b/drivers/staging/et131x/et1310_phy.c
@@ -298,68 +298,6 @@ void et1310_phy_power_down(struct et131x_adapter *adapter, bool down)
et131x_mii_write(adapter, MII_BMCR, data);
}
-/**
- * et1310_phy_link_status - read link state
- * @adapter: device to read
- * @link_status: reported link state
- * @autoneg: reported autonegotiation state (complete/incomplete/disabled)
- * @linkspeed: returnedlink speed in use
- * @duplex_mode: reported half/full duplex state
- * @mdi_mdix: not yet working
- * @masterslave: report whether we are master or slave
- * @polarity: link polarity
- *
- * I can read your lan like a magazine
- * I see if your up
- * I know your link speed
- * I see all the setting that you'd rather keep
- */
-static void et1310_phy_link_status(struct et131x_adapter *adapter,
- u8 *link_status,
- u32 *autoneg,
- u32 *linkspeed,
- u32 *duplex_mode,
- u32 *mdi_mdix,
- u32 *masterslave, u32 *polarity)
-{
- u16 mistatus = 0;
- u16 is1000BaseT = 0;
- u16 vmi_phystatus = 0;
- u16 control = 0;
-
- et131x_mii_read(adapter, MII_BMSR, &mistatus);
- et131x_mii_read(adapter, MII_STAT1000, &is1000BaseT);
- et131x_mii_read(adapter, PHY_PHY_STATUS, &vmi_phystatus);
- et131x_mii_read(adapter, MII_BMCR, &control);
-
- *link_status = (vmi_phystatus & ET_PHY_LSTATUS) ? 1 : 0;
- *autoneg = (control & ET_PHY_AUTONEG_STATUS) ?
- ((vmi_phystatus & ET_PHY_AUTONEG_ENABLE) ?
- TRUEPHY_ANEG_COMPLETE :
- TRUEPHY_ANEG_NOT_COMPLETE) :
- TRUEPHY_ANEG_DISABLED;
- *linkspeed = (vmi_phystatus & ET_PHY_SPEED_STATUS) >> 8;
- *duplex_mode = (vmi_phystatus & ET_PHY_DUPLEX_STATUS) >> 7;
- /* NOTE: Need to complete this */
- *mdi_mdix = 0;
-
- *masterslave = (is1000BaseT & ET_1000BT_MSTR_SLV) ?
- TRUEPHY_CFG_MASTER : TRUEPHY_CFG_SLAVE;
- *polarity = (vmi_phystatus & ET_PHY_POLARITY_STATUS) ?
- TRUEPHY_POLARITY_INVERTED : TRUEPHY_POLARITY_NORMAL;
-}
-
-static void et1310_phy_and_or_reg(struct et131x_adapter *adapter,
- u16 regnum, u16 and_mask, u16 or_mask)
-{
- u16 reg;
-
- et131x_mii_read(adapter, regnum, ®);
- reg &= and_mask;
- reg |= or_mask;
- et131x_mii_write(adapter, regnum, reg);
-}
-
/* Still used from _mac for BIT_READ */
void et1310_phy_access_mii_bit(struct et131x_adapter *adapter, u16 action,
u16 regnum, u16 bitnum, u8 *value)
@@ -437,108 +375,3 @@ void et131x_xcvr_init(struct et131x_adapter *adapter)
}
}
-void et131x_mii_check(struct et131x_adapter *adapter,
- u16 bmsr, u16 bmsr_ints)
-{
- struct phy_device *phydev = adapter->phydev;
- u8 link_status;
- u32 autoneg_status;
- u32 speed;
- u32 duplex;
- u32 mdi_mdix;
- u32 masterslave;
- u32 polarity;
-
- if (bmsr_ints & BMSR_LSTATUS) {
- if (bmsr & BMSR_LSTATUS) {
- adapter->boot_coma = 20;
- } else {
- dev_warn(&adapter->pdev->dev,
- "Link down - cable problem ?\n");
-
- if (phydev && phydev->speed == SPEED_10) {
- /* NOTE - Is there a way to query this without
- * TruePHY?
- * && TRU_QueryCoreType(adapter->hTruePhy, 0) ==
- * EMI_TRUEPHY_A13O) {
- */
- u16 register18;
-
- et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
- ®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
- register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
- register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
- }
-
- /* Free the packets being actively sent & stopped */
- et131x_free_busy_send_packets(adapter);
-
- /* Re-initialize the send structures */
- et131x_init_send(adapter);
-
- /* Reset the RFD list and re-start RU */
- et131x_reset_recv(adapter);
-
- /*
- * Bring the device back to the state it was during
- * init prior to autonegotiation being complete. This
- * way, when we get the auto-neg complete interrupt,
- * we can complete init by calling config_mac_regs2.
- */
- et131x_soft_reset(adapter);
-
- /* Setup ET1310 as per the documentation */
- et131x_adapter_setup(adapter);
- }
- }
-
- if (bmsr_ints & BMSR_ANEGCOMPLETE) {
- if (bmsr & BMSR_ANEGCOMPLETE) {
- et1310_phy_link_status(adapter,
- &link_status, &autoneg_status,
- &speed, &duplex, &mdi_mdix,
- &masterslave, &polarity);
-
- adapter->boot_coma = 20;
-
- if (phydev && phydev->speed == SPEED_10) {
- /*
- * NOTE - Is there a way to query this without
- * TruePHY?
- * && TRU_QueryCoreType(adapter->hTruePhy, 0)==
- * EMI_TRUEPHY_A13O) {
- */
- u16 register18;
-
- et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
- ®ister18);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18 | 0x4);
- et131x_mii_write(adapter, PHY_INDEX_REG,
- register18 | 0x8402);
- et131x_mii_write(adapter, PHY_DATA_REG,
- register18 | 511);
- et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
- register18);
- }
-
- et1310_config_flow_control(adapter);
-
- if (phydev && phydev->speed == SPEED_1000 &&
- adapter->registry_jumbo_packet > 2048)
- et1310_phy_and_or_reg(adapter, PHY_CONFIG,
- ~ET_PHY_CONFIG_TX_FIFO_DEPTH,
- ET_PHY_CONFIG_FIFO_DEPTH_32);
-
- et131x_set_rx_dma_timer(adapter);
- et1310_config_mac_regs2(adapter);
- }
- }
-}
-
diff --git a/drivers/staging/et131x/et131x_initpci.c b/drivers/staging/et131x/et131x_initpci.c
index 799aad6..618f844 100644
--- a/drivers/staging/et131x/et131x_initpci.c
+++ b/drivers/staging/et131x/et131x_initpci.c
@@ -446,29 +446,110 @@ static void et131x_adjust_link(struct net_device *netdev)
struct address_map __iomem *iomem = adapter->regs;
u32 pm_csr;
- u16 bmsr_ints;
- u16 bmsr_data;
- /* If we are in coma mode, we need to disable it. */
- pm_csr = readl(&iomem->global.pm_csr);
- if (pm_csr & ET_PM_PHY_SW_COMA) {
- /*
- * Check to see if we are in coma mode and if
- * so, disable it because we will not be able
- * to read PHY values until we are out.
- */
- et1310_disable_phy_coma(adapter);
+ if (netif_carrier_ok(netdev)) {
+ adapter->boot_coma = 20;
+
+ if (phydev && phydev->speed == SPEED_10) {
+ /*
+ * NOTE - Is there a way to query this without
+ * TruePHY?
+ * && TRU_QueryCoreType(adapter->hTruePhy, 0)==
+ * EMI_TRUEPHY_A13O) {
+ */
+ u16 register18;
+
+ et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
+ ®ister18);
+ et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
+ register18 | 0x4);
+ et131x_mii_write(adapter, PHY_INDEX_REG,
+ register18 | 0x8402);
+ et131x_mii_write(adapter, PHY_DATA_REG,
+ register18 | 511);
+ et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
+ register18);
+ }
+
+ et1310_config_flow_control(adapter);
+
+ if (phydev && phydev->speed == SPEED_1000 &&
+ adapter->registry_jumbo_packet > 2048) {
+ u16 reg;
+
+ et131x_mii_read(adapter, PHY_CONFIG, ®);
+ reg &= ~ET_PHY_CONFIG_TX_FIFO_DEPTH;
+ reg |= ET_PHY_CONFIG_FIFO_DEPTH_32;
+ et131x_mii_write(adapter, PHY_CONFIG, reg);
+ }
+
+ et131x_set_rx_dma_timer(adapter);
+ et1310_config_mac_regs2(adapter);
}
- et131x_phy_mii_read(adapter, phydev->addr, MII_BMSR, &bmsr_data);
+ if (phydev->link != adapter->link) {
+ /* If we are in coma mode, we need to disable it. */
+ pm_csr = readl(&iomem->global.pm_csr);
+ if (pm_csr & ET_PM_PHY_SW_COMA) {
+ /*
+ * Check to see if we are in coma mode and if
+ * so, disable it because we will not be able
+ * to read PHY values until we are out.
+ */
+ et1310_disable_phy_coma(adapter);
+ }
+
+ if (phydev->link) {
+ adapter->boot_coma = 20;
+ } else {
+ dev_warn(&adapter->pdev->dev,
+ "Link down - cable problem ?\n");
+
+ if (phydev && phydev->speed == SPEED_10) {
+ /* NOTE - Is there a way to query this without
+ * TruePHY?
+ * && TRU_QueryCoreType(adapter->hTruePhy, 0) ==
+ * EMI_TRUEPHY_A13O)
+ */
+ u16 register18;
+
+ et131x_mii_read(adapter, PHY_MPHY_CONTROL_REG,
+ ®ister18);
+ et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
+ register18 | 0x4);
+ et131x_mii_write(adapter, PHY_INDEX_REG,
+ register18 | 0x8402);
+ et131x_mii_write(adapter, PHY_DATA_REG,
+ register18 | 511);
+ et131x_mii_write(adapter, PHY_MPHY_CONTROL_REG,
+ register18);
+ }
+
+ /* Free the packets being actively sent & stopped */
+ et131x_free_busy_send_packets(adapter);
+
+ /* Re-initialize the send structures */
+ et131x_init_send(adapter);
- bmsr_ints = adapter->bmsr ^ bmsr_data;
- adapter->bmsr = bmsr_data;
+ /* Reset the RFD list and re-start RU */
+ et131x_reset_recv(adapter);
- /* Do all the cable in / cable out stuff */
- et131x_mii_check(adapter, bmsr_data, bmsr_ints);
+ /*
+ * Bring the device back to the state it was during
+ * init prior to autonegotiation being complete. This
+ * way, when we get the auto-neg complete interrupt,
+ * we can complete init by calling config_mac_regs2.
+ */
+ et131x_soft_reset(adapter);
- phy_print_status(phydev);
+ /* Setup ET1310 as per the documentation */
+ et131x_adapter_setup(adapter);
+ }
+
+ adapter->link = phydev->link;
+
+ phy_print_status(phydev);
+ }
}
int et131x_mii_probe(struct net_device *netdev)
--
1.7.6
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists