[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.2.0-rc2konrad-testing-20111123+ (root@serveerstertje) (gcc version 4.4.5 (Debian 4.4.5-8) ) #2 SMP Wed Nov 23 20:42:27 CET 2011 [ 0.000000] Command line: root=/dev/xvda2 ro iommu=soft [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] Released 0 pages of unused memory [ 0.000000] Set 0 page(s) to 1-1 mapping [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] Xen: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] Xen: 00000000000a0000 - 0000000000100000 (reserved) [ 0.000000] Xen: 0000000000100000 - 0000000020000000 (usable) [ 0.000000] Xen: 0000000020000000 - 0000000020800000 (unusable) [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI not present or invalid. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable) [ 0.000000] No AGP bridge found [ 0.000000] last_pfn = 0x20000 max_arch_pfn = 0x400000000 [ 0.000000] initial memory mapped : 0 - 02b09000 [ 0.000000] Base memory trampoline at [ffff88000009e000] 9e000 size 8192 [ 0.000000] init_memory_mapping: 0000000000000000-0000000020000000 [ 0.000000] 0000000000 - 0020000000 page 4k [ 0.000000] kernel direct mapping tables up to 20000000 @ 2377000-2479000 [ 0.000000] xen: setting RW the range 245b000 - 2479000 [ 0.000000] RAMDISK: 02479000 - 02b09000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000020000000 [ 0.000000] Initmem setup node 0 0000000000000000-0000000020000000 [ 0.000000] NODE_DATA [000000001fffb000 - 000000001fffffff] [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal empty [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x000000a0 [ 0.000000] 0: 0x00000100 -> 0x00020000 [ 0.000000] On node 0 totalpages: 130960 [ 0.000000] DMA zone: 64 pages used for memmap [ 0.000000] DMA zone: 2 pages reserved [ 0.000000] DMA zone: 3918 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 1984 pages used for memmap [ 0.000000] DMA32 zone: 124992 pages, LIFO batch:31 [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] nr_irqs_gsi: 16 [ 0.000000] Allocating PCI resources starting at 20800000 (gap: 20800000:df800000) [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.3-rc1-pre (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff88001ffd6000 s75776 r8192 d22528 u106496 [ 0.000000] pcpu-alloc: s75776 r8192 d22528 u106496 alloc=26*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 128910 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: root=/dev/xvda2 ro iommu=soft [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] Placing 64MB software IO TLB between ffff88001ae00000 - ffff88001ee00000 [ 0.000000] software IO TLB at phys 0x1ae00000 - 0x1ee00000 [ 0.000000] Memory: 423892k/524288k available (8561k kernel code, 448k absent, 99948k reserved, 6442k data, 780k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] Xen: using vcpuop timer interface [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3200.164 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6400.32 BogoMIPS (lpj=3200164) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Initializing. [ 0.000999] SELinux: Starting in permissive mode [ 0.000999] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000999] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000999] Mount-cache hash table entries: 256 [ 0.000999] Initializing cgroup subsys cpuacct [ 0.000999] Initializing cgroup subsys freezer [ 0.000999] tseg: 0000000000 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 5 [ 0.000999] SMP alternatives: switching to UP code [ 0.002017] Freeing SMP alternatives: 28k freed [ 0.002092] cpu 0 spinlock event irq 17 [ 0.002105] Performance Events: [ 0.002109] no APIC, boot with the "lapic" boot parameter to force-enable it. [ 0.002114] no hardware sampling interrupt available. [ 0.002136] Broken PMU hardware detected, using software events only. [ 0.002221] MCE: In-kernel MCE decoding enabled. [ 0.002226] Brought up 1 CPUs [ 0.002435] Grant tables using version 2 layout. [ 0.002449] Grant table initialized [ 0.021460] RTC time: 165:165:165, date: 165/165/65 [ 0.021499] NET: Registered protocol family 16 [ 0.021912] Extended Config Space enabled on 0 nodes [ 0.022283] PCI: setting up Xen PCI frontend stub [ 0.022290] PCI: pci_cache_line_size set to 64 bytes [ 0.035194] bio: create slab at 0 [ 0.035281] ACPI: Interpreter disabled. [ 0.035323] xen/balloon: Initialising balloon driver. [ 0.051039] xen-balloon: Initialising balloon driver. [ 0.051106] vgaarb: loaded [ 0.051259] SCSI subsystem initialized [ 0.051342] libata version 3.00 loaded. [ 0.052157] usbcore: registered new interface driver usbfs [ 0.052203] usbcore: registered new interface driver hub [ 0.052252] usbcore: registered new device driver usb [ 0.052502] Advanced Linux Sound Architecture Driver Version 1.0.24. [ 0.052508] PCI: System does not support PCI [ 0.052512] PCI: System does not support PCI [ 0.052672] NetLabel: Initializing [ 0.052676] NetLabel: domain hash size = 128 [ 0.052679] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.052691] NetLabel: unlabeled traffic allowed by default [ 0.052697] Switching to clocksource xen [ 0.052755] pnp: PnP ACPI: disabled [ 0.054819] PCI: max bus depth: 0 pci_try_num: 1 [ 0.054843] NET: Registered protocol family 2 [ 0.054903] IP route cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.055083] TCP established hash table entries: 16384 (order: 6, 262144 bytes) [ 0.055191] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.055249] TCP: Hash tables configured (established 16384 bind 16384) [ 0.055254] TCP reno registered [ 0.055261] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.055270] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.055314] NET: Registered protocol family 1 [ 0.055385] RPC: Registered named UNIX socket transport module. [ 0.055389] RPC: Registered udp transport module. [ 0.055393] RPC: Registered tcp transport module. [ 0.055396] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.055401] PCI: CLS 0 bytes, default 64 [ 0.055448] Trying to unpack rootfs image as initramfs... [ 0.062183] Freeing initrd memory: 6720k freed [ 0.065820] DMA-API: preallocated 32768 debug entries [ 0.065829] DMA-API: debugging enabled by kernel config [ 0.065933] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.066299] microcode: CPU0: patch_level=0x010000bf [ 0.066336] microcode: Microcode Update Driver: v2.00 , Peter Oruba [ 0.066512] audit: initializing netlink socket (disabled) [ 0.066527] type=2000 audit(1322320799.409:1): initialized [ 0.079499] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.082135] VFS: Disk quotas dquot_6.5.2 [ 0.082201] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.156893] NTFS driver 2.1.30 [Flags: R/W]. [ 0.157037] fuse init (API version 7.17) [ 0.157492] Btrfs loaded [ 0.157508] msgmni has been set to 841 [ 0.157592] SELinux: Registering netfilter hooks [ 0.157919] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.157928] io scheduler noop registered [ 0.157933] io scheduler deadline registered [ 0.157980] io scheduler cfq registered (default) [ 0.158243] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.158335] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.222693] usbcore: registered new interface driver udlfb [ 0.222952] Event-channel device installed. [ 0.223423] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.223835] Non-volatile memory driver v1.3 [ 0.223841] Linux agpgart interface v0.103 [ 0.223973] [drm] Initialized drm 1.1.0 20060810 [ 0.223980] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.225537] brd: module loaded [ 0.226273] loop: module loaded [ 0.692654] tun: Universal TUN/TAP device driver, 1.6 [ 0.692664] tun: (C) 1999-2004 Max Krasnyansky [ 0.692754] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI [ 0.692760] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 0.692803] sky2: driver version 1.30 [ 0.692872] Initialising Xen virtual ethernet driver. [ 0.700051] pcifront pci-0: Installing PCI frontend [ 0.700414] pcifront pci-0: Creating PCI Frontend Bus 0000:04 [ 0.700818] pci 0000:04:00.0: [9710:9990] type 0 class 0x000c03 [ 0.701004] pci 0000:04:00.0: reg 10: [mem 0xf9af8000-0xf9af8fff] [ 0.701402] pci 0000:04:00.0: supports D1 D2 [ 0.701402] pci 0000:04:00.1: [9710:9990] type 0 class 0x000c03 [ 0.701402] pci 0000:04:00.1: reg 10: [mem 0xf9af9000-0xf9af9fff] [ 0.701402] pci 0000:04:00.1: supports D1 D2 [ 0.701402] pci 0000:04:00.2: [9710:9990] type 0 class 0x000c03 [ 0.701402] pci 0000:04:00.2: reg 10: [mem 0xf9afa000-0xf9afafff] [ 0.701402] pci 0000:04:00.2: supports D1 D2 [ 0.701402] pci 0000:04:00.3: [9710:9990] type 0 class 0x000c03 [ 0.701402] pci 0000:04:00.3: reg 10: [mem 0xf9afb000-0xf9afbfff] [ 0.701402] pci 0000:04:00.3: supports D1 D2 [ 0.701402] pci 0000:04:00.4: [9710:9990] type 0 class 0x000c03 [ 0.701402] pci 0000:04:00.4: reg 10: [mem 0xf9afc000-0xf9afcfff] [ 0.701402] pci 0000:04:00.4: supports D1 D2 [ 0.708320] pci 0000:04:00.5: [9710:9990] type 0 class 0x000c03 [ 0.708471] pci 0000:04:00.5: reg 10: [mem 0xf9afd000-0xf9afdfff] [ 0.709143] pci 0000:04:00.5: supports D1 D2 [ 0.709143] pci 0000:04:00.6: [9710:9990] type 0 class 0x000c03 [ 0.709143] pci 0000:04:00.6: reg 10: [mem 0xf9afe000-0xf9afefff] [ 0.709143] pci 0000:04:00.6: supports D1 D2 [ 0.709143] pci 0000:04:00.7: [9710:9990] type 0 class 0x000c03 [ 0.709143] pci 0000:04:00.7: reg 10: [mem 0xf9aff000-0xf9afffff] [ 0.709143] pci 0000:04:00.7: supports D1 D2 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.0/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.1/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.2/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.3/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.4/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.5/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.6/0 [ 0.709143] pcifront pci-0: claiming resource 0000:04:00.7/0 [ 0.860059] blkfront: xvda1: flush diskcache: enabled [ 1.153200] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.153209] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96 [ 1.153715] ehci_hcd 0000:04:00.1: enabling device (0000 -> 0002) [ 1.154020] ehci_hcd 0000:04:00.1: Xen PCI mapped GSI40 to IRQ28 [ 1.154055] ehci_hcd 0000:04:00.1: setting latency timer to 64 [ 1.154055] ehci_hcd 0000:04:00.1: EHCI Host Controller [ 1.154055] drivers/usb/core/inode.c: creating file 'devices' [ 1.154055] drivers/usb/core/inode.c: creating file '001' [ 1.154365] ehci_hcd 0000:04:00.1: new USB bus registered, assigned bus number 1 [ 1.154378] ehci_hcd 0000:04:00.1: reset hcs_params 0x1191 dbg=0 cc=1 pcc=1 ports=1 [ 1.154382] ehci_hcd 0000:04:00.1: reset portroute 0 [ 1.154387] ehci_hcd 0000:04:00.1: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park [ 1.154434] ehci_hcd 0000:04:00.1: park 0 [ 1.154436] ehci_hcd 0000:04:00.1: applying MosChip frame-index workaround [ 1.154709] ehci_hcd 0000:04:00.1: reset command 0010006 (park)=0 ithresh=1 period=512 Reset HALT [ 1.154752] ehci_hcd 0000:04:00.1: Enabling legacy PCI PM [ 1.154761] ehci_hcd 0000:04:00.1: ...powerup ports... [ 1.155243] blkfront: xvda2: flush diskcache: enabled [ 1.175229] ehci_hcd 0000:04:00.1: MWI active [ 1.175234] ehci_hcd 0000:04:00.1: supports USB remote wakeup [ 1.175254] ehci_hcd 0000:04:00.1: irq 28, io mem 0xf9af9000 [ 1.175268] ehci_hcd 0000:04:00.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT [ 1.175279] ehci_hcd 0000:04:00.1: init command 0010005 (park)=0 ithresh=1 period=512 RUN [ 1.181165] ehci_hcd 0000:04:00.1: USB 2.0 started, EHCI 1.00 [ 1.181254] usb usb1: default language 0x0409 [ 1.181261] usb usb1: udev 1, busnum 1, minor = 0 [ 1.181263] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.181269] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.181274] usb usb1: Product: EHCI Host Controller [ 1.181278] usb usb1: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ehci_hcd [ 1.181284] usb usb1: SerialNumber: 0000:04:00.1 [ 1.181393] usb usb1: usb_probe_device [ 1.181396] usb usb1: configuration #1 chosen from 1 choice [ 1.181417] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 1.181462] hub 1-0:1.0: usb_probe_interface [ 1.181464] hub 1-0:1.0: usb_probe_interface - got id [ 1.181466] hub 1-0:1.0: USB hub found [ 1.181476] hub 1-0:1.0: 1 port detected [ 1.181479] hub 1-0:1.0: standalone hub [ 1.181481] hub 1-0:1.0: individual port power switching [ 1.181483] hub 1-0:1.0: individual port over-current protection [ 1.181485] hub 1-0:1.0: power on to power good time: 20ms [ 1.181488] hub 1-0:1.0: local power source is good [ 1.181491] hub 1-0:1.0: enabling power on all ports [ 1.181519] drivers/usb/core/inode.c: creating file '001' [ 1.181701] ehci_hcd 0000:04:00.3: enabling device (0000 -> 0002) [ 1.182027] ehci_hcd 0000:04:00.3: Xen PCI mapped GSI41 to IRQ29 [ 1.182104] ehci_hcd 0000:04:00.3: setting latency timer to 64 [ 1.182104] ehci_hcd 0000:04:00.3: EHCI Host Controller [ 1.182104] drivers/usb/core/inode.c: creating file '002' [ 1.182349] ehci_hcd 0000:04:00.3: new USB bus registered, assigned bus number 2 [ 1.182362] ehci_hcd 0000:04:00.3: reset hcs_params 0x1191 dbg=0 cc=1 pcc=1 ports=1 [ 1.182366] ehci_hcd 0000:04:00.3: reset portroute 0 [ 1.182371] ehci_hcd 0000:04:00.3: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park [ 1.182417] ehci_hcd 0000:04:00.3: park 0 [ 1.182419] ehci_hcd 0000:04:00.3: applying MosChip frame-index workaround [ 1.182808] ehci_hcd 0000:04:00.3: reset command 0010006 (park)=0 ithresh=1 period=512 Reset HALT [ 1.182869] ehci_hcd 0000:04:00.3: Enabling legacy PCI PM [ 1.182882] ehci_hcd 0000:04:00.3: ...powerup ports... [ 1.203201] ehci_hcd 0000:04:00.3: MWI active [ 1.203205] ehci_hcd 0000:04:00.3: supports USB remote wakeup [ 1.203219] ehci_hcd 0000:04:00.3: irq 29, io mem 0xf9afb000 [ 1.203229] ehci_hcd 0000:04:00.3: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT [ 1.203239] ehci_hcd 0000:04:00.3: init command 0010005 (park)=0 ithresh=1 period=512 RUN [ 1.208311] Setting capacity to 1048576 [ 1.208322] xvda1: detected capacity change from 0 to 536870912 [ 1.208669] Setting capacity to 8388608 [ 1.208675] xvda2: detected capacity change from 0 to 4294967296 [ 1.209073] ehci_hcd 0000:04:00.3: USB 2.0 started, EHCI 1.00 [ 1.209096] usb usb2: default language 0x0409 [ 1.209102] usb usb2: udev 1, busnum 2, minor = 128 [ 1.209104] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.209109] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.209114] usb usb2: Product: EHCI Host Controller [ 1.209117] usb usb2: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ehci_hcd [ 1.209122] usb usb2: SerialNumber: 0000:04:00.3 [ 1.209175] usb usb2: usb_probe_device [ 1.209178] usb usb2: configuration #1 chosen from 1 choice [ 1.209183] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 1.209219] hub 2-0:1.0: usb_probe_interface [ 1.209221] hub 2-0:1.0: usb_probe_interface - got id [ 1.209223] hub 2-0:1.0: USB hub found [ 1.209229] hub 2-0:1.0: 1 port detected [ 1.209233] hub 2-0:1.0: standalone hub [ 1.209234] hub 2-0:1.0: individual port power switching [ 1.209236] hub 2-0:1.0: individual port over-current protection [ 1.209238] hub 2-0:1.0: power on to power good time: 20ms [ 1.209242] hub 2-0:1.0: local power source is good [ 1.209244] hub 2-0:1.0: enabling power on all ports [ 1.209272] drivers/usb/core/inode.c: creating file '001' [ 1.209444] ehci_hcd 0000:04:00.5: enabling device (0000 -> 0002) [ 1.209727] ehci_hcd 0000:04:00.5: Xen PCI mapped GSI42 to IRQ31 [ 1.209853] ehci_hcd 0000:04:00.5: setting latency timer to 64 [ 1.209882] ehci_hcd 0000:04:00.5: EHCI Host Controller [ 1.209890] drivers/usb/core/inode.c: creating file '003' [ 1.209949] ehci_hcd 0000:04:00.5: new USB bus registered, assigned bus number 3 [ 1.209962] ehci_hcd 0000:04:00.5: reset hcs_params 0x1191 dbg=0 cc=1 pcc=1 ports=1 [ 1.209966] ehci_hcd 0000:04:00.5: reset portroute 0 [ 1.209971] ehci_hcd 0000:04:00.5: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park [ 1.210022] ehci_hcd 0000:04:00.5: park 0 [ 1.210024] ehci_hcd 0000:04:00.5: applying MosChip frame-index workaround [ 1.210056] ehci_hcd 0000:04:00.5: reset command 0010006 (park)=0 ithresh=1 period=512 Reset HALT [ 1.210056] ehci_hcd 0000:04:00.5: Enabling legacy PCI PM [ 1.210269] ehci_hcd 0000:04:00.5: ...powerup ports... [ 1.231305] ehci_hcd 0000:04:00.5: MWI active [ 1.231309] ehci_hcd 0000:04:00.5: supports USB remote wakeup [ 1.231329] ehci_hcd 0000:04:00.5: irq 31, io mem 0xf9afd000 [ 1.231342] ehci_hcd 0000:04:00.5: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT [ 1.231353] ehci_hcd 0000:04:00.5: init command 0010005 (park)=0 ithresh=1 period=512 RUN [ 1.237095] ehci_hcd 0000:04:00.5: USB 2.0 started, EHCI 1.00 [ 1.237145] usb usb3: default language 0x0409 [ 1.237150] usb usb3: udev 1, busnum 3, minor = 256 [ 1.237153] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.237157] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.237162] usb usb3: Product: EHCI Host Controller [ 1.237165] usb usb3: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ehci_hcd [ 1.237170] usb usb3: SerialNumber: 0000:04:00.5 [ 1.237269] usb usb3: usb_probe_device [ 1.237272] usb usb3: configuration #1 chosen from 1 choice [ 1.237279] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 1.237325] hub 3-0:1.0: usb_probe_interface [ 1.237327] hub 3-0:1.0: usb_probe_interface - got id [ 1.237329] hub 3-0:1.0: USB hub found [ 1.237336] hub 3-0:1.0: 1 port detected [ 1.237340] hub 3-0:1.0: standalone hub [ 1.237342] hub 3-0:1.0: individual port power switching [ 1.237344] hub 3-0:1.0: individual port over-current protection [ 1.237345] hub 3-0:1.0: power on to power good time: 20ms [ 1.237349] hub 3-0:1.0: local power source is good [ 1.237351] hub 3-0:1.0: enabling power on all ports [ 1.237384] drivers/usb/core/inode.c: creating file '001' [ 1.237486] ehci_hcd 0000:04:00.7: enabling device (0000 -> 0002) [ 1.237640] ehci_hcd 0000:04:00.7: Xen PCI mapped GSI43 to IRQ32 [ 1.237762] ehci_hcd 0000:04:00.7: setting latency timer to 64 [ 1.237792] ehci_hcd 0000:04:00.7: EHCI Host Controller [ 1.237802] drivers/usb/core/inode.c: creating file '004' [ 1.237869] ehci_hcd 0000:04:00.7: new USB bus registered, assigned bus number 4 [ 1.237881] ehci_hcd 0000:04:00.7: reset hcs_params 0x1191 dbg=0 cc=1 pcc=1 ports=1 [ 1.237885] ehci_hcd 0000:04:00.7: reset portroute 0 [ 1.237890] ehci_hcd 0000:04:00.7: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park [ 1.237937] ehci_hcd 0000:04:00.7: park 0 [ 1.237939] ehci_hcd 0000:04:00.7: applying MosChip frame-index workaround [ 1.238074] ehci_hcd 0000:04:00.7: reset command 0010006 (park)=0 ithresh=1 period=512 Reset HALT [ 1.238074] ehci_hcd 0000:04:00.7: Enabling legacy PCI PM [ 1.238074] ehci_hcd 0000:04:00.7: ...powerup ports... [ 1.258192] ehci_hcd 0000:04:00.7: MWI active [ 1.258196] ehci_hcd 0000:04:00.7: supports USB remote wakeup [ 1.258209] ehci_hcd 0000:04:00.7: irq 32, io mem 0xf9aff000 [ 1.258218] ehci_hcd 0000:04:00.7: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT [ 1.258229] ehci_hcd 0000:04:00.7: init command 0010005 (park)=0 ithresh=1 period=512 RUN [ 1.264093] ehci_hcd 0000:04:00.7: USB 2.0 started, EHCI 1.00 [ 1.264121] usb usb4: default language 0x0409 [ 1.264126] usb usb4: udev 1, busnum 4, minor = 384 [ 1.264128] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.264132] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.264137] usb usb4: Product: EHCI Host Controller [ 1.264140] usb usb4: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ehci_hcd [ 1.264145] usb usb4: SerialNumber: 0000:04:00.7 [ 1.264222] usb usb4: usb_probe_device [ 1.264224] usb usb4: configuration #1 chosen from 1 choice [ 1.264229] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 1.264270] hub 4-0:1.0: usb_probe_interface [ 1.264272] hub 4-0:1.0: usb_probe_interface - got id [ 1.264274] hub 4-0:1.0: USB hub found [ 1.264281] hub 4-0:1.0: 1 port detected [ 1.264285] hub 4-0:1.0: standalone hub [ 1.264286] hub 4-0:1.0: individual port power switching [ 1.264288] hub 4-0:1.0: individual port over-current protection [ 1.264290] hub 4-0:1.0: power on to power good time: 20ms [ 1.264293] hub 4-0:1.0: local power source is good [ 1.264295] hub 4-0:1.0: enabling power on all ports [ 1.264308] drivers/usb/core/inode.c: creating file '001' [ 1.264358] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.264362] ohci_hcd: block sizes: ed 80 td 96 [ 1.264424] ohci_hcd 0000:04:00.0: enabling device (0000 -> 0002) [ 1.265073] xen_map_pirq_gsi: returning irq 28 for gsi 40 [ 1.265073] ohci_hcd 0000:04:00.0: Xen PCI mapped GSI40 to IRQ28 [ 1.384621] ehci_hcd 0000:04:00.1: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 1.384626] hub 1-0:1.0: port 1: status 0501 change 0001 [ 1.384637] ehci_hcd 0000:04:00.3: GetStatus port:1 status 001403 0 ACK POWER sig=k CSC CONNECT [ 1.384640] hub 2-0:1.0: port 1: status 0501 change 0001 [ 1.384650] ehci_hcd 0000:04:00.5: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT [ 1.384654] hub 3-0:1.0: port 1: status 0501 change 0001 [ 1.384674] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 1.384791] ohci_hcd 0000:04:00.0: setting latency timer to 64 [ 1.384819] ohci_hcd 0000:04:00.0: OHCI Host Controller [ 1.384830] drivers/usb/core/inode.c: creating file '005' [ 1.384908] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 5 [ 1.384956] ohci_hcd 0000:04:00.0: created debug files [ 1.384964] ohci_hcd 0000:04:00.0: irq 28, io mem 0xf9af8000 [ 1.439172] ohci_hcd 0000:04:00.0: OHCI controller state [ 1.439177] ohci_hcd 0000:04:00.0: OHCI 1.0, NO legacy support registers [ 1.439181] ohci_hcd 0000:04:00.0: control 0x083 HCFS=operational CBSR=3 [ 1.439184] ohci_hcd 0000:04:00.0: cmdstatus 0x00000 SOC=0 [ 1.439188] ohci_hcd 0000:04:00.0: intrstatus 0x00000000 [ 1.439191] ohci_hcd 0000:04:00.0: intrenable 0x8000005a MIE RHSC UE RD WDH [ 1.439201] ohci_hcd 0000:04:00.0: hcca frame #0000 [ 1.439205] ohci_hcd 0000:04:00.0: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) [ 1.439209] ohci_hcd 0000:04:00.0: roothub.b 00000000 PPCM=0000 DR=0000 [ 1.439212] ohci_hcd 0000:04:00.0: roothub.status 00008000 DRWE [ 1.439216] ohci_hcd 0000:04:00.0: roothub.portstatus [0] 0x00030100 PESC CSC PPS [ 1.439228] usb usb5: default language 0x0409 [ 1.439233] usb usb5: udev 1, busnum 5, minor = 512 [ 1.439235] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.439249] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.439254] usb usb5: Product: OHCI Host Controller [ 1.439258] usb usb5: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ohci_hcd [ 1.439263] usb usb5: SerialNumber: 0000:04:00.0 [ 1.439336] usb usb5: usb_probe_device [ 1.439338] usb usb5: configuration #1 chosen from 1 choice [ 1.439344] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 1.439385] hub 5-0:1.0: usb_probe_interface [ 1.439387] hub 5-0:1.0: usb_probe_interface - got id [ 1.439389] hub 5-0:1.0: USB hub found [ 1.439398] hub 5-0:1.0: 1 port detected [ 1.439402] hub 5-0:1.0: standalone hub [ 1.439404] hub 5-0:1.0: no power switching (usb 1.0) [ 1.439405] hub 5-0:1.0: global over-current protection [ 1.439407] hub 5-0:1.0: power on to power good time: 4ms [ 1.439412] hub 5-0:1.0: local power source is good [ 1.439414] hub 5-0:1.0: no over-current condition exists [ 1.439416] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 1.439426] drivers/usb/core/inode.c: creating file '001' [ 1.439445] ehci_hcd 0000:04:00.1: HS companion for 0000:04:00.0 [ 1.439448] ehci_hcd 0000:04:00.3: HS companion for 0000:04:00.0 [ 1.439451] ehci_hcd 0000:04:00.5: HS companion for 0000:04:00.0 [ 1.439454] ehci_hcd 0000:04:00.7: HS companion for 0000:04:00.0 [ 1.439536] ohci_hcd 0000:04:00.2: enabling device (0000 -> 0002) [ 1.440051] xen_map_pirq_gsi: returning irq 29 for gsi 41 [ 1.440051] ohci_hcd 0000:04:00.2: Xen PCI mapped GSI41 to IRQ29 [ 1.469993] ohci_hcd 0000:04:00.2: setting latency timer to 64 [ 1.470018] ohci_hcd 0000:04:00.2: OHCI Host Controller [ 1.470042] drivers/usb/core/inode.c: creating file '006' [ 1.470108] ohci_hcd 0000:04:00.2: new USB bus registered, assigned bus number 6 [ 1.470143] ohci_hcd 0000:04:00.2: created debug files [ 1.470151] ohci_hcd 0000:04:00.2: irq 29, io mem 0xf9afa000 [ 1.484105] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 1.484113] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 1.525118] ohci_hcd 0000:04:00.2: OHCI controller state [ 1.525123] ohci_hcd 0000:04:00.2: OHCI 1.0, NO legacy support registers [ 1.525127] ohci_hcd 0000:04:00.2: control 0x083 HCFS=operational CBSR=3 [ 1.525131] ohci_hcd 0000:04:00.2: cmdstatus 0x00000 SOC=0 [ 1.525134] ohci_hcd 0000:04:00.2: intrstatus 0x00000000 [ 1.525138] ohci_hcd 0000:04:00.2: intrenable 0x8000005a MIE RHSC UE RD WDH [ 1.525148] ohci_hcd 0000:04:00.2: hcca frame #0000 [ 1.525152] ohci_hcd 0000:04:00.2: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) [ 1.525155] ohci_hcd 0000:04:00.2: roothub.b 00000000 PPCM=0000 DR=0000 [ 1.525158] ohci_hcd 0000:04:00.2: roothub.status 00008000 DRWE [ 1.525162] ohci_hcd 0000:04:00.2: roothub.portstatus [0] 0x00030100 PESC CSC PPS [ 1.525178] usb usb6: default language 0x0409 [ 1.525183] usb usb6: udev 1, busnum 6, minor = 640 [ 1.525185] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.525195] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.525200] usb usb6: Product: OHCI Host Controller [ 1.525203] usb usb6: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ohci_hcd [ 1.525208] usb usb6: SerialNumber: 0000:04:00.2 [ 1.525319] usb usb6: usb_probe_device [ 1.525322] usb usb6: configuration #1 chosen from 1 choice [ 1.525328] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 1.525377] hub 6-0:1.0: usb_probe_interface [ 1.525379] hub 6-0:1.0: usb_probe_interface - got id [ 1.525381] hub 6-0:1.0: USB hub found [ 1.525390] hub 6-0:1.0: 1 port detected [ 1.525394] hub 6-0:1.0: standalone hub [ 1.525395] hub 6-0:1.0: no power switching (usb 1.0) [ 1.525397] hub 6-0:1.0: global over-current protection [ 1.525399] hub 6-0:1.0: power on to power good time: 4ms [ 1.525404] hub 6-0:1.0: local power source is good [ 1.525406] hub 6-0:1.0: no over-current condition exists [ 1.525408] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 1.525420] drivers/usb/core/inode.c: creating file '001' [ 1.525442] ehci_hcd 0000:04:00.1: HS companion for 0000:04:00.2 [ 1.525445] ehci_hcd 0000:04:00.3: HS companion for 0000:04:00.2 [ 1.525448] ehci_hcd 0000:04:00.5: HS companion for 0000:04:00.2 [ 1.525451] ehci_hcd 0000:04:00.7: HS companion for 0000:04:00.2 [ 1.525555] ohci_hcd 0000:04:00.4: enabling device (0000 -> 0002) [ 1.526051] xen_map_pirq_gsi: returning irq 31 for gsi 42 [ 1.526051] ohci_hcd 0000:04:00.4: Xen PCI mapped GSI42 to IRQ31 [ 1.556747] ohci_hcd 0000:04:00.4: setting latency timer to 64 [ 1.556747] ohci_hcd 0000:04:00.4: OHCI Host Controller [ 1.557617] ehci_hcd 0000:04:00.1: port 1 high speed [ 1.557622] ehci_hcd 0000:04:00.1: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 1.557633] ohci_hcd 0000:04:00.0: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS [ 1.557684] drivers/usb/core/inode.c: creating file '007' [ 1.557762] ohci_hcd 0000:04:00.4: new USB bus registered, assigned bus number 7 [ 1.557810] ohci_hcd 0000:04:00.4: created debug files [ 1.557819] ohci_hcd 0000:04:00.4: irq 31, io mem 0xf9afc000 [ 1.608102] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 1.612140] ohci_hcd 0000:04:00.4: OHCI controller state [ 1.612143] ohci_hcd 0000:04:00.4: OHCI 1.0, NO legacy support registers [ 1.612147] ohci_hcd 0000:04:00.4: control 0x083 HCFS=operational CBSR=3 [ 1.612151] ohci_hcd 0000:04:00.4: cmdstatus 0x00000 SOC=0 [ 1.612154] ohci_hcd 0000:04:00.4: intrstatus 0x00000000 [ 1.612158] ohci_hcd 0000:04:00.4: intrenable 0x8000005a MIE RHSC UE RD WDH [ 1.612168] ohci_hcd 0000:04:00.4: hcca frame #0000 [ 1.612172] ohci_hcd 0000:04:00.4: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) [ 1.612175] ohci_hcd 0000:04:00.4: roothub.b 00000000 PPCM=0000 DR=0000 [ 1.612178] ohci_hcd 0000:04:00.4: roothub.status 00008000 DRWE [ 1.612182] ohci_hcd 0000:04:00.4: roothub.portstatus [0] 0x00030100 PESC CSC PPS [ 1.612197] usb usb7: default language 0x0409 [ 1.612202] usb usb7: udev 1, busnum 7, minor = 768 [ 1.612204] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.612210] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.612215] usb usb7: Product: OHCI Host Controller [ 1.612218] usb usb7: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ohci_hcd [ 1.612223] usb usb7: SerialNumber: 0000:04:00.4 [ 1.612299] usb usb7: usb_probe_device [ 1.612301] usb usb7: configuration #1 chosen from 1 choice [ 1.612307] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 1.612346] hub 7-0:1.0: usb_probe_interface [ 1.612348] hub 7-0:1.0: usb_probe_interface - got id [ 1.612350] hub 7-0:1.0: USB hub found [ 1.612358] hub 7-0:1.0: 1 port detected [ 1.612362] hub 7-0:1.0: standalone hub [ 1.612364] hub 7-0:1.0: no power switching (usb 1.0) [ 1.612365] hub 7-0:1.0: global over-current protection [ 1.612367] hub 7-0:1.0: power on to power good time: 4ms [ 1.612372] hub 7-0:1.0: local power source is good [ 1.612374] hub 7-0:1.0: no over-current condition exists [ 1.612376] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 1.612387] drivers/usb/core/inode.c: creating file '001' [ 1.612405] ehci_hcd 0000:04:00.1: HS companion for 0000:04:00.4 [ 1.612408] ehci_hcd 0000:04:00.3: HS companion for 0000:04:00.4 [ 1.612411] ehci_hcd 0000:04:00.5: HS companion for 0000:04:00.4 [ 1.612414] ehci_hcd 0000:04:00.7: HS companion for 0000:04:00.4 [ 1.612484] ohci_hcd 0000:04:00.6: enabling device (0000 -> 0002) [ 1.613051] xen_map_pirq_gsi: returning irq 32 for gsi 43 [ 1.613051] ohci_hcd 0000:04:00.6: Xen PCI mapped GSI43 to IRQ32 [ 1.642210] ohci_hcd 0000:04:00.6: setting latency timer to 64 [ 1.642234] ohci_hcd 0000:04:00.6: OHCI Host Controller [ 1.642271] ohci_hcd 0000:04:00.2: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS [ 1.642321] drivers/usb/core/inode.c: creating file '008' [ 1.642374] ohci_hcd 0000:04:00.6: new USB bus registered, assigned bus number 8 [ 1.642408] ohci_hcd 0000:04:00.6: created debug files [ 1.642417] ohci_hcd 0000:04:00.6: irq 32, io mem 0xf9afe000 [ 1.663281] ehci_hcd 0000:04:00.1: port 1 high speed [ 1.663286] ehci_hcd 0000:04:00.1: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 1.669335] blkfront: xvdb1: flush diskcache: enabled [ 1.697132] ohci_hcd 0000:04:00.6: OHCI controller state [ 1.697138] ohci_hcd 0000:04:00.6: OHCI 1.0, NO legacy support registers [ 1.697142] ohci_hcd 0000:04:00.6: control 0x083 HCFS=operational CBSR=3 [ 1.697145] ohci_hcd 0000:04:00.6: cmdstatus 0x00000 SOC=0 [ 1.697149] ohci_hcd 0000:04:00.6: intrstatus 0x00000000 [ 1.697153] ohci_hcd 0000:04:00.6: intrenable 0x8000005a MIE RHSC UE RD WDH [ 1.697168] ohci_hcd 0000:04:00.6: hcca frame #0000 [ 1.697172] ohci_hcd 0000:04:00.6: roothub.a 02000201 POTPGT=2 NPS NDP=1(1) [ 1.697176] ohci_hcd 0000:04:00.6: roothub.b 00000000 PPCM=0000 DR=0000 [ 1.697179] ohci_hcd 0000:04:00.6: roothub.status 00008000 DRWE [ 1.697183] ohci_hcd 0000:04:00.6: roothub.portstatus [0] 0x00000100 PPS [ 1.697200] usb usb8: default language 0x0409 [ 1.697207] usb usb8: udev 1, busnum 8, minor = 896 [ 1.697209] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 1.697219] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.697224] usb usb8: Product: OHCI Host Controller [ 1.697228] usb usb8: Manufacturer: Linux 3.2.0-rc2konrad-testing-20111123+ ohci_hcd [ 1.697233] usb usb8: SerialNumber: 0000:04:00.6 [ 1.697341] usb usb8: usb_probe_device [ 1.697344] usb usb8: configuration #1 chosen from 1 choice [ 1.697350] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 1.697400] hub 8-0:1.0: usb_probe_interface [ 1.697403] hub 8-0:1.0: usb_probe_interface - got id [ 1.697405] hub 8-0:1.0: USB hub found [ 1.697414] hub 8-0:1.0: 1 port detected [ 1.697418] hub 8-0:1.0: standalone hub [ 1.697419] hub 8-0:1.0: no power switching (usb 1.0) [ 1.697421] hub 8-0:1.0: global over-current protection [ 1.697423] hub 8-0:1.0: power on to power good time: 4ms [ 1.697428] hub 8-0:1.0: local power source is good [ 1.697430] hub 8-0:1.0: no over-current condition exists [ 1.697433] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 1.697444] drivers/usb/core/inode.c: creating file '001' [ 1.697469] ehci_hcd 0000:04:00.1: HS companion for 0000:04:00.6 [ 1.697473] ehci_hcd 0000:04:00.3: HS companion for 0000:04:00.6 [ 1.697476] ehci_hcd 0000:04:00.5: HS companion for 0000:04:00.6 [ 1.697478] ehci_hcd 0000:04:00.7: HS companion for 0000:04:00.6 [ 1.697520] uhci_hcd: USB Universal Host Controller Interface driver [ 1.697621] usbcore: registered new interface driver usblp [ 1.697626] Initializing USB Mass Storage driver... [ 1.697675] usbcore: registered new interface driver usb-storage [ 1.697679] USB Mass Storage support registered. [ 1.697725] usbcore: registered new interface driver libusual [ 1.697802] usbcore: registered new interface driver usbserial [ 1.697807] usbserial: USB Serial Driver core [ 1.697840] USB Serial support registered for cp210x [ 1.697879] usbcore: registered new interface driver cp210x [ 1.697883] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver [ 1.697913] USB Serial support registered for DeLorme Earthmate USB [ 1.697944] USB Serial support registered for HID->COM RS232 Adapter [ 1.697980] USB Serial support registered for Nokia CA-42 V2 Adapter [ 1.698015] usbcore: registered new interface driver cypress [ 1.698019] cypress_m8: v1.10:Cypress USB to Serial Driver [ 1.698050] USB Serial support registered for Moschip 2 port adapter [ 1.698051] mos7720: 2.1:Moschip USB Serial Driver [ 1.698102] usbcore: registered new interface driver moschip7720 [ 1.698137] USB Serial support registered for Moschip 7840/7820 USB Serial Driver [ 1.698142] mos7840: 1.3.2:Moschip 7840/7820 USB Serial Driver [ 1.698179] usbcore: registered new interface driver mos7840 [ 1.698291] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 1.699071] i8042: No controller found [ 1.699229] mousedev: PS/2 mouse device common for all mice [ 1.719449] ohci_hcd 0000:04:00.4: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS [ 1.739645] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 1.739726] rtc_cmos: probe of rtc_cmos failed with error -38 [ 1.739961] lirc_dev: IR Remote Control driver registered, major 251 [ 1.739966] IR NEC protocol handler initialized [ 1.739970] IR RC5(x) protocol handler initialized [ 1.739973] IR RC6 protocol handler initialized [ 1.739977] IR JVC protocol handler initialized [ 1.739980] IR Sony protocol handler initialized [ 1.739984] IR RC5 (streamzap) protocol handler initialized [ 1.739987] IR MCE Keyboard/mouse protocol handler initialized [ 1.739991] IR LIRC bridge handler initialized [ 1.739994] Linux video capture interface: v2.00 [ 1.740048] i2c-core: driver [tuner] using legacy suspend method [ 1.740051] i2c-core: driver [tuner] using legacy resume method [ 1.740123] i2c-core: driver [msp3400] using legacy suspend method [ 1.740128] i2c-core: driver [msp3400] using legacy resume method [ 1.740208] cx231xx v4l2 driver loaded. [ 1.740245] usbcore: registered new interface driver cx231xx [ 1.740285] usbcore: registered new interface driver usbvision [ 1.740290] USBVision USB Video Device Driver for Linux : 0.9.11 [ 1.740365] usbcore: registered new interface driver pvrusb2 [ 1.740370] pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner [ 1.741066] pvrusb2: Debug mask is 31 (0x1f) [ 1.756299] usbcore: registered new interface driver zr364xx [ 1.756305] zr364xx: Zoran 364xx [ 1.756339] usbcore: registered new interface driver stkwebcam [ 1.756344] sn9c102: V4L2 driver for SN9C1xx PC Camera Controllers v1:1.48 [ 1.756380] usbcore: registered new interface driver sn9c102 [ 1.756384] et61x251: V4L2 driver for ET61X[12]51 PC Camera Controllers v1.1.10 [ 1.756418] usbcore: registered new interface driver et61x251 [ 1.756456] usbcore: registered new interface driver Philips webcam [ 1.756461] gspca_main: v2.14.0 registered [ 1.756494] usbcore: registered new interface driver hdpvr [ 1.756527] usbcore: registered new interface driver s2255 [ 1.756680] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01 [ 1.756754] wdt: Xen WatchDog Timer Driver v0.01 [ 1.756854] wdt: initialized (timeout=60s, nowayout=0) [ 1.756958] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com [ 1.757166] EFI Variables Facility v0.08 2004-May-17 [ 1.757406] usb 1-1: udev 2, busnum 1, minor = 1 [ 1.757408] usb 1-1: New USB device found, idVendor=eb1a, idProduct=2860 [ 1.757414] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 1.757496] usb 1-1: usb_probe_device [ 1.757499] usb 1-1: configuration #1 chosen from 1 choice [ 1.757649] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 1.757727] drivers/usb/core/inode.c: creating file '002' [ 1.757739] hub 2-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 1.757745] hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 1.757752] ehci_hcd 0000:04:00.3: port 1 low speed --> companion [ 1.758245] usbcore: registered new interface driver usbhid [ 1.758259] usbhid: USB HID core driver [ 1.760300] usbcore: registered new interface driver snd-usb-audio [ 1.760346] usbcore: registered new interface driver snd-ua101 [ 1.760381] usbcore: registered new interface driver snd-usb-usx2y [ 1.760419] usbcore: registered new interface driver snd-usb-us122l [ 1.760456] usbcore: registered new interface driver snd-usb-caiaq [ 1.760494] usbcore: registered new interface driver snd-usb-6fire [ 1.760500] ALSA device list: [ 1.760503] No soundcards found. [ 1.760525] Netfilter messages via NETLINK v0.30. [ 1.760544] nf_conntrack version 0.5.0 (3364 buckets, 13456 max) [ 1.760689] ctnetlink v0.93: registering with nfnetlink. [ 1.760803] xt_time: kernel timezone is -0000 [ 1.760809] ip_set: protocol 6 [ 1.760822] IPVS: Registered protocols () [ 1.760884] IPVS: Connection hash table configured (size=4096, memory=64Kbytes) [ 1.760941] IPVS: Creating netns size=1304 id=0 [ 1.760946] IPVS: ipvs loaded. [ 1.761277] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.761309] TCP cubic registered [ 1.761314] NET: Registered protocol family 17 [ 1.761340] Bridge firewalling registered [ 1.761345] Ebtables v2.0 registered [ 1.761356] Registering the dns_resolver key type [ 1.761487] registered taskstats version 1 [ 1.762844] XENBUS: Device with no driver: device/console/0 [ 1.762854] Magic number: 1:252:3141 [ 1.762892] console [netcon0] enabled [ 1.762895] netconsole: network logging started [ 1.763239] Freeing unused kernel memory: 780k freed [ 1.763432] Write protecting the kernel read-only data: 14336k [ 1.768067] Freeing unused kernel memory: 1656k freed [ 1.768806] Freeing unused kernel memory: 1140k freed [ 1.808096] ehci_hcd 0000:04:00.3: GetStatus port:1 status 003402 0 ACK POWER OWNER sig=k CSC [ 1.808121] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 1.808127] hub 3-0:1.0: port 1, status 0501, change 0000, 480 Mb/s [ 1.859247] ehci_hcd 0000:04:00.5: port 1 high speed [ 1.859253] ehci_hcd 0000:04:00.5: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 1.910091] usb 3-1: new high-speed USB device number 2 using ehci_hcd [ 1.961251] ehci_hcd 0000:04:00.5: port 1 high speed [ 1.961257] ehci_hcd 0000:04:00.5: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT [ 2.027941] usb 3-1: default language 0x0409 [ 2.028819] usb 3-1: udev 2, busnum 3, minor = 257 [ 2.028831] usb 3-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.028859] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.028865] usb 3-1: Product: USB2.0 Hub [ 2.028917] usb 3-1: usb_probe_device [ 2.028920] usb 3-1: configuration #1 chosen from 1 choice [ 2.029468] usb 3-1: adding 3-1:1.0 (config #1, interface 0) [ 2.029542] hub 3-1:1.0: usb_probe_interface [ 2.029544] hub 3-1:1.0: usb_probe_interface - got id [ 2.029546] hub 3-1:1.0: USB hub found [ 2.030199] hub 3-1:1.0: 4 ports detected [ 2.030221] hub 3-1:1.0: standalone hub [ 2.030223] hub 3-1:1.0: ganged power switching [ 2.030225] hub 3-1:1.0: global over-current protection [ 2.030226] hub 3-1:1.0: Single TT [ 2.030228] hub 3-1:1.0: TT requires at most 32 FS bit times (2664 ns) [ 2.030230] hub 3-1:1.0: Port indicators are supported [ 2.030232] hub 3-1:1.0: power on to power good time: 100ms [ 2.031377] hub 3-1:1.0: local power source is good [ 2.031380] hub 3-1:1.0: no over-current condition exists [ 2.031387] hub 3-1:1.0: enabling power on all ports [ 2.033707] drivers/usb/core/inode.c: creating file '002' [ 2.033725] hub 5-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.033728] hub 6-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 2.033734] ohci_hcd 0000:04:00.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS [ 2.033738] hub 6-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s [ 2.135814] hub 3-1:1.0: port 4: status 0101 change 0001 [ 2.137106] hub 6-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 [ 2.199161] ohci_hcd 0000:04:00.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS [ 2.236176] usb 3-1: link qh256-0001/ffff880019567300 start 1 [1/0 us] [ 2.250164] usb 6-1: new low-speed USB device number 2 using ohci_hcd [ 2.314170] ohci_hcd 0000:04:00.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS [ 2.361469] EXT4-fs (xvda2): mounted filesystem with ordered data mode. Opts: (null) [ 2.385109] usb 6-1: skipped 1 descriptor after interface [ 2.387198] usb 6-1: default language 0x0409 [ 2.392163] ohci_hcd 0000:04:00.2: urb ffff8800190fc180 path 1 ep0in 5ed60000 cc 5 --> status -62 [ 2.394084] ohci_hcd 0000:04:00.2: urb ffff8800190fc180 path 1 ep0in 5fd60000 cc 5 --> status -62 [ 2.394106] usb 6-1: udev 2, busnum 6, minor = 641 [ 2.394108] usb 6-1: New USB device found, idVendor=10cf, idProduct=5500 [ 2.394119] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.394124] usb 6-1: Product: USB K8055 [ 2.394172] usb 6-1: usb_probe_device [ 2.394176] usb 6-1: configuration #1 chosen from 1 choice [ 2.398207] usb 6-1: adding 6-1:1.0 (config #1, interface 0) [ 2.398256] usbhid 6-1:1.0: usb_probe_interface [ 2.398259] usbhid 6-1:1.0: usb_probe_interface - got id [ 2.405230] usbhid 6-1:1.0: looking for a minor, starting at 96 [ 2.405259] generic-usb 0003:10CF:5500.0001: hiddev0,hidraw0: USB HID v1.00 Device [USB K8055] on usb-0000:04:00.2-1/input0 [ 2.405281] drivers/usb/core/inode.c: creating file '002' [ 2.405298] hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 2.405306] hub 8-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.405308] hub 7-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.405311] hub 6-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 2.405318] hub 3-1:1.0: state 7 ports 4 chg 0010 evt 0000 [ 2.405990] hub 3-1:1.0: port 4, status 0101, change 0000, 12 Mb/s [ 2.469624] usb 3-1.4: new high-speed USB device number 3 using ehci_hcd [ 2.481664] hub 3-1:1.0: port 4 not reset yet, waiting 10ms [ 2.557537] usb 3-1.4: skipped 4 descriptors after interface [ 2.557540] usb 3-1.4: skipped 2 descriptors after interface [ 2.557542] usb 3-1.4: skipped 1 descriptor after endpoint [ 2.557544] usb 3-1.4: skipped 2 descriptors after interface [ 2.557546] usb 3-1.4: skipped 1 descriptor after endpoint [ 2.557548] usb 3-1.4: skipped 2 descriptors after interface [ 2.557550] usb 3-1.4: skipped 1 descriptor after endpoint [ 2.557552] usb 3-1.4: skipped 2 descriptors after interface [ 2.557555] usb 3-1.4: skipped 1 descriptor after endpoint [ 2.557556] usb 3-1.4: skipped 2 descriptors after interface [ 2.557558] usb 3-1.4: skipped 1 descriptor after endpoint [ 2.558057] usb 3-1.4: default language 0x0409 [ 2.565562] usb 3-1.4: udev 3, busnum 3, minor = 258 [ 2.565580] usb 3-1.4: New USB device found, idVendor=2304, idProduct=0208 [ 2.565590] usb 3-1.4: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 2.565595] usb 3-1.4: Product: PCTV USB2 PAL [ 2.565599] usb 3-1.4: Manufacturer: Pinnacle Systems GmbH [ 2.565650] usb 3-1.4: usb_probe_device [ 2.565653] usb 3-1.4: configuration #1 chosen from 1 choice [ 2.565826] usb 3-1.4: adding 3-1.4:1.0 (config #1, interface 0) [ 2.565880] usb 3-1.4: adding 3-1.4:1.1 (config #1, interface 1) [ 2.565903] snd-usb-audio 3-1.4:1.1: usb_probe_interface [ 2.565906] snd-usb-audio 3-1.4:1.1: usb_probe_interface - got id [ 3.144196] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 1 [ 3.144287] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 2 [ 3.144379] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 3 [ 3.144504] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 4 [ 3.144628] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 5 [ 3.144753] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 6 [ 3.144879] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 7 [ 3.145004] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 8 [ 3.145129] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 9 [ 3.145254] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 10 [ 3.145379] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 11 [ 3.145503] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 12 [ 3.145628] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 13 [ 3.145754] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 14 [ 3.145878] ehci_hcd 0000:04:00.5: detected XactErr len 0/255 retry 15 [ 4.593945] udevd[1267]: starting version 172 [ 5.133300] em28xx 1-1:1.0: usb_probe_interface [ 5.133309] em28xx 1-1:1.0: usb_probe_interface - got id [ 5.133316] em28xx: New device @ 480 Mbps (eb1a:2860, interface 0, class 0) [ 5.133696] em28xx #0: chip ID is em2860 [ 5.205176] em28xx #0: board has no eeprom [ 5.208180] em28xx #0: Identified as Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker / Kworld DVD Maker 2 (card=9) [ 5.435919] saa7115 0-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #0) [ 5.885233] em28xx #0: Config register raw data: 0x00 [ 5.914754] em28xx #0: v4l2 driver version 0.1.3 [ 6.222250] em28xx #0: V4L2 video device registered as video0 [ 6.222260] em28xx #0: V4L2 VBI device registered as vbi0 [ 7.565280] usb 3-1.4: khubd timed out on ep0in len=0/255 [ 12.565275] usb 3-1.4: khubd timed out on ep0in len=0/2 [ 17.565297] usb 3-1.4: khubd timed out on ep0in len=0/255 [ 17.572875] usb 3-1.4: adding 3-1.4:1.2 (config #1, interface 2) [ 17.572898] drivers/usb/core/inode.c: creating file '003' [ 17.572921] hub 3-1:1.0: state 7 ports 4 chg 0000 evt 0010 [ 17.573087] em28xx 3-1.4:1.0: usb_probe_interface [ 17.573091] em28xx 3-1.4:1.0: usb_probe_interface - got id [ 17.573100] em28xx: New device Pinnacle Systems GmbH PCTV USB2 PAL @ 480 Mbps (2304:0208, interface 0, class 0) [ 17.573432] em28xx #1: chip ID is em2820 (or em2710) [ 17.687880] em28xx #1: i2c eeprom 00: 1a eb 67 95 04 23 08 02 10 00 1e 03 98 1e 6a 2e [ 17.687995] em28xx #1: i2c eeprom 10: 00 00 06 57 6e 00 00 00 8e 00 00 00 07 00 00 00 [ 17.688057] em28xx #1: i2c eeprom 20: 16 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688077] em28xx #1: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 01 00 00 00 00 00 00 [ 17.688096] em28xx #1: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688115] em28xx #1: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688134] em28xx #1: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 2e 03 50 00 69 00 [ 17.688153] em28xx #1: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00 [ 17.688172] em28xx #1: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 20 00 47 00 [ 17.688190] em28xx #1: i2c eeprom 90: 6d 00 62 00 48 00 00 00 1e 03 50 00 43 00 54 00 [ 17.688210] em28xx #1: i2c eeprom a0: 56 00 20 00 55 00 53 00 42 00 32 00 20 00 50 00 [ 17.688229] em28xx #1: i2c eeprom b0: 41 00 4c 00 00 00 06 03 31 00 00 00 00 00 00 00 [ 17.688248] em28xx #1: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688266] em28xx #1: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688285] em28xx #1: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 17.688304] em28xx #1: i2c eeprom f0: 00 00 00 00 00 00 00 00 07 56 d9 35 01 ed 0b f8 [ 17.688324] em28xx #1: EEPROM ID= 0x9567eb1a, EEPROM hash = 0x0fd77740 [ 17.688328] em28xx #1: EEPROM info: [ 17.688331] em28xx #1: AC97 audio (5 sample rates) [ 17.688334] em28xx #1: 500mA max power [ 17.688337] em28xx #1: Table at 0x06, strings=0x1e98, 0x2e6a, 0x0000 [ 17.691243] em28xx #1: Identified as Pinnacle PCTV USB 2 (card=3) [ 17.919731] saa7115 1-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #1) [ 18.380474] tda9887 1-0043: creating new instance [ 18.380505] tda9887 1-0043: tda988[5/6/7] found [ 18.387713] tuner 1-0043: Tuner 74 found with type(s) Radio TV. [ 18.393394] tuner 1-0063: Tuner -1 found with type(s) Radio TV. [ 18.394580] tuner-simple 1-0063: creating new instance [ 18.394614] tuner-simple 1-0063: type set to 37 (LG PAL (newer TAPC series)) [ 18.423184] em28xx #1: Config register raw data: 0x10 [ 18.437708] em28xx #1: AC97 vendor ID = 0xffffffff [ 18.444759] em28xx #1: AC97 features = 0x6a90 [ 18.444766] em28xx #1: Empia 202 AC97 audio processor detected [ 18.697684] em28xx #1: v4l2 driver version 0.1.3 [ 19.208320] em28xx #1: V4L2 video device registered as video1 [ 19.217065] usbcore: registered new interface driver em28xx [ 19.217081] em28xx driver loaded [ 19.512689] Adding 524284k swap on /dev/xvda1. Priority:-1 extents:1 across:524284k SS [ 19.519845] EXT4-fs (xvda2): re-mounted. Opts: (null) [ 19.653855] EXT4-fs (xvda2): re-mounted. Opts: barrier=1,errors=remount-ro [ 20.364396] EXT4-fs (xvdb1): mounted filesystem with ordered data mode. Opts: barrier=1,errors=remount-ro [ 27.694145] ehci_hcd 0000:04:00.5: iso resched full ffff88001938d000 (now 2818 max 6914) [ 27.694151] submit of urb 0 failed (error=-28) [ 28.106290] usbhid 6-1:1.0: disconnect by usbfs [ 28.106309] drivers/usb/core/file.c: removing 96 minor [ 31.771237] ehci_hcd 0000:04:00.5: iso resched full ffff88001abaf800 (now 2669 max 6765) [ 31.771243] submit of urb 0 failed (error=-28) [ 41.764131] ehci_hcd 0000:04:00.5: iso resched full ffff88001abad000 (now 697 max 4793) [ 41.764138] submit of urb 0 failed (error=-28) [ 51.773188] ehci_hcd 0000:04:00.5: iso resched full ffff88001abaf800 (now 2951 max 7047) [ 51.773194] submit of urb 0 failed (error=-28) [ 61.768234] ehci_hcd 0000:04:00.5: iso resched full ffff880013d4a000 (now 996 max 5092) [ 61.768241] submit of urb 0 failed (error=-28) [ 71.769031] ehci_hcd 0000:04:00.5: iso resched full ffff880013d4a800 (now 3183 max 7279) [ 71.769038] submit of urb 0 failed (error=-28) [ 81.767280] ehci_hcd 0000:04:00.5: iso resched full ffff8800139de000 (now 1253 max 5349) [ 81.767287] submit of urb 0 failed (error=-28) [ 91.763237] ehci_hcd 0000:04:00.5: iso resched full ffff8800139de800 (now 3402 max 7498) [ 91.763243] submit of urb 0 failed (error=-28) [ 101.769234] ehci_hcd 0000:04:00.5: iso resched full ffff88001368e000 (now 1535 max 5631) [ 101.769241] submit of urb 0 failed (error=-28) [ 111.767237] ehci_hcd 0000:04:00.5: iso resched full ffff88001368e800 (now 3700 max 7796) [ 111.767243] submit of urb 0 failed (error=-28) [ 121.762237] ehci_hcd 0000:04:00.5: iso resched full ffff88001334f800 (now 1745 max 5841) [ 121.762244] submit of urb 0 failed (error=-28) [ 131.767295] ehci_hcd 0000:04:00.5: iso resched full ffff880012dce000 (now 3966 max 8062) [ 131.767301] submit of urb 0 failed (error=-28) [ 141.768129] ehci_hcd 0000:04:00.5: iso resched full ffff880012dce800 (now 2058 max 6154) [ 141.768136] submit of urb 0 failed (error=-28) [ 151.772234] ehci_hcd 0000:04:00.5: iso resched full ffff880012742000 (now 176 max 4272) [ 151.772241] submit of urb 0 failed (error=-28) [ 161.767234] ehci_hcd 0000:04:00.5: iso resched full ffff880012743000 (now 2317 max 6413) [ 161.767241] submit of urb 0 failed (error=-28) [ 171.768237] ehci_hcd 0000:04:00.5: iso resched full ffff88001234a000 (now 410 max 4506) [ 171.768243] submit of urb 0 failed (error=-28) [ 181.768236] ehci_hcd 0000:04:00.5: iso resched full ffff88001234b000 (now 2591 max 6687) [ 181.768243] submit of urb 0 failed (error=-28) [ 191.769234] ehci_hcd 0000:04:00.5: iso resched full ffff880011ffe000 (now 683 max 4779) [ 191.769241] submit of urb 0 failed (error=-28)