Message-ID: <1349089310-22134-1-git-send-email-sourav.poddar@ti.com>
Date:	Mon, 1 Oct 2012 16:31:50 +0530
From:	Sourav Poddar <sourav.poddar@...com>
To:	<devicetree-discuss@...ts.ozlabs.org>,
	<linux-arm-kernel@...ts.infradead.org>,
	<linux-omap@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
	<linux-input@...r.kernel.org>, <sourav.poddar@...com>
CC:	<b-cousson@...com>, <balbi@...com>, <santosh.shilimkar@...com>,
	<dmitry.torokhov@...il.com>
Subject: [PATCHv3 2/4] Input: keypad: Add smsc ece1099 keypad driver

From: G, Manjunath Kondaiah <manjugk@...com>

SMSC ECE1099 is a keyboard scan or GPIO expansion device.The device
supports a keypad scan matrix of 23*8.This driver uses this
device as a keypad driver.

Tested on omap5430 evm with 3.6-rc6 custom kernel.

Cc: Dmitry Torokhov <dmitry.torokhov@...il.com>
Cc: Benoit Cousson <b-cousson@...com>
Cc: Felipe Balbi <balbi@...com>
Cc: Santosh Shilimkar <santosh.shilimkar@...com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@...com>
Signed-off-by: Sourav Poddar <sourav.poddar@...com>
Acked-by: Felipe Balbi <balbi@...com>
---
Changes since v2:
 - Replace magic numbers through driver variable.
 - Provide comments for some initialisation done in probe.
 drivers/input/keyboard/Kconfig               |   11 +
 drivers/input/keyboard/Makefile              |    1 +
 drivers/input/keyboard/smsc-ece1099-keypad.c |  304 ++++++++++++++++++++++++++
 3 files changed, 316 insertions(+), 0 deletions(-)
 create mode 100644 drivers/input/keyboard/smsc-ece1099-keypad.c

diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
index c50fa75..b03a39c 100644
--- a/drivers/input/keyboard/Kconfig
+++ b/drivers/input/keyboard/Kconfig
@@ -593,6 +593,17 @@ config KEYBOARD_TWL4030
 	  To compile this driver as a module, choose M here: the
 	  module will be called twl4030_keypad.
 
+config KEYBOARD_SMSC
+       tristate "SMSC ECE1099 keypad support"
+       depends on I2C
+       help
+         Say Y here if your board use the smsc keypad controller
+         for omap5 defconfig. It's safe to say enable this
+         even on boards that don't use the keypad controller.
+
+         To compile this driver as a module, choose M here: the
+         module will be called smsc-ece1099-keypad.
+
 config KEYBOARD_XTKBD
 	tristate "XT keyboard"
 	select SERIO
diff --git a/drivers/input/keyboard/Makefile b/drivers/input/keyboard/Makefile
index 44e7600..0f2aa26 100644
--- a/drivers/input/keyboard/Makefile
+++ b/drivers/input/keyboard/Makefile
@@ -52,5 +52,6 @@ obj-$(CONFIG_KEYBOARD_TC3589X)		+= tc3589x-keypad.o
 obj-$(CONFIG_KEYBOARD_TEGRA)		+= tegra-kbc.o
 obj-$(CONFIG_KEYBOARD_TNETV107X)	+= tnetv107x-keypad.o
 obj-$(CONFIG_KEYBOARD_TWL4030)		+= twl4030_keypad.o
+obj-$(CONFIG_KEYBOARD_SMSC)            += smsc-ece1099-keypad.o
 obj-$(CONFIG_KEYBOARD_XTKBD)		+= xtkbd.o
 obj-$(CONFIG_KEYBOARD_W90P910)		+= w90p910_keypad.o
diff --git a/drivers/input/keyboard/smsc-ece1099-keypad.c b/drivers/input/keyboard/smsc-ece1099-keypad.c
new file mode 100644
index 0000000..15dc147
--- /dev/null
+++ b/drivers/input/keyboard/smsc-ece1099-keypad.c
@@ -0,0 +1,304 @@
+/*
+ * SMSC_ECE1099 Keypad driver
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/input/matrix_keypad.h>
+#include <linux/delay.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/smsc.h>
+#include <linux/of_gpio.h>
+#include <linux/of.h>
+
+#define KEYPRESS_TIME          200
+
+struct smsc_keypad {
+	struct smsc *smsc;
+	struct matrix_keymap_data *keymap_data;
+	unsigned int last_key_state[16];
+	unsigned int last_col;
+	unsigned int last_key_ms[16];
+	unsigned short *keymap;
+	struct i2c_client *client;
+	struct input_dev *input;
+	int rows, cols;
+	int row_shift;
+	bool no_autorepeat;
+	unsigned        irq;
+	struct device *dev;
+};
+
+static void smsc_kp_scan(struct smsc_keypad *kp)
+{
+	struct input_dev *input = kp->input;
+	int i, j;
+	int row, col;
+	int temp, code;
+	unsigned int new_state[16];
+	unsigned int bits_changed;
+	int this_ms;
+
+	smsc_write(kp->dev, SMSC_KP_INT_MASK, 0x00);
+	smsc_write(kp->dev, SMSC_KP_INT_STAT, 0xFF);
+
+	/* Scan for row and column */
+	for (i = 0; i < kp->cols; i++) {
+		smsc_write(kp->dev, SMSC_KP_OUT, SMSC_KSO_EVAL + i);
+		/* Read Row Status */
+		smsc_read(kp->dev, SMSC_KP_IN, &temp);
+		if (temp == 0xFF)
+			continue;
+
+		col = i;
+		for (j = 0; j < kp->rows; j++) {
+			if ((temp & 0x01) != 0x00) {
+				temp = temp >> 1;
+				continue;
+			}
+
+			row = j;
+			new_state[col] =  (1 << row);
+			bits_changed = kp->last_key_state[col] ^ new_state[col];
+			this_ms = jiffies_to_msecs(jiffies);
+			if (bits_changed != 0 || (!bits_changed &&
+					((this_ms - kp->last_key_ms[col]) >= KEYPRESS_TIME))) {
+				code = MATRIX_SCAN_CODE(row, col, kp->row_shift);
+				input_event(input, EV_MSC, MSC_SCAN, code);
+				input_report_key(input, kp->keymap[code], 1);
+				input_report_key(input, kp->keymap[code], 0);
+				kp->last_key_state[col] = new_state[col];
+				if (kp->last_col != col)
+					kp->last_key_state[kp->last_col] = 0;
+				kp->last_key_ms[col] = this_ms;
+			}
+			temp = temp >> 1;
+		}
+	}
+	input_sync(input);
+
+	smsc_write(kp->dev, SMSC_KP_INT_MASK, 0xFF);
+
+	/* Set up Low Power Mode (Wake-up) (0xFB) */
+	smsc_write(kp->dev, SMSC_WKUP_CTRL, SMSC_KP_SET_LOW_PWR);
+
+	/*Enable Keypad Scan (generate interrupt on key press) (0x40)*/
+	smsc_write(kp->dev, SMSC_KP_OUT, SMSC_KSO_ALL_LOW);
+}
+
+static irqreturn_t do_kp_irq(int irq, void *_kp)
+{
+	struct smsc_keypad *kp = _kp;
+	int int_status;
+
+	smsc_read(kp->dev, SMSC_KP_INT_STAT, &int_status);
+	if (int_status)
+		smsc_kp_scan(kp);
+
+	return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+static int __devinit smsc_keypad_parse_dt(struct device *dev,
+				struct smsc_keypad *kp)
+{
+	struct device_node *np = dev->of_node;
+
+	if (!np) {
+		dev_err(dev, "missing DT data");
+		return -EINVAL;
+	}
+
+	of_property_read_u32(np, "keypad,num-rows", &kp->rows);
+	of_property_read_u32(np, "keypad,num-columns", &kp->cols);
+	if (!kp->rows || !kp->cols) {
+		dev_err(dev, "number of keypad rows/columns not specified\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_bool(np, "linux,input-no-autorepeat"))
+		kp->no_autorepeat = true;
+
+	return 0;
+}
+#else
+static inline int smsc_keypad_parse_dt(struct device *dev,
+				struct smsc_keypad *kp)
+{
+	return -ENOSYS;
+}
+#endif
+
+static int __devinit
+smsc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct smsc *smsc = dev_get_drvdata(pdev->dev.parent);
+	struct input_dev *input;
+	struct smsc_keypad *kp;
+	int ret = 0, error;
+	int col, i, max_keys, row_shift;
+	int irq;
+	int addr;
+
+	kp = devm_kzalloc(dev, sizeof(*kp), GFP_KERNEL);
+
+	input = input_allocate_device();
+	if (!kp || !input) {
+		error = -ENOMEM;
+		goto err1;
+	}
+
+	error = smsc_keypad_parse_dt(&pdev->dev, kp);
+	if (error)
+		return error;
+
+	/* Get the debug Device */
+	kp->input = input;
+	kp->smsc = smsc;
+	kp->irq = platform_get_irq(pdev, 0);
+	kp->dev = dev;
+
+	for (col = 0; col < 16; col++) {
+		kp->last_key_state[col] = 0;
+		kp->last_key_ms[col] = 0;
+	}
+
+	/* setup input device */
+	 __set_bit(EV_KEY, input->evbit);
+
+	/* Enable auto repeat feature of Linux input subsystem */
+	if (!(kp->no_autorepeat))
+		__set_bit(EV_REP, input->evbit);
+
+	input_set_capability(input, EV_MSC, MSC_SCAN);
+	input->name             = "SMSC Keypad";
+	input->phys             = "smsc_keypad/input0";
+	input->dev.parent       = &pdev->dev;
+	input->id.bustype       = BUS_HOST;
+	input->id.vendor        = 0x0001;
+	input->id.product       = 0x0001;
+	input->id.version       = 0x0003;
+
+	error = input_register_device(input);
+	if (error) {
+		dev_err(kp->dev,
+			"Unable to register twl4030 keypad device\n");
+		goto err1;
+	}
+
+	/* Mask all GPIO interrupts (0x37-0x3B) */
+	for (addr = SMSC_GPIO_INT_MASK_START;
+			addr < SMSC_GPIO_INT_MASK_START + 4; addr++)
+		smsc_write(dev, addr, 0);
+
+	/* Set all outputs high (0x05-0x09) */
+	for (addr = SMSC_GPIO_DATA_OUT_START;
+			addr < SMSC_GPIO_DATA_OUT_START + 4; addr++)
+		smsc_write(dev, addr, 0xff);
+
+	/* Clear all GPIO interrupts (0x32-0x36) */
+	for (addr = SMSC_GPIO_INT_STAT_START;
+			addr < SMSC_GPIO_INT_STAT_START + 4; addr++)
+		smsc_write(dev, addr, 0xff);
+
+	/* Configure the smsc pins as Keyboard scan Input */
+	for (i = 0; i <= kp->rows; i++) {
+		addr = 0x12 + i;
+		smsc_write(dev, addr, SMSC_KP_KSI);
+	}
+
+	/* Configure the smsc pins as Keyboard scan output */
+	for (i = 0; i <= kp->cols; i++) {
+		addr = 0x1A + i;
+		smsc_write(dev, addr, SMSC_KP_KSO);
+	}
+
+	smsc_write(dev, SMSC_KP_INT_STAT, SMSC_KP_SET_HIGH);
+	smsc_write(dev, SMSC_WKUP_CTRL, SMSC_KP_SET_LOW_PWR);
+	smsc_write(dev, SMSC_KP_OUT, SMSC_KSO_ALL_LOW);
+
+	row_shift = get_count_order(kp->cols);
+	max_keys = kp->rows << row_shift;
+
+	kp->row_shift = row_shift;
+	kp->keymap = devm_kzalloc(dev, max_keys * sizeof(kp->keymap[0]),
+					GFP_KERNEL);
+	if (!kp->keymap) {
+		dev_err(&pdev->dev, "Not enough memory for keymap\n");
+		error = -ENOMEM;
+	}
+
+	matrix_keypad_build_keymap(NULL, NULL, kp->rows,
+			kp->cols, kp->keymap, input);
+
+	/*
+	* This ISR will always execute in kernel thread context because of
+	* the need to access the SMSC over the I2C bus.
+	*/
+	ret = devm_request_threaded_irq(dev, kp->irq, NULL, do_kp_irq,
+			IRQF_TRIGGER_FALLING | IRQF_ONESHOT, pdev->name, kp);
+	if (ret) {
+		dev_dbg(&pdev->dev, "request_irq failed for irq no=%d\n",
+			irq);
+		goto err2;
+	}
+
+	/* Enable smsc keypad interrupts */
+	ret = smsc_write(dev, SMSC_KP_INT_MASK, 0xff);
+	if (ret < 0)
+		goto err2;
+
+	return 0;
+
+err2:
+	input_unregister_device(input);
+err1:
+	input_free_device(input);
+	return ret;
+}
+
+static int __devexit smsc_remove(struct platform_device *pdev)
+{
+	struct smsc_keypad *kp = platform_get_drvdata(pdev);
+	input_unregister_device(kp->input);
+
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id smsc_keypad_dt_match[] = {
+	{ .compatible = "smsc,keypad" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, smsc_keypad_dt_match);
+#endif
+
+static struct platform_driver smsc_driver = {
+	.driver = {
+		.name	= "smsc-keypad",
+		.of_match_table = of_match_ptr(smsc_keypad_dt_match),
+		.owner  = THIS_MODULE,
+	},
+	.probe		= smsc_probe,
+	.remove		= __devexit_p(smsc_remove),
+};
+
+module_platform_driver(smsc_driver);
+
+MODULE_AUTHOR("G Kondaiah Manjunath <manjugk@...com>");
+MODULE_DESCRIPTION("SMSC ECE1099 Keypad driver");
+MODULE_LICENSE("GPL v2");
-- 
1.7.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/

Powered by blists - more mailing lists