| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <1351421337.2008.3.camel@joe-AO722>
Date: Sun, 28 Oct 2012 03:48:57 -0700
From: Joe Perches <joe@...ches.com>
To: Lucas Tavares <lucaskt@...ux.vnet.ibm.com>
Cc: Alan Cox <alan@...ux.intel.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
linux-serial@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [PATCH] jsm: Convert jsm_printk to jsm_dbg
These printks should all be emitted at KERN_DEBUG level.
Make them dependent on CONFIG_DEBUG or (#define DEBUG)
simplify the code a bit.
Add missing newlines where appropriate.
Most all of these messages could be deleted too.
Signed-off-by: Joe Perches <joe@...ches.com>
---
drivers/tty/serial/jsm/jsm.h | 8 ++-
drivers/tty/serial/jsm/jsm_driver.c | 3 +-
drivers/tty/serial/jsm/jsm_neo.c | 116 +++++++++++++++++++----------------
drivers/tty/serial/jsm/jsm_tty.c | 102 ++++++++++++++++---------------
4 files changed, 120 insertions(+), 109 deletions(-)
diff --git a/drivers/tty/serial/jsm/jsm.h b/drivers/tty/serial/jsm/jsm.h
index 529bec6..844d5e4 100644
--- a/drivers/tty/serial/jsm/jsm.h
+++ b/drivers/tty/serial/jsm/jsm.h
@@ -57,9 +57,11 @@ enum {
DBG_CARR = 0x10000,
};
-#define jsm_printk(nlevel, klevel, pdev, fmt, args...) \
- if ((DBG_##nlevel & jsm_debug)) \
- dev_printk(KERN_##klevel, pdev->dev, fmt, ## args)
+#define jsm_dbg(nlevel, pdev, fmt, ...) \
+do { \
+ if (DBG_##nlevel & jsm_debug) \
+ dev_dbg(pdev->dev, fmt, ##__VA_ARGS__); \
+} while (0)
#define MAXLINES 256
#define MAXPORTS 8
diff --git a/drivers/tty/serial/jsm/jsm_driver.c b/drivers/tty/serial/jsm/jsm_driver.c
index 5ab3c3b..8e05ce9 100644
--- a/drivers/tty/serial/jsm/jsm_driver.c
+++ b/drivers/tty/serial/jsm/jsm_driver.c
@@ -107,8 +107,7 @@ static int __devinit jsm_probe_one(struct pci_dev *pdev, const struct pci_device
brd->irq = pdev->irq;
- jsm_printk(INIT, INFO, &brd->pci_dev,
- "jsm_found_board - NEO adapter\n");
+ jsm_dbg(INIT, &brd->pci_dev, "jsm_found_board - NEO adapter\n");
/* get the PCI Base Address Registers */
brd->membase = pci_resource_start(pdev, 0);
diff --git a/drivers/tty/serial/jsm/jsm_neo.c b/drivers/tty/serial/jsm/jsm_neo.c
index 81dfafa..dfaf488 100644
--- a/drivers/tty/serial/jsm/jsm_neo.c
+++ b/drivers/tty/serial/jsm/jsm_neo.c
@@ -52,7 +52,7 @@ static void neo_set_cts_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting CTSFLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting CTSFLOW\n");
/* Turn on auto CTS flow control */
ier |= (UART_17158_IER_CTSDSR);
@@ -83,7 +83,7 @@ static void neo_set_rts_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting RTSFLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting RTSFLOW\n");
/* Turn on auto RTS flow control */
ier |= (UART_17158_IER_RTSDTR);
@@ -123,7 +123,7 @@ static void neo_set_ixon_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting IXON FLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting IXON FLOW\n");
/* Turn off auto CTS flow control */
ier &= ~(UART_17158_IER_CTSDSR);
@@ -160,7 +160,7 @@ static void neo_set_ixoff_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Setting IXOFF FLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Setting IXOFF FLOW\n");
/* Turn off auto RTS flow control */
ier &= ~(UART_17158_IER_RTSDTR);
@@ -198,7 +198,7 @@ static void neo_set_no_input_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Unsetting Input FLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Unsetting Input FLOW\n");
/* Turn off auto RTS flow control */
ier &= ~(UART_17158_IER_RTSDTR);
@@ -237,7 +237,7 @@ static void neo_set_no_output_flow_control(struct jsm_channel *ch)
ier = readb(&ch->ch_neo_uart->ier);
efr = readb(&ch->ch_neo_uart->efr);
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "Unsetting Output FLOW\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "Unsetting Output FLOW\n");
/* Turn off auto CTS flow control */
ier &= ~(UART_17158_IER_CTSDSR);
@@ -276,7 +276,7 @@ static inline void neo_set_new_start_stop_chars(struct jsm_channel *ch)
if (ch->ch_c_cflag & CRTSCTS)
return;
- jsm_printk(PARAM, INFO, &ch->ch_bd->pci_dev, "start\n");
+ jsm_dbg(PARAM, &ch->ch_bd->pci_dev, "start\n");
/* Tell UART what start/stop chars it should be looking for */
writeb(ch->ch_startc, &ch->ch_neo_uart->xonchar1);
@@ -455,7 +455,7 @@ static void neo_copy_data_from_uart_to_queue(struct jsm_channel *ch)
* I hope thats okay with everyone? Yes? Good.
*/
while (qleft < 1) {
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
"Queue full, dropping DATA:%x LSR:%x\n",
ch->ch_rqueue[tail], ch->ch_equeue[tail]);
@@ -467,8 +467,8 @@ static void neo_copy_data_from_uart_to_queue(struct jsm_channel *ch)
memcpy_fromio(ch->ch_rqueue + head, &ch->ch_neo_uart->txrxburst, 1);
ch->ch_equeue[head] = (u8) linestatus;
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
- "DATA/LSR pair: %x %x\n", ch->ch_rqueue[head], ch->ch_equeue[head]);
+ jsm_dbg(READ, &ch->ch_bd->pci_dev, "DATA/LSR pair: %x %x\n",
+ ch->ch_rqueue[head], ch->ch_equeue[head]);
/* Ditch any remaining linestatus value. */
linestatus = 0;
@@ -521,8 +521,8 @@ static void neo_copy_data_from_queue_to_uart(struct jsm_channel *ch)
ch->ch_cached_lsr &= ~(UART_LSR_THRE);
writeb(circ->buf[circ->tail], &ch->ch_neo_uart->txrx);
- jsm_printk(WRITE, INFO, &ch->ch_bd->pci_dev,
- "Tx data: %x\n", circ->buf[circ->tail]);
+ jsm_dbg(WRITE, &ch->ch_bd->pci_dev,
+ "Tx data: %x\n", circ->buf[circ->tail]);
circ->tail = (circ->tail + 1) & (UART_XMIT_SIZE - 1);
ch->ch_txcount++;
}
@@ -575,8 +575,9 @@ static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
{
u8 msignals = signals;
- jsm_printk(MSIGS, INFO, &ch->ch_bd->pci_dev,
- "neo_parse_modem: port: %d msignals: %x\n", ch->ch_portnum, msignals);
+ jsm_dbg(MSIGS, &ch->ch_bd->pci_dev,
+ "neo_parse_modem: port: %d msignals: %x\n",
+ ch->ch_portnum, msignals);
/* Scrub off lower bits. They signify delta's, which I don't care about */
/* Keep DDCD and DDSR though */
@@ -606,8 +607,8 @@ static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
else
ch->ch_mistat &= ~UART_MSR_CTS;
- jsm_printk(MSIGS, INFO, &ch->ch_bd->pci_dev,
- "Port: %d DTR: %d RTS: %d CTS: %d DSR: %d " "RI: %d CD: %d\n",
+ jsm_dbg(MSIGS, &ch->ch_bd->pci_dev,
+ "Port: %d DTR: %d RTS: %d CTS: %d DSR: %d " "RI: %d CD: %d\n",
ch->ch_portnum,
!!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_DTR),
!!((ch->ch_mistat | ch->ch_mostat) & UART_MCR_RTS),
@@ -649,8 +650,8 @@ static void neo_flush_uart_write(struct jsm_channel *ch)
/* Check to see if the UART feels it completely flushed the FIFO. */
tmp = readb(&ch->ch_neo_uart->isr_fcr);
if (tmp & 4) {
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
- "Still flushing TX UART... i: %d\n", i);
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
+ "Still flushing TX UART... i: %d\n", i);
udelay(10);
}
else
@@ -681,8 +682,8 @@ static void neo_flush_uart_read(struct jsm_channel *ch)
/* Check to see if the UART feels it completely flushed the FIFO. */
tmp = readb(&ch->ch_neo_uart->isr_fcr);
if (tmp & 2) {
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
- "Still flushing RX UART... i: %d\n", i);
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
+ "Still flushing RX UART... i: %d\n", i);
udelay(10);
}
else
@@ -705,8 +706,9 @@ static void neo_clear_break(struct jsm_channel *ch, int force)
writeb((temp & ~UART_LCR_SBC), &ch->ch_neo_uart->lcr);
ch->ch_flags &= ~(CH_BREAK_SENDING);
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev,
- "clear break Finishing UART_LCR_SBC! finished: %lx\n", jiffies);
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev,
+ "clear break Finishing UART_LCR_SBC! finished: %lx\n",
+ jiffies);
/* flush write operation */
neo_pci_posting_flush(ch->ch_bd);
@@ -748,8 +750,8 @@ static inline void neo_parse_isr(struct jsm_board *brd, u32 port)
*/
isr &= ~(UART_17158_IIR_FIFO_ENABLED);
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "%s:%d isr: %x\n", __FILE__, __LINE__, isr);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d isr: %x\n",
+ __FILE__, __LINE__, isr);
if (isr & (UART_17158_IIR_RDI_TIMEOUT | UART_IIR_RDI)) {
/* Read data from uart -> queue */
@@ -772,8 +774,9 @@ static inline void neo_parse_isr(struct jsm_board *brd, u32 port)
if (isr & UART_17158_IIR_XONXOFF) {
cause = readb(&ch->ch_neo_uart->xoffchar1);
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "Port %d. Got ISR_XONXOFF: cause:%x\n", port, cause);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "Port %d. Got ISR_XONXOFF: cause:%x\n",
+ port, cause);
/*
* Since the UART detected either an XON or
@@ -786,17 +789,19 @@ static inline void neo_parse_isr(struct jsm_board *brd, u32 port)
if (brd->channels[port]->ch_flags & CH_STOP) {
ch->ch_flags &= ~(CH_STOP);
}
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "Port %d. XON detected in incoming data\n", port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "Port %d. XON detected in incoming data\n",
+ port);
}
else if (cause == UART_17158_XOFF_DETECT) {
if (!(brd->channels[port]->ch_flags & CH_STOP)) {
ch->ch_flags |= CH_STOP;
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "Setting CH_STOP\n");
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "Setting CH_STOP\n");
}
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "Port: %d. XOFF detected in incoming data\n", port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "Port: %d. XOFF detected in incoming data\n",
+ port);
}
spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
}
@@ -825,8 +830,8 @@ static inline void neo_parse_isr(struct jsm_board *brd, u32 port)
}
/* Parse any modem signal changes */
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "MOD_STAT: sending to parse_modem_sigs\n");
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "MOD_STAT: sending to parse_modem_sigs\n");
neo_parse_modem(ch, readb(&ch->ch_neo_uart->msr));
}
}
@@ -849,8 +854,8 @@ static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
linestatus = readb(&ch->ch_neo_uart->lsr);
- jsm_printk(INTR, INFO, &ch->ch_bd->pci_dev,
- "%s:%d port: %d linestatus: %x\n", __FILE__, __LINE__, port, linestatus);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d port: %d linestatus: %x\n",
+ __FILE__, __LINE__, port, linestatus);
ch->ch_cached_lsr |= linestatus;
@@ -869,7 +874,7 @@ static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
*to do the special RX+LSR read for this FIFO load.
*/
if (linestatus & UART_17158_RX_FIFO_DATA_ERROR)
- jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
"%s:%d Port: %d Got an RX error, need to parse LSR\n",
__FILE__, __LINE__, port);
@@ -880,20 +885,21 @@ static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
if (linestatus & UART_LSR_PE) {
ch->ch_err_parity++;
- jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
- "%s:%d Port: %d. PAR ERR!\n", __FILE__, __LINE__, port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d Port: %d. PAR ERR!\n",
+ __FILE__, __LINE__, port);
}
if (linestatus & UART_LSR_FE) {
ch->ch_err_frame++;
- jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
- "%s:%d Port: %d. FRM ERR!\n", __FILE__, __LINE__, port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev, "%s:%d Port: %d. FRM ERR!\n",
+ __FILE__, __LINE__, port);
}
if (linestatus & UART_LSR_BI) {
ch->ch_err_break++;
- jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
- "%s:%d Port: %d. BRK INTR!\n", __FILE__, __LINE__, port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "%s:%d Port: %d. BRK INTR!\n",
+ __FILE__, __LINE__, port);
}
if (linestatus & UART_LSR_OE) {
@@ -904,8 +910,9 @@ static inline void neo_parse_lsr(struct jsm_board *brd, u32 port)
* Probably we should eventually have an orun stat in our driver...
*/
ch->ch_err_overrun++;
- jsm_printk(INTR, DEBUG, &ch->ch_bd->pci_dev,
- "%s:%d Port: %d. Rx Overrun!\n", __FILE__, __LINE__, port);
+ jsm_dbg(INTR, &ch->ch_bd->pci_dev,
+ "%s:%d Port: %d. Rx Overrun!\n",
+ __FILE__, __LINE__, port);
}
if (linestatus & UART_LSR_THRE) {
@@ -1128,11 +1135,11 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
*/
uart_poll = readl(brd->re_map_membase + UART_17158_POLL_ADDR_OFFSET);
- jsm_printk(INTR, INFO, &brd->pci_dev,
- "%s:%d uart_poll: %x\n", __FILE__, __LINE__, uart_poll);
+ jsm_dbg(INTR, &brd->pci_dev, "%s:%d uart_poll: %x\n",
+ __FILE__, __LINE__, uart_poll);
if (!uart_poll) {
- jsm_printk(INTR, INFO, &brd->pci_dev,
+ jsm_dbg(INTR, &brd->pci_dev,
"Kernel interrupted to me, but no pending interrupts...\n");
spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
return IRQ_NONE;
@@ -1158,15 +1165,15 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
continue;
}
- jsm_printk(INTR, INFO, &brd->pci_dev,
- "%s:%d port: %x type: %x\n", __FILE__, __LINE__, port, type);
+ jsm_dbg(INTR, &brd->pci_dev, "%s:%d port: %x type: %x\n",
+ __FILE__, __LINE__, port, type);
/* Remove this port + type from uart_poll */
uart_poll &= ~(jsm_offset_table[port]);
if (!type) {
/* If no type, just ignore it, and move onto next port */
- jsm_printk(INTR, ERR, &brd->pci_dev,
+ jsm_dbg(INTR, &brd->pci_dev,
"Interrupt with no type! port: %d\n", port);
continue;
}
@@ -1231,15 +1238,16 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
* these once and awhile.
* Its harmless, just ignore it and move on.
*/
- jsm_printk(INTR, ERR, &brd->pci_dev,
- "%s:%d Unknown Interrupt type: %x\n", __FILE__, __LINE__, type);
+ jsm_dbg(INTR, &brd->pci_dev,
+ "%s:%d Unknown Interrupt type: %x\n",
+ __FILE__, __LINE__, type);
continue;
}
}
spin_unlock_irqrestore(&brd->bd_intr_lock, lock_flags);
- jsm_printk(INTR, INFO, &brd->pci_dev, "finish.\n");
+ jsm_dbg(INTR, &brd->pci_dev, "finish\n");
return IRQ_HANDLED;
}
diff --git a/drivers/tty/serial/jsm/jsm_tty.c b/drivers/tty/serial/jsm/jsm_tty.c
index 7139796..7d2c1f3 100644
--- a/drivers/tty/serial/jsm/jsm_tty.c
+++ b/drivers/tty/serial/jsm/jsm_tty.c
@@ -43,7 +43,7 @@ static inline int jsm_get_mstat(struct jsm_channel *ch)
unsigned char mstat;
unsigned result;
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev, "start\n");
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev, "start\n");
mstat = (ch->ch_mostat | ch->ch_mistat);
@@ -62,7 +62,7 @@ static inline int jsm_get_mstat(struct jsm_channel *ch)
if (mstat & UART_MSR_DCD)
result |= TIOCM_CD;
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev, "finish\n");
return result;
}
@@ -79,14 +79,14 @@ static unsigned int jsm_tty_get_mctrl(struct uart_port *port)
int result;
struct jsm_channel *channel = (struct jsm_channel *)port;
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "start\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "start\n");
result = jsm_get_mstat(channel);
if (result < 0)
return -ENXIO;
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "finish\n");
return result;
}
@@ -100,7 +100,7 @@ static void jsm_tty_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct jsm_channel *channel = (struct jsm_channel *)port;
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "start\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "start\n");
if (mctrl & TIOCM_RTS)
channel->ch_mostat |= UART_MCR_RTS;
@@ -114,7 +114,7 @@ static void jsm_tty_set_mctrl(struct uart_port *port, unsigned int mctrl)
channel->ch_bd->bd_ops->assert_modem_signals(channel);
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "finish\n");
udelay(10);
}
@@ -135,23 +135,23 @@ static void jsm_tty_start_tx(struct uart_port *port)
{
struct jsm_channel *channel = (struct jsm_channel *)port;
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "start\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "start\n");
channel->ch_flags &= ~(CH_STOP);
jsm_tty_write(port);
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "finish\n");
}
static void jsm_tty_stop_tx(struct uart_port *port)
{
struct jsm_channel *channel = (struct jsm_channel *)port;
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "start\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "start\n");
channel->ch_flags |= (CH_STOP);
- jsm_printk(IOCTL, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &channel->ch_bd->pci_dev, "finish\n");
}
static void jsm_tty_send_xchar(struct uart_port *port, char ch)
@@ -216,16 +216,16 @@ static int jsm_tty_open(struct uart_port *port)
if (!channel->ch_rqueue) {
channel->ch_rqueue = kzalloc(RQUEUESIZE, GFP_KERNEL);
if (!channel->ch_rqueue) {
- jsm_printk(INIT, ERR, &channel->ch_bd->pci_dev,
- "unable to allocate read queue buf");
+ jsm_dbg(INIT, &channel->ch_bd->pci_dev,
+ "unable to allocate read queue buf\n");
return -ENOMEM;
}
}
if (!channel->ch_equeue) {
channel->ch_equeue = kzalloc(EQUEUESIZE, GFP_KERNEL);
if (!channel->ch_equeue) {
- jsm_printk(INIT, ERR, &channel->ch_bd->pci_dev,
- "unable to allocate error queue buf");
+ jsm_dbg(INIT, &channel->ch_bd->pci_dev,
+ "unable to allocate error queue buf\n");
return -ENOMEM;
}
}
@@ -234,7 +234,7 @@ static int jsm_tty_open(struct uart_port *port)
/*
* Initialize if neither terminal is open.
*/
- jsm_printk(OPEN, INFO, &channel->ch_bd->pci_dev,
+ jsm_dbg(OPEN, &channel->ch_bd->pci_dev,
"jsm_open: initializing channel in open...\n");
/*
@@ -270,7 +270,7 @@ static int jsm_tty_open(struct uart_port *port)
channel->ch_open_count++;
- jsm_printk(OPEN, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(OPEN, &channel->ch_bd->pci_dev, "finish\n");
return 0;
}
@@ -280,7 +280,7 @@ static void jsm_tty_close(struct uart_port *port)
struct ktermios *ts;
struct jsm_channel *channel = (struct jsm_channel *)port;
- jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev, "start\n");
+ jsm_dbg(CLOSE, &channel->ch_bd->pci_dev, "start\n");
bd = channel->ch_bd;
ts = &port->state->port.tty->termios;
@@ -293,7 +293,7 @@ static void jsm_tty_close(struct uart_port *port)
* If we have HUPCL set, lower DTR and RTS
*/
if (channel->ch_c_cflag & HUPCL) {
- jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev,
+ jsm_dbg(CLOSE, &channel->ch_bd->pci_dev,
"Close. HUPCL set, dropping DTR/RTS\n");
/* Drop RTS/DTR */
@@ -304,7 +304,7 @@ static void jsm_tty_close(struct uart_port *port)
/* Turn off UART interrupts for this port */
channel->ch_bd->bd_ops->uart_off(channel);
- jsm_printk(CLOSE, INFO, &channel->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(CLOSE, &channel->ch_bd->pci_dev, "finish\n");
}
static void jsm_tty_set_termios(struct uart_port *port,
@@ -380,7 +380,7 @@ int __devinit jsm_tty_init(struct jsm_board *brd)
if (!brd)
return -ENXIO;
- jsm_printk(INIT, INFO, &brd->pci_dev, "start\n");
+ jsm_dbg(INIT, &brd->pci_dev, "start\n");
/*
* Initialize board structure elements.
@@ -401,9 +401,9 @@ int __devinit jsm_tty_init(struct jsm_board *brd)
*/
brd->channels[i] = kzalloc(sizeof(struct jsm_channel), GFP_KERNEL);
if (!brd->channels[i]) {
- jsm_printk(CORE, ERR, &brd->pci_dev,
+ jsm_dbg(CORE, &brd->pci_dev,
"%s:%d Unable to allocate memory for channel struct\n",
- __FILE__, __LINE__);
+ __FILE__, __LINE__);
}
}
}
@@ -431,7 +431,7 @@ int __devinit jsm_tty_init(struct jsm_board *brd)
init_waitqueue_head(&ch->ch_flags_wait);
}
- jsm_printk(INIT, INFO, &brd->pci_dev, "finish\n");
+ jsm_dbg(INIT, &brd->pci_dev, "finish\n");
return 0;
}
@@ -444,7 +444,7 @@ int jsm_uart_port_init(struct jsm_board *brd)
if (!brd)
return -ENXIO;
- jsm_printk(INIT, INFO, &brd->pci_dev, "start\n");
+ jsm_dbg(INIT, &brd->pci_dev, "start\n");
/*
* Initialize board structure elements.
@@ -481,7 +481,7 @@ int jsm_uart_port_init(struct jsm_board *brd)
printk(KERN_INFO "jsm: Port %d added\n", i);
}
- jsm_printk(INIT, INFO, &brd->pci_dev, "finish\n");
+ jsm_dbg(INIT, &brd->pci_dev, "finish\n");
return 0;
}
@@ -493,7 +493,7 @@ int jsm_remove_uart_port(struct jsm_board *brd)
if (!brd)
return -ENXIO;
- jsm_printk(INIT, INFO, &brd->pci_dev, "start\n");
+ jsm_dbg(INIT, &brd->pci_dev, "start\n");
/*
* Initialize board structure elements.
@@ -513,7 +513,7 @@ int jsm_remove_uart_port(struct jsm_board *brd)
uart_remove_one_port(&jsm_uart_driver, &brd->channels[i]->uart_port);
}
- jsm_printk(INIT, INFO, &brd->pci_dev, "finish\n");
+ jsm_dbg(INIT, &brd->pci_dev, "finish\n");
return 0;
}
@@ -531,7 +531,7 @@ void jsm_input(struct jsm_channel *ch)
int s = 0;
int i = 0;
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "start\n");
+ jsm_dbg(READ, &ch->ch_bd->pci_dev, "start\n");
if (!ch)
return;
@@ -560,7 +560,7 @@ void jsm_input(struct jsm_channel *ch)
return;
}
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "start\n");
+ jsm_dbg(READ, &ch->ch_bd->pci_dev, "start\n");
/*
*If the device is not open, or CREAD is off, flush
@@ -569,8 +569,9 @@ void jsm_input(struct jsm_channel *ch)
if (!tp ||
!(tp->termios.c_cflag & CREAD) ) {
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
- "input. dropping %d bytes on port %d...\n", data_len, ch->ch_portnum);
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
+ "input. dropping %d bytes on port %d...\n",
+ data_len, ch->ch_portnum);
ch->ch_r_head = tail;
/* Force queue flow control to be released, if needed */
@@ -585,17 +586,17 @@ void jsm_input(struct jsm_channel *ch)
*/
if (ch->ch_flags & CH_STOPI) {
spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
"Port %d throttled, not reading any data. head: %x tail: %x\n",
ch->ch_portnum, head, tail);
return;
}
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "start 2\n");
+ jsm_dbg(READ, &ch->ch_bd->pci_dev, "start 2\n");
if (data_len <= 0) {
spin_unlock_irqrestore(&ch->ch_lock, lock_flags);
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "jsm_input 1\n");
+ jsm_dbg(READ, &ch->ch_bd->pci_dev, "jsm_input 1\n");
return;
}
@@ -653,7 +654,7 @@ void jsm_input(struct jsm_channel *ch)
/* Tell the tty layer its okay to "eat" the data now */
tty_flip_buffer_push(tp);
- jsm_printk(IOCTL, INFO, &ch->ch_bd->pci_dev, "finish\n");
+ jsm_dbg(IOCTL, &ch->ch_bd->pci_dev, "finish\n");
}
static void jsm_carrier(struct jsm_channel *ch)
@@ -663,7 +664,7 @@ static void jsm_carrier(struct jsm_channel *ch)
int virt_carrier = 0;
int phys_carrier = 0;
- jsm_printk(CARR, INFO, &ch->ch_bd->pci_dev, "start\n");
+ jsm_dbg(CARR, &ch->ch_bd->pci_dev, "start\n");
if (!ch)
return;
@@ -673,16 +674,16 @@ static void jsm_carrier(struct jsm_channel *ch)
return;
if (ch->ch_mistat & UART_MSR_DCD) {
- jsm_printk(CARR, INFO, &ch->ch_bd->pci_dev,
- "mistat: %x D_CD: %x\n", ch->ch_mistat, ch->ch_mistat & UART_MSR_DCD);
+ jsm_dbg(CARR, &ch->ch_bd->pci_dev, "mistat: %x D_CD: %x\n",
+ ch->ch_mistat, ch->ch_mistat & UART_MSR_DCD);
phys_carrier = 1;
}
if (ch->ch_c_cflag & CLOCAL)
virt_carrier = 1;
- jsm_printk(CARR, INFO, &ch->ch_bd->pci_dev,
- "DCD: physical: %d virt: %d\n", phys_carrier, virt_carrier);
+ jsm_dbg(CARR, &ch->ch_bd->pci_dev, "DCD: physical: %d virt: %d\n",
+ phys_carrier, virt_carrier);
/*
* Test for a VIRTUAL carrier transition to HIGH.
@@ -694,8 +695,7 @@ static void jsm_carrier(struct jsm_channel *ch)
* for carrier in the open routine.
*/
- jsm_printk(CARR, INFO, &ch->ch_bd->pci_dev,
- "carrier: virt DCD rose\n");
+ jsm_dbg(CARR, &ch->ch_bd->pci_dev, "carrier: virt DCD rose\n");
if (waitqueue_active(&(ch->ch_flags_wait)))
wake_up_interruptible(&ch->ch_flags_wait);
@@ -711,7 +711,7 @@ static void jsm_carrier(struct jsm_channel *ch)
* for carrier in the open routine.
*/
- jsm_printk(CARR, INFO, &ch->ch_bd->pci_dev,
+ jsm_dbg(CARR, &ch->ch_bd->pci_dev,
"carrier: physical DCD rose\n");
if (waitqueue_active(&(ch->ch_flags_wait)))
@@ -790,8 +790,8 @@ void jsm_check_queue_flow_control(struct jsm_channel *ch)
if(!(ch->ch_flags & CH_RECEIVER_OFF)) {
bd_ops->disable_receiver(ch);
ch->ch_flags |= (CH_RECEIVER_OFF);
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
- "Internal queue hit hilevel mark (%d)! Turning off interrupts.\n",
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
+ "Internal queue hit hilevel mark (%d)! Turning off interrupts\n",
qleft);
}
}
@@ -800,8 +800,9 @@ void jsm_check_queue_flow_control(struct jsm_channel *ch)
if (ch->ch_stops_sent <= MAX_STOPS_SENT) {
bd_ops->send_stop_character(ch);
ch->ch_stops_sent++;
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
- "Sending stop char! Times sent: %x\n", ch->ch_stops_sent);
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
+ "Sending stop char! Times sent: %x\n",
+ ch->ch_stops_sent);
}
}
}
@@ -827,8 +828,8 @@ void jsm_check_queue_flow_control(struct jsm_channel *ch)
if (ch->ch_flags & CH_RECEIVER_OFF) {
bd_ops->enable_receiver(ch);
ch->ch_flags &= ~(CH_RECEIVER_OFF);
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev,
- "Internal queue hit lowlevel mark (%d)! Turning on interrupts.\n",
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
+ "Internal queue hit lowlevel mark (%d)! Turning on interrupts\n",
qleft);
}
}
@@ -836,7 +837,8 @@ void jsm_check_queue_flow_control(struct jsm_channel *ch)
else if (ch->ch_c_iflag & IXOFF && ch->ch_stops_sent) {
ch->ch_stops_sent = 0;
bd_ops->send_start_character(ch);
- jsm_printk(READ, INFO, &ch->ch_bd->pci_dev, "Sending start char!\n");
+ jsm_dbg(READ, &ch->ch_bd->pci_dev,
+ "Sending start char!\n");
}
}
}
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@...r.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Powered by blists - more mailing lists