| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1328357771-31644-8-git-send-email-aneesh@ti.com>
Date: Sat, 4 Feb 2012 17:46:10 +0530
From: Aneesh V <aneesh@...com>
To: linux-omap@...r.kernel.org
Cc: linux-kernel@...r.kernel.org, akpm@...ux-foundation.org,
Aneesh V <aneesh@...com>
Subject: [RFC PATCH 7/8] misc: emif: add one-time settings
Add settings that are not dependent on frequency
or any other transient parameters
Signed-off-by: Aneesh V <aneesh@...com>
---
drivers/misc/emif.c | 147 +++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 147 insertions(+), 0 deletions(-)
diff --git a/drivers/misc/emif.c b/drivers/misc/emif.c
index 5c2b0ae..9d24cc7 100644
--- a/drivers/misc/emif.c
+++ b/drivers/misc/emif.c
@@ -74,6 +74,24 @@ static void set_ddr_clk_period(u32 freq)
}
/*
+ * Get bus width used by EMIF. Note that this may be different from the
+ * bus width of the DDR devices used. For instance two 16-bit DDR devices
+ * may be connected to a given CS of EMIF. In this case bus width as far
+ * as EMIF is concerned is 32, where as the DDR bus width is 16 bits.
+ */
+static u32 get_emif_bus_width(struct emif_data *emif)
+{
+ u32 width;
+ void __iomem *base = emif->base;
+
+ width = (readl(base + EMIF_SDRAM_CONFIG) & NARROW_MODE_MASK)
+ >> NARROW_MODE_SHIFT;
+ width = width == 0 ? 32 : 16;
+
+ return width;
+}
+
+/*
* Get the CL from SDRAM_CONFIG register
*/
static u32 get_cl(struct emif_data *emif)
@@ -331,6 +349,70 @@ static u32 get_sdram_tim_3_shdw(const struct lpddr2_timings *timings,
return tim3;
}
+static u32 get_zq_config_reg(const struct lpddr2_addressing *addressing,
+ bool cs1_used, bool cal_resistors_per_cs)
+{
+ u32 zq = 0, val = 0;
+
+ val = EMIF_ZQCS_INTERVAL_US * 1000 / addressing->tREFI_ns;
+ zq |= val << ZQ_REFINTERVAL_SHIFT;
+
+ val = DIV_ROUND_UP(T_ZQCL_DEFAULT_NS, T_ZQCS_DEFAULT_NS) - 1;
+ zq |= val << ZQ_ZQCL_MULT_SHIFT;
+
+ val = DIV_ROUND_UP(T_ZQINIT_DEFAULT_NS, T_ZQCL_DEFAULT_NS) - 1;
+ zq |= val << ZQ_ZQINIT_MULT_SHIFT;
+
+ zq |= ZQ_SFEXITEN_ENABLE << ZQ_SFEXITEN_SHIFT;
+
+ if (cal_resistors_per_cs)
+ zq |= ZQ_DUALCALEN_ENABLE << ZQ_DUALCALEN_SHIFT;
+ else
+ zq |= ZQ_DUALCALEN_DISABLE << ZQ_DUALCALEN_SHIFT;
+
+ zq |= ZQ_CS0EN_MASK; /* CS0 is used for sure */
+
+ val = cs1_used ? 1 : 0;
+ zq |= val << ZQ_CS1EN_SHIFT;
+
+ return zq;
+}
+
+static u32 get_temp_alert_config(const struct lpddr2_addressing *addressing,
+ const struct emif_custom_configs *custom_configs, bool cs1_used,
+ u32 sdram_io_width, u32 emif_bus_width)
+{
+ u32 alert = 0, interval, devcnt;
+
+ if (custom_configs && (custom_configs->mask &
+ EMIF_CUSTOM_CONFIG_TEMP_ALERT_POLL_INTERVAL))
+ interval = custom_configs->temp_alert_poll_interval_ms;
+ else
+ interval = TEMP_ALERT_POLL_INTERVAL_DEFAULT_MS;
+
+ interval *= 1000000; /* Convert to ns */
+ interval /= addressing->tREFI_ns; /* Convert to refresh cycles */
+ alert |= (interval << TA_REFINTERVAL_SHIFT);
+
+ /*
+ * sdram_io_width is in 'log2(x) - 1' form. Convert emif_bus_width
+ * also to this form and subtract to get TA_DEVCNT, which is
+ * in log2(x) form.
+ */
+ emif_bus_width = __fls(emif_bus_width) - 1;
+ devcnt = emif_bus_width - sdram_io_width;
+ alert |= devcnt << TA_DEVCNT_SHIFT;
+
+ /* DEVWDT is in 'log2(x) - 3' form */
+ alert |= (sdram_io_width - 2) << TA_DEVWDT_SHIFT;
+
+ alert |= 1 << TA_SFEXITEN_SHIFT;
+ alert |= 1 << TA_CS0EN_SHIFT;
+ alert |= (cs1_used ? 1 : 0) << TA_CS1EN_SHIFT;
+
+ return alert;
+}
+
static u32 get_read_idle_ctrl_shdw(u8 volt_ramp)
{
u32 idle = 0, val = 0;
@@ -771,6 +853,70 @@ static int __init setup_interrupts(struct emif_data *emif)
}
+static void __init emif_onetime_settings(struct emif_data *emif)
+{
+ u32 pwr_mgmt_ctrl, zq, temp_alert_cfg;
+ void __iomem *base = emif->base;
+ const struct lpddr2_addressing *addressing;
+ const struct ddr_device_info *device_info;
+
+ device_info = emif->plat_data->device_info;
+ addressing = get_addressing_table(device_info);
+
+ /*
+ * Init power management settings
+ * We don't know the frequency yet. Use a high frequency
+ * value for a conservative timeout setting
+ */
+ pwr_mgmt_ctrl = get_pwr_mgmt_ctrl(1000000000, emif,
+ emif->plat_data->ip_rev);
+ writel(pwr_mgmt_ctrl, base + EMIF_POWER_MANAGEMENT_CONTROL);
+
+ /* Init ZQ calibration settings */
+ zq = get_zq_config_reg(addressing, device_info->cs1_used,
+ device_info->cal_resistors_per_cs);
+ writel(zq, base + EMIF_SDRAM_OUTPUT_IMPEDANCE_CALIBRATION_CONFIG);
+
+ /* Check temperature level temperature level*/
+ get_temperature_level(emif);
+ if (emif->temperature_level == SDRAM_TEMP_VERY_HIGH_SHUTDOWN)
+ dev_emerg(emif->dev, "SDRAM temperature exceeds operating limit.. Needs shut down!!!\n");
+
+ /* Init temperature polling */
+ temp_alert_cfg = get_temp_alert_config(addressing,
+ emif->plat_data->custom_configs, device_info->cs1_used,
+ device_info->io_width, get_emif_bus_width(emif));
+ writel(temp_alert_cfg, base + EMIF_TEMPERATURE_ALERT_CONFIG);
+
+ /*
+ * Program external PHY control registers that are not frequency
+ * dependent
+ */
+ if (emif->plat_data->phy_type != EMIF_PHY_TYPE_INTELLIPHY)
+ return;
+ writel(EMIF_EXT_PHY_CTRL_1_VAL, base + EMIF_EXT_PHY_CTRL_1_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_5_VAL, base + EMIF_EXT_PHY_CTRL_5_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_6_VAL, base + EMIF_EXT_PHY_CTRL_6_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_7_VAL, base + EMIF_EXT_PHY_CTRL_7_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_8_VAL, base + EMIF_EXT_PHY_CTRL_8_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_9_VAL, base + EMIF_EXT_PHY_CTRL_9_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_10_VAL, base + EMIF_EXT_PHY_CTRL_10_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_11_VAL, base + EMIF_EXT_PHY_CTRL_11_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_12_VAL, base + EMIF_EXT_PHY_CTRL_12_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_13_VAL, base + EMIF_EXT_PHY_CTRL_13_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_14_VAL, base + EMIF_EXT_PHY_CTRL_14_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_15_VAL, base + EMIF_EXT_PHY_CTRL_15_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_16_VAL, base + EMIF_EXT_PHY_CTRL_16_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_17_VAL, base + EMIF_EXT_PHY_CTRL_17_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_18_VAL, base + EMIF_EXT_PHY_CTRL_18_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_19_VAL, base + EMIF_EXT_PHY_CTRL_19_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_20_VAL, base + EMIF_EXT_PHY_CTRL_20_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_21_VAL, base + EMIF_EXT_PHY_CTRL_21_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_22_VAL, base + EMIF_EXT_PHY_CTRL_22_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_23_VAL, base + EMIF_EXT_PHY_CTRL_23_SHDW);
+ writel(EMIF_EXT_PHY_CTRL_24_VAL, base + EMIF_EXT_PHY_CTRL_24_SHDW);
+}
+
static void __exit cleanup_emif(struct emif_data *emif)
{
if (emif) {
@@ -967,6 +1113,7 @@ static int __init emif_probe(struct platform_device *pdev)
emif->irq = res->start;
disable_and_clear_all_interrupts(emif);
+ emif_onetime_settings(emif);
dev_info(&pdev->dev, "Device configured with addr = %p and IRQ%d\n",
emif->base, emif->irq);
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists