| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1328641879-18884-2-git-send-email-jkrzyszt@tis.icnet.pl>
Date: Tue, 7 Feb 2012 20:11:17 +0100
From: Janusz Krzysztofik <jkrzyszt@....icnet.pl>
To: Tony Lindgren <tony@...mide.com>
Cc: Mark Brown <broonie@...nsource.wolfsonmicro.com>,
Liam Girdwood <lrg@...com>, linux-omap@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, alsa-devel@...a-project.org,
linux-kernel@...r.kernel.org,
Janusz Krzysztofik <jkrzyszt@....icnet.pl>
Subject: [RESUBMIT][PATCH v2 1/4] ARM: OMAP1: ams-delta: set up regulator over modem reset GPIO pin
The Amstrad Delta on-board latch2 bit named MODEM_NRESET, now available
as a GPIO pin AMS_DELTA_GPIO_PIN_NMODEM_RESET, is used to power up/down
(bring into/out of a reset state) two distinct on-board devices
simultaneously: the modem, and the voice codec. As a consequence, that
bit is, or can be, manipulated concurrently by two drivers, or their
platform provided hooks.
Instead of updating those drivers to use the gpiolib API as a new method
of controlling the MODEM_NRESET pin state, like it was done to other
drivers accessing latch2 pins, and still being vulnerable to potential
concurrency conflicts, or trying to solve that sharing issue with a
custom piece of code, set up a fixed regulator device on top of that
GPIO pin, with the intention of updating both drivers to manipulate that
regulator, not the GPIO pin directly.
Before the ASoC driver is updated and the modem platform data expanded
with a power management callback for switching its power, the
ams_delta_latch_write() function, which still provides the old API for
accessing latch2 functionality from not updated drivers, is modified to
toggle the regulator instead of the MODEM_NRESET GPIO pin. A helper
function provided for balancing the regulator enable/disable operations,
together with the consumer data needed for tracking the regulator state,
will be removed once the drivers are updated.
Depends on patch series "ARM: OMAP1: ams-delta: replace custom I/O with
GPIO".
Signed-off-by: Janusz Krzysztofik <jkrzyszt@....icnet.pl>
Cc: Tony Lindgren <tony@...mide.com>
---
Changes against initial version:
* rename consumer setup elements to match their final, modem only
related purpose,
* initialize the regulator pointer and mutex before first use, then
omit testing that pointer against NULL value.
arch/arm/mach-omap1/Kconfig | 2 +
arch/arm/mach-omap1/board-ams-delta.c | 104 +++++++++++++++++++++++++++++++--
2 files changed, 100 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index 5b1edba..4b6a774 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -157,6 +157,8 @@ config MACH_AMS_DELTA
select FIQ
select GPIO_GENERIC_PLATFORM
select LEDS_GPIO_REGISTER
+ select REGULATOR
+ select REGULATOR_FIXED_VOLTAGE
help
Support for the Amstrad E3 (codename Delta) videophone. Say Y here
if you have such a device.
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 87b1303..43dcbda 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -18,7 +18,11 @@
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/leds.h>
+#include <linux/mutex.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <linux/serial_8250.h>
#include <linux/export.h>
@@ -237,11 +241,6 @@ static struct gpio latch_gpios[] __initconst = {
.label = "scard_cmdvcc",
},
{
- .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "modem_nreset",
- },
- {
.gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC,
.flags = GPIOF_OUT_INIT_LOW,
.label = "modem_codec",
@@ -258,6 +257,71 @@ static struct gpio latch_gpios[] __initconst = {
},
};
+static struct regulator_consumer_supply modem_nreset_consumers[] __initconst = {
+ REGULATOR_SUPPLY("RESET#", "serial8250.1"),
+ REGULATOR_SUPPLY("POR", "cx20442-codec"),
+};
+
+static struct regulator_init_data modem_nreset_data __initconst = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ .boot_on = 1,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(modem_nreset_consumers),
+ .consumer_supplies = modem_nreset_consumers,
+};
+
+static struct fixed_voltage_config modem_nreset_config __initconst = {
+ .supply_name = "modem_nreset",
+ .microvolts = 3300000,
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
+ .startup_delay = 25000,
+ .enable_high = 1,
+ .enabled_at_boot = 1,
+ .init_data = &modem_nreset_data,
+};
+
+static struct platform_device modem_nreset_device = {
+ .name = "reg-fixed-voltage",
+ .id = -1,
+ .dev = {
+ .platform_data = &modem_nreset_config,
+ },
+};
+
+struct modem_private_data {
+ struct regulator *regulator;
+ struct {
+ struct mutex lock;
+ bool enabled;
+ } consumer;
+};
+
+static int regulator_toggle(struct modem_private_data *priv, bool enable)
+{
+ int err = 0;
+
+ mutex_lock(&priv->consumer.lock);
+ if (IS_ERR(priv->regulator)) {
+ err = PTR_ERR(priv->regulator);
+ } else if (enable) {
+ if (!priv->consumer.enabled) {
+ err = regulator_enable(priv->regulator);
+ priv->consumer.enabled = true;
+ }
+ } else {
+ if (priv->consumer.enabled) {
+ err = regulator_disable(priv->regulator);
+ priv->consumer.enabled = false;
+ }
+ }
+ mutex_unlock(&priv->consumer.lock);
+
+ return err;
+}
+
+static struct modem_private_data modem_priv;
+
void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
{
int bit = 0;
@@ -266,7 +330,10 @@ void ams_delta_latch_write(int base, int ngpio, u16 mask, u16 value)
for (; bit < ngpio; bit++, bitpos = bitpos << 1) {
if (!(mask & bitpos))
continue;
- gpio_set_value(base + bit, (value & bitpos) != 0);
+ else if (base + bit == AMS_DELTA_GPIO_PIN_MODEM_NRESET)
+ regulator_toggle(&modem_priv, (value & bitpos) != 0);
+ else
+ gpio_set_value(base + bit, (value & bitpos) != 0);
}
}
EXPORT_SYMBOL(ams_delta_latch_write);
@@ -496,6 +563,12 @@ static int __init late_init(void)
platform_add_devices(late_devices, ARRAY_SIZE(late_devices));
+ err = platform_device_register(&modem_nreset_device);
+ if (err) {
+ pr_err("Couldn't register the modem regulator device\n");
+ return err;
+ }
+
omap_cfg_reg(M14_1510_GPIO2);
ams_delta_modem_ports[0].irq =
gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
@@ -507,6 +580,10 @@ static int __init late_init(void)
}
gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
+ /* Initialize the modem_nreset regulator consumer before use */
+ mutex_init(&modem_priv.consumer.lock);
+ modem_priv.regulator = ERR_PTR(-ENODEV);
+
ams_delta_latch2_write(
AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);
@@ -514,8 +591,23 @@ static int __init late_init(void)
err = platform_device_register(&ams_delta_modem_device);
if (err)
goto gpio_free;
+
+ /*
+ * Once the modem device is registered, the modem_nreset
+ * regulator can be requested on behalf of that device.
+ * The regulator is used via ams_delta_latch_write()
+ * by the modem and ASoC drivers until updated.
+ */
+ modem_priv.regulator = regulator_get(&ams_delta_modem_device.dev,
+ "RESET#");
+ if (IS_ERR(modem_priv.regulator)) {
+ err = PTR_ERR(modem_priv.regulator);
+ goto unregister;
+ }
return 0;
+unregister:
+ platform_device_unregister(&ams_delta_modem_device);
gpio_free:
gpio_free(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
return err;
--
1.7.3.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists