| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <1332173578-27422-10-git-send-email-j-pihet@ti.com>
Date: Mon, 19 Mar 2012 17:12:58 +0100
From: jean.pihet@...oldbits.com
To: linux-omap@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
Kevin Hilman <khilman@...com>,
"Rafael J. Wysocki" <rjw@...k.pl>,
LKML <linux-kernel@...r.kernel.org>
Cc: Jean Pihet <j-pihet@...com>
Subject: [PATCH 9/9] ARM: OMAP: SmartReflex: Move smartreflex driver to drivers/
From: Jean Pihet <j-pihet@...com>
After a clean-up of the interfaces the OMAP IP driver and class
support code is now a generic driver.
Move it to drivers/power/avs/.
The build is controlled by the following Kconfig options:
. CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
. CONFIG_POWER_AVS_OMAP: AVS support on OMAP containing the version 1
or version 2 of the SmartReflex IP,
. CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@...com>
---
arch/arm/mach-omap2/Makefile | 3 +-
arch/arm/mach-omap2/smartreflex-class3.c | 61 --
arch/arm/mach-omap2/smartreflex.c | 1120 ------------------------------
arch/arm/mach-omap2/smartreflex.h | 238 -------
arch/arm/plat-omap/Kconfig | 19 +-
drivers/power/Kconfig | 2 +
drivers/power/Makefile | 2 +
drivers/power/avs/Kconfig | 12 +
drivers/power/avs/Makefile | 2 +
drivers/power/avs/smartreflex-class3.c | 61 ++
drivers/power/avs/smartreflex.c | 1118 +++++++++++++++++++++++++++++
drivers/power/avs/smartreflex.h | 238 +++++++
12 files changed, 1437 insertions(+), 1439 deletions(-)
delete mode 100644 arch/arm/mach-omap2/smartreflex-class3.c
delete mode 100644 arch/arm/mach-omap2/smartreflex.c
delete mode 100644 arch/arm/mach-omap2/smartreflex.h
create mode 100644 drivers/power/avs/Kconfig
create mode 100644 drivers/power/avs/Makefile
create mode 100644 drivers/power/avs/smartreflex-class3.c
create mode 100644 drivers/power/avs/smartreflex.c
create mode 100644 drivers/power/avs/smartreflex.h
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 30666fd..bb23056 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -69,8 +69,7 @@ obj-$(CONFIG_ARCH_OMAP4) += pm44xx.o omap-mpuss-lowpower.o \
cpuidle44xx.o
obj-$(CONFIG_PM_DEBUG) += pm-debug.o
-obj-$(CONFIG_POWER_AVS_OMAP) += sr_device.o smartreflex.o
-obj-$(CONFIG_POWER_AVS_OMAP_CLASS3) += smartreflex-class3.o
+obj-$(CONFIG_POWER_AVS_OMAP) += sr_device.o
AFLAGS_sleep24xx.o :=-Wa,-march=armv6
AFLAGS_sleep34xx.o :=-Wa,-march=armv7-a$(plus_sec)
diff --git a/arch/arm/mach-omap2/smartreflex-class3.c b/arch/arm/mach-omap2/smartreflex-class3.c
deleted file mode 100644
index f63c950..0000000
--- a/arch/arm/mach-omap2/smartreflex-class3.c
+++ /dev/null
@@ -1,61 +0,0 @@
-/*
- * Smart reflex Class 3 specific implementations
- *
- * Author: Thara Gopinath <thara@...com>
- *
- * Copyright (C) 2010 Texas Instruments, Inc.
- * Thara Gopinath <thara@...com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include "smartreflex.h"
-#include "voltage.h"
-
-static int sr_class3_enable(struct omap_sr *sr)
-{
- unsigned long volt = voltdm_get_voltage(sr->voltdm);
-
- if (!volt) {
- pr_warning("%s: Curr voltage unknown. Cannot enable %s\n",
- __func__, sr->name);
- return -ENODATA;
- }
-
- omap_vp_enable(sr->voltdm);
- return sr_enable(sr->voltdm, volt);
-}
-
-static int sr_class3_disable(struct omap_sr *sr, int is_volt_reset)
-{
- sr_disable_errgen(sr->voltdm);
- omap_vp_disable(sr->voltdm);
- sr_disable(sr->voltdm);
- if (is_volt_reset)
- voltdm_reset(sr->voltdm);
-
- return 0;
-}
-
-static int sr_class3_configure(struct omap_sr *sr)
-{
- return sr_configure_errgen(sr->voltdm);
-}
-
-/* SR class3 structure */
-static struct omap_sr_class_data class3_data = {
- .enable = sr_class3_enable,
- .disable = sr_class3_disable,
- .configure = sr_class3_configure,
- .class_type = SR_CLASS3,
-};
-
-/* Smartreflex Class3 init API to be called from board file */
-static int __init sr_class3_init(void)
-{
- pr_info("SmartReflex Class3 initialized\n");
- return sr_register_class(&class3_data);
-}
-late_initcall(sr_class3_init);
diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c
deleted file mode 100644
index 71f70ca..0000000
--- a/arch/arm/mach-omap2/smartreflex.c
+++ /dev/null
@@ -1,1120 +0,0 @@
-/*
- * OMAP SmartReflex Voltage Control
- *
- * Author: Thara Gopinath <thara@...com>
- *
- * Copyright (C) 2010 Texas Instruments, Inc.
- * Thara Gopinath <thara@...com>
- *
- * Copyright (C) 2008 Nokia Corporation
- * Kalle Jokiniemi
- *
- * Copyright (C) 2007 Texas Instruments, Inc.
- * Lesly A M <x0080970@...com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/debugfs.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/pm_runtime.h>
-#include <linux/power/smartreflex.h>
-
-#include "common.h"
-#include "pm.h"
-#include "smartreflex.h"
-
-#define SMARTREFLEX_NAME_LEN 16
-#define NVALUE_NAME_LEN 40
-#define SR_DISABLE_TIMEOUT 200
-
-/* sr_list contains all the instances of smartreflex module */
-static LIST_HEAD(sr_list);
-
-static struct omap_sr_class_data *sr_class;
-static struct omap_sr_pmic_data *sr_pmic_data;
-static struct dentry *sr_dbg_dir;
-
-static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32 value)
-{
- __raw_writel(value, (sr->base + offset));
-}
-
-static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
- u32 value)
-{
- u32 reg_val;
-
- /*
- * Smartreflex error config register is special as it contains
- * certain status bits which if written a 1 into means a clear
- * of those bits. So in order to make sure no accidental write of
- * 1 happens to those status bits, do a clear of them in the read
- * value. This mean this API doesn't rewrite values in these bits
- * if they are currently set, but does allow the caller to write
- * those bits.
- */
- if (sr->ip_type == SR_TYPE_V1 && offset == ERRCONFIG_V1)
- mask |= ERRCONFIG_STATUS_V1_MASK;
- else if (sr->ip_type == SR_TYPE_V2 && offset == ERRCONFIG_V2)
- mask |= ERRCONFIG_VPBOUNDINTST_V2;
-
- reg_val = __raw_readl(sr->base + offset);
- reg_val &= ~mask;
-
- value &= mask;
-
- reg_val |= value;
-
- __raw_writel(reg_val, (sr->base + offset));
-}
-
-static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)
-{
- return __raw_readl(sr->base + offset);
-}
-
-static struct omap_sr *_sr_lookup(struct voltagedomain *voltdm)
-{
- struct omap_sr *sr_info;
-
- if (!voltdm) {
- pr_err("%s: Null voltage domain passed!\n", __func__);
- return ERR_PTR(-EINVAL);
- }
-
- list_for_each_entry(sr_info, &sr_list, node) {
- if (voltdm == sr_info->voltdm)
- return sr_info;
- }
-
- return ERR_PTR(-ENODATA);
-}
-
-static irqreturn_t sr_interrupt(int irq, void *data)
-{
- struct omap_sr *sr_info = data;
- u32 status = 0;
-
- switch (sr_info->ip_type) {
- case SR_TYPE_V1:
- /* Read the status bits */
- status = sr_read_reg(sr_info, ERRCONFIG_V1);
-
- /* Clear them by writing back */
- sr_write_reg(sr_info, ERRCONFIG_V1, status);
- break;
- case SR_TYPE_V2:
- /* Read the status bits */
- status = sr_read_reg(sr_info, IRQSTATUS);
-
- /* Clear them by writing back */
- sr_write_reg(sr_info, IRQSTATUS, status);
- break;
- default:
- dev_err(&sr_info->pdev->dev, "UNKNOWN IP type %d\n",
- sr_info->ip_type);
- return IRQ_NONE;
- }
-
- if (sr_class->notify)
- sr_class->notify(sr_info, status);
-
- return IRQ_HANDLED;
-}
-
-static void sr_set_clk_length(struct omap_sr *sr)
-{
- struct clk *sys_ck;
- u32 sys_clk_speed;
-
- if (cpu_is_omap34xx())
- sys_ck = clk_get(NULL, "sys_ck");
- else
- sys_ck = clk_get(NULL, "sys_clkin_ck");
-
- if (IS_ERR(sys_ck)) {
- dev_err(&sr->pdev->dev, "%s: unable to get sys clk\n",
- __func__);
- return;
- }
-
- sys_clk_speed = clk_get_rate(sys_ck);
- clk_put(sys_ck);
-
- switch (sys_clk_speed) {
- case 12000000:
- sr->clk_length = SRCLKLENGTH_12MHZ_SYSCLK;
- break;
- case 13000000:
- sr->clk_length = SRCLKLENGTH_13MHZ_SYSCLK;
- break;
- case 19200000:
- sr->clk_length = SRCLKLENGTH_19MHZ_SYSCLK;
- break;
- case 26000000:
- sr->clk_length = SRCLKLENGTH_26MHZ_SYSCLK;
- break;
- case 38400000:
- sr->clk_length = SRCLKLENGTH_38MHZ_SYSCLK;
- break;
- default:
- dev_err(&sr->pdev->dev, "%s: Invalid sysclk value: %d\n",
- __func__, sys_clk_speed);
- break;
- }
-}
-
-static void sr_set_regfields(struct omap_sr *sr)
-{
- /*
- * For time being these values are defined in smartreflex.h
- * and populated during init. May be they can be moved to board
- * file or pmic specific data structure. In that case these structure
- * fields will have to be populated using the pdata or pmic structure.
- */
- if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
- sr->err_weight = OMAP3430_SR_ERRWEIGHT;
- sr->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT;
- sr->accum_data = OMAP3430_SR_ACCUMDATA;
- if (!(strcmp(sr->name, "sr_mpu_iva"))) {
- sr->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT;
- sr->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT;
- } else {
- sr->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT;
- sr->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT;
- }
- }
-}
-
-static void sr_start_vddautocomp(struct omap_sr *sr)
-{
- if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
- dev_warn(&sr->pdev->dev,
- "%s: smartreflex class driver not registered\n",
- __func__);
- return;
- }
-
- if (!sr_class->enable(sr))
- sr->autocomp_active = true;
-}
-
-static void sr_stop_vddautocomp(struct omap_sr *sr)
-{
- if (!sr_class || !(sr_class->disable)) {
- dev_warn(&sr->pdev->dev,
- "%s: smartreflex class driver not registered\n",
- __func__);
- return;
- }
-
- if (sr->autocomp_active) {
- sr_class->disable(sr, 1);
- sr->autocomp_active = false;
- }
-}
-
-/*
- * This function handles the intializations which have to be done
- * only when both sr device and class driver regiter has
- * completed. This will be attempted to be called from both sr class
- * driver register and sr device intializtion API's. Only one call
- * will ultimately succeed.
- *
- * Currently this function registers interrupt handler for a particular SR
- * if smartreflex class driver is already registered and has
- * requested for interrupts and the SR interrupt line in present.
- */
-static int sr_late_init(struct omap_sr *sr_info)
-{
- struct omap_sr_data *pdata = sr_info->pdev->dev.platform_data;
- struct resource *mem;
- int ret = 0;
-
- if (sr_class->notify && sr_class->notify_flags && sr_info->irq) {
- ret = request_irq(sr_info->irq, sr_interrupt,
- 0, sr_info->name, sr_info);
- if (ret)
- goto error;
- disable_irq(sr_info->irq);
- }
-
- if (pdata && pdata->enable_on_init)
- sr_start_vddautocomp(sr_info);
-
- return ret;
-
-error:
- iounmap(sr_info->base);
- mem = platform_get_resource(sr_info->pdev, IORESOURCE_MEM, 0);
- release_mem_region(mem->start, resource_size(mem));
- list_del(&sr_info->node);
- dev_err(&sr_info->pdev->dev, "%s: ERROR in registering"
- "interrupt handler. Smartreflex will"
- "not function as desired\n", __func__);
- kfree(sr_info);
-
- return ret;
-}
-
-static void sr_v1_disable(struct omap_sr *sr)
-{
- int timeout = 0;
- int errconf_val = ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
- ERRCONFIG_MCUBOUNDINTST;
-
- /* Enable MCUDisableAcknowledge interrupt */
- sr_modify_reg(sr, ERRCONFIG_V1,
- ERRCONFIG_MCUDISACKINTEN, ERRCONFIG_MCUDISACKINTEN);
-
- /* SRCONFIG - disable SR */
- sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
-
- /* Disable all other SR interrupts and clear the status as needed */
- if (sr_read_reg(sr, ERRCONFIG_V1) & ERRCONFIG_VPBOUNDINTST_V1)
- errconf_val |= ERRCONFIG_VPBOUNDINTST_V1;
- sr_modify_reg(sr, ERRCONFIG_V1,
- (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
- ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN_V1),
- errconf_val);
-
- /*
- * Wait for SR to be disabled.
- * wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us.
- */
- sr_test_cond_timeout((sr_read_reg(sr, ERRCONFIG_V1) &
- ERRCONFIG_MCUDISACKINTST), SR_DISABLE_TIMEOUT,
- timeout);
-
- if (timeout >= SR_DISABLE_TIMEOUT)
- dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
- __func__);
-
- /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
- sr_modify_reg(sr, ERRCONFIG_V1, ERRCONFIG_MCUDISACKINTEN,
- ERRCONFIG_MCUDISACKINTST);
-}
-
-static void sr_v2_disable(struct omap_sr *sr)
-{
- int timeout = 0;
-
- /* Enable MCUDisableAcknowledge interrupt */
- sr_write_reg(sr, IRQENABLE_SET, IRQENABLE_MCUDISABLEACKINT);
-
- /* SRCONFIG - disable SR */
- sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
-
- /*
- * Disable all other SR interrupts and clear the status
- * write to status register ONLY on need basis - only if status
- * is set.
- */
- if (sr_read_reg(sr, ERRCONFIG_V2) & ERRCONFIG_VPBOUNDINTST_V2)
- sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
- ERRCONFIG_VPBOUNDINTST_V2);
- else
- sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
- 0x0);
- sr_write_reg(sr, IRQENABLE_CLR, (IRQENABLE_MCUACCUMINT |
- IRQENABLE_MCUVALIDINT |
- IRQENABLE_MCUBOUNDSINT));
- sr_write_reg(sr, IRQSTATUS, (IRQSTATUS_MCUACCUMINT |
- IRQSTATUS_MCVALIDINT |
- IRQSTATUS_MCBOUNDSINT));
-
- /*
- * Wait for SR to be disabled.
- * wait until IRQSTATUS.MCUDISACKINTST = 1. Typical latency is 1us.
- */
- sr_test_cond_timeout((sr_read_reg(sr, IRQSTATUS) &
- IRQSTATUS_MCUDISABLEACKINT), SR_DISABLE_TIMEOUT,
- timeout);
-
- if (timeout >= SR_DISABLE_TIMEOUT)
- dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
- __func__);
-
- /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
- sr_write_reg(sr, IRQENABLE_CLR, IRQENABLE_MCUDISABLEACKINT);
- sr_write_reg(sr, IRQSTATUS, IRQSTATUS_MCUDISABLEACKINT);
-}
-
-static struct omap_sr_nvalue_table *sr_retrieve_nvalue_row(
- struct omap_sr *sr,
- unsigned long volt_nominal)
-{
- int i;
-
- if (!sr->nvalue_table) {
- dev_warn(&sr->pdev->dev, "%s: Missing ntarget value table\n",
- __func__);
- return NULL;
- }
-
- for (i = 0; i < sr->nvalue_count; i++) {
- if (sr->nvalue_table[i].volt_nominal == volt_nominal)
- return &sr->nvalue_table[i];
- }
-
- return NULL;
-}
-
-/* Public Functions */
-
-/**
- * sr_configure_errgen() - Configures the smrtreflex to perform AVS using the
- * error generator module.
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the smartreflex class driver to
- * configure the error generator module inside the smartreflex module.
- * SR settings if using the ERROR module inside Smartreflex.
- * SR CLASS 3 by default uses only the ERROR module where as
- * SR CLASS 2 can choose between ERROR module and MINMAXAVG
- * module. Returns 0 on success and error value in case of failure.
- */
-int sr_configure_errgen(struct voltagedomain *voltdm)
-{
- u32 sr_config, sr_errconfig, errconfig_offs;
- u32 vpboundint_en, vpboundint_st;
- u32 senp_en = 0, senn_en = 0;
- u8 senp_shift, senn_shift;
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return PTR_ERR(sr);
- }
-
- if (!sr->clk_length)
- sr_set_clk_length(sr);
-
- senp_en = sr->senp_mod;
- senn_en = sr->senn_mod;
-
- sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
- SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN;
-
- switch (sr->ip_type) {
- case SR_TYPE_V1:
- sr_config |= SRCONFIG_DELAYCTRL;
- senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
- senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
- errconfig_offs = ERRCONFIG_V1;
- vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
- vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
- break;
- case SR_TYPE_V2:
- senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
- senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
- errconfig_offs = ERRCONFIG_V2;
- vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
- vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
- break;
- default:
- dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
- "module without specifying the ip\n", __func__);
- return -EINVAL;
- }
-
- sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
- sr_write_reg(sr, SRCONFIG, sr_config);
- sr_errconfig = (sr->err_weight << ERRCONFIG_ERRWEIGHT_SHIFT) |
- (sr->err_maxlimit << ERRCONFIG_ERRMAXLIMIT_SHIFT) |
- (sr->err_minlimit << ERRCONFIG_ERRMINLIMIT_SHIFT);
- sr_modify_reg(sr, errconfig_offs, (SR_ERRWEIGHT_MASK |
- SR_ERRMAXLIMIT_MASK | SR_ERRMINLIMIT_MASK),
- sr_errconfig);
-
- /* Enabling the interrupts if the ERROR module is used */
- sr_modify_reg(sr, errconfig_offs, (vpboundint_en | vpboundint_st),
- vpboundint_en);
-
- return 0;
-}
-
-/**
- * sr_disable_errgen() - Disables SmartReflex AVS module's errgen component
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the smartreflex class driver to
- * disable the error generator module inside the smartreflex module.
- *
- * Returns 0 on success and error value in case of failure.
- */
-int sr_disable_errgen(struct voltagedomain *voltdm)
-{
- u32 errconfig_offs;
- u32 vpboundint_en, vpboundint_st;
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return PTR_ERR(sr);
- }
-
- switch (sr->ip_type) {
- case SR_TYPE_V1:
- errconfig_offs = ERRCONFIG_V1;
- vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
- vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
- break;
- case SR_TYPE_V2:
- errconfig_offs = ERRCONFIG_V2;
- vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
- vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
- break;
- default:
- dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
- "module without specifying the ip\n", __func__);
- return -EINVAL;
- }
-
- /* Disable the interrupts of ERROR module */
- sr_modify_reg(sr, errconfig_offs, vpboundint_en | vpboundint_st, 0);
-
- /* Disable the Sensor and errorgen */
- sr_modify_reg(sr, SRCONFIG, SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN, 0);
-
- return 0;
-}
-
-/**
- * sr_configure_minmax() - Configures the smrtreflex to perform AVS using the
- * minmaxavg module.
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the smartreflex class driver to
- * configure the minmaxavg module inside the smartreflex module.
- * SR settings if using the ERROR module inside Smartreflex.
- * SR CLASS 3 by default uses only the ERROR module where as
- * SR CLASS 2 can choose between ERROR module and MINMAXAVG
- * module. Returns 0 on success and error value in case of failure.
- */
-int sr_configure_minmax(struct voltagedomain *voltdm)
-{
- u32 sr_config, sr_avgwt;
- u32 senp_en = 0, senn_en = 0;
- u8 senp_shift, senn_shift;
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return PTR_ERR(sr);
- }
-
- if (!sr->clk_length)
- sr_set_clk_length(sr);
-
- senp_en = sr->senp_mod;
- senn_en = sr->senn_mod;
-
- sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
- SRCONFIG_SENENABLE |
- (sr->accum_data << SRCONFIG_ACCUMDATA_SHIFT);
-
- switch (sr->ip_type) {
- case SR_TYPE_V1:
- sr_config |= SRCONFIG_DELAYCTRL;
- senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
- senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
- break;
- case SR_TYPE_V2:
- senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
- senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
- break;
- default:
- dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
- "module without specifying the ip\n", __func__);
- return -EINVAL;
- }
-
- sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
- sr_write_reg(sr, SRCONFIG, sr_config);
- sr_avgwt = (sr->senp_avgweight << AVGWEIGHT_SENPAVGWEIGHT_SHIFT) |
- (sr->senn_avgweight << AVGWEIGHT_SENNAVGWEIGHT_SHIFT);
- sr_write_reg(sr, AVGWEIGHT, sr_avgwt);
-
- /*
- * Enabling the interrupts if MINMAXAVG module is used.
- * TODO: check if all the interrupts are mandatory
- */
- switch (sr->ip_type) {
- case SR_TYPE_V1:
- sr_modify_reg(sr, ERRCONFIG_V1,
- (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
- ERRCONFIG_MCUBOUNDINTEN),
- (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUACCUMINTST |
- ERRCONFIG_MCUVALIDINTEN | ERRCONFIG_MCUVALIDINTST |
- ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST));
- break;
- case SR_TYPE_V2:
- sr_write_reg(sr, IRQSTATUS,
- IRQSTATUS_MCUACCUMINT | IRQSTATUS_MCVALIDINT |
- IRQSTATUS_MCBOUNDSINT | IRQSTATUS_MCUDISABLEACKINT);
- sr_write_reg(sr, IRQENABLE_SET,
- IRQENABLE_MCUACCUMINT | IRQENABLE_MCUVALIDINT |
- IRQENABLE_MCUBOUNDSINT | IRQENABLE_MCUDISABLEACKINT);
- break;
- default:
- dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
- "module without specifying the ip\n", __func__);
- return -EINVAL;
- }
-
- return 0;
-}
-
-/**
- * sr_enable() - Enables the smartreflex module.
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- * @volt: The voltage at which the Voltage domain associated with
- * the smartreflex module is operating at.
- * This is required only to program the correct Ntarget value.
- *
- * This API is to be called from the smartreflex class driver to
- * enable a smartreflex module. Returns 0 on success. Returns error
- * value if the voltage passed is wrong or if ntarget value is wrong.
- */
-int sr_enable(struct voltagedomain *voltdm, unsigned long volt)
-{
- struct omap_sr *sr = _sr_lookup(voltdm);
- struct omap_sr_nvalue_table *nvalue_row;
- int ret;
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return PTR_ERR(sr);
- }
-
- nvalue_row = sr_retrieve_nvalue_row(sr, volt);
- if (!nvalue_row) {
- dev_warn(&sr->pdev->dev, "%s: failure getting SR data for this voltage %ld\n",
- __func__, volt);
- return -ENODATA;
- }
-
-
- /* errminlimit is opp dependent and hence linked to voltage */
- sr->err_minlimit = nvalue_row->errminlimit;
-
- pm_runtime_get_sync(&sr->pdev->dev);
-
- /* Check if SR is already enabled. If yes do nothing */
- if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE)
- return 0;
-
- /* Configure SR */
- ret = sr_class->configure(sr);
- if (ret)
- return ret;
-
- sr_write_reg(sr, NVALUERECIPROCAL, nvalue_row->nvalue);
-
- /* SRCONFIG - enable SR */
- sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, SRCONFIG_SRENABLE);
- return 0;
-}
-
-/**
- * sr_disable() - Disables the smartreflex module.
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the smartreflex class driver to
- * disable a smartreflex module.
- */
-void sr_disable(struct voltagedomain *voltdm)
-{
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return;
- }
-
- /* Check if SR clocks are already disabled. If yes do nothing */
- if (pm_runtime_suspended(&sr->pdev->dev))
- return;
-
- /*
- * Disable SR if only it is indeed enabled. Else just
- * disable the clocks.
- */
- if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) {
- switch (sr->ip_type) {
- case SR_TYPE_V1:
- sr_v1_disable(sr);
- break;
- case SR_TYPE_V2:
- sr_v2_disable(sr);
- break;
- default:
- dev_err(&sr->pdev->dev, "UNKNOWN IP type %d\n",
- sr->ip_type);
- }
- }
-
- pm_runtime_put_sync_suspend(&sr->pdev->dev);
-}
-
-/**
- * sr_register_class() - API to register a smartreflex class parameters.
- * @class_data: The structure containing various sr class specific data.
- *
- * This API is to be called by the smartreflex class driver to register itself
- * with the smartreflex driver during init. Returns 0 on success else the
- * error value.
- */
-int sr_register_class(struct omap_sr_class_data *class_data)
-{
- struct omap_sr *sr_info;
-
- if (!class_data) {
- pr_warning("%s:, Smartreflex class data passed is NULL\n",
- __func__);
- return -EINVAL;
- }
-
- if (sr_class) {
- pr_warning("%s: Smartreflex class driver already registered\n",
- __func__);
- return -EBUSY;
- }
-
- sr_class = class_data;
-
- /*
- * Call into late init to do intializations that require
- * both sr driver and sr class driver to be initiallized.
- */
- list_for_each_entry(sr_info, &sr_list, node)
- sr_late_init(sr_info);
-
- return 0;
-}
-
-/**
- * omap_sr_enable() - API to enable SR clocks and to call into the
- * registered smartreflex class enable API.
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the kernel in order to enable
- * a particular smartreflex module. This API will do the initial
- * configurations to turn on the smartreflex module and in turn call
- * into the registered smartreflex class enable API.
- */
-void omap_sr_enable(struct voltagedomain *voltdm)
-{
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return;
- }
-
- if (!sr->autocomp_active)
- return;
-
- if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
- dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
- "registered\n", __func__);
- return;
- }
-
- sr_class->enable(sr);
-}
-
-/**
- * omap_sr_disable() - API to disable SR without resetting the voltage
- * processor voltage
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the kernel in order to disable
- * a particular smartreflex module. This API will in turn call
- * into the registered smartreflex class disable API. This API will tell
- * the smartreflex class disable not to reset the VP voltage after
- * disabling smartreflex.
- */
-void omap_sr_disable(struct voltagedomain *voltdm)
-{
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return;
- }
-
- if (!sr->autocomp_active)
- return;
-
- if (!sr_class || !(sr_class->disable)) {
- dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
- "registered\n", __func__);
- return;
- }
-
- sr_class->disable(sr, 0);
-}
-
-/**
- * omap_sr_disable_reset_volt() - API to disable SR and reset the
- * voltage processor voltage
- * @voltdm: VDD pointer to which the SR module to be configured belongs to.
- *
- * This API is to be called from the kernel in order to disable
- * a particular smartreflex module. This API will in turn call
- * into the registered smartreflex class disable API. This API will tell
- * the smartreflex class disable to reset the VP voltage after
- * disabling smartreflex.
- */
-void omap_sr_disable_reset_volt(struct voltagedomain *voltdm)
-{
- struct omap_sr *sr = _sr_lookup(voltdm);
-
- if (IS_ERR(sr)) {
- pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
- return;
- }
-
- if (!sr->autocomp_active)
- return;
-
- if (!sr_class || !(sr_class->disable)) {
- dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
- "registered\n", __func__);
- return;
- }
-
- sr_class->disable(sr, 1);
-}
-
-/**
- * omap_sr_register_pmic() - API to register pmic specific info.
- * @pmic_data: The structure containing pmic specific data.
- *
- * This API is to be called from the PMIC specific code to register with
- * smartreflex driver pmic specific info. Currently the only info required
- * is the smartreflex init on the PMIC side.
- */
-void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data)
-{
- if (!pmic_data) {
- pr_warning("%s: Trying to register NULL PMIC data structure"
- "with smartreflex\n", __func__);
- return;
- }
-
- sr_pmic_data = pmic_data;
-}
-
-/* PM Debug FS entries to enable and disable smartreflex. */
-static int omap_sr_autocomp_show(void *data, u64 *val)
-{
- struct omap_sr *sr_info = data;
-
- if (!sr_info) {
- pr_warning("%s: omap_sr struct not found\n", __func__);
- return -EINVAL;
- }
-
- *val = sr_info->autocomp_active;
-
- return 0;
-}
-
-static int omap_sr_autocomp_store(void *data, u64 val)
-{
- struct omap_sr *sr_info = data;
-
- if (!sr_info) {
- pr_warning("%s: omap_sr struct not found\n", __func__);
- return -EINVAL;
- }
-
- /* Sanity check */
- if (val > 1) {
- pr_warning("%s: Invalid argument %lld\n", __func__, val);
- return -EINVAL;
- }
-
- /* control enable/disable only if there is a delta in value */
- if (sr_info->autocomp_active != val) {
- if (!val)
- sr_stop_vddautocomp(sr_info);
- else
- sr_start_vddautocomp(sr_info);
- }
-
- return 0;
-}
-
-DEFINE_SIMPLE_ATTRIBUTE(pm_sr_fops, omap_sr_autocomp_show,
- omap_sr_autocomp_store, "%llu\n");
-
-static int __init omap_sr_probe(struct platform_device *pdev)
-{
- struct omap_sr *sr_info;
- struct omap_sr_data *pdata = pdev->dev.platform_data;
- struct resource *mem, *irq;
- struct dentry *nvalue_dir;
- int i, ret = 0;
-
- sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
- if (!sr_info) {
- dev_err(&pdev->dev, "%s: unable to allocate sr_info\n",
- __func__);
- return -ENOMEM;
- }
-
- platform_set_drvdata(pdev, sr_info);
-
- if (!pdata) {
- dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
- ret = -EINVAL;
- goto err_free_devinfo;
- }
-
- mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!mem) {
- dev_err(&pdev->dev, "%s: no mem resource\n", __func__);
- ret = -ENODEV;
- goto err_free_devinfo;
- }
-
- mem = request_mem_region(mem->start, resource_size(mem),
- dev_name(&pdev->dev));
- if (!mem) {
- dev_err(&pdev->dev, "%s: no mem region\n", __func__);
- ret = -EBUSY;
- goto err_free_devinfo;
- }
-
- irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
-
- pm_runtime_enable(&pdev->dev);
- pm_runtime_irq_safe(&pdev->dev);
-
- sr_info->name = kasprintf(GFP_KERNEL, "sr_%s", pdata->name);
- if (!sr_info->name) {
- dev_err(&pdev->dev, "%s: Unable to alloc SR instance name\n",
- __func__);
- ret = -ENOMEM;
- goto err_release_region;
- }
-
- sr_info->pdev = pdev;
- sr_info->srid = pdev->id;
- sr_info->voltdm = pdata->voltdm;
- sr_info->nvalue_table = pdata->nvalue_table;
- sr_info->nvalue_count = pdata->nvalue_count;
- sr_info->senn_mod = pdata->senn_mod;
- sr_info->senp_mod = pdata->senp_mod;
- sr_info->autocomp_active = false;
- sr_info->ip_type = pdata->ip_type;
- sr_info->base = ioremap(mem->start, resource_size(mem));
- if (!sr_info->base) {
- dev_err(&pdev->dev, "%s: ioremap fail\n", __func__);
- ret = -ENOMEM;
- goto err_release_region;
- }
-
- if (irq)
- sr_info->irq = irq->start;
-
- sr_set_clk_length(sr_info);
- sr_set_regfields(sr_info);
-
- list_add(&sr_info->node, &sr_list);
-
- /*
- * Call into late init to do intializations that require
- * both sr driver and sr class driver to be initiallized.
- */
- if (sr_class) {
- ret = sr_late_init(sr_info);
- if (ret) {
- pr_warning("%s: Error in SR late init\n", __func__);
- goto err_iounmap;
- }
- }
-
- dev_info(&pdev->dev, "%s: SmartReflex driver initialized\n", __func__);
- if (!sr_dbg_dir) {
- sr_dbg_dir = debugfs_create_dir("smartreflex", NULL);
- if (IS_ERR_OR_NULL(sr_dbg_dir)) {
- ret = PTR_ERR(sr_dbg_dir);
- pr_err("%s:sr debugfs dir creation failed(%d)\n",
- __func__, ret);
- goto err_iounmap;
- }
- }
-
- sr_info->dbg_dir = debugfs_create_dir(sr_info->name, sr_dbg_dir);
- if (IS_ERR_OR_NULL(sr_info->dbg_dir)) {
- dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n",
- __func__);
- ret = PTR_ERR(sr_info->dbg_dir);
- goto err_free_name;
- }
-
- (void) debugfs_create_file("autocomp", S_IRUGO | S_IWUSR,
- sr_info->dbg_dir, (void *)sr_info, &pm_sr_fops);
- (void) debugfs_create_x32("errweight", S_IRUGO, sr_info->dbg_dir,
- &sr_info->err_weight);
- (void) debugfs_create_x32("errmaxlimit", S_IRUGO, sr_info->dbg_dir,
- &sr_info->err_maxlimit);
-
- nvalue_dir = debugfs_create_dir("nvalue", sr_info->dbg_dir);
- if (IS_ERR_OR_NULL(nvalue_dir)) {
- dev_err(&pdev->dev, "%s: Unable to create debugfs directory"
- "for n-values\n", __func__);
- ret = PTR_ERR(nvalue_dir);
- goto err_debugfs;
- }
-
- if (sr_info->nvalue_count == 0 || !sr_info->nvalue_table) {
- dev_warn(&pdev->dev, "%s: %s: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values\n",
- __func__, sr_info->name);
- ret = -ENODATA;
- goto err_debugfs;
- }
-
- for (i = 0; i < sr_info->nvalue_count; i++) {
- char name[NVALUE_NAME_LEN + 1];
-
- snprintf(name, sizeof(name), "volt_%lu",
- sr_info->nvalue_table[i].volt_nominal);
- (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
- &(sr_info->nvalue_table[i].nvalue));
- snprintf(name, sizeof(name), "errminlimit_%lu",
- sr_info->nvalue_table[i].volt_nominal);
- (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
- &(sr_info->nvalue_table[i].errminlimit));
- }
-
- return ret;
-
-err_debugfs:
- debugfs_remove_recursive(sr_info->dbg_dir);
-err_free_name:
- kfree(sr_info->name);
-err_iounmap:
- list_del(&sr_info->node);
- iounmap(sr_info->base);
-err_release_region:
- release_mem_region(mem->start, resource_size(mem));
-err_free_devinfo:
- kfree(sr_info);
-
- return ret;
-}
-
-static int __devexit omap_sr_remove(struct platform_device *pdev)
-{
- struct omap_sr_data *pdata = pdev->dev.platform_data;
- struct omap_sr *sr_info;
- struct resource *mem;
-
- if (!pdata) {
- dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
- return -EINVAL;
- }
-
- sr_info = _sr_lookup(pdata->voltdm);
- if (IS_ERR(sr_info)) {
- dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
- __func__);
- return PTR_ERR(sr_info);
- }
-
- if (sr_info->autocomp_active)
- sr_stop_vddautocomp(sr_info);
- if (sr_info->dbg_dir)
- debugfs_remove_recursive(sr_info->dbg_dir);
-
- list_del(&sr_info->node);
- iounmap(sr_info->base);
- kfree(sr_info->name);
- kfree(sr_info);
- mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(mem->start, resource_size(mem));
-
- return 0;
-}
-
-static void __devexit omap_sr_shutdown(struct platform_device *pdev)
-{
- struct omap_sr_data *pdata = pdev->dev.platform_data;
- struct omap_sr *sr_info;
-
- if (!pdata) {
- dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
- return;
- }
-
- sr_info = _sr_lookup(pdata->voltdm);
- if (IS_ERR(sr_info)) {
- dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
- __func__);
- return;
- }
-
- if (sr_info->autocomp_active)
- sr_stop_vddautocomp(sr_info);
-
- return;
-}
-
-static struct platform_driver smartreflex_driver = {
- .remove = __devexit_p(omap_sr_remove),
- .shutdown = __devexit_p(omap_sr_shutdown),
- .driver = {
- .name = "smartreflex",
- },
-};
-
-static int __init sr_init(void)
-{
- int ret = 0;
-
- /*
- * sr_init is a late init. If by then a pmic specific API is not
- * registered either there is no need for anything to be done on
- * the PMIC side or somebody has forgotten to register a PMIC
- * handler. Warn for the second condition.
- */
- if (sr_pmic_data && sr_pmic_data->sr_pmic_init)
- sr_pmic_data->sr_pmic_init();
- else
- pr_warning("%s: No PMIC hook to init smartreflex\n", __func__);
-
- ret = platform_driver_probe(&smartreflex_driver, omap_sr_probe);
- if (ret) {
- pr_err("%s: platform driver register failed for SR\n",
- __func__);
- return ret;
- }
-
- return 0;
-}
-late_initcall(sr_init);
-
-static void __exit sr_exit(void)
-{
- platform_driver_unregister(&smartreflex_driver);
-}
-module_exit(sr_exit);
-
-MODULE_DESCRIPTION("OMAP Smartreflex Driver");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:" DRIVER_NAME);
-MODULE_AUTHOR("Texas Instruments Inc");
diff --git a/arch/arm/mach-omap2/smartreflex.h b/arch/arm/mach-omap2/smartreflex.h
deleted file mode 100644
index 754f6aa..0000000
--- a/arch/arm/mach-omap2/smartreflex.h
+++ /dev/null
@@ -1,238 +0,0 @@
-/*
- * OMAP Smartreflex Defines and Routines
- *
- * Author: Thara Gopinath <thara@...com>
- *
- * Copyright (C) 2010 Texas Instruments, Inc.
- * Thara Gopinath <thara@...com>
- *
- * Copyright (C) 2008 Nokia Corporation
- * Kalle Jokiniemi
- *
- * Copyright (C) 2007 Texas Instruments, Inc.
- * Lesly A M <x0080970@...com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __DRIVERS_POWER_AVS_SMARTREFLEX_H
-#define __DRIVERS_POWER_AVS_SMARTREFLEX_H
-
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/power/smartreflex.h>
-
-#include <plat/voltage.h>
-
-/*
- * Different Smartreflex IPs version. The v1 is the 65nm version used in
- * OMAP3430. The v2 is the update for the 45nm version of the IP
- * used in OMAP3630 and OMAP4430
- */
-#define SR_TYPE_V1 1
-#define SR_TYPE_V2 2
-
-/* SMART REFLEX REG ADDRESS OFFSET */
-#define SRCONFIG 0x00
-#define SRSTATUS 0x04
-#define SENVAL 0x08
-#define SENMIN 0x0C
-#define SENMAX 0x10
-#define SENAVG 0x14
-#define AVGWEIGHT 0x18
-#define NVALUERECIPROCAL 0x1c
-#define SENERROR_V1 0x20
-#define ERRCONFIG_V1 0x24
-#define IRQ_EOI 0x20
-#define IRQSTATUS_RAW 0x24
-#define IRQSTATUS 0x28
-#define IRQENABLE_SET 0x2C
-#define IRQENABLE_CLR 0x30
-#define SENERROR_V2 0x34
-#define ERRCONFIG_V2 0x38
-
-/* Bit/Shift Positions */
-
-/* SRCONFIG */
-#define SRCONFIG_ACCUMDATA_SHIFT 22
-#define SRCONFIG_SRCLKLENGTH_SHIFT 12
-#define SRCONFIG_SENNENABLE_V1_SHIFT 5
-#define SRCONFIG_SENPENABLE_V1_SHIFT 3
-#define SRCONFIG_SENNENABLE_V2_SHIFT 1
-#define SRCONFIG_SENPENABLE_V2_SHIFT 0
-#define SRCONFIG_CLKCTRL_SHIFT 0
-
-#define SRCONFIG_ACCUMDATA_MASK (0x3ff << 22)
-
-#define SRCONFIG_SRENABLE BIT(11)
-#define SRCONFIG_SENENABLE BIT(10)
-#define SRCONFIG_ERRGEN_EN BIT(9)
-#define SRCONFIG_MINMAXAVG_EN BIT(8)
-#define SRCONFIG_DELAYCTRL BIT(2)
-
-/* AVGWEIGHT */
-#define AVGWEIGHT_SENPAVGWEIGHT_SHIFT 2
-#define AVGWEIGHT_SENNAVGWEIGHT_SHIFT 0
-
-/* NVALUERECIPROCAL */
-#define NVALUERECIPROCAL_SENPGAIN_SHIFT 20
-#define NVALUERECIPROCAL_SENNGAIN_SHIFT 16
-#define NVALUERECIPROCAL_RNSENP_SHIFT 8
-#define NVALUERECIPROCAL_RNSENN_SHIFT 0
-
-/* ERRCONFIG */
-#define ERRCONFIG_ERRWEIGHT_SHIFT 16
-#define ERRCONFIG_ERRMAXLIMIT_SHIFT 8
-#define ERRCONFIG_ERRMINLIMIT_SHIFT 0
-
-#define SR_ERRWEIGHT_MASK (0x07 << 16)
-#define SR_ERRMAXLIMIT_MASK (0xff << 8)
-#define SR_ERRMINLIMIT_MASK (0xff << 0)
-
-#define ERRCONFIG_VPBOUNDINTEN_V1 BIT(31)
-#define ERRCONFIG_VPBOUNDINTST_V1 BIT(30)
-#define ERRCONFIG_MCUACCUMINTEN BIT(29)
-#define ERRCONFIG_MCUACCUMINTST BIT(28)
-#define ERRCONFIG_MCUVALIDINTEN BIT(27)
-#define ERRCONFIG_MCUVALIDINTST BIT(26)
-#define ERRCONFIG_MCUBOUNDINTEN BIT(25)
-#define ERRCONFIG_MCUBOUNDINTST BIT(24)
-#define ERRCONFIG_MCUDISACKINTEN BIT(23)
-#define ERRCONFIG_VPBOUNDINTST_V2 BIT(23)
-#define ERRCONFIG_MCUDISACKINTST BIT(22)
-#define ERRCONFIG_VPBOUNDINTEN_V2 BIT(22)
-
-#define ERRCONFIG_STATUS_V1_MASK (ERRCONFIG_VPBOUNDINTST_V1 | \
- ERRCONFIG_MCUACCUMINTST | \
- ERRCONFIG_MCUVALIDINTST | \
- ERRCONFIG_MCUBOUNDINTST | \
- ERRCONFIG_MCUDISACKINTST)
-/* IRQSTATUS */
-#define IRQSTATUS_MCUACCUMINT BIT(3)
-#define IRQSTATUS_MCVALIDINT BIT(2)
-#define IRQSTATUS_MCBOUNDSINT BIT(1)
-#define IRQSTATUS_MCUDISABLEACKINT BIT(0)
-
-/* IRQENABLE_SET and IRQENABLE_CLEAR */
-#define IRQENABLE_MCUACCUMINT BIT(3)
-#define IRQENABLE_MCUVALIDINT BIT(2)
-#define IRQENABLE_MCUBOUNDSINT BIT(1)
-#define IRQENABLE_MCUDISABLEACKINT BIT(0)
-
-/* Common Bit values */
-
-#define SRCLKLENGTH_12MHZ_SYSCLK 0x3c
-#define SRCLKLENGTH_13MHZ_SYSCLK 0x41
-#define SRCLKLENGTH_19MHZ_SYSCLK 0x60
-#define SRCLKLENGTH_26MHZ_SYSCLK 0x82
-#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0
-
-/*
- * 3430 specific values. Maybe these should be passed from board file or
- * pmic structures.
- */
-#define OMAP3430_SR_ACCUMDATA 0x1f4
-
-#define OMAP3430_SR1_SENPAVGWEIGHT 0x03
-#define OMAP3430_SR1_SENNAVGWEIGHT 0x03
-
-#define OMAP3430_SR2_SENPAVGWEIGHT 0x01
-#define OMAP3430_SR2_SENNAVGWEIGHT 0x01
-
-#define OMAP3430_SR_ERRWEIGHT 0x04
-#define OMAP3430_SR_ERRMAXLIMIT 0x02
-
-/**
- * test_cond_timeout - busy-loop, testing a condition
- * @cond: condition to test until it evaluates to true
- * @timeout: maximum number of microseconds in the timeout
- * @index: loop index (integer)
- *
- * Loop waiting for @cond to become true or until at least @timeout
- * microseconds have passed. To use, define some integer @index in the
- * calling code. After running, if @index == @timeout, then the loop has
- * timed out.
- *
- * Copied from omap_test_timeout
- */
-#define sr_test_cond_timeout(cond, timeout, index) \
-({ \
- for (index = 0; index < timeout; index++) { \
- if (cond) \
- break; \
- udelay(1); \
- } \
-})
-
-/**
- * struct omap_sr_pmic_data - Strucutre to be populated by pmic code to pass
- * pmic specific info to smartreflex driver
- *
- * @sr_pmic_init: API to initialize smartreflex on the PMIC side.
- */
-struct omap_sr_pmic_data {
- void (*sr_pmic_init) (void);
-};
-
-
-#ifdef CONFIG_POWER_AVS_OMAP
-/*
- * The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR.
- * The smartreflex class driver should pass the class type.
- * Should be used to populate the class_type field of the
- * omap_smartreflex_class_data structure.
- */
-#define SR_CLASS1 0x1
-#define SR_CLASS2 0x2
-#define SR_CLASS3 0x3
-
-/**
- * struct omap_sr_class_data - Smartreflex class driver info
- *
- * @enable: API to enable a particular class smaartreflex.
- * @disable: API to disable a particular class smartreflex.
- * @configure: API to configure a particular class smartreflex.
- * @notify: API to notify the class driver about an event in SR.
- * Not needed for class3.
- * @notify_flags: specify the events to be notified to the class driver
- * @class_type: specify which smartreflex class.
- * Can be used by the SR driver to take any class
- * based decisions.
- */
-struct omap_sr_class_data {
- int (*enable)(struct omap_sr *sr);
- int (*disable)(struct omap_sr *sr, int is_volt_reset);
- int (*configure)(struct omap_sr *sr);
- int (*notify)(struct omap_sr *sr, u32 status);
- u8 notify_flags;
- u8 class_type;
-};
-
-/* Smartreflex module enable/disable interface */
-void omap_sr_enable(struct voltagedomain *voltdm);
-void omap_sr_disable(struct voltagedomain *voltdm);
-void omap_sr_disable_reset_volt(struct voltagedomain *voltdm);
-
-/* API to register the pmic specific data with the smartreflex driver. */
-void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data);
-
-/* Smartreflex driver hooks to be called from Smartreflex class driver */
-int sr_enable(struct voltagedomain *voltdm, unsigned long volt);
-void sr_disable(struct voltagedomain *voltdm);
-int sr_configure_errgen(struct voltagedomain *voltdm);
-int sr_disable_errgen(struct voltagedomain *voltdm);
-int sr_configure_minmax(struct voltagedomain *voltdm);
-
-/* API to register the smartreflex class driver with the smartreflex driver */
-int sr_register_class(struct omap_sr_class_data *class_data);
-#else
-static inline void omap_sr_enable(struct voltagedomain *voltdm) {}
-static inline void omap_sr_disable(struct voltagedomain *voltdm) {}
-static inline void omap_sr_disable_reset_volt(
- struct voltagedomain *voltdm) {}
-static inline void omap_sr_register_pmic(
- struct omap_sr_pmic_data *pmic_data) {}
-#endif
-#endif
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
index 6ec9237..85f70e6 100644
--- a/arch/arm/plat-omap/Kconfig
+++ b/arch/arm/plat-omap/Kconfig
@@ -44,24 +44,9 @@ config OMAP_DEBUG_LEDS
depends on OMAP_DEBUG_DEVICES
default y if LEDS_CLASS
-menuconfig POWER_AVS
- tristate "Adaptive Voltage Scaling class support"
- help
- AVS is a power management technique which finely controls the
- operating voltage of a device in order to optimize (i.e. reduce)
- its power consumption.
- At a given operating point the voltage is adapted depending on
- static factors (chip manufacturing process) and dynamic factors
- (temperature depending performance).
- AVS is also called SmartReflex on OMAP devices.
-
- Say Y here to enable Adaptive Voltage Scaling class support.
-
-if POWER_AVS
-
config POWER_AVS_OMAP
bool "AVS support for the OMAP IP versions 1&2"
- depends on (ARCH_OMAP3 || ARCH_OMAP4) && PM
+ depends on POWER_AVS && (ARCH_OMAP3 || ARCH_OMAP4) && PM
help
Say Y to enable AVS support on OMAP containing the version 1 or
version 2 of the SmartReflex IP.
@@ -88,8 +73,6 @@ config POWER_AVS_OMAP_CLASS3
Class 3 implementation of Smartreflex employs continuous hardware
voltage calibration.
-endif # POWER_AVS
-
config OMAP_RESET_CLOCKS
bool "Reset unused clocks during boot"
depends on ARCH_OMAP
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 3a8daf8..06f991e 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -275,3 +275,5 @@ config CHARGER_MAX8998
platform data of MAX8998/LP3974 PMICs.
endif # POWER_SUPPLY
+
+source "drivers/power/avs/Kconfig"
diff --git a/drivers/power/Makefile b/drivers/power/Makefile
index e429008..e4a8fd2 100644
--- a/drivers/power/Makefile
+++ b/drivers/power/Makefile
@@ -41,3 +41,5 @@ obj-$(CONFIG_CHARGER_GPIO) += gpio-charger.o
obj-$(CONFIG_CHARGER_MANAGER) += charger-manager.o
obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o
obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o
+
+obj-$(CONFIG_POWER_AVS) += avs/
diff --git a/drivers/power/avs/Kconfig b/drivers/power/avs/Kconfig
new file mode 100644
index 0000000..18493f7
--- /dev/null
+++ b/drivers/power/avs/Kconfig
@@ -0,0 +1,12 @@
+menuconfig POWER_AVS
+ tristate "Adaptive Voltage Scaling class support"
+ help
+ AVS is a power management technique which finely controls the
+ operating voltage of a device in order to optimize (i.e. reduce)
+ its power consumption.
+ At a given operating point the voltage is adapted depending on
+ static factors (chip manufacturing process) and dynamic factors
+ (temperature depending performance).
+ AVS is also called SmartReflex on OMAP devices.
+
+ Say Y here to enable Adaptive Voltage Scaling class support.
diff --git a/drivers/power/avs/Makefile b/drivers/power/avs/Makefile
new file mode 100644
index 0000000..ac72ec5
--- /dev/null
+++ b/drivers/power/avs/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_POWER_AVS_OMAP) += smartreflex.o
+obj-$(CONFIG_POWER_AVS_OMAP_CLASS3) += smartreflex-class3.o
diff --git a/drivers/power/avs/smartreflex-class3.c b/drivers/power/avs/smartreflex-class3.c
new file mode 100644
index 0000000..413a07b
--- /dev/null
+++ b/drivers/power/avs/smartreflex-class3.c
@@ -0,0 +1,61 @@
+/*
+ * Smart reflex Class 3 specific implementations
+ *
+ * Author: Thara Gopinath <thara@...com>
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@...com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "smartreflex.h"
+#include <plat/voltage.h>
+
+static int sr_class3_enable(struct omap_sr *sr)
+{
+ unsigned long volt = voltdm_get_voltage(sr->voltdm);
+
+ if (!volt) {
+ pr_warning("%s: Curr voltage unknown. Cannot enable %s\n",
+ __func__, sr->name);
+ return -ENODATA;
+ }
+
+ omap_vp_enable(sr->voltdm);
+ return sr_enable(sr->voltdm, volt);
+}
+
+static int sr_class3_disable(struct omap_sr *sr, int is_volt_reset)
+{
+ sr_disable_errgen(sr->voltdm);
+ omap_vp_disable(sr->voltdm);
+ sr_disable(sr->voltdm);
+ if (is_volt_reset)
+ voltdm_reset(sr->voltdm);
+
+ return 0;
+}
+
+static int sr_class3_configure(struct omap_sr *sr)
+{
+ return sr_configure_errgen(sr->voltdm);
+}
+
+/* SR class3 structure */
+static struct omap_sr_class_data class3_data = {
+ .enable = sr_class3_enable,
+ .disable = sr_class3_disable,
+ .configure = sr_class3_configure,
+ .class_type = SR_CLASS3,
+};
+
+/* Smartreflex Class3 init API to be called from board file */
+static int __init sr_class3_init(void)
+{
+ pr_info("SmartReflex Class3 initialized\n");
+ return sr_register_class(&class3_data);
+}
+late_initcall(sr_class3_init);
diff --git a/drivers/power/avs/smartreflex.c b/drivers/power/avs/smartreflex.c
new file mode 100644
index 0000000..d3973cb
--- /dev/null
+++ b/drivers/power/avs/smartreflex.c
@@ -0,0 +1,1118 @@
+/*
+ * OMAP SmartReflex Voltage Control
+ *
+ * Author: Thara Gopinath <thara@...com>
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@...com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@...com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/pm_runtime.h>
+#include <linux/power/smartreflex.h>
+
+#include "smartreflex.h"
+
+#define SMARTREFLEX_NAME_LEN 16
+#define NVALUE_NAME_LEN 40
+#define SR_DISABLE_TIMEOUT 200
+
+/* sr_list contains all the instances of smartreflex module */
+static LIST_HEAD(sr_list);
+
+static struct omap_sr_class_data *sr_class;
+static struct omap_sr_pmic_data *sr_pmic_data;
+static struct dentry *sr_dbg_dir;
+
+static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32 value)
+{
+ __raw_writel(value, (sr->base + offset));
+}
+
+static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
+ u32 value)
+{
+ u32 reg_val;
+
+ /*
+ * Smartreflex error config register is special as it contains
+ * certain status bits which if written a 1 into means a clear
+ * of those bits. So in order to make sure no accidental write of
+ * 1 happens to those status bits, do a clear of them in the read
+ * value. This mean this API doesn't rewrite values in these bits
+ * if they are currently set, but does allow the caller to write
+ * those bits.
+ */
+ if (sr->ip_type == SR_TYPE_V1 && offset == ERRCONFIG_V1)
+ mask |= ERRCONFIG_STATUS_V1_MASK;
+ else if (sr->ip_type == SR_TYPE_V2 && offset == ERRCONFIG_V2)
+ mask |= ERRCONFIG_VPBOUNDINTST_V2;
+
+ reg_val = __raw_readl(sr->base + offset);
+ reg_val &= ~mask;
+
+ value &= mask;
+
+ reg_val |= value;
+
+ __raw_writel(reg_val, (sr->base + offset));
+}
+
+static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)
+{
+ return __raw_readl(sr->base + offset);
+}
+
+static struct omap_sr *_sr_lookup(struct voltagedomain *voltdm)
+{
+ struct omap_sr *sr_info;
+
+ if (!voltdm) {
+ pr_err("%s: Null voltage domain passed!\n", __func__);
+ return ERR_PTR(-EINVAL);
+ }
+
+ list_for_each_entry(sr_info, &sr_list, node) {
+ if (voltdm == sr_info->voltdm)
+ return sr_info;
+ }
+
+ return ERR_PTR(-ENODATA);
+}
+
+static irqreturn_t sr_interrupt(int irq, void *data)
+{
+ struct omap_sr *sr_info = data;
+ u32 status = 0;
+
+ switch (sr_info->ip_type) {
+ case SR_TYPE_V1:
+ /* Read the status bits */
+ status = sr_read_reg(sr_info, ERRCONFIG_V1);
+
+ /* Clear them by writing back */
+ sr_write_reg(sr_info, ERRCONFIG_V1, status);
+ break;
+ case SR_TYPE_V2:
+ /* Read the status bits */
+ status = sr_read_reg(sr_info, IRQSTATUS);
+
+ /* Clear them by writing back */
+ sr_write_reg(sr_info, IRQSTATUS, status);
+ break;
+ default:
+ dev_err(&sr_info->pdev->dev, "UNKNOWN IP type %d\n",
+ sr_info->ip_type);
+ return IRQ_NONE;
+ }
+
+ if (sr_class->notify)
+ sr_class->notify(sr_info, status);
+
+ return IRQ_HANDLED;
+}
+
+static void sr_set_clk_length(struct omap_sr *sr)
+{
+ struct clk *sys_ck;
+ u32 sys_clk_speed;
+
+ if (cpu_is_omap34xx())
+ sys_ck = clk_get(NULL, "sys_ck");
+ else
+ sys_ck = clk_get(NULL, "sys_clkin_ck");
+
+ if (IS_ERR(sys_ck)) {
+ dev_err(&sr->pdev->dev, "%s: unable to get sys clk\n",
+ __func__);
+ return;
+ }
+
+ sys_clk_speed = clk_get_rate(sys_ck);
+ clk_put(sys_ck);
+
+ switch (sys_clk_speed) {
+ case 12000000:
+ sr->clk_length = SRCLKLENGTH_12MHZ_SYSCLK;
+ break;
+ case 13000000:
+ sr->clk_length = SRCLKLENGTH_13MHZ_SYSCLK;
+ break;
+ case 19200000:
+ sr->clk_length = SRCLKLENGTH_19MHZ_SYSCLK;
+ break;
+ case 26000000:
+ sr->clk_length = SRCLKLENGTH_26MHZ_SYSCLK;
+ break;
+ case 38400000:
+ sr->clk_length = SRCLKLENGTH_38MHZ_SYSCLK;
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Invalid sysclk value: %d\n",
+ __func__, sys_clk_speed);
+ break;
+ }
+}
+
+static void sr_set_regfields(struct omap_sr *sr)
+{
+ /*
+ * For time being these values are defined in smartreflex.h
+ * and populated during init. May be they can be moved to board
+ * file or pmic specific data structure. In that case these structure
+ * fields will have to be populated using the pdata or pmic structure.
+ */
+ if (cpu_is_omap34xx() || cpu_is_omap44xx()) {
+ sr->err_weight = OMAP3430_SR_ERRWEIGHT;
+ sr->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT;
+ sr->accum_data = OMAP3430_SR_ACCUMDATA;
+ if (!(strcmp(sr->name, "sr_mpu_iva"))) {
+ sr->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT;
+ sr->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT;
+ } else {
+ sr->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT;
+ sr->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT;
+ }
+ }
+}
+
+static void sr_start_vddautocomp(struct omap_sr *sr)
+{
+ if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
+ dev_warn(&sr->pdev->dev,
+ "%s: smartreflex class driver not registered\n",
+ __func__);
+ return;
+ }
+
+ if (!sr_class->enable(sr))
+ sr->autocomp_active = true;
+}
+
+static void sr_stop_vddautocomp(struct omap_sr *sr)
+{
+ if (!sr_class || !(sr_class->disable)) {
+ dev_warn(&sr->pdev->dev,
+ "%s: smartreflex class driver not registered\n",
+ __func__);
+ return;
+ }
+
+ if (sr->autocomp_active) {
+ sr_class->disable(sr, 1);
+ sr->autocomp_active = false;
+ }
+}
+
+/*
+ * This function handles the intializations which have to be done
+ * only when both sr device and class driver regiter has
+ * completed. This will be attempted to be called from both sr class
+ * driver register and sr device intializtion API's. Only one call
+ * will ultimately succeed.
+ *
+ * Currently this function registers interrupt handler for a particular SR
+ * if smartreflex class driver is already registered and has
+ * requested for interrupts and the SR interrupt line in present.
+ */
+static int sr_late_init(struct omap_sr *sr_info)
+{
+ struct omap_sr_data *pdata = sr_info->pdev->dev.platform_data;
+ struct resource *mem;
+ int ret = 0;
+
+ if (sr_class->notify && sr_class->notify_flags && sr_info->irq) {
+ ret = request_irq(sr_info->irq, sr_interrupt,
+ 0, sr_info->name, sr_info);
+ if (ret)
+ goto error;
+ disable_irq(sr_info->irq);
+ }
+
+ if (pdata && pdata->enable_on_init)
+ sr_start_vddautocomp(sr_info);
+
+ return ret;
+
+error:
+ iounmap(sr_info->base);
+ mem = platform_get_resource(sr_info->pdev, IORESOURCE_MEM, 0);
+ release_mem_region(mem->start, resource_size(mem));
+ list_del(&sr_info->node);
+ dev_err(&sr_info->pdev->dev, "%s: ERROR in registering"
+ "interrupt handler. Smartreflex will"
+ "not function as desired\n", __func__);
+ kfree(sr_info);
+
+ return ret;
+}
+
+static void sr_v1_disable(struct omap_sr *sr)
+{
+ int timeout = 0;
+ int errconf_val = ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
+ ERRCONFIG_MCUBOUNDINTST;
+
+ /* Enable MCUDisableAcknowledge interrupt */
+ sr_modify_reg(sr, ERRCONFIG_V1,
+ ERRCONFIG_MCUDISACKINTEN, ERRCONFIG_MCUDISACKINTEN);
+
+ /* SRCONFIG - disable SR */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
+
+ /* Disable all other SR interrupts and clear the status as needed */
+ if (sr_read_reg(sr, ERRCONFIG_V1) & ERRCONFIG_VPBOUNDINTST_V1)
+ errconf_val |= ERRCONFIG_VPBOUNDINTST_V1;
+ sr_modify_reg(sr, ERRCONFIG_V1,
+ (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
+ ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN_V1),
+ errconf_val);
+
+ /*
+ * Wait for SR to be disabled.
+ * wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us.
+ */
+ sr_test_cond_timeout((sr_read_reg(sr, ERRCONFIG_V1) &
+ ERRCONFIG_MCUDISACKINTST), SR_DISABLE_TIMEOUT,
+ timeout);
+
+ if (timeout >= SR_DISABLE_TIMEOUT)
+ dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
+ __func__);
+
+ /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
+ sr_modify_reg(sr, ERRCONFIG_V1, ERRCONFIG_MCUDISACKINTEN,
+ ERRCONFIG_MCUDISACKINTST);
+}
+
+static void sr_v2_disable(struct omap_sr *sr)
+{
+ int timeout = 0;
+
+ /* Enable MCUDisableAcknowledge interrupt */
+ sr_write_reg(sr, IRQENABLE_SET, IRQENABLE_MCUDISABLEACKINT);
+
+ /* SRCONFIG - disable SR */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
+
+ /*
+ * Disable all other SR interrupts and clear the status
+ * write to status register ONLY on need basis - only if status
+ * is set.
+ */
+ if (sr_read_reg(sr, ERRCONFIG_V2) & ERRCONFIG_VPBOUNDINTST_V2)
+ sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+ ERRCONFIG_VPBOUNDINTST_V2);
+ else
+ sr_modify_reg(sr, ERRCONFIG_V2, ERRCONFIG_VPBOUNDINTEN_V2,
+ 0x0);
+ sr_write_reg(sr, IRQENABLE_CLR, (IRQENABLE_MCUACCUMINT |
+ IRQENABLE_MCUVALIDINT |
+ IRQENABLE_MCUBOUNDSINT));
+ sr_write_reg(sr, IRQSTATUS, (IRQSTATUS_MCUACCUMINT |
+ IRQSTATUS_MCVALIDINT |
+ IRQSTATUS_MCBOUNDSINT));
+
+ /*
+ * Wait for SR to be disabled.
+ * wait until IRQSTATUS.MCUDISACKINTST = 1. Typical latency is 1us.
+ */
+ sr_test_cond_timeout((sr_read_reg(sr, IRQSTATUS) &
+ IRQSTATUS_MCUDISABLEACKINT), SR_DISABLE_TIMEOUT,
+ timeout);
+
+ if (timeout >= SR_DISABLE_TIMEOUT)
+ dev_warn(&sr->pdev->dev, "%s: Smartreflex disable timedout\n",
+ __func__);
+
+ /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt */
+ sr_write_reg(sr, IRQENABLE_CLR, IRQENABLE_MCUDISABLEACKINT);
+ sr_write_reg(sr, IRQSTATUS, IRQSTATUS_MCUDISABLEACKINT);
+}
+
+static struct omap_sr_nvalue_table *sr_retrieve_nvalue_row(
+ struct omap_sr *sr,
+ unsigned long volt_nominal)
+{
+ int i;
+
+ if (!sr->nvalue_table) {
+ dev_warn(&sr->pdev->dev, "%s: Missing ntarget value table\n",
+ __func__);
+ return NULL;
+ }
+
+ for (i = 0; i < sr->nvalue_count; i++) {
+ if (sr->nvalue_table[i].volt_nominal == volt_nominal)
+ return &sr->nvalue_table[i];
+ }
+
+ return NULL;
+}
+
+/* Public Functions */
+
+/**
+ * sr_configure_errgen() - Configures the smrtreflex to perform AVS using the
+ * error generator module.
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * configure the error generator module inside the smartreflex module.
+ * SR settings if using the ERROR module inside Smartreflex.
+ * SR CLASS 3 by default uses only the ERROR module where as
+ * SR CLASS 2 can choose between ERROR module and MINMAXAVG
+ * module. Returns 0 on success and error value in case of failure.
+ */
+int sr_configure_errgen(struct voltagedomain *voltdm)
+{
+ u32 sr_config, sr_errconfig, errconfig_offs;
+ u32 vpboundint_en, vpboundint_st;
+ u32 senp_en = 0, senn_en = 0;
+ u8 senp_shift, senn_shift;
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return PTR_ERR(sr);
+ }
+
+ if (!sr->clk_length)
+ sr_set_clk_length(sr);
+
+ senp_en = sr->senp_mod;
+ senn_en = sr->senn_mod;
+
+ sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
+ SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN;
+
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ sr_config |= SRCONFIG_DELAYCTRL;
+ senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
+ senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
+ errconfig_offs = ERRCONFIG_V1;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
+ break;
+ case SR_TYPE_V2:
+ senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
+ senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
+ errconfig_offs = ERRCONFIG_V2;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
+ }
+
+ sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
+ sr_write_reg(sr, SRCONFIG, sr_config);
+ sr_errconfig = (sr->err_weight << ERRCONFIG_ERRWEIGHT_SHIFT) |
+ (sr->err_maxlimit << ERRCONFIG_ERRMAXLIMIT_SHIFT) |
+ (sr->err_minlimit << ERRCONFIG_ERRMINLIMIT_SHIFT);
+ sr_modify_reg(sr, errconfig_offs, (SR_ERRWEIGHT_MASK |
+ SR_ERRMAXLIMIT_MASK | SR_ERRMINLIMIT_MASK),
+ sr_errconfig);
+
+ /* Enabling the interrupts if the ERROR module is used */
+ sr_modify_reg(sr, errconfig_offs, (vpboundint_en | vpboundint_st),
+ vpboundint_en);
+
+ return 0;
+}
+
+/**
+ * sr_disable_errgen() - Disables SmartReflex AVS module's errgen component
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * disable the error generator module inside the smartreflex module.
+ *
+ * Returns 0 on success and error value in case of failure.
+ */
+int sr_disable_errgen(struct voltagedomain *voltdm)
+{
+ u32 errconfig_offs;
+ u32 vpboundint_en, vpboundint_st;
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return PTR_ERR(sr);
+ }
+
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ errconfig_offs = ERRCONFIG_V1;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V1;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V1;
+ break;
+ case SR_TYPE_V2:
+ errconfig_offs = ERRCONFIG_V2;
+ vpboundint_en = ERRCONFIG_VPBOUNDINTEN_V2;
+ vpboundint_st = ERRCONFIG_VPBOUNDINTST_V2;
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Disable the interrupts of ERROR module */
+ sr_modify_reg(sr, errconfig_offs, vpboundint_en | vpboundint_st, 0);
+
+ /* Disable the Sensor and errorgen */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN, 0);
+
+ return 0;
+}
+
+/**
+ * sr_configure_minmax() - Configures the smrtreflex to perform AVS using the
+ * minmaxavg module.
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * configure the minmaxavg module inside the smartreflex module.
+ * SR settings if using the ERROR module inside Smartreflex.
+ * SR CLASS 3 by default uses only the ERROR module where as
+ * SR CLASS 2 can choose between ERROR module and MINMAXAVG
+ * module. Returns 0 on success and error value in case of failure.
+ */
+int sr_configure_minmax(struct voltagedomain *voltdm)
+{
+ u32 sr_config, sr_avgwt;
+ u32 senp_en = 0, senn_en = 0;
+ u8 senp_shift, senn_shift;
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return PTR_ERR(sr);
+ }
+
+ if (!sr->clk_length)
+ sr_set_clk_length(sr);
+
+ senp_en = sr->senp_mod;
+ senn_en = sr->senn_mod;
+
+ sr_config = (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
+ SRCONFIG_SENENABLE |
+ (sr->accum_data << SRCONFIG_ACCUMDATA_SHIFT);
+
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ sr_config |= SRCONFIG_DELAYCTRL;
+ senn_shift = SRCONFIG_SENNENABLE_V1_SHIFT;
+ senp_shift = SRCONFIG_SENPENABLE_V1_SHIFT;
+ break;
+ case SR_TYPE_V2:
+ senn_shift = SRCONFIG_SENNENABLE_V2_SHIFT;
+ senp_shift = SRCONFIG_SENPENABLE_V2_SHIFT;
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
+ }
+
+ sr_config |= ((senn_en << senn_shift) | (senp_en << senp_shift));
+ sr_write_reg(sr, SRCONFIG, sr_config);
+ sr_avgwt = (sr->senp_avgweight << AVGWEIGHT_SENPAVGWEIGHT_SHIFT) |
+ (sr->senn_avgweight << AVGWEIGHT_SENNAVGWEIGHT_SHIFT);
+ sr_write_reg(sr, AVGWEIGHT, sr_avgwt);
+
+ /*
+ * Enabling the interrupts if MINMAXAVG module is used.
+ * TODO: check if all the interrupts are mandatory
+ */
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ sr_modify_reg(sr, ERRCONFIG_V1,
+ (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
+ ERRCONFIG_MCUBOUNDINTEN),
+ (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUACCUMINTST |
+ ERRCONFIG_MCUVALIDINTEN | ERRCONFIG_MCUVALIDINTST |
+ ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST));
+ break;
+ case SR_TYPE_V2:
+ sr_write_reg(sr, IRQSTATUS,
+ IRQSTATUS_MCUACCUMINT | IRQSTATUS_MCVALIDINT |
+ IRQSTATUS_MCBOUNDSINT | IRQSTATUS_MCUDISABLEACKINT);
+ sr_write_reg(sr, IRQENABLE_SET,
+ IRQENABLE_MCUACCUMINT | IRQENABLE_MCUVALIDINT |
+ IRQENABLE_MCUBOUNDSINT | IRQENABLE_MCUDISABLEACKINT);
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "%s: Trying to Configure smartreflex"
+ "module without specifying the ip\n", __func__);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * sr_enable() - Enables the smartreflex module.
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ * @volt: The voltage at which the Voltage domain associated with
+ * the smartreflex module is operating at.
+ * This is required only to program the correct Ntarget value.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * enable a smartreflex module. Returns 0 on success. Returns error
+ * value if the voltage passed is wrong or if ntarget value is wrong.
+ */
+int sr_enable(struct voltagedomain *voltdm, unsigned long volt)
+{
+ struct omap_sr *sr = _sr_lookup(voltdm);
+ struct omap_sr_nvalue_table *nvalue_row;
+ int ret;
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return PTR_ERR(sr);
+ }
+
+ nvalue_row = sr_retrieve_nvalue_row(sr, volt);
+ if (!nvalue_row) {
+ dev_warn(&sr->pdev->dev, "%s: failure getting SR data for this voltage %ld\n",
+ __func__, volt);
+ return -ENODATA;
+ }
+
+
+ /* errminlimit is opp dependent and hence linked to voltage */
+ sr->err_minlimit = nvalue_row->errminlimit;
+
+ pm_runtime_get_sync(&sr->pdev->dev);
+
+ /* Check if SR is already enabled. If yes do nothing */
+ if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE)
+ return 0;
+
+ /* Configure SR */
+ ret = sr_class->configure(sr);
+ if (ret)
+ return ret;
+
+ sr_write_reg(sr, NVALUERECIPROCAL, nvalue_row->nvalue);
+
+ /* SRCONFIG - enable SR */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, SRCONFIG_SRENABLE);
+ return 0;
+}
+
+/**
+ * sr_disable() - Disables the smartreflex module.
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the smartreflex class driver to
+ * disable a smartreflex module.
+ */
+void sr_disable(struct voltagedomain *voltdm)
+{
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return;
+ }
+
+ /* Check if SR clocks are already disabled. If yes do nothing */
+ if (pm_runtime_suspended(&sr->pdev->dev))
+ return;
+
+ /*
+ * Disable SR if only it is indeed enabled. Else just
+ * disable the clocks.
+ */
+ if (sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE) {
+ switch (sr->ip_type) {
+ case SR_TYPE_V1:
+ sr_v1_disable(sr);
+ break;
+ case SR_TYPE_V2:
+ sr_v2_disable(sr);
+ break;
+ default:
+ dev_err(&sr->pdev->dev, "UNKNOWN IP type %d\n",
+ sr->ip_type);
+ }
+ }
+
+ pm_runtime_put_sync_suspend(&sr->pdev->dev);
+}
+
+/**
+ * sr_register_class() - API to register a smartreflex class parameters.
+ * @class_data: The structure containing various sr class specific data.
+ *
+ * This API is to be called by the smartreflex class driver to register itself
+ * with the smartreflex driver during init. Returns 0 on success else the
+ * error value.
+ */
+int sr_register_class(struct omap_sr_class_data *class_data)
+{
+ struct omap_sr *sr_info;
+
+ if (!class_data) {
+ pr_warning("%s:, Smartreflex class data passed is NULL\n",
+ __func__);
+ return -EINVAL;
+ }
+
+ if (sr_class) {
+ pr_warning("%s: Smartreflex class driver already registered\n",
+ __func__);
+ return -EBUSY;
+ }
+
+ sr_class = class_data;
+
+ /*
+ * Call into late init to do intializations that require
+ * both sr driver and sr class driver to be initiallized.
+ */
+ list_for_each_entry(sr_info, &sr_list, node)
+ sr_late_init(sr_info);
+
+ return 0;
+}
+
+/**
+ * omap_sr_enable() - API to enable SR clocks and to call into the
+ * registered smartreflex class enable API.
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to enable
+ * a particular smartreflex module. This API will do the initial
+ * configurations to turn on the smartreflex module and in turn call
+ * into the registered smartreflex class enable API.
+ */
+void omap_sr_enable(struct voltagedomain *voltdm)
+{
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return;
+ }
+
+ if (!sr->autocomp_active)
+ return;
+
+ if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {
+ dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+ "registered\n", __func__);
+ return;
+ }
+
+ sr_class->enable(sr);
+}
+
+/**
+ * omap_sr_disable() - API to disable SR without resetting the voltage
+ * processor voltage
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to disable
+ * a particular smartreflex module. This API will in turn call
+ * into the registered smartreflex class disable API. This API will tell
+ * the smartreflex class disable not to reset the VP voltage after
+ * disabling smartreflex.
+ */
+void omap_sr_disable(struct voltagedomain *voltdm)
+{
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return;
+ }
+
+ if (!sr->autocomp_active)
+ return;
+
+ if (!sr_class || !(sr_class->disable)) {
+ dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+ "registered\n", __func__);
+ return;
+ }
+
+ sr_class->disable(sr, 0);
+}
+
+/**
+ * omap_sr_disable_reset_volt() - API to disable SR and reset the
+ * voltage processor voltage
+ * @voltdm: VDD pointer to which the SR module to be configured belongs to.
+ *
+ * This API is to be called from the kernel in order to disable
+ * a particular smartreflex module. This API will in turn call
+ * into the registered smartreflex class disable API. This API will tell
+ * the smartreflex class disable to reset the VP voltage after
+ * disabling smartreflex.
+ */
+void omap_sr_disable_reset_volt(struct voltagedomain *voltdm)
+{
+ struct omap_sr *sr = _sr_lookup(voltdm);
+
+ if (IS_ERR(sr)) {
+ pr_warning("%s: omap_sr struct for voltdm not found\n", __func__);
+ return;
+ }
+
+ if (!sr->autocomp_active)
+ return;
+
+ if (!sr_class || !(sr_class->disable)) {
+ dev_warn(&sr->pdev->dev, "%s: smartreflex class driver not"
+ "registered\n", __func__);
+ return;
+ }
+
+ sr_class->disable(sr, 1);
+}
+
+/**
+ * omap_sr_register_pmic() - API to register pmic specific info.
+ * @pmic_data: The structure containing pmic specific data.
+ *
+ * This API is to be called from the PMIC specific code to register with
+ * smartreflex driver pmic specific info. Currently the only info required
+ * is the smartreflex init on the PMIC side.
+ */
+void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data)
+{
+ if (!pmic_data) {
+ pr_warning("%s: Trying to register NULL PMIC data structure"
+ "with smartreflex\n", __func__);
+ return;
+ }
+
+ sr_pmic_data = pmic_data;
+}
+
+/* PM Debug FS entries to enable and disable smartreflex. */
+static int omap_sr_autocomp_show(void *data, u64 *val)
+{
+ struct omap_sr *sr_info = data;
+
+ if (!sr_info) {
+ pr_warning("%s: omap_sr struct not found\n", __func__);
+ return -EINVAL;
+ }
+
+ *val = sr_info->autocomp_active;
+
+ return 0;
+}
+
+static int omap_sr_autocomp_store(void *data, u64 val)
+{
+ struct omap_sr *sr_info = data;
+
+ if (!sr_info) {
+ pr_warning("%s: omap_sr struct not found\n", __func__);
+ return -EINVAL;
+ }
+
+ /* Sanity check */
+ if (val > 1) {
+ pr_warning("%s: Invalid argument %lld\n", __func__, val);
+ return -EINVAL;
+ }
+
+ /* control enable/disable only if there is a delta in value */
+ if (sr_info->autocomp_active != val) {
+ if (!val)
+ sr_stop_vddautocomp(sr_info);
+ else
+ sr_start_vddautocomp(sr_info);
+ }
+
+ return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(pm_sr_fops, omap_sr_autocomp_show,
+ omap_sr_autocomp_store, "%llu\n");
+
+static int __init omap_sr_probe(struct platform_device *pdev)
+{
+ struct omap_sr *sr_info;
+ struct omap_sr_data *pdata = pdev->dev.platform_data;
+ struct resource *mem, *irq;
+ struct dentry *nvalue_dir;
+ int i, ret = 0;
+
+ sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
+ if (!sr_info) {
+ dev_err(&pdev->dev, "%s: unable to allocate sr_info\n",
+ __func__);
+ return -ENOMEM;
+ }
+
+ platform_set_drvdata(pdev, sr_info);
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+ ret = -EINVAL;
+ goto err_free_devinfo;
+ }
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!mem) {
+ dev_err(&pdev->dev, "%s: no mem resource\n", __func__);
+ ret = -ENODEV;
+ goto err_free_devinfo;
+ }
+
+ mem = request_mem_region(mem->start, resource_size(mem),
+ dev_name(&pdev->dev));
+ if (!mem) {
+ dev_err(&pdev->dev, "%s: no mem region\n", __func__);
+ ret = -EBUSY;
+ goto err_free_devinfo;
+ }
+
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_irq_safe(&pdev->dev);
+
+ sr_info->name = kasprintf(GFP_KERNEL, "sr_%s", pdata->name);
+ if (!sr_info->name) {
+ dev_err(&pdev->dev, "%s: Unable to alloc SR instance name\n",
+ __func__);
+ ret = -ENOMEM;
+ goto err_release_region;
+ }
+
+ sr_info->pdev = pdev;
+ sr_info->srid = pdev->id;
+ sr_info->voltdm = pdata->voltdm;
+ sr_info->nvalue_table = pdata->nvalue_table;
+ sr_info->nvalue_count = pdata->nvalue_count;
+ sr_info->senn_mod = pdata->senn_mod;
+ sr_info->senp_mod = pdata->senp_mod;
+ sr_info->autocomp_active = false;
+ sr_info->ip_type = pdata->ip_type;
+ sr_info->base = ioremap(mem->start, resource_size(mem));
+ if (!sr_info->base) {
+ dev_err(&pdev->dev, "%s: ioremap fail\n", __func__);
+ ret = -ENOMEM;
+ goto err_release_region;
+ }
+
+ if (irq)
+ sr_info->irq = irq->start;
+
+ sr_set_clk_length(sr_info);
+ sr_set_regfields(sr_info);
+
+ list_add(&sr_info->node, &sr_list);
+
+ /*
+ * Call into late init to do intializations that require
+ * both sr driver and sr class driver to be initiallized.
+ */
+ if (sr_class) {
+ ret = sr_late_init(sr_info);
+ if (ret) {
+ pr_warning("%s: Error in SR late init\n", __func__);
+ goto err_iounmap;
+ }
+ }
+
+ dev_info(&pdev->dev, "%s: SmartReflex driver initialized\n", __func__);
+ if (!sr_dbg_dir) {
+ sr_dbg_dir = debugfs_create_dir("smartreflex", NULL);
+ if (IS_ERR_OR_NULL(sr_dbg_dir)) {
+ ret = PTR_ERR(sr_dbg_dir);
+ pr_err("%s:sr debugfs dir creation failed(%d)\n",
+ __func__, ret);
+ goto err_iounmap;
+ }
+ }
+
+ sr_info->dbg_dir = debugfs_create_dir(sr_info->name, sr_dbg_dir);
+ if (IS_ERR_OR_NULL(sr_info->dbg_dir)) {
+ dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n",
+ __func__);
+ ret = PTR_ERR(sr_info->dbg_dir);
+ goto err_free_name;
+ }
+
+ (void) debugfs_create_file("autocomp", S_IRUGO | S_IWUSR,
+ sr_info->dbg_dir, (void *)sr_info, &pm_sr_fops);
+ (void) debugfs_create_x32("errweight", S_IRUGO, sr_info->dbg_dir,
+ &sr_info->err_weight);
+ (void) debugfs_create_x32("errmaxlimit", S_IRUGO, sr_info->dbg_dir,
+ &sr_info->err_maxlimit);
+
+ nvalue_dir = debugfs_create_dir("nvalue", sr_info->dbg_dir);
+ if (IS_ERR_OR_NULL(nvalue_dir)) {
+ dev_err(&pdev->dev, "%s: Unable to create debugfs directory"
+ "for n-values\n", __func__);
+ ret = PTR_ERR(nvalue_dir);
+ goto err_debugfs;
+ }
+
+ if (sr_info->nvalue_count == 0 || !sr_info->nvalue_table) {
+ dev_warn(&pdev->dev, "%s: %s: No Voltage table for the corresponding vdd. Cannot create debugfs entries for n-values\n",
+ __func__, sr_info->name);
+ ret = -ENODATA;
+ goto err_debugfs;
+ }
+
+ for (i = 0; i < sr_info->nvalue_count; i++) {
+ char name[NVALUE_NAME_LEN + 1];
+
+ snprintf(name, sizeof(name), "volt_%lu",
+ sr_info->nvalue_table[i].volt_nominal);
+ (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
+ &(sr_info->nvalue_table[i].nvalue));
+ snprintf(name, sizeof(name), "errminlimit_%lu",
+ sr_info->nvalue_table[i].volt_nominal);
+ (void) debugfs_create_x32(name, S_IRUGO | S_IWUSR, nvalue_dir,
+ &(sr_info->nvalue_table[i].errminlimit));
+ }
+
+ return ret;
+
+err_debugfs:
+ debugfs_remove_recursive(sr_info->dbg_dir);
+err_free_name:
+ kfree(sr_info->name);
+err_iounmap:
+ list_del(&sr_info->node);
+ iounmap(sr_info->base);
+err_release_region:
+ release_mem_region(mem->start, resource_size(mem));
+err_free_devinfo:
+ kfree(sr_info);
+
+ return ret;
+}
+
+static int __devexit omap_sr_remove(struct platform_device *pdev)
+{
+ struct omap_sr_data *pdata = pdev->dev.platform_data;
+ struct omap_sr *sr_info;
+ struct resource *mem;
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+ return -EINVAL;
+ }
+
+ sr_info = _sr_lookup(pdata->voltdm);
+ if (IS_ERR(sr_info)) {
+ dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
+ __func__);
+ return PTR_ERR(sr_info);
+ }
+
+ if (sr_info->autocomp_active)
+ sr_stop_vddautocomp(sr_info);
+ if (sr_info->dbg_dir)
+ debugfs_remove_recursive(sr_info->dbg_dir);
+
+ list_del(&sr_info->node);
+ iounmap(sr_info->base);
+ kfree(sr_info->name);
+ kfree(sr_info);
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(mem->start, resource_size(mem));
+
+ return 0;
+}
+
+static void __devexit omap_sr_shutdown(struct platform_device *pdev)
+{
+ struct omap_sr_data *pdata = pdev->dev.platform_data;
+ struct omap_sr *sr_info;
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "%s: platform data missing\n", __func__);
+ return;
+ }
+
+ sr_info = _sr_lookup(pdata->voltdm);
+ if (IS_ERR(sr_info)) {
+ dev_warn(&pdev->dev, "%s: omap_sr struct not found\n",
+ __func__);
+ return;
+ }
+
+ if (sr_info->autocomp_active)
+ sr_stop_vddautocomp(sr_info);
+
+ return;
+}
+
+static struct platform_driver smartreflex_driver = {
+ .remove = __devexit_p(omap_sr_remove),
+ .shutdown = __devexit_p(omap_sr_shutdown),
+ .driver = {
+ .name = "smartreflex",
+ },
+};
+
+static int __init sr_init(void)
+{
+ int ret = 0;
+
+ /*
+ * sr_init is a late init. If by then a pmic specific API is not
+ * registered either there is no need for anything to be done on
+ * the PMIC side or somebody has forgotten to register a PMIC
+ * handler. Warn for the second condition.
+ */
+ if (sr_pmic_data && sr_pmic_data->sr_pmic_init)
+ sr_pmic_data->sr_pmic_init();
+ else
+ pr_warning("%s: No PMIC hook to init smartreflex\n", __func__);
+
+ ret = platform_driver_probe(&smartreflex_driver, omap_sr_probe);
+ if (ret) {
+ pr_err("%s: platform driver register failed for SR\n",
+ __func__);
+ return ret;
+ }
+
+ return 0;
+}
+late_initcall(sr_init);
+
+static void __exit sr_exit(void)
+{
+ platform_driver_unregister(&smartreflex_driver);
+}
+module_exit(sr_exit);
+
+MODULE_DESCRIPTION("OMAP Smartreflex Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_AUTHOR("Texas Instruments Inc");
diff --git a/drivers/power/avs/smartreflex.h b/drivers/power/avs/smartreflex.h
new file mode 100644
index 0000000..754f6aa
--- /dev/null
+++ b/drivers/power/avs/smartreflex.h
@@ -0,0 +1,238 @@
+/*
+ * OMAP Smartreflex Defines and Routines
+ *
+ * Author: Thara Gopinath <thara@...com>
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ * Thara Gopinath <thara@...com>
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@...com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __DRIVERS_POWER_AVS_SMARTREFLEX_H
+#define __DRIVERS_POWER_AVS_SMARTREFLEX_H
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/power/smartreflex.h>
+
+#include <plat/voltage.h>
+
+/*
+ * Different Smartreflex IPs version. The v1 is the 65nm version used in
+ * OMAP3430. The v2 is the update for the 45nm version of the IP
+ * used in OMAP3630 and OMAP4430
+ */
+#define SR_TYPE_V1 1
+#define SR_TYPE_V2 2
+
+/* SMART REFLEX REG ADDRESS OFFSET */
+#define SRCONFIG 0x00
+#define SRSTATUS 0x04
+#define SENVAL 0x08
+#define SENMIN 0x0C
+#define SENMAX 0x10
+#define SENAVG 0x14
+#define AVGWEIGHT 0x18
+#define NVALUERECIPROCAL 0x1c
+#define SENERROR_V1 0x20
+#define ERRCONFIG_V1 0x24
+#define IRQ_EOI 0x20
+#define IRQSTATUS_RAW 0x24
+#define IRQSTATUS 0x28
+#define IRQENABLE_SET 0x2C
+#define IRQENABLE_CLR 0x30
+#define SENERROR_V2 0x34
+#define ERRCONFIG_V2 0x38
+
+/* Bit/Shift Positions */
+
+/* SRCONFIG */
+#define SRCONFIG_ACCUMDATA_SHIFT 22
+#define SRCONFIG_SRCLKLENGTH_SHIFT 12
+#define SRCONFIG_SENNENABLE_V1_SHIFT 5
+#define SRCONFIG_SENPENABLE_V1_SHIFT 3
+#define SRCONFIG_SENNENABLE_V2_SHIFT 1
+#define SRCONFIG_SENPENABLE_V2_SHIFT 0
+#define SRCONFIG_CLKCTRL_SHIFT 0
+
+#define SRCONFIG_ACCUMDATA_MASK (0x3ff << 22)
+
+#define SRCONFIG_SRENABLE BIT(11)
+#define SRCONFIG_SENENABLE BIT(10)
+#define SRCONFIG_ERRGEN_EN BIT(9)
+#define SRCONFIG_MINMAXAVG_EN BIT(8)
+#define SRCONFIG_DELAYCTRL BIT(2)
+
+/* AVGWEIGHT */
+#define AVGWEIGHT_SENPAVGWEIGHT_SHIFT 2
+#define AVGWEIGHT_SENNAVGWEIGHT_SHIFT 0
+
+/* NVALUERECIPROCAL */
+#define NVALUERECIPROCAL_SENPGAIN_SHIFT 20
+#define NVALUERECIPROCAL_SENNGAIN_SHIFT 16
+#define NVALUERECIPROCAL_RNSENP_SHIFT 8
+#define NVALUERECIPROCAL_RNSENN_SHIFT 0
+
+/* ERRCONFIG */
+#define ERRCONFIG_ERRWEIGHT_SHIFT 16
+#define ERRCONFIG_ERRMAXLIMIT_SHIFT 8
+#define ERRCONFIG_ERRMINLIMIT_SHIFT 0
+
+#define SR_ERRWEIGHT_MASK (0x07 << 16)
+#define SR_ERRMAXLIMIT_MASK (0xff << 8)
+#define SR_ERRMINLIMIT_MASK (0xff << 0)
+
+#define ERRCONFIG_VPBOUNDINTEN_V1 BIT(31)
+#define ERRCONFIG_VPBOUNDINTST_V1 BIT(30)
+#define ERRCONFIG_MCUACCUMINTEN BIT(29)
+#define ERRCONFIG_MCUACCUMINTST BIT(28)
+#define ERRCONFIG_MCUVALIDINTEN BIT(27)
+#define ERRCONFIG_MCUVALIDINTST BIT(26)
+#define ERRCONFIG_MCUBOUNDINTEN BIT(25)
+#define ERRCONFIG_MCUBOUNDINTST BIT(24)
+#define ERRCONFIG_MCUDISACKINTEN BIT(23)
+#define ERRCONFIG_VPBOUNDINTST_V2 BIT(23)
+#define ERRCONFIG_MCUDISACKINTST BIT(22)
+#define ERRCONFIG_VPBOUNDINTEN_V2 BIT(22)
+
+#define ERRCONFIG_STATUS_V1_MASK (ERRCONFIG_VPBOUNDINTST_V1 | \
+ ERRCONFIG_MCUACCUMINTST | \
+ ERRCONFIG_MCUVALIDINTST | \
+ ERRCONFIG_MCUBOUNDINTST | \
+ ERRCONFIG_MCUDISACKINTST)
+/* IRQSTATUS */
+#define IRQSTATUS_MCUACCUMINT BIT(3)
+#define IRQSTATUS_MCVALIDINT BIT(2)
+#define IRQSTATUS_MCBOUNDSINT BIT(1)
+#define IRQSTATUS_MCUDISABLEACKINT BIT(0)
+
+/* IRQENABLE_SET and IRQENABLE_CLEAR */
+#define IRQENABLE_MCUACCUMINT BIT(3)
+#define IRQENABLE_MCUVALIDINT BIT(2)
+#define IRQENABLE_MCUBOUNDSINT BIT(1)
+#define IRQENABLE_MCUDISABLEACKINT BIT(0)
+
+/* Common Bit values */
+
+#define SRCLKLENGTH_12MHZ_SYSCLK 0x3c
+#define SRCLKLENGTH_13MHZ_SYSCLK 0x41
+#define SRCLKLENGTH_19MHZ_SYSCLK 0x60
+#define SRCLKLENGTH_26MHZ_SYSCLK 0x82
+#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0
+
+/*
+ * 3430 specific values. Maybe these should be passed from board file or
+ * pmic structures.
+ */
+#define OMAP3430_SR_ACCUMDATA 0x1f4
+
+#define OMAP3430_SR1_SENPAVGWEIGHT 0x03
+#define OMAP3430_SR1_SENNAVGWEIGHT 0x03
+
+#define OMAP3430_SR2_SENPAVGWEIGHT 0x01
+#define OMAP3430_SR2_SENNAVGWEIGHT 0x01
+
+#define OMAP3430_SR_ERRWEIGHT 0x04
+#define OMAP3430_SR_ERRMAXLIMIT 0x02
+
+/**
+ * test_cond_timeout - busy-loop, testing a condition
+ * @cond: condition to test until it evaluates to true
+ * @timeout: maximum number of microseconds in the timeout
+ * @index: loop index (integer)
+ *
+ * Loop waiting for @cond to become true or until at least @timeout
+ * microseconds have passed. To use, define some integer @index in the
+ * calling code. After running, if @index == @timeout, then the loop has
+ * timed out.
+ *
+ * Copied from omap_test_timeout
+ */
+#define sr_test_cond_timeout(cond, timeout, index) \
+({ \
+ for (index = 0; index < timeout; index++) { \
+ if (cond) \
+ break; \
+ udelay(1); \
+ } \
+})
+
+/**
+ * struct omap_sr_pmic_data - Strucutre to be populated by pmic code to pass
+ * pmic specific info to smartreflex driver
+ *
+ * @sr_pmic_init: API to initialize smartreflex on the PMIC side.
+ */
+struct omap_sr_pmic_data {
+ void (*sr_pmic_init) (void);
+};
+
+
+#ifdef CONFIG_POWER_AVS_OMAP
+/*
+ * The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR.
+ * The smartreflex class driver should pass the class type.
+ * Should be used to populate the class_type field of the
+ * omap_smartreflex_class_data structure.
+ */
+#define SR_CLASS1 0x1
+#define SR_CLASS2 0x2
+#define SR_CLASS3 0x3
+
+/**
+ * struct omap_sr_class_data - Smartreflex class driver info
+ *
+ * @enable: API to enable a particular class smaartreflex.
+ * @disable: API to disable a particular class smartreflex.
+ * @configure: API to configure a particular class smartreflex.
+ * @notify: API to notify the class driver about an event in SR.
+ * Not needed for class3.
+ * @notify_flags: specify the events to be notified to the class driver
+ * @class_type: specify which smartreflex class.
+ * Can be used by the SR driver to take any class
+ * based decisions.
+ */
+struct omap_sr_class_data {
+ int (*enable)(struct omap_sr *sr);
+ int (*disable)(struct omap_sr *sr, int is_volt_reset);
+ int (*configure)(struct omap_sr *sr);
+ int (*notify)(struct omap_sr *sr, u32 status);
+ u8 notify_flags;
+ u8 class_type;
+};
+
+/* Smartreflex module enable/disable interface */
+void omap_sr_enable(struct voltagedomain *voltdm);
+void omap_sr_disable(struct voltagedomain *voltdm);
+void omap_sr_disable_reset_volt(struct voltagedomain *voltdm);
+
+/* API to register the pmic specific data with the smartreflex driver. */
+void omap_sr_register_pmic(struct omap_sr_pmic_data *pmic_data);
+
+/* Smartreflex driver hooks to be called from Smartreflex class driver */
+int sr_enable(struct voltagedomain *voltdm, unsigned long volt);
+void sr_disable(struct voltagedomain *voltdm);
+int sr_configure_errgen(struct voltagedomain *voltdm);
+int sr_disable_errgen(struct voltagedomain *voltdm);
+int sr_configure_minmax(struct voltagedomain *voltdm);
+
+/* API to register the smartreflex class driver with the smartreflex driver */
+int sr_register_class(struct omap_sr_class_data *class_data);
+#else
+static inline void omap_sr_enable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable(struct voltagedomain *voltdm) {}
+static inline void omap_sr_disable_reset_volt(
+ struct voltagedomain *voltdm) {}
+static inline void omap_sr_register_pmic(
+ struct omap_sr_pmic_data *pmic_data) {}
+#endif
+#endif
--
1.7.5.4
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists