| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20120220170620.GG5387@sortiz-mobl>
Date: Mon, 20 Feb 2012 18:06:20 +0100
From: Samuel Ortiz <sameo@...ux.intel.com>
To: Linus Walleij <linus.walleij@...ricsson.com>
Cc: linux-kernel@...r.kernel.org, Viresh Kumar <viresh.kumar@...com>,
Michel Jaouen <michel.jaouen@...ricsson.com>,
Chris Blair <chris.blair@...ricsson.com>,
Linus Walleij <linus.walleij@...aro.org>
Subject: Re: [PATCH] mfd/stmpe: Add support for no-interrupt config
Hi Linus,
On Tue, Jan 24, 2012 at 11:18:34AM +0100, Linus Walleij wrote:
> From: Chris Blair <chris.blair@...ricsson.com>
>
> Adds support for boards which have an STMPE device without the
> interrupt pin connected.
Applied, thanks.
Cheers,
Samuel.
> Cc: Viresh Kumar <viresh.kumar@...com>
> Signed-off-by: Chris Blair <chris.blair@...ricsson.com>
> Tested-by: Michel Jaouen <michel.jaouen@...ricsson.com>
> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@...ricsson.com>
> Signed-off-by: Linus Walleij <linus.walleij@...aro.org>
> ---
> drivers/mfd/stmpe.c | 72 +++++++++++++++++++++++++--------------------
> include/linux/mfd/stmpe.h | 2 +
> 2 files changed, 42 insertions(+), 32 deletions(-)
>
> diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
> index e07947e..7c98e61 100644
> --- a/drivers/mfd/stmpe.c
> +++ b/drivers/mfd/stmpe.c
> @@ -864,7 +864,7 @@ static int __devinit stmpe_chip_init(struct stmpe *stmpe)
> unsigned int irq_trigger = stmpe->pdata->irq_trigger;
> int autosleep_timeout = stmpe->pdata->autosleep_timeout;
> struct stmpe_variant_info *variant = stmpe->variant;
> - u8 icr;
> + u8 icr = 0;
> unsigned int id;
> u8 data[2];
> int ret;
> @@ -887,31 +887,33 @@ static int __devinit stmpe_chip_init(struct stmpe *stmpe)
> if (ret)
> return ret;
>
> - if (id == STMPE801_ID)
> - icr = STMPE801_REG_SYS_CTRL_INT_EN;
> - else
> - icr = STMPE_ICR_LSB_GIM;
> -
> - /* STMPE801 doesn't support Edge interrupts */
> - if (id != STMPE801_ID) {
> - if (irq_trigger == IRQF_TRIGGER_FALLING ||
> - irq_trigger == IRQF_TRIGGER_RISING)
> - icr |= STMPE_ICR_LSB_EDGE;
> - }
> -
> - if (irq_trigger == IRQF_TRIGGER_RISING ||
> - irq_trigger == IRQF_TRIGGER_HIGH) {
> + if (!stmpe->pdata->no_irq) {
> if (id == STMPE801_ID)
> - icr |= STMPE801_REG_SYS_CTRL_INT_HI;
> + icr = STMPE801_REG_SYS_CTRL_INT_EN;
> else
> - icr |= STMPE_ICR_LSB_HIGH;
> - }
> + icr = STMPE_ICR_LSB_GIM;
>
> - if (stmpe->pdata->irq_invert_polarity) {
> - if (id == STMPE801_ID)
> - icr ^= STMPE801_REG_SYS_CTRL_INT_HI;
> - else
> - icr ^= STMPE_ICR_LSB_HIGH;
> + /* STMPE801 doesn't support Edge interrupts */
> + if (id != STMPE801_ID) {
> + if (irq_trigger == IRQF_TRIGGER_FALLING ||
> + irq_trigger == IRQF_TRIGGER_RISING)
> + icr |= STMPE_ICR_LSB_EDGE;
> + }
> +
> + if (irq_trigger == IRQF_TRIGGER_RISING ||
> + irq_trigger == IRQF_TRIGGER_HIGH) {
> + if (id == STMPE801_ID)
> + icr |= STMPE801_REG_SYS_CTRL_INT_HI;
> + else
> + icr |= STMPE_ICR_LSB_HIGH;
> + }
> +
> + if (stmpe->pdata->irq_invert_polarity) {
> + if (id == STMPE801_ID)
> + icr ^= STMPE801_REG_SYS_CTRL_INT_HI;
> + else
> + icr ^= STMPE_ICR_LSB_HIGH;
> + }
> }
>
> if (stmpe->pdata->autosleep) {
> @@ -988,7 +990,7 @@ int __devinit stmpe_probe(struct stmpe_client_info *ci, int partnum)
> if (ci->init)
> ci->init(stmpe);
>
> - if (pdata->irq_over_gpio) {
> + if (!pdata->no_irq && pdata->irq_over_gpio) {
> ret = gpio_request_one(pdata->irq_gpio, GPIOF_DIR_IN, "stmpe");
> if (ret) {
> dev_err(stmpe->dev, "failed to request IRQ GPIO: %d\n",
> @@ -1005,15 +1007,21 @@ int __devinit stmpe_probe(struct stmpe_client_info *ci, int partnum)
> if (ret)
> goto free_gpio;
>
> - ret = stmpe_irq_init(stmpe);
> - if (ret)
> - goto free_gpio;
> + if (pdata->no_irq) {
> + dev_info(stmpe->dev,
> + "board config says IRQs are not supported\n");
> + } else {
> + ret = stmpe_irq_init(stmpe);
> + if (ret)
> + goto free_gpio;
>
> - ret = request_threaded_irq(stmpe->irq, NULL, stmpe_irq,
> - pdata->irq_trigger | IRQF_ONESHOT, "stmpe", stmpe);
> - if (ret) {
> - dev_err(stmpe->dev, "failed to request IRQ: %d\n", ret);
> - goto out_removeirq;
> + ret = request_threaded_irq(stmpe->irq, NULL, stmpe_irq,
> + pdata->irq_trigger | IRQF_ONESHOT,
> + "stmpe", stmpe);
> + if (ret) {
> + dev_err(stmpe->dev, "failed to request IRQ: %d\n", ret);
> + goto out_removeirq;
> + }
> }
>
> ret = stmpe_devices_init(stmpe);
> diff --git a/include/linux/mfd/stmpe.h b/include/linux/mfd/stmpe.h
> index ca1d7a3..c4b45fd 100644
> --- a/include/linux/mfd/stmpe.h
> +++ b/include/linux/mfd/stmpe.h
> @@ -188,6 +188,7 @@ struct stmpe_ts_platform_data {
> * @irq_invert_polarity: IRQ line is connected with reversed polarity
> * @autosleep: bool to enable/disable stmpe autosleep
> * @autosleep_timeout: inactivity timeout in milliseconds for autosleep
> + * @no_irq: IRQs are not supported on this board
> * @irq_base: base IRQ number. %STMPE_NR_IRQS irqs will be used, or
> * %STMPE_NR_INTERNAL_IRQS if the GPIO driver is not used.
> * @irq_over_gpio: true if gpio is used to get irq
> @@ -200,6 +201,7 @@ struct stmpe_ts_platform_data {
> struct stmpe_platform_data {
> int id;
> unsigned int blocks;
> + bool no_irq;
> int irq_base;
> unsigned int irq_trigger;
> bool irq_invert_polarity;
> --
> 1.7.8
>
--
Intel Open Source Technology Centre
http://oss.intel.com/
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists